WWMDN4210DV1Wireless High Gain USB Adapter

PW-DN4210D Wireless High Gain USB Adapter PW-DN4210D Wireless High Gain USB Adapter PW-DN4210D Wireless High Gain USB Adapter FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user‟s authority to operate the equipment. In the U.S., Channel 12 and Channel 13 are banned to use according to the act of FCC. So please kindly make sure your AP is working on other channel before you use it. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance PW-DN4210D Wireless High Gain USB Adapter CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don‟t use the product outdoors in France. PW-DN4210D Wireless High Gain USB Adapter CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Overview of the product ........................................................................................................ 2 1.2 Features ................................................................................................................................ 2 1.3 LED Status ............................................................................................................................ 3 Chapter 2. Installation Guide ............................................................................... 4 2.1 Hardware Installation ............................................................................................................ 4 2.2 Software Installation .............................................................................................................. 4 2.2.1 For Windows XP ............................................................................................................ 4 2.2.2 For Windows Vista ......................................................................................................... 8 2.2.3 For Windows 7 ............................................................................................................. 11 Chapter 3. Configuration Guide ......................................................................... 14 3.1 For Windows XP ................................................................................................................. 14 3.1.1 Current Status .............................................................................................................. 14 3.1.2 Profile Management ..................................................................................................... 16 3.1.3 Diagnostics .................................................................................................................. 24 3.2 For Windows Vista .............................................................................................................. 25 3.3 For Windows 7 .................................................................................................................... 27 Chapter 4. WPS configuration ......................................................…

Text truncated - open the document above for the full version.

Attestation for FCC Declaration of Conformity FCC ID: WWMDN4210DV1 Date: Jul 27,2011 Please be notified that we, the undersigned, PROWARE Technologies Co., Ltd. declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is EM-F1000608, with is issued by an accredited lab, Audix Technology Corporation, EMC Department located at No. 53-11, Tin-Fu Tsun, Lin-Kou , Taipei Hsien , Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technologies Co., Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Web site: WWW.PROWARE.COM.CN PROWARE TECHNOLOGIES CO., LTD.

AGENCY AUTHORIZATION LETTER FCC ID:WWMDN4210DV1 Date:Jul 27,2011 To whom it may concern: We, the undersigned, hereby authorize Audix Technology (Shenzhen) Co., Ltd （No. 6, Ke Feng Rd., 52 Block， Shenzhen Science & Industrial Park,Nantou,Shenzhen, Guangdong, China） to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Audix within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months form original date. If you have any Questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technolog ies Co., Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Web site: WWW.PROWARE.COM.CN PROWARE TECHNOLOGIES CO., LTD.

Date: Jun 27,2011 Federal Communications Commission Authorization and Evaluation Division FCC ID:WWMDN4210DV1 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Block diagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might to harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technologies Co., Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Web site: WWW.PROWARE.COM.CN PROWARE TECHNOLOGIES CO., LTD.

R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-1 13. PHOTOS OF THE EUT Figure 1 General Appearance of the EUT Figure 2 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-2 Figure 3 General Appearance of the EUT Figure 4 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-3 Figure 5 General Appearance of the EUT Figure 6 General Appearance of the EUT

PW-DN4210D(MU3)产品规格标贴 第一版 100#合成纸+可打印雾膜 PW-DN4210D(MU3)\1.0\欧 2010-5-4 白色 PANTONE 426C 白色 王晓锋 1 2 E D C B A 1 2 3 4 5 6 7 8 9 E D C 3 4 5 6 7 8 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 记 录 与上一版的区别 1:1 39.7*9.7mm, 1R

R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-4 Figure 7 Inside of the EUT Figure 8 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-5 Figure 9 Inside of the EUT Figure 10 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 13-6 Figure 11 Inside of the EUT

Report No. RZA1106-1059SAR01R3 Page 1 of 76 TESTING No. L2264 TEST REPORT Product Name Wireless High Gain USB Adapter Model PW-DN4210D FCC ID WWMDN4210DV1 Client Proware Techologies Co., Ltd. TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No. RZA1106-1059SAR01R3 Page 2 of 76 GENERAL SUMMARY Product Name Wireless High Gain USB Adapter Model PW-DN4210D FCC ID WWMDN4210DV1 Report No. RZA1106-1059SAR01R3 Client Proware Techologies Co., Ltd. Manufacturer Proware Techologies Co., Ltd. Reference Standard(s) IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. SUPPLEMENT C Edition 01-01 to OET BULLETIN 65 Edition 97-01 June 2001 including DA 02-1438, published June 2002: Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields Additional Information for Evaluation Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radio frequency Emissions. KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. KDB 447498 D02 SAR Procedures for Dongle Xmtr v02: SAR Measurement Procedures for USB Dongle Transmitters. Tracking Number 258142 Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: October 31 st , 2011 Comment The test result only responds to the measured sample. Approved by Director Revised by SAR Manager Performed by SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No. RZA1106-1059SAR01R3 Page 3 of 76 TABLE OF CONTENT 1. General Information ........................................................................................................................ 5 1.1. Notes of the Test Report.......................................................................................................... 5 1.2. Testing Laboratory ................................................................................................................... 5 1.3. Applicant Information ............................................................................................................... 6 1.4. Manufacturer Information ......................................................................................................... 6 1.5. Information of EUT................................................................................................................... 7 1.6. The Maximum SAR 1g Values ................................................................................................... 8 1.7. Power of Each Tested Mode.................................................................................................... 8 1.8. Test Date ................................................................................................................................. 8 2. Operational Conditions during Test ................................................................................................. 9 2.1. General Description of Test Procedures .................................................................................. 9 2.2. Test Position of Portable Devices........................................................................................... 10 2.3. Picture of Host Product .......................................................................................................... 11 3. SAR Measurements System Configuration ................................................................................... 12 3.1. SAR Measurement Set-up .....................................................................................................12 3.2. DASY4 E-field Probe System ................................................................................................ 13 3.2.1. EX3DV4 Probe Specification .......................................................................................... 13 3.2.2. E-field Probe Calibration ................................................................................................. 14 3.3. Other Test Equipment ............................................................................................................14 3.3.1. Device Holder for Transmitters ....................................................................................... 14 3.3.2. Phantom .........................................................................................................................15 3.4. Scanning Procedure ..............................................................................................................15 3.5. Data Storage and Evaluation ................................................................................................. 17 3.5.1. Data Storage...................................................................................................................17 3.5.2. Data Evaluation by SEMCAD ......................................................................................... 17 3.6. System Check........................................................................................................................ 20 3.7. Equivalent Tissues ................................................................................................................. 22 4. Laboratory Environment................................................................................................................ 22 5. Characteristics of the Test ............................................................................................................. 23 5.1. Applicable Limit Regulations .................................................................................................. 23 5.2. Applicable Measurement Standards...........................................................…

Text truncated - open the document above for the full version.

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Proware Technologies Co., Ltd. Wireless High Gain USB Adapter Model No.: PW-DN4210D FCC ID: WWMDN4210DV1 Prepared for : Proware Technologies Co., Ltd. 2nd F1 East Wing, South Section, Factory Building 24, Science & Technology Park, Shennan Rd, Nanshan District, Shenzhen Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park, Nantou, Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number ： ACS-F11127 Date of Test ： Jun.28~Jul.03, 2011 Date of Report ： Jul.05, 2011 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS .......................................................... 1-1 1.1. Description of Standards and Results .................................................................................. 1-1 2. GENERAL INFORMATION ......................................................................................... 2-1 2.1. Description of Device (EUT) ............................................................................................... 2-1 2.2. Test Information ................................................................................................................... 2-2 2.3. Tested Supporting System Details ....................................................................................... 2-3 2.4. Block diagram of connection between the EUT and simulators .......................................... 2-3 2.5. Test Facility ......................................................................................................................... 2-4 2.6. Measurement Uncertainty (95% confidence levels, k=2) .................................................... 2-5 3. POWER LINE CONDUCTED EMISSION TEST ....................................................... 3-1 3.1. Test Equipments ................................................................................................................... 3-1 3.2. Block Diagram of Test Setup ............................................................................................... 3-1 3.3. Power Line Conducted Emission Test Limits ...................................................................... 3-1 3.4. Configuration of EUT on Test ............................................................................................. 3-2 3.5. Operating Condition of EUT ................................................................................................ 3-2 3.6. Test Procedure ...................................................................................................................... 3-2 3.7. Power Line Conducted Emission Test Results .................................................................... 3-2 4. RADIATED EMISSION TEST ...................................................................................... 4-1 4.1. Test Equipment .................................................................................................................... 4-1 4.2. Block Diagram of Test Setup ............................................................................................... 4-1 4.3. Radiated Emission Limit ...................................................................................................... 4-2 4.4. EUT Configuration on Test .................................................................................................. 4-3 4.5. Operating Condition of EUT ................................................................................................ 4-3 4.6. Test Procedure ...................................................................................................................... 4-3 4.7. Radiated Emission Test Results ........................................................................................... 4-4 5. CONDUCTED SPURIOUS EMISSIONS...................................................................... 5-1 5.1. Test Equipment .................................................................................................................... 5-1 5.2. Limit ..................................................................................................................................... 5-1 5.3. Test Procedure ...................................................................................................................... 5-1 5.4. Test result ............................................................................................................................. 5-1 6. BAND EDGE COMPLIANCE TEST ............................................................................ 6-1 6.1. Test Equipment .................................................................................................................... 6-1 6.2. Limit ..................................................................................................................................... 6-1 6.3. Test Produce ......................................................................................................................... 6-1 6.4. Test Results .......................................................................................................................... 6-1 7. 6dB Bandwidth Test ......................................................................................................... 7-1 7.1. Test Equipment .................................................................................................................... 7-1 7.2. Limit ..................................................................................................................................... 7-1 7.3. Test Procedure ......................................................................................................…

Text truncated - open the document above for the full version.

R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 12-1 12. PHOTOGRAPH OF TEST 12.1.Photos of Power Line Conducted Emission Test USB Line R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 12-2 No USB Line R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 12-1 12.2.Photos of Radiated Emission Test USB Line R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 12-2 No USB Line R AUDIX Technology (Shenzhen) Co., Ltd. page FCC ID:WWMDN4210DV1 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F11127 12-1 (Above 1000MHz) USB Line No USB Line