X5Y774-0788NBPUMA T3 Plus/806-870

P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 Safety recommendations Carefully read all of the cautions and warnings before using theradio: • Do not use the radio equipment for uses different thanthose indicated in the present guide. • For a correct use of the radio read what is listed in thisguide. • Protect the radio from sprinklings of water and/or otherliquids and from dust. • Do not bring the radio close to heat sources. • Do not place the hand-held radio above the airbags orin their area of action. If the airbag is activated, it maynot swell correctly and/or hurl the portable unit, withgreat force, inside the passenger compartment whereare located the vehicle occupants. • The external antenna connector, not used during normaloperations, must be protected by proper cover. • First and second maintenance level interventions onthe equipment are to be carried out by authorizedtechnicians only. Third maintenance level interventionsare to be carried out by SELEX technicians only. Themaintenance levels are defined in the technical manual. • Use only original accessories and spare parts,approved by the manufacturer, suitable for the PUMAT3 PLUS. The use of different accessories and/or spareparts (earphone, antenna, etc.) makes the safety andelectromagnetic compatibility certifications to be validno more and it could lower the user safety level and/orgenerate electromagnetic fields that exceed theaccepted limits. • Follow the battery charger instructions in order to useit correctly. • During voice calls, the PUMA T3 PLUS use with itsproper leather bag is recommended in environmentswhith temperature greater than 45 °C. • The emergency call is a priority type call. The hand-held radio, like all mobile telephony equipment, operateswith radio frequency signals, therefore, the forwardingof the call depends on the network coverage at themoment of the call. • If you need send an emergency call, keep pressed theemergency button for at least 2 seconds, when theradio is switched on. In fact, a switched off radio canbe turned on by keeping pressed the emergency key,but for an outgoing emergency call a new pressure ofthe related button must be done.Relating to the radio setting (from PRP), two cases mayoccur if the transmission is inhibit:a) the emergency call is not sent; it is necessary to disable the Tx Inhibit function from radio menu toforward a call (even if the call is an emergencycall). b) the emergency call is sent and automatically the Tx Inhibit function is disabled; from radio menu it ispossible to recover the Tx Inhibit function again. WARNING This equipment is markedAccording to the requirements specified in the R&TTE directive1999/5/EC and the Commission Decision 6th April 2000, theEC marking is accompanied by the Class II equipment classidentifier.The equipment (in the 380÷430 MHz and 410÷470 MHzversions) is intended for sell and use in AT, BE, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, SK, SI, ES,SE, GB.This equipment requires authorization or license for use.This equipment operates on frequency bands non-harmonised in the EU.This equipment can also be used worldwide where theequipment is approved for use. FCC APPROVAL For US owners onlyFCC approvalPUMA T3 Plus/806-870 Hand Held equipment complies withPart 15 of the FCC/Federal Communication Commissionregulations.Operation is governed by the following:FCC ID: X5Y774-0788 FCC ID: X5Y774-0788NB These devices comply with part 15 of the FCC Rules.Operation is subject to the following two conditions:- these devices may not cause harmful interference, and- these devices must accept any interference received, including interference that may cause undesired operation.Any unauthorized modifications or changes to thesedevices could void the user's authority to operate thesedevices.Note:FCC ID X5Y774-0788 and FCC ID X5Y774-0788NB apply toPUMA T3 Plus/806-870 versions only. • Hold the radio in a vertical position in front of face with the microphone (and the other parts of the radio, including theantenna) at least one inch (2.5 cm) away from the nose. Keepingthe radio at the proper distance is important because RFexposures decrease with distance from the antenna. Antenna should be kept away from eyes. • When worn on the body, always place the radio in a SELEX Elsag approved clip, holder, holster, case, or body harness forthis product. Using approved body-worn accessories isimportant because the use of Selex Elsag or othermanufacturer's non-approved accessories may result inexposure levels, which exceed the FCC's occupational/controlled environment RF exposure limits. • If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, thenensure the antenna and the radio are kept at least 2.5 cm (oneinch) from the body when transmitting. Keeping the radio at theproper distance is important because RF exposures decreasewith increasing distance from the antenna. • Use only SELEX Elsag approved supplied or replacement antennas, batteries, and accessories. Use of non-manufacturer-name approved antennas, batteries, and accessories mayexceed the FCC RF exposure guidelines. • For a list of SELEX Elsag approved accessories (see the user manual), or (visit the following website which lists approvedaccessories: http://intranet.selexelsag.com, or (contact the radio manufacturer at customer [email protected]) Contact InformationFor additional information on exposure requirements or otherinformation, contactcustomer [email protected] P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 • Carry out the maintenance interventions on the hand heldradio following the instructions given in the technicalmanual. • Follow all accident prevention standards when carryingout maintenance interventions on the hand held radioequipment and use the proper tools (spanners,screwdrivers,.....). • Do not use the radio if the antenna is damag…

Text truncated - open the document above for the full version.

P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 P/N MAN-0696/01.01 Group Mng (only TETRA)(group management)Calls (only TETRA)Delivery Options (onlyTETRA)(to select the kind of mes-sages delivery report)Tx Inhibit (only TETRA)(to disable/enable thetransmission)Group (only FM)(to select the active group/channel)Dead Man(to enable/disable therelative functionality)PreferencesBluetoothAccessories © 2010 SELEX Communications S.p.A. - All rights reserved.SELEX Communications S.p.A. reserves the right to change specifications, performance or features relevant to the product descri bed without notice. This is an unpublished work the copyright in which vests in SELEX Communications S.p.A. The information contain ed herein is confidential and the property of SELEX Communications S.p.A. and is supplied without liability for errors or omission s. No part may be reproduced, disclosed or used except as authorised by contract or other written permission. Handportable radio Quick reference guide SELEX Communications S.p.A. A Finmeccanica Company Via Pieragostini, 80, 16151 - Genova, Italy Before using the equipment, read all theinstructions contained in the present guide and,with special care, those relative to safety. WARNING Menu structure  NOTE : — Some menus can be or not available according to the configurationof the radio terminal. — Choosing some options of WPS menus can cause the ending of active group calls. E2EE Status(enable/disable E2EE) Phone Book (only TETRA)(user defined)Home TETRA (only TETRA)(pre-configured phonebook)Non TETRA (only TETRA) (pre-configured phonebook, TMO only) Group Scanning(to enable/disable it)WPS SelectionWPS UpdateWPS ReconfigureActive WPS(to change the configura-tion of the active WPS)Extra WPS(to move the groupsassigned by DGNA in thecurrent WPS) Key Access(direct access keys are shown)Dialling (only TETRA)(dialling digits are shown)Supplementary String (onlyTETRA)(supplementary strings areshown)Symbols(symbols meaning is shown) Activation/DeactivationDevicesActive ConnectionOffered Services Find NewDevices List Displayed symbols Signal level (TMO channel)Network (search if flashing)Direct ModeDirect Mode with DM-GATEWAY equipment presencedetectedDirect Mode with DM-REP equipment presence detectedE2E Crypto enabledPresence of not read messages in the In-Box. If thesymbol is blinking the queue is full, and there is at leastone message not readFull Queue, each message is readActive Data CallFallback modeEarphone speech CallSpeech connection active, loudspeaker modeKeypad Volume OFFKeypad lockedGroup Scanning enabledGroup Att ach Failure Group selector enabled, displayed alternatively toBattery level indicationPacket Data ContextPacket Data ChannelHeadset detectedBluetooth activated (*)Handset detectedGPS External Device detectedCar kit detectedUHF Simplex channelUHF Network channelCustom E2EE enabledCustom E2EE errorVOX enabledTransmission active Menu Main controls and indicators During normal operation the knob has the volume controlfunction, turn it clockwise to turn up the volume of the audiooutput of the loudspeaker/earphone.Turn the knob counterclockwise to decrease the volume.If the knob is kept pressed until the alternate symbols and appear on the display it goes to group-channel selection function. Once in this modality turn the knob to chooseamong the available groups and select the group-channel bypressing the knob. Once pressed the knob you go back tovolume control function. If, in group-channel selection modality,no operation on the knob is performed for a pre-defined timeinterval, the knob automatically changeovers to volumecontrol function.Keep pressed the emergency key for at least 2 seconds tosend an emergency alarm, when the radio is on. When theradio is off pressing the emergency key will turn on the radio.Right navigation key: it's usually related to the BACK/CLEARoption. When the radio is in idle status it allows the accessto send status menu; during calls using this key it is possibleto send DTMF tones (only TETRA).Up/down navigation key. In idle status allows to access thephone lists menu. It changes conversation mode (fromloudspeaker to earphone and vice versa) during calls.Left navigation key, for menu options selection. In idle st atus and during calls it allows the access to the main menu.Keep pressed for a few seconds to switch on/off the radio. Ifpressed during communication it interrrupts the connection.Speaker used for Loudspeaker conversation mode.Off hook key, to accept/make (after having typed in theaddress) an individual full duplex call; if pressed in idle statusit allows to access the list of the last calls (made/received).Push-To-Talk button, press it to talk during half-duplex conversation. If pressed (in idle status when a group isselected, or after having typed in a group address) it sendsa call to the selected group/channel.If the network allows this function, pressing PTT(1) in idlestatus when a group is selected the first available dispatcherof the selected group is called (not the group). Otherwise,after having typed in the address, press PTT(1) to make thehalf duplex individual call.It is lit while the radio is transmitting; blinking in Tx Inhibitmode (only TETRA).It is lit while the radio is receiving.Small speaker used for earphone conversation mode. Group -channelSelector /VolumeControllerEmergencykeyLoudspeakerPTTPTT(1)Red LedGreen LedEarphone PIN(to change/enable/disable it)Talk (only TETRA)(to select the default conversa-tion mode loudspeaker/ear-phone for direct incoming calls)LanguageSounds(to disable and to control thesounds volume)Display D P F G P S UHF VOX  NOTE : For what concerns technical characteristics, reference standard,maintenance and troubleshooting, refer to the relevant technicalhandbook. & FM PUMA T3 PLUS PUMA T3 PLUS Messages Change Mode (TMO/DMO/FM) Encryption (only TETRA) Phone Lists Settings Monitor (to check radio coverage, only FM) GPS Information Help Late Entry(to enable/disable t…

Text truncated - open the document above for the full version.

Legal details: Via G. Puccini 2 – 16154 Genoa (Italy) Stock capital Euro 60.000.000 fully paid up Fiscal code Genoa's Company Register number 00808100010 V.A.T. 03299110100  Copyright SELEX Elsag S.p.A. - All Rights Reserved Page 1 of 3 Via G. Puccini 2 16154 Genova – Italy SELEX Elsag S.p.A. A wholly-owned subsidiary of Finmeccanica S.p.A. A Finmeccanica Company NON-DISCLOSURE AGREEMENT Code 6AA-GA100368 Ed. 02 This Confidentiality Agreement (hereinafter briefly referred to as Agreement) is stipulated on this ................ and is to be deemed applicable to all information as will be exchanged between the contracting parties within their commercial relationships. The contracting parties are: SELEX Elsag S.p.a, a company subject to direction and coordination of Finmeccanica S.p.a, with registered head office in Genoa, via G. Puccini 2, share capital Euro 60,000,000.00= fully paid up, entered in the Register of Companies of Genoa under No. 00808100010, VAT number 03299110100 and .................................... with registered office in ........................ address .................., share capital ..................... entered in the Register of Companies of ................. under No. ................ VAT number .................. The said Companies may henceforth also be referred to individually as Party, and collectively as Parties. A. For the purposes of this Agreement, the expression “Confidential Information” shall indicate all information (of financial, technical, commercial and any other nature whatsoever), transmitted by a party (the Issuer) to the other (Receiver), either directly or through other parties, within the same Agreement, or anyway within subsequent agreements, invitations to offer, purchase orders, contracts, etc., be it verbal or written or consisting of images, samples, instruments, source-code or object-code software, as well as any other connected information, under any form whatsoever, including, for example and without limitation, data relating to computer programs, models and similar, markets, “business plans”, agreements with third parties, services, customers, commercial or financial aspects of the Issuer, provided that such information, if supplied in writing, reports in a clear and evident manner the expression “proprietary” or “confidential” or, if supplied orally or by images, or however in any non-written form, is identified as “Confidential Information” at the moment that it is given and such qualification is confirmed in writing within 30 (thirty) days. At any rate, during such period all cautions and restrictions set forth in this Agreement for the use and disclosure of “Confidential Information” shall be applied. “Confidential Information” shall also include any information obtained further to examination, testing or analysis of any hardware element, or part thereof, supplied by the “Issuer", even though the above evidence and qualification requirements are not fulfilled. B. The Receiver shall: a) Keep the “Confidential Information” strictly as such and limit the relevant access only to those employees for whom it is necessary within the commercial relationships of the Parties: b) not use the “Confidential Information” for purposes other than those indicated above; c) not disclose the “Confidential Information” without a prior consent in writing from the “Issuer”. It remains understood, however, that each Party shall allow access to “Confidential Information” only to employees of companies of their own Group – or to external Auditors (henceforth also “Auditors”) – who need it exclusively with regard to the subject matter hereof between the Parties. In addition, they shall ensure that such employees or Auditors be previously informed of the confidentiality obligations under this Agreement. The expression Group shall mean, for each Party, the same Party and its subsidiaries – i.e. companies in which such Party has a participation interest exceeding 50% of the share capital – as well as, with regard to SELEX Elsag, the controlling company Finmeccanica S.p.A. Legal details: Via G. Puccini 2 – 16154 Genoa (Italy) Stock capital Euro 60.000.000 fully paid up Fiscal code Genoa's Company Register number 00808100010 V.A.T. 03299110100 Cod. 6AA-GA100368 Ed. 02 NON-DISCLOSURE AGREEMENT  Copyright SELEX Elsag S.p.A. - All Rights Reserved Page 2 of 3 Via G. Puccini 2 16154 Genova – Italy SELEX Elsag S.p.A. A wholly-owned subsidiary of Finmeccanica S.p.A. C. The obligations and restrictions under the preceding item shall not apply to information in respect of which the “Receiver” is able to prove: a) that it was already known to such Party, without any limitation to its use or diffusion, prior to its transmission under this Agreement; b) that it is public, or has become such, for reasons other than the stipulation/termination of the Agreement; c) that it has been legally obtained from a third party, with no communication relevant to the presence of restrictions to its use and diffusion; d) that it has been developed and inferred by the “Receiver” independently of the received “Confidential Information”; e) that it is used or spread in compliance with laws or regulations or pursuant to measures of Authorities. D. For the purposes of this Agreement, “Classified Information” shall mean information, documents and any kind of news which the Government of the “Issuer’” Country has submitted or intends to submit to security measures, regardless of whether such information is transmitted orally, electronically, in writing or by material delivery. Each Party therefore undertakes to apply the provisions relevant to such security measures, as transmitted to such Party by the “Issuer” and set forth by the national Government of the latter with regard to:  disclosure of “Classified Information”;  reception of “Classified Information”;  protection, use and treatment of “Classified Information”. the provisions of this clause shall at any rate remain in force even…

Text truncated - open the document above for the full version.

TETRA TERMINAL DEVICES 870 TUNE UP INFORMATIONS 19/07/2012 codice tecnico . 1 A Finmeccanica Company FCC ID: X5Y774-0788 Product Name: PUMA T3 Plus/806-870 FCC ID: X5Y774-0788NB Product Name: PUMA T3 Plus/806-870 FCC ID: X5Y774-0850 Product Name: VS3000 GTW/806-870 FCC ID: X5Y774-0850NB Product Name: VS3000 GTW/806-870 Tune up Informations No tune up procedure is required by technician or user after the device has left the factory to match its specifications on the working frequency. The PUMA T3 Plus/806-870 and VS3000 GTW/806-870 device has no manual trimmers or adjustments that can be manually done on it acting directly on the device itself.

The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-01. SAR_Report_Selex_60320_6120151_FCC_Tetra_850_PumaT3plus_870084 Page 1 of 34 Report Dosimetric Assessment of the Portable Device Selex Elsag S.p.A. PUMA T3 plus (FCC ID: X5Y774-0788NB) According to the FCC Requirements July 31, 2012 IMST GmbH Carl-Friedrich-Gauß-Str. 2 D-47475 Kamp-Lintfort Customer Selex Elsag S.p.A. Via Giacomo Puccini 2 16154 Genova Italy The test results only relate to the items tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. SAR_Report_FCC_850_1900_CDMA2000_2450_1.0.doc/23.11.2011/AR SAR_Report_Selex_60320_6120151_FCC_Tetra_850_PumaT3plus_870084 Page 2 of 34 SAR_Report_FCC_850_1900_CDMA2000_2450_1.0.doc/23.11.2011/AR Executive Summary The device PUMA T3 plus is a new handheld device from Selex Elsag S.p.A. operating in the 850 MHz frequency range. The device has an extended antenna and the system concepts used is the TETRA standard. The integrated Bluetooth module is disabled. The objective of the measurements done by IMST was the dosimetric assessment of one device in head and body worn configuration in the 800 MHz range TETRA standard. Since in normal operation mode only 1 TX is active, SAR assessment has been conducted only in this TX configuration. The examinations have been carried out with the dosimetric assessment system „DASY4“. The measurements were made according to the Supplement C to OET Bulletin 65 of the Federal Communications Commission (FCC) Guidelines [OET 65] for evaluating compliance of mobile and portable devices with FCC limits for occupational/controlled exposure to radiofrequency emissions and IC RSS 102 Issue 4 and the following specific FCC Procedures:  KDB 648474 D01 SAR Handsets Multi Xmiter and Ant, v01r05  KDB 447498 D01 Mobile Portable RF Exposure v04  KDB 643646 D01 SAR Test for PTT Radios v01r01 All measurements have been performed in accordance to the recommendations given by SPEAG. SAR_Report_Selex_60320_6120151_FCC_Tetra_850_PumaT3plus_870084 Page 3 of 34 SAR_Report_FCC_850_1900_CDMA2000_2450_1.0.doc/23.11.2011/AR Compliance Statement The portable device PUMA T3 plus from Selex Elsag S.p.A. (FCC ID: X5Y774- 0788NB) is in compliance with the Federal Communications Commission (FCC) Guidelines [OET 65] for occupational/controlled exposure. The phone was tested in addition to the head positions in the following body worn configurations:  PTT configuration (25 mm)  Voice mode with shoulder belt Maximum SAR 1g = 2.160 W/kg (809.0125 MHz, right side, tilted position ) prepared by: ........................................... reviewed by:.............................................. Alexander Rahn André van den Bosch test engineer quality assurance engineer IMST GmbH Carl-Friedrich-Gauß-Straße 2 D-47475 Kamp-Lintfort Tel. +49- 2842-981 378 Fax +49- 2842-981 399 email: [email protected] SAR_Report_Selex_60320_6120151_FCC_Tetra_850_PumaT3plus_870084 Page 4 of 34 SAR_Report_FCC_850_1900_CDMA2000_2450_1.0.doc/23.11.2011/AR Table of Contents 1 SUBJECT OF INVESTIGATION ................................................................................................................... 5 2 THE IEEE STANDARD C95.1-1999 AND THE FCC EXPOSURE CRITERIA ....................................... 5 2.1 DISTINCTION BETWEEN EXPOSED POPULATION, DURATION OF EXPOSURE AND FREQUENCIES ........... 5 2.2 DISTINCTION BETWEEN MAXIMUM PERMISSIBLE EXPOSURE AND SAR LIMITS ....................................... 6 2.3 SAR LIMIT .................................................................................................................................................. 6 3 THE FCC MEASUREMENT PROCEDURE ................................................................................................ 7 3.1 GENERAL REQUIREMENTS......................................................................................................................... 7 3.2 DEVICE OPERATING NEXT TO A PERSON’S EAR ....................................................................................... 7 4 BODY-WORN CONFIGURATIONS ........................................................................................................... 10 4.1 POC (PTT) POSITION .............................................................................................................................. 11 4.2 PHANTOM REQUIREMENTS ...................................................................................................................... 11 4.3 TEST TO BE PERFORMED ......................................................................................................................... 11 5 THE MEASUREMENT SYSTEM ................................................................................................................ 12 5.1 PHANTOM ................................................................................................................................................. 14 5.2 PROBE ...................................................................................................................................................... 14 5.3 MEASUREMENT PROCEDURE .................................................................................................................. 15 5.4 UNCERTAINTY ASSESSMENT ................................................................................................................... 16 6 KDB CONSIDERATIONS ............................................................................................................................. 17 6.1 KDB 648474 D01 SAR HANDSETS MULTI XMITER AND ANT, V01R05 ................................................ 17 6.2 KDB 447498 D01 MOBILE PORTABLE RF EXPOSURE V04 ...........................................................…

Text truncated - open the document above for the full version.

The Testcenter facility ‘Dosimetric Test Lab’ within IMST GmbH is accredited by the German National ‘Deutsche Akkreditierungsstelle GmbH (DAkkS)’ for testing according to the scope as listed in the accreditation certificate: D-PL-12139-01-01. SAR_Report_Selex_60320_6120151_FCC_Plots_Tetra_850_PumaT3plus_870084 Page 1 of 22 Appendix for the Report Dosimetric Assessment of the Portable Device Selex Elsag S.p.A. PUMA T3 plus (FCC ID: X5Y774-0788NB) According to the FCC Requirements SAR Distribution Plots July 31, 2012 IMST GmbH Carl-Friedrich-Gauß-Str. 2 D-47475 Kamp-Lintfort Customer Selex Elsag S.p.A. Via Giacomo Puccini 16154 Genova Italy The test results only relate to the items tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. SAR_Report_FCC_850_1900_CDMA2000_2450_1.0.doc/23.11.2011/AR SAR_Report_Selex_60320_6120151_FCC_Plots_Tetra_850_PumaT3plus_870084 Page 2 of 22 dasy_report_fcc_850_1900_plots_1.1.doc/04.07.2005/CH Table of Contents 1 SAR DISTRIBUTION PLOTS, TETRA HEAD ..................................................................................... 3 2 SAR DISTRIBUTION PLOTS, TETRA HEAD, PTT CONFIGURATION ........................................... 13 3 SAR DISTRIBUTION PLOTS, TETRA BODY ................................................................................... 17 4 SAR Z-AXIS SCANS (VALIDATION) ................................................................................................ 21 5 SAR Z-AXIS SCANS (MEASUREMENTS) ........................................................................................ 22 SAR_Report_Selex_60320_6120151_FCC_Plots_Tetra_850_PumaT3plus_870084 Page 3 of 22 dasy_report_fcc_850_1900_plots_1.1.doc/04.07.2005/CH 1 SAR Distribution Plots, TETRA, Head Test Laboratory: Imst GmbH, DASY Yellow (II); File Name: 084_ytlm_1_group1.da4 DUT: SELEX; Type: PUMA T3 Plus; Serial: 870084 Program Name: Cheek Left Communication System: Tetra; Frequency: 809.013 MHz;Duty Cycle: 1:4 Medium parameters used (extrapolated): f = 809.013 MHz; σ = 0.898 mho/m; ε r = 42.1; ρ = 1000 kg/m 3 Phantom section: Left Section DASY4 Configuration: - Probe: ET3DV6R - SN1579; ConvF(6.34, 6.34, 6.34); Calibrated: 25.01.2012 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 20.02.2012 - Phantom: SAM Sugar 1341; Type: QD 000 P40 CB; Serial: TP-1341 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Cheek Left/Area Scan (7x18x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.22 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 37.7 V/m; Power Drift = 0.121 dB Peak SAR (extrapolated) = 2.03 W/kg SAR(1 g) = 1.28 mW/g; SAR(10 g) = 0.842 mW/g Maximum value of SAR (measured) = 1.49 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 1: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 37.7 V/m; Power Drift = 0.121 dB Peak SAR (extrapolated) = 1.05 W/kg SAR(1 g) = 0.838 mW/g; SAR(10 g) = 0.646 mW/g Maximum value of SAR (measured) = 0.919 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 2: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 37.7 V/m; Power Drift = 0.121 dB Peak SAR (extrapolated) = 1.74 W/kg SAR(1 g) = 0.927 mW/g; SAR(10 g) = 0.640 mW/g Maximum value of SAR (measured) = 1.29 mW/g Fig. 1: SAR distribution for Tetra, 809.0125 MHz, cheek position, left side of head (July 24, 2012; Ambient Temperature: 22.8° C; Liquid Temperature: 22.5° C). SAR_Report_Selex_60320_6120151_FCC_Plots_Tetra_850_PumaT3plus_870084 Page 4 of 22 dasy_report_fcc_850_1900_plots_1.1.doc/04.07.2005/CH Test Laboratory: Imst GmbH, DASY Yellow (II); File Name: 084_ytlm_1_group3.da4 DUT: SELEX; Type: PUMA T3 Plus; Serial: 870084 Program Name: Cheek Left Communication System: Tetra; Frequency: 823.987 MHz;Duty Cycle: 1:4 Medium parameters used (extrapolated): f = 823.987 MHz; σ = 0.91 mho/m; ε r = 42; ρ = 1000 kg/m 3 Phantom section: Left Section DASY4 Configuration: - Probe: ET3DV6R - SN1579; ConvF(6.34, 6.34, 6.34); Calibrated: 25.01.2012 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn335; Calibrated: 20.02.2012 - Phantom: SAM Sugar 1341; Type: QD 000 P40 CB; Serial: TP-1341 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Cheek Left/Area Scan (7x18x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.18 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 37.9 V/m; Power Drift = -0.138 dB Peak SAR (extrapolated) = 2.01 W/kg SAR(1 g) = 1.17 mW/g; SAR(10 g) = 0.786 mW/g Maximum value of SAR (measured) = 1.34 mW/g Cheek Left/Zoom Scan (7x7x7)/Cube 1: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 37.9 V/m; Power Drift = -0.138 dB Peak SAR (extrapolated) = 1.04 W/kg SAR(1 g) = 0.787 mW/g; SAR(10 g) = 0.621 mW/g Maximum value of SAR (measured) = 0.876 mW/g Fig. 2: SAR distribution for Tetra, 823.9875 MHz, cheek position, left side of head (July 24, 2012; Ambient Temperature: 22.8° C; Liquid Temperature: 22.5° C). SAR_Report_Selex_60320_6120151_FCC_Plots_Tetra_850_PumaT3plus_870084 Page 5 of 22 dasy_report_fcc_850_1900_plots_1.1.doc/04.07.2005/CH Test Laboratory: Imst GmbH, DASY Yellow (II); File Name: 084_ytlm_1_group4.…

Text truncated - open the document above for the full version.