X4K-UWPEB01Universal PE (Photo Electric) Beam Kit - PE Beam Transmitter

Wireless First Safety Beam Kit INSTRUCTION MANUAL Doc #:160963_03. March 3, 2026 Part#: 102050 The Wireless First Safety Beam Kit is an infrared safety system for automatic doors and gates. It supports wired and wireless connection and control with compatible door operators, helping prevent accidents by detecting movement or obstacles. 1L BRACKET ASSEMBLY X 2 2TRANSMITTER / RECEIVER ASSEMBLY X 2 3WIRELESS BASE STATION X 1 4AA SIZE ALKALINE BATTERIES X 4 5WIRELESS BASE STATION HARNESS X 1 6SELF ADHESIVE HOOK & LOOP STRIP FOR WIRELESS BASE S TAT I O N X 1 KIT CONTENTS 1 1 2 2 34 5 6 2 WIRELESS FIRST SAFETY BEAM — INSTRUCTION SHEET IMPORTANT SAFETY INSTRUCTIONS SAFETY OVERVIEW READ AND SAVE THESE INSTRUCTIONS Installation and servicing must be performed by trained personnel and comply with: • UL 325 / ANSI/CAN/UL 325 (USA/Canada), • AS/NZS 60335.2.103 (Australia/New Zealand), • local electrical codes (NEC Article 725 Class 2 / CEC), and • applicable gate standards (e.g., ASTM F2200 for vehicular gates) WARNING ENTRAPMENT PROTECTION: • Mount the beam no higher than 150 mm (6 in) above the floor and within 150 mm (6 in) of the door travel path (perpendicular). • Test operation at installation and monthly thereafter. • Do not operate if the beam fails to stop/reverse movement when interrupted. WIRELESS MODE • Use wireless mode only where RF communication is reliable; switch to wired mode if interference is suspected. 3 WIRELESS FIRST SAFETY BEAM — INSTRUCTION SHEET TRANSMITTERS COMPLIANCE S TAT E M E N T This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with the FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. In order to comply with FCC and ISED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your local dealer or an experienced radio/TV technician for help. WARNING: Any changes or modifications not expressively approved by the grantee could void the user’s authority to operate this equipment.. 4 WIRELESS FIRST SAFETY BEAM — INSTRUCTION SHEET DÉCLARATION DE CONFORMITÉ DE L’ÉMETTEUR L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage ; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Cet équipement est conforme aux limites d’exposition aux radiations de la FCC et d’ISED Canada établies pour un environnement non contrôlé. Afin de se conformer aux exigences d’exposition RF ISED, cet appareil doit être installé pour fournir au moins 20 cm de séparation du corps humain en tout temps. REMARQUE: Cet équipement a été testé et déclaré conforme aux limites applicables à un appareil numérique de classe B, conformément à la partie 15 des règles de la FCC. Ces limites visent à assurer une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l’énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions, peut causer des interférences nuisibles aux communications radio. Cependant, il n’est pas garanti qu’aucune interférence ne se produira dans une installation particulière. Si cet équipement cause des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en éteignant puis en rallumant l’équipement, l’utilisateur est encouragé à essayer de corriger l’interférence par une ou plusieurs des mesures suivantes : • Réorienter ou déplacer l’antenne de réception. • Augmenter la distance entre l’équipement et le récepteur. • Brancher l’équipement sur une prise d’un circuit différent de celui auquel le récepteur est connecté. • Consulter votre revendeur local ou un technicien radio/TV expérimenté pour obtenir de l’aide. AVERTISSEMENT: Tout changement ou toute modification non expressément approuvé par le bénéficiaire peut annuler le droit de l’utilisateur à utiliser cet équipement. 5 WIRELESS FIRST SAFETY BEAM — INSTRUCTION SHEET WIRELESS Wireless Protocol Bluetooth - BLE Maximum Wireless Range 59’ (18m) Maximum Door Width 27’10” / 8.5m (wireless) 32’9” / 10m (wired) Power Source Base StationPowered by Operator Receiver, Transmitter 2 x 1.5V AA Size E91 Alkaline Battery per unit (4 total). Battery life4yrs* Environmental Rating IP66 Operating temperature −20°…

Text truncated - open the document above for the full version.

Page 1 of 4 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex A: External - EUT Photographs Automatic Technology Australia Pty Ltd PEBTX01-1.02 Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter REPORT: E2512-1918-9 Annex A DATE: January, 2026 EMC Bayswater Test Report E2512-1918-9 Annex A Page 2 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – External views 2 3 4 5 6 7 8 9 EMC Bayswater Test Report E2512-1918-9 Annex A Page 3 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2512-1918-9 Annex A Page 4 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9

Page 1 of 3 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex C: Test Configuration Photographs Automatic Technology Australia Pty Ltd PEBTX01-1.02 Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter REPORT: E2512-1918-9 Annex C DATE: January, 2026 EMC Bayswater Test Report E2512-1918-9 Annex C Page 2 of 3 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 Radiated measurements – EUT Y Orientation 2 Radiated measurements – 9kHz to 30MHz – X Antenna orientation 3 Radiated measurements – 9kHz to 30MHz – Y Antenna orientation 4 Radiated measurements – 9kHz to 30MHz – Z Antenna orientation 5 Radiated measurements – below 1GHz 6 Radiated measurements – above 1GHz EMC Bayswater Test Report E2512-1918-9 Annex C Page 3 of 3 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6

Page 1 of 86 EMC Bayswater Pty Ltd EMC ENGINEERS & LABORATORIES 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 RADIO COMPLIANCE REPORT Certification Test Report In accordance with: CFR47 FCC Part 15, Subpart C, 15.247 Automatic Technology Australia Pty Ltd PEBTX01-1.02 Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter FCC ID: X4K-UWPEB01 REPORT: E2512-1918-9 DATE: January, 2026 Accreditation Number: 18553 Accredited for compliance with ISO/IEC 17025 - Testing The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. EMC Bayswater Test Report E2512-1918-9 Page 2 of 86 Prepared & tested by: Approved by: 27/01/2026 11:16 Adnan Zaman (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Certificate of Compliance Certification Compliance Report EMC Bayswater Test Report: E2512-1918-9 Issue Date: January, 2026 Test Sample(s): Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter Model No: PEBTX01-1.02 Serial No: Not stated FCC ID: X4K-UWPEB01 Variant: PEBRX01-1.02 The above listed model (PEBTX01-1.02) was tested by EMC Bayswater Pty Ltd as a representative sample and the results and conclusions within this report do not necessarily reflect compliance for other variants. Please refer to section 5 of this report for variant information and the customer variant declaration. Customer Details: Mr. Nikolai Klepikov Automatic Technology Australia Pty Ltd 6-8 Fiveways Boulevard, Keysborough, Victoria 3148 Australia Phone No: +61 3 9791 0275 e-mail: [email protected] Test Specification: CFR47 FCC Part 15, Subpart C, 15.247 Results Summary: 15.203 - Antenna requirement Complied 15.247 (a)(2) - 6dB Bandwidth Complied 15.247 (b)(3) - Maximum Output Power Complied 15.247 (d) - Out-of-Band Emissions - – 100kHz, -20dBc Complied 15.247 (d) - Emissions on the Band edge Complied 15.247 (d), 15.209 - Radiated emissions in Restricted bands Complied 15.247 (e) - Power Spectral Density Complied 15.247 (i) - Radio frequency hazard Complied Test Date(s): 11 th to 17 th of December, 2025 Test House (Issued By): EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria 3136 Australia FCC Accredited Test Firm Registration number: 527798 FCC Accredited Test Firm Designation number: AU0004 Phone No: +61 3 9761 5888 e-mail: [email protected] Fax No: +61 3 8761 6547 Web: www.emcbayswater.com.au/ This is to certify that the necessary measurements were made by EMC Bayswater Pty Ltd, and that the Automatic Technology Australia Pty Ltd, PEBTX01-1.02, Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter, has been tested in accordance with requirements contained in the appropriate commission regulations. EMC Bayswater Test Report E2512-1918-9 Page 3 of 86 Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Radio Compliance Report for Automatic Technology Australia Pty Ltd Contents 1. Introduction ................................................................................................................... 5 2. Test Report Revision History ........................................................................................ 5 3. Report Information ........................................................................................................ 5 4. Summary of Results ...................................................................................................... 5 5. Product Sample Details ................................................................................................. 6 5.1. EUT Description........................................................................................................ 6 5.2. Product description ................................................................................................... 6 5.3. Support Equipment ................................................................................................... 6 5.4. Product operating modes .......................................................................................... 7 5.5. Product operating mode for testing ........................................................................... 7 5.6. Configuration ............................................................................................................ 7 5.7. Modifications ............................................................................................................. 7 6. Test Facility & Equipment ............................................................................................. 7 6.1. Test Facility .............................................................................................................. 7 6.2. Test Equipment ........…

Text truncated - open the document above for the full version.

Autom atic Technology (Australia) Pty Ltd 6- 8 Fiveways Boulevard, Keysborough, VIC 3173 T +61 3 9791 0200 F +61 3 9791 0250 www.ata-aust.com.au ABN : 11 007 125 368 Date: 13/01/2026 Antenna information 1.Antenna v iew. 2.Antenna type. PCB L-type Antenna-2. 3.Antenna parameters. Frequenc y f₀ = 2.44 GHz Operating frequency range: 2.402 GHz to 2.85 GHz Antenna gain*: from -1 dBi to 0.5 dBi Input return loss at 2.44 GHz: from -5 dB *Antenna gain information is not required as compliance details were measured in radiated mode and therefore antenna characteris tics are inherent to the measurement gain.

Page 1 of 7 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 RF Radiation Exposure Evaluation In accordance with: FCC KDB 447498 D01 v06 Automatic Technology Australia Pty Ltd PEBTX01-1.02 Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter FCC ID: X4K-UWPEB01 REPORT: E2512-1918-10 DATE: January, 2026 EMC Bayswater Test Report E2512-1918-10 Page 2 of 7 Prepared by: Approved by: 27/01/2026 10:57 Adnan Zaman (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. RF Radiation Exposure Evaluation Report EMC Bayswater Test Report: E2512-1918-10 Issue Date: January, 2026 Product: Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter Model No: PEBTX01-1.02 Serial No: Not stated FCC ID: X4K-UWPEB01 Variant: PEBRX01-1.02 The above listed model (PEBTX01-1.02) was tested by EMC Bayswater Pty Ltd as a representative sample and the results and conclusions within this report do not necessarily reflect compliance for other variants. Please refer to section 5 of this report for variant information. Customer Details: Mr. Nikolai Klepikov Automatic Technology Australia Pty Ltd 6-8 Fiveways Boulevard, Keysborough, Victoria 3148, Australia Phone No: +61 3 9791 0275 e-mail: [email protected] Standard(s): FCC KDB 447498 D01 v06 RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES CFR47 FCC Part 2, Subpart J, 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. CFR47 FCC Part 2, Subpart J, 2.1093 Radiofrequency radiation exposure evaluation: portable devices. Results Summary: RF Radiation exposure requirements Complied Test Date(s): 17 th of December, 2025 Test House (Issued By): EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria, 3136, Australia FCC Accredited Test Firm Registration number: 527798 FCC Accredited Test Firm Designation number: AU0004 Phone No: +61 3 9761 5888 Email: [email protected] Fax: +61 3 8761 6547 Web: www.emcbayswater.com.au The Automatic Technology Australia Pty Ltd, PEBTX01-1.02, Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter, measured EIRP is below the SAR exception threshold (5mm distance) and the calculated power density level at a distance of 20cm are below the maximum levels allowed by regulations therefore complied with the requirements of CFR47 FCC Part 2, Subpart J, 2.1093. This is to certify that the necessary evaluations were made by EMC Bayswater Pty Ltd, and that the Automatic Technology Australia Pty Ltd, PEBTX01-1.02, Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter, has been tested in accordance with requirements contained in the appropriate commission regulations. EMC Bayswater Test Report E2512-1918-10 Page 3 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. RF Radiation Exposure Evaluation for Automatic Technology Australia Pty Ltd Contents 1. Introduction ................................................................................................................... 4 2. Test Report Revision History ........................................................................................ 4 3. Report Information ........................................................................................................ 4 4. Product Details .............................................................................................................. 5 4.1. Product Sample Details ........................................................................................... 5 4.2. Product description .................................................................................................. 5 5. SAR and RF Exposure exception evaluation ............................................................... 6 5.1. SAR exception evaluation ........................................................................................ 6 5.2. RF Exposure Evaluation (MPE) ............................................................................... 7 6. Conclusion ..................................................................................................................... 7 EMC Bayswater Test Report E2512-1918-10 Page 4 of 7 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. 1. Introduction RF Radiation Exposure evaluation was performed on an Automatic Technology Australia Pty Ltd, PEBTX01-1.02, Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter in accordance with FCC KDB 447498 D01 v06. 2. Test Report Revision History None 3. Report Information EMC Bayswater Pty Ltd reports apply only to the specific samples tested under the stated test conditions. All samples tested were in good operating condition throughout the entire test program unless otherwise stated. EMC Bayswater Pty Ltd does not in any way guarantees the later performance of the product/equipment. It is the manufacturer's responsibility to ensure that additional production units of the tested model are manufactured with identical electrical and mechanical components. EMC Bayswater Pty Ltd shall have no liability for any deductions, inference or generalisations drawn by the clients or others from EMC Bayswater Pty Ltd issued reports. This report shall not be used to claim, constitute or imply product endorsement by EMC Bayswater Pty Ltd. This report shall not be reproduced except in full, without the written approval of EMC Bayswater Pty Ltd. This document may be altered or revised by EMC Bayswater Pty Ltd personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by EMC Bayswater Pty Ltd will nullify the document. E…

Text truncated - open the document above for the full version.

Page 1 of 5 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex B: Internal - EUT Photographs Automatic Technology Australia Pty Ltd PEBTX01-1.02 Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter REPORT: E2512-1918-9 Annex B DATE: January, 2026 EMC Bayswater Test Report E2512-1918-9 Annex B Page 2 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – Internal views 2 3 4 5 6 7 8 9 10 11 12 13 14 15 EMC Bayswater Test Report E2512-1918-9 Annex B Page 3 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2512-1918-9 Annex B Page 4 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10 Photograph 11 Photograph 12 EMC Bayswater Test Report E2512-1918-9 Annex B Page 5 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 13 Photograph 14 Photograph 15

Antenna placement

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 29, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: X4K-UWPEB01 Nikolai Klepikov of Automatic Technology (Australia) Pty ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as a specifically named entity or any of its subsidiaries or affiliates as an entity producing “covered” equipment. Regards, Nikolai Klepikov Senior Electronics Design Engineer

Federal Communications Commission Authorization and Evaluation Division Date: January 29, 2026 Subject: FCC Application for FCC ID: X4K-UWPEB01 - Confidentiality Request. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram CONF_UPE-1V1_Blkdia.pdf Schematics 1 Schematics 2 CONF_PEBTX01-1.02_Schem.pdf CONF_PEBRX01-1.02_Schem.pdf Operational Description CONF_UPE-1V1_OpDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Nikolai Klepikov Senior Electronics Design Engineer

EMC Technologies Pty. Ltd. ABN 82 057 105 549 Melbourne 176 Harrick Road Keilor Park, Vic 3042 Tel: +61 3 9365 1000 Sydney Unit 3/87 Station Road Seven Hills, NSW 2147 Tel: +61 2 9624 2777 Email: [email protected] Web: www.emctech.com.au EMC Technologies Pty Ltd, 176 Harrick Road, Keilor Park VIC 3042 Australia www.emctech.com.au To Federal Communications Commission Attention: Certification Officer EMCT Ref: M2602003 Date: February 4, 2026 Subject: Automatic Technology Australia original filing (FCC ID:X4K-UWPEB01) Product Name: Universal PE (Photo Electric) Beam Kit – PE Beam Transmitter Model (tested): PEBTX01-1.02 Variant Model: PEBRX01-1.02 FCC ID: FCC ID:X4K-UWPEB01 Radio: Bluetooth Low Energy – N52832 (Mfr. Nordic Semiconductor), 2402-2480 MHz Antenna: PCB Antenna, 0.5 dBi gain. Description: (supplied by manufacturer) Detection of any objects in the garage doorway. Works with garage door or gate operators B&D and Automatic Technology. PE Beam Transmitter of the Universal PE (Photo Electric) Beam Kit. Please Note: Product Variants: Application is for FCC certification of PEBTX01-1.02 and product variant: PEBRX01- 1.02. Please refer to Test Report E2512-1918-9.pdf (appendix D) ATA Variant Declaration.pdf Variant files: Internal and External photos, Label and User manual Please refer to: • PEBRX01-1.02 Photos_External.pdf, • PEBRX01-1.02 Photos_Internal.pdf, • PEBRX01-1.02 LABEL IDENTITY UWPE-1V1 RX.pdf • PEBRX01-1.02 is included in document: Manual - 160963_01 Wireless First Safety Beam Kit Instruction Sheet.pdf FCC 15.19 statement: This application includes a request to leave the FCC 15.19 statement from the device (PTX10V1AM, PTX10V1SM). Please refer to FCC Label request_Exclusion of 15.19 compliance statement from device UWPEB01.pdf. Permanent Confidentiality: Application includes request for permanent confidentiality – Schematics. Block Diagram, Operational Description Agent: EMC Technologies is acting as agent for Automatic Technologies Australia in this application. Regards _____________ Ian Paul Ng Senior Test Engineer EMC Technologies Pty Ltd 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: +61 3 9365 1000 www.emctech.com.au

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 4, 2026 Subject: FCC Application for FCC ID: X4K-UWPEB01 To Whom It May Concern: As per KDB 784748, Appendix A section A.2, we, the undersigned, hereby request permission to exclude the FCC 15.19 compliance statement from our device. The devices (PEBTX01-1.02 and PEBRX01-1.02) are extremely small (93x62x45mm) and does not utilize electronic labelling. The FCC 15.19 compliance statement will be placed in the user manual. Sincerely, Nikolai Klepikov Senior Electronics Design Engineer

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 29, 2026 SUBJECT: FCC Application for FCC ID: X4K- UWPEB01 To Whom It May Concern: Nikolai Klepikov of Automatic Technology (Australia) Pty Ltd (“the applicant”), hereby authorize Ian Paul Ng at EMC Technologies Pty Ltd to act on our behalf, to apply to the Federal Communications Commission for FCC approval of our equipment. Any and all acts carried out by Ian Paul Ng at EMC Technologies on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Nikolai Klepikov Senior Electronics Design Engineer

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 9, 2026 SUBJECT: FCC Application for Family Certification IC: X4K-UWPEB01 To Whom It May Concern: As per FCC requirements, Automatic Technology (Australia) Pty Ltd requests a Family Certification for the following: Tested sample: PMN: Wireless First Safety Beam Kit HVIN (model): PEBTX01-1.02 Non-RF boards and circuitry: The PEBTX01-1.02 board is equipped with an IR transmitter SFH4545DW. RF boards and circuitry: The PEBTX01-1.02 board features an RF TxRx+ MCU, Bluetooth v5.3, 2.4GHz frequency, 512KB Flash, 64KB RAM, and 48 VFQFN pads. Exterior casing and colour: UPE-1V1-PEB Enclosure Kit (Black) Changes/differences to the certified device: Variant 1: PMN: Wireless First Safety Beam Kit HVIN (model): PEBRX01-1.02 Non-RF boards, and circuitry differences: The PEBRX01-1.02 board is equipped with an IR receiver TSSP96038TR RF boards, and circuitry differences: No differences to the RF part and circuitry Exterior casing and colour differences: UPE-1V1-PEB Enclosure Kit (Black) Sincerely, Nikolai Klepikov Senior Electronics Design Engineer

Federal Communications Commission Authorization and Evaluation Division Date: 02/03/2026 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: X4K-UWPEB01 Automatic Technology (Australia) Pty Ltd (“the applicant”) certifies that, as of the date of the filing of the application, Automatic Technology America LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Automatic Technology (Australia) Pty Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. Automatic Technology America LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Automatic Technology America LLC Address: 28610 Hwy 290 - Suite F09-345, Cypress, TX 77433 Contact person: Corrado Boschetto Tel: (737) 262-5035 E-mail:corrado.boschetto@automatictechnol…

Text truncated - open the document above for the full version.