WZ7CAMINO-101Class B AIS Transponder

I COPYRIGHT The entire contents of this instruction manual, including any future updates, revisions, and modifications, shall remain the property of AMEC at all times. Unauthorized copies or reproduction of this manual, either in part or whole, in any form of print and electronic media, is prohibited. The contents herein can only be used for the intended purpose of this manual. DISCLAIMER AMEC is devoted to publish and maintain this product manual. As we continue to improve our AIS products to satisfy all customers‟ needs, information in this document is subject to change without notice. AMEC does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. Contact us at: Technical Support: Sales & Marketing: ALLTEK MARINE ELECTRONICS CO., LTD 7F, No. 605, Ruei-Guang Rd., Neihu, Taipei, Taiwan 114 TEL: +886 2 2627 1599 FAX: +886 2 2627 1600 www.alltekmarine.com (Your Local Dealer/Agent Warranty Stamp) Version 1.3.3 II FOR USERS IN THE UNITED STATES OF AMERICA ONLY WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. ★ The entry of static data into this device shall be performed by the vendor of the device or by an appropriately qualified person in the business of installing marine communications equipment on board vessels. ★ Instructions on how to accurately enter and confirm static data in the device can be found in Section 3.3 of this user manual. The equipment said in this manual must only be used to which it was designed. Improper operation or installation may cause damage to the equipment or injury to personnel. AMEC will not incur any liability of equipment damage or personal injury due to improper use or installation of the equipment. It is strongly recommended to read this manual and the following safety instructions before proceeding to installation or operation. WARNING! SAFETY INSTRUCTIONS ELECTRICAL SHOCK HAZARD. Do not open the case of the equipment. Only qualified personnel could work on the interior of the equipment. WARNING TURN OFF THE POWER IMMEDIATELY IF WATER LEAKS INTO THE EQUIPMENT OR OBJECT DROPS INTO THE EQUIPMENT. Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor for service. DO NOT DISASSEMBLE OR MODIFY THE EQUIPMENT. Improper disassemble or modification could cause electrical shocks, fire, or personal injury. WARNING DO NOT PLACE ANY LIQUID-FILLED CONTAINER ON TOP OF THE EQUIPMENT. Electrical shocks could be resulted if the device is contaminated with liquid. TURN OFF THE POWER IMMEDIATELY IF THE EQUIPMENT IS EMMITTING SMOKE OR FIRE. Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor for service. EVEN THOUGH THE EQUIPMENT IS WATERPROOF, PLEASE AVOID DIRECT CONTACT WITH RAIN OR SPLASHING WATER. Electrical shock or fire could be resulted if water leaks into the equipment. AVOID OPERATING THE EQUIPMENT WITH WET HANDS. Electrical shocks could be resulted if operating with wet hands. III FORWARD Congratulations on the purchase of your new CAMINO-101 Automatic Identification System (hereinafter called “AIS”). No matter where you sail now, you can have a better control of your surrounding sea, and have an enjoyable voyage. Camino-101 AIS is strictly tested to meet the rigorous demands of the marine environment. Unless improper use, installation, or maintenance, the equipment should function properly at its optimum. We thank you for choosing our product and we wish you a bon voyage. Table of Contents I. COPY RIGHT & DISCLAIMER II. WARNING & SAFETY INSTRUCTION III. FORWARD Pages 1 INTRODUCTION .................................................................................................................................. 1 1.1 CAMINO-101 Overview.............................................................................................................. 1 1.2 Type of AIS ................................................................................................................................... 2 1.3 AIS Message Type ...................................................................................................................... 2 1.4 AIS Report Rate .......................................................................................................................... 3 1.5 About this Manual ...................................................................................................................... 3 1.6 Important Notice ......................................................................................................................... 3 2 INSTALLATION .................................................................................................................................... 4 2.1 General .......................................................................................................................................... 4 2.1.1 Safety Instructions ......................................................................................................... 4 2.1.2 Unpacking and Handling the Unit............................................................................... 5 2.1.3 Items in the Package ...................................................................................................... 5 2.2 Installation Procedure ............................................................................................................... 6 2.2.1 Installation Precautions ................................................................................................ 6 2.2.2 Step by Step Installation Instructions .......................................…

Text truncated - open the document above for the full version.

Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com FCC ID: WZ7CAMINO-101 External Photos of CAMINO-101 Figure 1: Front View of CAMINO-101 Figure 2: Rear View of CAMINO-101 Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com Figure 3: Top View of CAMINO-101 Figure 4: Side View of CAMINO-101

Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com FCC ID: WZ7CAMINO-101 Type Label and Warning Label Figure 1: Type Label with FCC ID Figure 2: Type Label Location (base of unit) Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com Figure 3: Warning Label on Upper Housing (in accordance to § 80.231b) Figure 4: Warning Label on Upper Housing (room-in) Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com Figure 5: Type Label Artwork 52mm 51mm CAMINO-101 Class B AIS Transponder Power Supply: 24V DC Compass Safe Distance: 0.5M FCC ID: WZ7CAMINO-101 Serial Number: 0700 Made in Taiwan, by Alltek Marine Electronics Corp. 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492

Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com FCC ID: WZ7CAMINO-101 Internal Photos of CAMINO-101 Figure 1: Top View of Internal CAMINO-101 Figure 2: Internal View with CPU Module removed Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com Figure 3: Top View of CPU Module Figure 4: Bottom View of CPU Module Alltek Marine Electronics Corp. ◆ 7F, No.605, Ruei-Guang Rd., Neihu, Taipei, Taiwan, 11492 ◆ www.alltekmarine.com Figure 5: Top View of RF Module Figure 6: Bottom View of RF Module

I COPYRIGHT The entire contents of this instruction manual, including any future updates, revisions, and modifications, shall remain the property of AMEC at all times. Unauthorized copies or reproduction of this manual, either in part or whole, in any form of print and electronic media, is prohibited. The contents herein can only be used for the intended purpose of this manual. DISCLAIMER AMEC is devoted to publish and maintain this product manual. As we continue to improve our AIS products to satisfy all customers‟ needs, information in this document is subject to change without notice. AMEC does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. Contact us at: Technical Support: Sales & Marketing: ALLTEK MARINE ELECTRONICS CO., LTD 7F, No. 605, Ruei-Guang Rd., Neihu, Taipei, Taiwan 114 TEL: +886 2 2627 1599 FAX: +886 2 2627 1600 www.alltekmarine.com (Your Local Dealer/Agent Warranty Stamp) Version 1.3.3 II FOR USERS IN THE UNITED STATES OF AMERICA ONLY WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. ★ The entry of static data into this device shall be performed by the vendor of the device or by an appropriately qualified person in the business of installing marine communications equipment on board vessels. ★ Instructions on how to accurately enter and confirm static data in the device can be found in Section 3.3 of this user manual. The equipment said in this manual must only be used to which it was designed. Improper operation or installation may cause damage to the equipment or injury to personnel. AMEC will not incur any liability of equipment damage or personal injury due to improper use or installation of the equipment. It is strongly recommended to read this manual and the following safety instructions before proceeding to installation or operation. WARNING! SAFETY INSTRUCTIONS ELECTRICAL SHOCK HAZARD. Do not open the case of the equipment. Only qualified personnel could work on the interior of the equipment. WARNING TURN OFF THE POWER IMMEDIATELY IF WATER LEAKS INTO THE EQUIPMENT OR OBJECT DROPS INTO THE EQUIPMENT. Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor for service. DO NOT DISASSEMBLE OR MODIFY THE EQUIPMENT. Improper disassemble or modification could cause electrical shocks, fire, or personal injury. WARNING DO NOT PLACE ANY LIQUID-FILLED CONTAINER ON TOP OF THE EQUIPMENT. Electrical shocks could be resulted if the device is contaminated with liquid. TURN OFF THE POWER IMMEDIATELY IF THE EQUIPMENT IS EMMITTING SMOKE OR FIRE. Continue operating the equipment could cause electrical shock or fire. Contact your nearest distributor for service. EVEN THOUGH THE EQUIPMENT IS WATERPROOF, PLEASE AVOID DIRECT CONTACT WITH RAIN OR SPLASHING WATER. Electrical shock or fire could be resulted if water leaks into the equipment. AVOID OPERATING THE EQUIPMENT WITH WET HANDS. Electrical shocks could be resulted if operating with wet hands. III FORWARD Congratulations on the purchase of your new CAMINO-101 Automatic Identification System (hereinafter called “AIS”). No matter where you sail now, you can have a better control of your surrounding sea, and have an enjoyable voyage. Camino-101 AIS is strictly tested to meet the rigorous demands of the marine environment. Unless improper use, installation, or maintenance, the equipment should function properly at its optimum. We thank you for choosing our product and we wish you a bon voyage. Table of Contents I. COPY RIGHT & DISCLAIMER II. WARNING & SAFETY INSTRUCTION III. FORWARD Pages 1 INTRODUCTION .................................................................................................................................. 1 1.1 CAMINO-101 Overview.............................................................................................................. 1 1.2 Type of AIS ................................................................................................................................... 2 1.3 AIS Message Type ...................................................................................................................... 2 1.4 AIS Report Rate .......................................................................................................................... 3 1.5 About this Manual ...................................................................................................................... 3 1.6 Important Notice ......................................................................................................................... 3 2 INSTALLATION .................................................................................................................................... 4 2.1 General .......................................................................................................................................... 4 2.1.1 Safety Instructions ......................................................................................................... 4 2.1.2 Unpacking and Handling the Unit............................................................................... 5 2.1.3 Items in the Package ...................................................................................................... 5 2.2 Installation Procedure ............................................................................................................... 6 2.2.1 Installation Precautions ................................................................................................ 6 2.2.2 Step by Step Installation Instructions .......................................…

Text truncated - open the document above for the full version.

Bundesamt für Seeschifffahrt und Hydrographie Federal Maritime and Hydrographic Agency Test Report No.. BSH/46162/4321297/10-1Date: 07.06.2010page 2 of 112 Bundesamt für Seeschifffahrt und Hydrographie Federal Maritime and Hydrographic Agency Test Report No.. BSH/46162/4321297/10-1Date: 07.06.2010page 3 of 112 General Applicant:Alltek Marine Electronics Corp. 9F-1, No.360, Ruei Guang Rd., Neihu, Taipei, Taiwan, R.O.C. Equipment under test: Type:Camino 101 Manufacturer: Alltek Marine Electronics Corp. 9F-1, No.360, Ruei Guang Rd., Neihu, Taipei, Taiwan, R.O.C. Place of test:BSH test laboratory Hamburg, Room 916 Start of test:19 October 2009 End of test:27 May 2010 Test standards 1 : IEC 62287-1 Maritime navigation and radiocommunication equipment and systems- Automatic Identification Systems Class B shipborne equipment of the Universal Automatic Identification System (AIS) using CSTMA techniques Summary Test No. ReferenceSectionResult (passed/ not passed / not applicable / not tested) 2 IEC 62287-1 10 Operational testsPassed 3 IEC 62287-1 11 Physical testsNot included 4 IEC 62287-1 12 Specific tests of link layerPassed 5 IEC 62287-1 13 Specific tests of network layerPassed 6 IEC 62287-1 C.3 DSC functionality testsPassed 1 Numbers listed in the titles of the test sections of this report refer to the respective sections of IEC 61993-2 if not stated otherwise. Bundesamt für Seeschifffahrt und Hydrographie Federal Maritime and Hydrographic Agency Test Report No.. BSH/46162/4321297/10-1Date: 07.06.2010page 4 of 112 GENERAL......................................................................................................................................................................3 SUMMARY ....................................................................................................................................................................3 1GENERAL INFORMATION ............................................................................................................................7 1.1EQUIPMENT HISTORY.........................................................................................................................................7 1.1.1EUT system no 1......................................................................................................................................7 1.1.2EUT system no 2......................................................................................................................................8 1.1.3EUT system no 3......................................................................................................................................8 1.1.4EUT system no 4......................................................................................................................................9 1.1.5EUT system no 5......................................................................................................................................9 1.2T EST ENVIRONMENT........................................................................................................................................10 1.2.1Test environment no 1 ...........................................................................................................................10 1.3COMPOSITION..................................................................................................................................................11 1.4L EGEND............................................................................................................................................................12 1.5TEST NOTES......................................................................................................................................................12 1.5.1General problems..................................................................................................................................13 24. GENERAL REQUIREMENTS ..................................................................................................................14 2.14.2 M ANUALS.................................................................................................................................................14 2.24.3 MARKING AND IDENTIFICATION..............................................................................................................15 310 OPERATIONAL TESTS ..........................................................................................................................17 3.110.2 MODES OF OPERATING...........................................................................................................................17 3.1.110.2.1 Autonomous mode ....................................................................................................................17 3.1.1.110.2.1.1 Transmit Position reports................................................................................................................... 17 3.1.1.210.2.1.2 Receive Class A position reports .......................................................................................................18 3.1.1.310.2.1.3 Receive Class B”CS” position reports................................................................................................ 19 3.1.1.410.2.1.4 Receive in adjacent time periods .......................................................................................................20 3.1.1.510.2.1.5 Rx performance test ........................................................................................................................... 22 3.1.210.2.2 Assigned mode.........................................................................................................................23 3.1.2.110.2.2.1 Group assignment .............................................................................................................................. 23 3.1.2.210.2.2.2 Base station reservations...............................…

Text truncated - open the document above for the full version.

Königswinkel 10 32825 Blomberg Germany Phone+49 5235 9500 0 Fax+49 5235 9500 10 TEST REPORT on IEC 62287-1: Edition 1.0(2006-03) MaritimeNavigation and RadiocommunicationEquipment andSystems: Class Bshipborne equipment of the Automatic Identification System(AIS) Part 1: Carrier sense division multiple access (CSTDMA) techniques Test Report Reference: F092025E3 Equipment under Test: AMEC Camino-101 Class B AIS Serial Number:- Applicant:AlltekMarine Electronics Corp. Manufacturer:Alltek Marine Electronics Corp. TEST REPORT REFERENCE: F092025E3 Examiner: Raimund BLASKDate of issue: 11 February 2010page2 of50 1 IDENTIFICATION.....................................................................................................................................3 1.1 APPLICANT.....................................................................................................................................3 1.2 MANUFACTURER..........................................................................................................................3 1.3 DATES.............................................................................................................................................3 1.4 TEST LABORATORY......................................................................................................................4 1.5 RESERVATION...............................................................................................................................4 1.6 REFERENCES................................................................................................................................4 2 TECHNICAL DATA OFEQUIPMENT......................................................................................................5 3 ADDITIONAL INFORMATION..................................................................................................................6 4 TEST OVERVIEW.................................................................................................................................... 7 5 TRANSMITTER REQUIREMENTS..........................................................................................................8 5.1 FREQUENCY ERRORSUBCLAUSE 11.1.1................................................................................9 5.2 CARRIER POWER (CONDUCTED)SUBCLAUSE 11.1.2...........................................................10 5.3 MODULATION SPECTRUM 25 KHZ CHANNEL MODESUBCLAUSE 11.1.3............................11 5.4 TRANSMITTER TESTSEQUENCE AND MODULATION ACCURACY SUBCLAUSE 11.1.4.....13 5.5 TRANSMITTER OUTPUT POWER VERSUS TIMEFUNCTION SUBCLAUSE11.1.5.................16 6 RECEIVER REQUIREMENTS.................................................................................................................19 6.1 TDMA-RECEIVER SENSITIVITYSUBCLAUSE 11.2.1................................................................20 6.2 ERROR BEHAVIOURAT HIGH INPUT LEVELSSUBCLAUSE 11.2.2.......................................21 6.3 CO-CHANNEL REJECTIONSUBCLAUSE 11.2.3.......................................................................22 6.4 ADJACENT CHANNELSELECTIVITYSUBCLAUSE 11.2.4........................................................23 6.5 SPURIOUS RESPONSE REJECTIONSUBCLAUSE 11.2.5........................................................24 6.6 INTERMODULATIONRESPONSE REJECTIONSUBCLAUSE 11.2.6.......................................26 6.7 BLOCKING OR DESENSITISATIONSUBCLAUSE 11.2.7..........................................................27 6.8 SPURIOUS EMISSIONS FROM THE RECEIVERSUBCLAUSE 11.3.1......................................29 6.9 SPURIOUS EMISSIONS FROM THE TRANSMITTERSUBCLAUSE 11.3.2..............................32 6.10 MAXIMUM SENSITIVITY SUBCLAUSE C.4...............................................................................38 6.11 ERROR BEHAVIOURAT HIGH INPUT LEVELS SUBCLAUSE C.4.2.......................................39 6.12 CO-CHANNEL REJECTIONSUBCLAUSE C.4.3.......................................................................40 6.13 ADJACENT CHANNEL SENSITIVITYSUBCLAUSE C.4.4........................................................41 6.14 SPURIOUS RESPONSE REJECTIONSUBCLAUSE C.4.5.......................................................42 6.15 INTERMODULATIONRESPONSE REJECTIONSUBCLAUSE C.4.6.......................................43 6.16BLOCKING OR DESENSITISATIONSUBCLAUSE C.4.7..........................................................44 7 TEST EQUIPMENT..................................................................................................................................45 8 LIST OF ANNEXES..................................................................................................................................50 TEST REPORT REFERENCE: F092025E3 Examiner: Raimund BLASKDate of issue: 11 February 2010page3 of50 1 IDENTIFICATION 1.1APPLICANT Name:Alltek Marine Electronics Corp. Address:9F-1, No. 360, Ruei Guang Rd., Neihu 114 Taipei Country:Taiwan Name for contact purposes:Mr. Leo Hsieh Tel:+886-(02)-2627-1599ext.133 Fax:+886-(02)-2627-1600 e-mail address:[email protected] 1.2MANUFACTURER Name:Alltek Marine Electronics Corp. Address:9F-1, No. 360, Ruei Guang Rd., Neihu 114 Taipei Country:Taiwan Name for contact purposes:Mr. Leo Hsieh Tel:+886-(02(-2627-5859 ext. 35 Fax:+886-(02(-2627-5859 e-mail address:[email protected] 1.3DATES Date of Receipt of Test Sample:10August 2009 Start of test:12August 2009 Finish of test:20 November 2009 TEST REPORT REFERENCE: F092025E3 Examiner: Raimund BLASKDate of issue: 11 February 2010page4 of50 1.4TEST LABORATORY The tests were carried out at:PHOENIXTESTLAB GmbH Königswinkel 10 D-32825 BlombergTel:+49 (0) 5235 / 95 00-0 GermanyFax:+49 (0) 52 35 / 95 00-10 Test engineer:Raimund BLASK15 February 2010 NameDate Test report checked by:Bernd STEINER16 February 2010 NameDate Stamp 1.5RESERVATION T h i s te s t r e p o r t i s o n l y v a l i d i n t h e o r i g i n a l f o r m…

Text truncated - open the document above for the full version.

Report No. 103371R-RFCEP03V01 Page: 1 of 37 Test Report Product Name CAMINO-101 Class B AIS Transponder Model No. CAMINO-101 Applicant Alltek Marine Electronics Corp. Address 7F, No.605, Ruei Guang Rd., Neihu, Taipei, Taiwan, 114 R.O.C. Date of Receipt Sep. 29, 2009 Issued Date Apr. 15, 2010 Report No. 103371R-RFCEP03V01 Report Version V1.0 The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No. 103371R-RFCEP03V01 Page: 2 of 37 Test Report Certification Issued Date: Apr. 15, 2010 Report No.: 103371R-RFCEP03V01 Product Name CAMINO-101 Class B AIS Transponder Applicant Alltek Marine Electronics Corp. Address 7F, No.605, Ruei Guang Rd., Neihu, Taipei, Taiwan, 114 R.O.C. Manufacturer Alltek Marine Electronics Corp. Model No. CAMINO-101 EUT Rated Voltage DC 10~28V EUT Test Voltage DC 24V Trade Name AMEC Applicable Standard ETSI EN 301 843-1:V1.2.1 (2004.06) ETSI EN 301 843-2:V1.2.1 (2004.06) Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : (Adm. Specialist / Leven Huang ) Tested By : (Engineer / Johnson Liao) Approved By : ( Manager / Vincent Lin ) Accredited by DNV, Nemko and NIST (NVLAP) Report No. 103371R-RFCEP03V01 Page: 3 of 37 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Tested System Details....................................................................................................................6 1.3. Configuration of tested System .....................................................................................................7 1.4. EUT Exercise Software .................................................................................................................7 1.5. Test Facility ...................................................................................................................................8 2. Conducted Emission....................................................................................................................9 2.1. Test Equipmen ...............................................................................................................................9 2.2. Test Setup ......................................................................................................................................9 2.3. Limits ..........................................................................................................................................10 2.4. Test Procedure .............................................................................................................................10 2.5. Test Specification ........................................................................................................................11 2.6. Uncertainty ..................................................................................................................................11 2.7. Test Result ...................................................................................................................................11 3. Radiated Emission .....................................................................................................................12 3.1. Test Equipment............................................................................................................................12 3.2. Test Setup ....................................................................................................................................12 3.3. Limits ..........................................................................................................................................13 3.4. Test Procedure ..........…

Text truncated - open the document above for the full version.