X4K-WPTX5V102BWall Control

FOR LIGHT-DUTY COMMERCIAL DOOR USE ONLY Doc # 160402_00 Part # 87035 Released 10/05/19 Light-duty Commercial Rolling Door Opener DOMINATOR EasyRoller ® Instruction Manual (Instruction d’Installation) 4008033 Conforms to UL 325 Certified to CSA C22.2 No.247 WARNING!: It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference. ELECTROCUTION!: To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. This operator is not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. AVERTISSEMENT! pour la sécurité des usagers, il est essentiel de suivre toutes les instructions. Le non- respect des instructions d’installation et des avertissements de sécurité peut causer de graves blessures et/ou endommager l’appareil et la télécommande. Conservez ces instructions en lieu sûr. AVERTISSEMENT ! Pour réduire les risques d'électrocution, cet appareil est équipé d’une fiche avec broche de mise à la terre. Cette fiche ne peut être branchée que dans une prise avec mise à la terre. S’il n’est pas possible de la brancher dans la prise, faites poser une prise appropriée par un électricien qualifié. Ne pas modifier la fiche. Ce matériel est pas équipé pour le câblage permanent. En l'absence de réceptacle approprié, contactez un électricien qualifié pour en installer un. Diamond PD Power Drive : Instruction Manual Dominator EasyRoller Instruction Manual 3 © Copyright 2018 CONTENTS Rolling Garage Door Operator 1. Safety Informati on 4 2. System Specifications 6 3. Kit Contents 7 4. Setup Requirements 7 4.1 Tools Required 7 4.2 The Opener: 8 4.3 Unsuitable Door Types 8 4.4 Sideroom 8 5. Operator Safety & Security 9 5.1 Your Door CAN NOT be used by t he opener when: 9 5.2 Your Door CAN be used when: 9 5.3 To Disengage the Opener: 9 5.4 To Re-Engage the Opener: 9 6. Installati on Instructions 10 6.1. Door Preparation 11 6.2. Fit the Weight Bar 11 6.2.1 If the door has a handle: 11 6.2.2 I f the door does not have a handle: 11 6.3. Pinning the Door 12 6.4 Proping the Door 12 6.5. Mounting the Opener 13 6.5.1 Raising the Door: 13 6.5.2 Mounting the Opener: 13 6.6 Safety Beam Installation 14 6.6.1 Safety Infra-Red Beam Kit (P/N 62047) 14 6.6.2 Assembling the Mounting Bracket 14 6.6.3 PE Assist Alignment 14 6.7. Setting the Travel Limits 15 6.7.1 Initial Preparation: 15 6.7.2 Set the Limit Positions: 15 6.7.3 Resetting the Door Limit Positions 15 6.7.4 Setting the PET Mode position 15 6.7.5 Reset all Factory Defaults 15 6.8 Testing & Setting Safety Obstruction Force 16 6.8.1 Testing the Close Cycle 16 6.8.2 Testing the Open Cycle 16 6.8.3 To Increase Force Pressure 16 6.8.4 To Decrease Force Pressure 16 6.8.5 To Recall Factory Set Force 16 6.9 Accessories 17 6.9.1 Terminal Block 17 6.9.2 Installation of Wall Control 17 6.10 Coding Transmitters 18 6.10.1 Setting Premium Remote Control and Wall Control Codes 18 6.10.2 To Erase Programmed Codes 18 6.10 Coding Transmitters 19 6.11 Auto-Close 20 6.11.1 Safety Beams 20 6.11.2 Auto Close Option 20 6.12 Attach Warning Labels 21 7. Operation Instructions 22 7.1 How to Use Your Operator 23 7.1.1 To Operate the opener: 23 7.1.2 Replacing the Battery: 3V Lithium Battery CR2032. 23 7.2 User Operating Controls 24 7.3. Door Status Indicators 24 8. User Maintenance I nstruction 25 8.1 Door Maintenance 25 8.2 If You Need a Service Call 25 9. T roubleshooting 26 10. Customer Agreement & Warranty 27 4 Dominator EasyRoller Instruction Manual 1. Safety Information Please read these important safety rules These safety alert symbols indicate a personal safety or property damage instruction exists. READ THESE INSTRUCTIONS CAREFULLY. This automatic garage door operator is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules. Failure to comply with the installation instructions and the safety warnings may result in death, serious personal injury and/or property damage. WARNING! •This operator should be installed in accordance with relevant US and Canada Standards. •To reduce the risk of injury to persons – Use this operator only with a rolling door. The drive must not be used with a door incorporating a wicket door, unless the drive cannot be operated with the wicket door open. •This operator is a plug in domestic appliance and is designed for indoor use only. It must be installed in a dry position that is protected from the weather. •Door must have Safety Beams fitted. •Activate the operator only when the garage door is in full view, free of obstructions and with the operator properly adjusted. •The network device allows for operation of the door when not in line- of-sight of the door and operator. Therefore the door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door. •Watch the moving door and keep people away until the door is completely opened or closed. ELECTROCUTION: •Installation and wiring must be in compliance with your local building and electrical codes. •This operator is not equipped for permanent wiring. Contact a qualified electrician to install a suitable receptacle if one is not available. •To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. •If the power cord is damaged, it must b…

Text truncated - open the document above for the full version.

17 February 2021 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: X4K-WPTX5V102B. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram CONF_WTX-4V2AM_Blkdia.pdf Schematics CONF_WTX-4V2AM_Schem.pdf Operational Description CONF_WTX-4V2AM_OpDes.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Nikolai Klepikov Senior Electronics Design Engineer

EMC Technologies Pty Ltd, 176 Harrick Road, Keilor Park VIC 3042 Australia www.emctech.com.au To: Federal Communications Commission Attention: Certification Officer Date: March 3, 2021 EMC Ref: M2102013 Subject: FCC FILING – ORIGINAL CERTIFICATION - FCC ID: X4K-WPTX5V102B Company: Automatic Technology (Australia) Pty Ltd FCC ID: FCC ID: X4K-WPTX5V102B EUT: Wall Control Test Firm: EMC Bayswater Pty Ltd (Accredited Test Site Designation No. A0004) Automatic Technology (Australia) Pty Ltd is applying for FCC Certification of the Wall Control (Wall Mounted Remote Control – Model WTX-4V2AM). The device is a wall mounted transmitter used to control (open and close) Garage door openers, Gate openers and other ATA equipment which require remote operations. The device is sold as part of the Dominator range of garage door operators therefore the supplied user manual includes a section specific to this transmitter (Refer to supplied user manual exhibit: 160402_00 GDO-6V4AM Dominator EasyRoller Instruction Manual - pages 17, 18, 21 for device details and page 19 for FCC and ISED Canada regulatory compliance statements). Testing was performed in accordance with the requirements of FCC 15C, Section 15.231. EMC Technologies Pty Ltd is acting as agent for Automatic Technology (Australia) Pty Ltd in this application. Best Regards _____________ Chris Zombolas Technical Director EMC Technologies Pty Ltd 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph. +61 3 9365 1000; www.emctech.com.au EMC Technologies Pty Ltd ABN 82 057 105 549 176 Harrick Road, Keilor Park, VIC 3042 Australia Ph: + 613 9365 1000 Fax: + 613 9331 7455 Email: [email protected]

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 17 February 2021 SUBJECT: FCC Application for FCC ID: X4K-WPTX5V102B To Whom It May Concern: We, the undersigned, hereby authorize Chris Zombolas at EMC Technologies Pty Ltd on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Chris Zombolas on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Nikolai Klepikov Senior Electronics Design Engineer

Page 1 of 3 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex A: External - EUT Photographs Automatic Technology Australia Pty. Ltd. WTX-4V2AM Wall Mounted Remote Control REPORT: E2102-1390-1 Annex A DATE: February, 2021 EMC Bayswater Test Report E2102-1390-1 Annex A Page 2 of 3 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – External Views 2 3 4 5 6 EMC Bayswater Test Report E2102-1390-1 Annex A Page 3 of 3 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6

Automatic Technology Australia Pty Ltd. Model WTX-4V2AM This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation. FCC ID: X4K-WPTX5V102B IC: 8880A-WPTX5V102B Made in China N.K. 08.02.21

Page 1 of 5 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex B: Internal - EUT Photographs Automatic Technology Australia Pty. Ltd. WTX-4V2AM Wall Mounted Remote Control REPORT: E2102-1390-1 Annex B DATE: February, 2021 EMC Bayswater Test Report E2102-1390-1 Annex B Page 2 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – Internal Views 2 3 4 5 6 7 8 9 10 11 12 13 Transmitter battery EMC Bayswater Test Report E2102-1390-1 Annex B Page 3 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2102-1390-1 Annex B Page 4 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10 Photograph 11 Photograph 12 EMC Bayswater Test Report E2102-1390-1 Annex B Page 5 of 5 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 13

Page 1 of 35 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 RADIO CERTIFICATION REPORT In accordance with: CFR47 FCC Part 15, Subpart C – Section 15.231 Automatic Technology Australia Pty. Ltd. WTX-4V2AM Wall Mounted Remote Control FCC ID: X4K-WPTX5V102B REPORT: E2102-1390-1 DATE: February, 2021 Accreditation Number: 18553 Accredited for compliance with ISO/IEC 17025 The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. EMC Bayswater Test Report E2102-1390-1 Page 2 of 35 Prepared & tested by: Approved by: 26/02/2021 16:21 Adnan Zaman (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Certificate of Compliance EMC Bayswater Test Report: E2102-1390-1 Issue Date: February, 2021 Product(s): Wall Mounted Remote Control Model No: WTX-4V2AM Serial No: Not stated Product Marketing Name (PMN): WALL CONTROL Variant: None FCC ID: X4K-WPTX5V102B Client Details: Mr. Nikolai Klepikov Automatic Technology Australia Pty. Ltd. 6 – 8 Fiveways Boulevard Keysborough Victoria 3173 Australia Phone No: +61 3 9791 0275 Fax No: +61 3 9791 0250 e-mail: [email protected] Test Specification: CFR47 FCC Part 15, Subpart C – Section 15.231 Results Summary: FCC 15.203 - Antenna Requirement Complied FCC 15.231(a) - Transmitter Deactivation Complied FCC 15.231(b) - Field strength of fundamental Complied FCC 15.231(b), 15.209 - Field strength of spurious emissions Complied FCC 15.231(c) - Emission Bandwidth Complied Test Date(s): 12 th and 15 th of February, 2021 Test House (Issued By): EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria 3136 Australia FCC Accredited Test Firm Registration number: 527798 FCC Accredited Test Firm Designation number: AU0004 Phone No: +61 3 9761 5888 e-mail: [email protected] Fax No: +61 3 8761 6547 Web: www.emcbayswater.com.au This is to certify that the necessary measurements were made by EMC Bayswater Pty Ltd, and that the Automatic Technology Australia Pty. Ltd., WTX-4V2AM, Wall Mounted Remote Control, has been tested in accordance with requirements contained in the appropriate commission regulations. EMC Bayswater Test Report E2102-1390-1 Page 3 of 35 Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Radio Certification Report for Automatic Technology Australia Pty. Ltd. Contents 1. Introduction ................................................................................................................... 4 2. Test Report Revision History ........................................................................................ 4 3. Report Information ........................................................................................................ 4 4. Summary of Results ...................................................................................................... 4 5. Product Sample, Configuration & Modifications ......................................................... 5 5.1. Product Sample Details ............................................................................................ 5 5.2. Product description ................................................................................................... 5 5.3. Support Equipment ................................................................................................... 6 5.4. Product operating modes .......................................................................................... 6 5.5. Product operating mode for testing ........................................................................... 6 5.6. Configuration ............................................................................................................ 6 5.7. Modifications ............................................................................................................. 6 5.8. Test Facility .............................................................................................................. 6 5.9. Test Equipment ........................................................................................................ 6 6. Referenced Standards ................................................................................................... 7 7. Referenced Documents ................................................................................................. 7 8. Antenna Requirement – FCC Part 15.203 ..................................................................... 8 8.1. Requirements ........................................................................................................... 8 8.2. Result .........................................................................…

Text truncated - open the document above for the full version.

Page 1 of 4 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex C: Test Configuration Photographs Automatic Technology Australia Pty. Ltd. WTX-4V2AM Wall Mounted Remote Control REPORT: E2102-1390-1 Annex C DATE: February, 2021 EMC Bayswater Test Report E2102-1390-1 Annex C Page 2 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT X orientation 2 EUT Z orientation 3 Field strength of fundamental, Duty cycle and Emission Bandwidth – Test configuration Field strength of spurious emissions – Test configuration – 30MHz to 1GHz 4 5 Field strength of spurious emissions – Test configuration – 9kHz to 30MHz 6 7 8 Field strength of spurious emissions – Test configuration – 1GHz to 4.5GHz 9 EMC Bayswater Test Report E2102-1390-1 Annex C Page 3 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E2102-1390-1 Annex C Page 4 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9