X5YVS4000-806-870VS4000 806-870

VS4000 UHF Vehicle Radio Equipment Technical Handbook P/N: MAN-0974/01 Rev. 01 VS4000 Technical Handbook Page ii Selex ES - Proprietary information P/N: MAN-0974/01 Rev. 01 The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This document is intended for the use of Selex ES customers only for the purposes of the agreement under which the document is submitted, and no part of it may be reproduced or transmitted in any form or means without the prior written permission of Selex ES . The document has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Selex ES welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this document concerning the suitability, capacity, or performance of the mentioned hardware or software products cannot be considered binding but shall be defined in the agreement made between Selex ES and the customer. However, Selex ES has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Selex ES will, if necessary, explain issues which may not be covered by the document. Selex ES liability for any errors in the document is limited to the documentary correction of errors. Selex ES WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THIS DOCUMENT OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL (INCLUDING MONETARY LOSSES), that might arise from the use of this document or the information in it. This document and the product it describes are considered protected by copyright according to the applicable laws. Other product names mentioned in this document may be trademarks of their respective companies, and they are mentioned for identification purposes only. Copyright © Selex ES S.p.A. 2013. All rights reserved Selex ES S.p.A. A Finmeccanica Company VS4000 Technical Handbook Safety rules Selex ES - Proprietary information Page iii Safety rules Before using the equipment, read all the instructions contained in the manual and with special care those relative to safety. Lue käyttöohjeet ja erityisesti turvallisuuteen liittyvat ohjeet ennen laitteen käyttöä. Alvorens over te gaan tot het gebruik van het apparaat lees met aandacht al de instructies van het handboek en let vooral op die die de veiligheid betreffen. Alvorens het apparaat in gebruik te nemen lees alle instructies van het handboek en vooral de voorschriften betreffende de veiligheid. Avant toute utilisation de l’appareil, lire toutes les indications contenues dans le Manuel et avec une attention particulière celles relatives à la sécurité. Läs alla instruktioner i denna manual innan ni använder apparaten och då särskilt noggrannt de anvisningar som gäller säkerheten. Læs alle de vejledninger, der er indeholdt i manualen med særlig opmærksomhed på de vejledninger, der vedrører sikkerheden, før apparatet tages i brug. Vor Gebrauch des Geräts alle in dieser Bedienungsanleitung enthaltenen Anweisungen und Vorschriften lesen. Den Sicherheitsbestimmungen ist dabei besondere Aufmerksamkeit zu widmen. VS4000 Technical Handbook Safety rules Page iv Selex ES - Proprietary information P/N: MAN-0974/01 Rev. 01 Πριν χρησιμοποιήσετε τη συσκευή διαβάστε όλες τις οδηγίες που περιέχονται στο εγχειρίδιο και δώστε ιδιαίτερη προσοχή στης οδηγίες ασφαλείας. Prima di utilizzare l’apparecchiatura leggere tutte le indicazioni contenute nel manuale e con particolare attenzione quelle relative alla sicurezza. Antes de utilizar el equipo leer todas las instrucciones contenidas en el manual, poniendo particular atención a las de seguridad. Antes de utilizar o aparelho, leia todas as instruções que constam no manual e com muita atenção as instruções relativas à segurança. VS4000 Technical Handbook Safety rules Selex ES - Proprietary information Page v This equipment is marked According to the requirements specified in the R&TTE directive 1999/5/EC and the Commission Decision 6th April 2000, the EC marking is accompanied by the Class II equipment class identifier. This equipment is intended for sell and use in AT, BE, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, SK, SI, ES, SE, GB. This equipment requires authorization or license for use. This equipment operates on frequency bands non-harmonised in the EU. This equipment can also be used worldwide where the equipment is approved for use VS4000 Technical Handbook Safety rules Page vi Selex ES - Proprietary information P/N: MAN-0974/01 Rev. 01 Selex ES S.p.A. tímto prohlašuje, že tento VS4000 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede Selex ES S.p.A. erklærer herved, at følgende udstyr VS4000 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Hiermit erklärt Selex ES S.p.A., dass sich das Gerät VS4000 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigeneinschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Käesolevaga kinnitab Selex ES S.p.A. seadme VS4000 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Hereby, Selex ES S.p.A., declares that this VS4000 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente Selex ES S.p.A. declara que el VS4000 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Selex ES S.p.A. ΔΗΛΩΝΕΙ ΟΤΙ VS4000 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Par la présente Selex ES S.p.A. déclare que l'appareil VS4000 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive …

Text truncated - open the document above for the full version.

Federal Communications CommissionFCC 11-63 Beforethe Federal Communications Commission Washington, D.C. 20554 In the Matter of Amendment of Part 90 of the Commission’s Rules to Permit Terrestrial Trunked Radio (TETRA) Technology Request by the TETRA Association for Waiver of Sections 90.209, 90.210 and 2.1043 of the Commission’s Rules ) ) ) ) ) ) ) ) ) ) WT Docket No. 11-69 ET Docket No. 09-234 NOTICE OF PROPOSED RULE MAKING AND ORDER Adopted: April 18, 2011Released: April 26, 2011 Comment Date:[45 days after publication in the Federal Register] Reply Comment Date:[60 days after publication in the Federal Register] By the Commission: I.INTRODUCTION 1.In this Notice of Proposed Rule Making and Order, we propose to modify our rules to permit the certification and use of Terrestrial Trunked Radio (TETRA) equipment under Part 90 of our Rules. 1 TETRA is a spectrally efficient digital technology with the potential to provide valuable benefits to land mobile radio users. It does not, however, conform to all of our Part 90 technical rules. The TETRA Association (the Association) 2 filed a request for waiver of the Part 90 occupied bandwidth limit and emission masks, in order to permit implementation of TETRA technology in the United States. For the reasons set forth below, we grant the waiver request in part, to permit certification and use of TETRA equipment, subject to certain conditions, pending the outcome of this rulemaking proceeding. II.BACKGROUND 2.Subpart I of Part 90 of our Rules sets forth the general technical requirementsfor use of frequencies and equipment in the private land mobile radio services. Such requirements include standards for acceptability of equipment, frequency tolerance, modulation, emissions, power, and bandwidths. 3 The purpose of these technical standards is to limit wireless systems’ interference potential. 4 The Association 1 47 C.F.R. Part 90. 2 See Request for Waiver of Sections 90.209, 90.210 and 2.1043 (filed November 20, 2009) (Request). The TETRA Association is composed of 150 organizations from 37 countries, and promotes the use of TETRA technology around the world. Id.at 2. 3 See 47 C.F.R § 90.201. 4 See Biennial Regulatory Review –Amendment of Parts 1, 22, 24, 27, and 90 to Streamline and Harmonize Various Rules Affecting Wireless Radio Services, Report and Order and Notice of Proposed Rulemaking, WT Docket No. 03-264, 20 FCC Rcd 13900, 13923 n.168 (2005). Federal Communications CommissionFCC 11-63 2 asserts that, because the Part 90 technical rules were originally developed for analog technology, they are not always appropriate for evaluating more spectrally efficient digital technologies that have been developed. 5 3.TETRA is a digital, trunked radio technology that operates with Time Division Multiple Access (TDMA) in four-slot channels within a twenty-five kilohertz bandwidth. In 2009, the Association filed a request for waiver of Parts 2 and 90 of the Commission’s rules on behalf of manufacturers to allow TETRA technology to be used in the United States. The Association states that the TETRA standard, which was developed by the European Technical Standards Institute (ETSI), is used around the world, and that manufacturers are ready to produce TETRA devices for use in the United States on several frequency bands. 6 Italso states that TETRA technology provides better efficiency and security than available alternatives, 7 and offers interoperability among equipment from different manufacturers. 8 4.In order to permit implementation of TETRA technology in the United States, the Association requests waivers of the Part 90 occupied bandwidth limit and emission masks. For devices operating with twenty-five kilohertz channel spacing, Section 90.209(b)(5) of our Rules limits the authorized bandwidth to twenty kilohertz, 9 and Section 90.210 of our Rules specifies particular emission masks. 10 TETRA equipment, however, exceeds these limits, because the ETSI standard does not set occupied bandwidth limits. Instead, it sets standards for adjacent channel power and for unwanted emissions at different frequency offsets. This results in operation with a bandwidth of up to twenty-two kilohertz, 11 and excursions of up to five decibels from the Part 90 emission masks. 12 5.The Association also requests a waiver of the permissive change rules regarding equipment certification. Itnotes that certain manufacturers, in order to meet immediate demand for TETRA equipment, have obtained Commission certification of TETRA radios that comply with the Part 90 rules by using reduced power. Certain changes to approved equipment, including changes to the maximum 5 See Request at 7. 6 See id.at 2-3, 10. 7 See id.at 2-3 (“TETRA utilizes a highly efficient data transport mechanism allowing Short Data messages to be sent on the control circuit. Circuit mode data and IP packet data can be transmitted at up to 36kbits/s (gross) and 28kbits/s (net) for multi-slot operation. . . . Additionally, TETRA-based products come with built-in air interface encryption and optional end-to-end encryption features to protect the integrity of the voice/data mobile communications. Finally, TETRA allows for fast call set-up times of typically less than 300 ms which are essential for mission critical mobile communications. In sum, TETRA combines the advantages of two-way radio, mobile telephony, messaging and data in a way that is clear, fast and less expensive than other technologies.”). 8 See id.at 3. 9 See47 C.F.R. § 90.209(b)(5). 10 See47 C.F.R. § 90.210(b), (c), (g). The emission mask is the technical specification that limits the distribution of power of a radio transmitter as a function of frequency. The Development of Operational, Technical and Spectrum Requirements for Meeting Federal, State and Local Public Safety Agency Communication Requirements Through the Year 2010, First Report and Order and Third Notice of Proposed Rulemaking, WT Docket No. 96-86, 14 FCC Rcd 152, 213 n.337 (1998). The em…

Text truncated - open the document above for the full version.

The information contained in this document is proprietary to Selex ES S.p.A. This document and the information contained herein may not be copied, reproduced, used or disclosed in whole or in part in any form without the prior written consent of Selex ES S.p.A. © Copyright Selex ES S.p.A. - All Rights Reserved Company General Use Date: <03> <2015> Document type: Technical product paper TETRA Terminal Device VS4000 – Tune Up Informations TETRA Terminal Device VS4000 – Tune Up Informations TETRA Terminal Device VS4000 – Tune Up Informations Technical product paper ©Copyright Selex ES S.p.A. - All Rights Reserved Page 2 of 4 Company General Use FCC ID: X5YVS4000-806-870 Product Name: VS4000 806-870 Tune up Informations No tune up procedure is required by technician or user after the device has left the factory to match its specifications on the working frequency. The VS4000 device has no manual trimmers or adjustments that can be manually done on it acting directly on the device itself TETRA Terminal Device VS4000 – Tune Up Informations TETRA Terminal Device VS4000 – Tune Up Informations Technical product paper ©Copyright Selex ES S.p.A. - All Rights Reserved Page 3 of 4 Company General Use TETRA Terminal Device VS4000 – Tune Up Informations TETRA Terminal Device VS4000 – Tune Up Informations Technical product paper ©Copyright Selex ES S.p.A. - All Rights Reserved Page 4 of 4 Company General Use End document

www.nemko.com Nemko Italy S.p.A., Via del Carroccio 4, 20853, Biassono, Italy. Report number: 272549TRFMPE Apparatus: VS4000 806-870 Applicant: Selex ES S.p.A. Piazza Monte Grappa,4 -00195 Roma- Italy FCC ID: X5YVS4000-806-870 Test specification: MPE ASSESSMENT Federal Communications Commission Office of Engineering & Technology Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Reviewed by: 2014-11-12 Signature Date G. Curioni, Wireless/EMC Specialist Tested by: 2014/11/12 Signature Date D. Guarnone, Wireless/EMC Specialist Nemko S.p.A. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko S.p.A. accepts no responsibility for damages, if any suffered by any third party as a result of decisions made or actions based on this report. This report shall not be reproduced except in full without the written approval of the testing laboratory. www.nemko.com Nemko Italy S.p.A., Via del Carroccio 4, 20853, Biassono, Italy Report Number: 272549TRFMPE Specification: -- Page 2 of 23 Table of contents Section 1: Report summary ................................................................................................................... 3 Section 2: Equipment under test .......................................................................................................... 4 2.1 Identification of equipment under test (EUT) ............................................................................ 4 2.2 Accessories and support equipment ......................................................................................... 5 2.3 EUT description ........................................................................................................................ 6 2.4 Technical specifications of the EUT .......................................................................................... 6 2.5 EUT setup diagram................................................................................................................... 7 2.6 Operation of the EUT during testing ......................................................................................... 8 2.7 Modifications incorporated in the EUT ...................................................................................... 8 Section 3: Test conditions .................................................................................................................... 9 3.1 Deviations from laboratory tests procedures ............................................................................. 9 3.2 Test conditions, power source and ambient temperatures ........................................................ 9 3.3 Measurement uncertainty ......................................................................................................... 9 3.4 Test equipment ......................................................................................................................... 9 Section 4: Result summary ................................................................................................................. 10 4.1 MPE: Test results ................................................................................................................... 10 Appendix A: Test results ..................................................................................................................... 11 MPE CALCULATION ....................................................................................................................... 11 MPE CALCULATION, continue.. ...................................................................................................... 12 Nemko Italy S.p.A. Via del Carroccio 4, 20853 Biassono, Italy. Section 1: Report summary Report Number: 272549TRFMPE Specification: -- Page 3 of 23 Section 1: Report summary This report contains an assessment of apparatus against specifications based upon tests carried out on samples submitted at Nemko Italy SpA. Test specification: Federal Communications Commission Office of Engineering & Technology Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Compliance status: Complies Exclusions: None Non-compliances: None Report release history: Original release Test location: SELEX ES Via Albert Einstein, 35 Campi di Bisenzio Firenze, Italy. Registration number: 481407 (10 m Semi anechoic chamber) These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko Italy’s ISO/IEC 17025 accreditation. Nemko Italy SpA. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Italy SpA. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. Nemko Italy S.p.A. Via del Carroccio 4, 20853, Biassono, Italy Section 2: Equipment under test Report Number: 272549TRFMPE Specification: -- Page 4 of 23 Section 2: Equipment under test 2.1 Identification of equipment under test (EUT) The following information identifies the EUT under test: Type of equipment: Mobile R…

Text truncated - open the document above for the full version.

www.nemko.com Nemko Italy S.p.A., Via del Carroccio 4, 20853, Biassono, Italy. Report number: 272549TRFWL Apparatus: VS4000 806-870 Applicant: Selex ES S.p.A. Piazza Monte Grappa 4 - 00195 Roma- Italy FCC ID: X5YVS4000-806-870 Test specification: Title 47-Telecommunication Chapter I - Federal Communications Commission Subchapter D – Safety and special radio services Part 90 – Private land mobile services FCC 11-63 – Amendment of part 90 of the Commission Rule’s to permit Terrestrial Trunked Radio Tecnology (TETRA) − Subpart I – General technical standards Reviewed by: 2014-11-05 Signature Date G. Curioni, Wireless/EMC Specialist Tested by: Signature 2014-11-05 D. Guarnone, Wireless/EMC Specialist Date Nemko S.p.A. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko S.p.A. accepts no responsibility for damages, if any suffered by any third party as a result of decisions made or actions based on this report. This report shall not be reproduced except in full without the written approval of the testing laboratory. www.nemko.com Nemko Italy S.p.A., Via del Carroccio 4, 20853, Biassono, Italy Report Number: 272549TRFWL Specification: FCC 90 Page 2 of 49 Table of contents Section 1: Report summary ................................................................................................................... 3 Section 2: Equipment under test .......................................................................................................... 4 2.1 Identification of equipment under test (EUT) ............................................................................ 4 2.2 Accessories and support equipment ......................................................................................... 5 2.3 EUT description ........................................................................................................................ 6 2.4 Technical specifications of the EUT .......................................................................................... 6 2.5 EUT setup diagram................................................................................................................... 7 2.6 Operation of the EUT during testing ......................................................................................... 7 2.7 Modifications incorporated in the EUT ...................................................................................... 7 Section 3: Test conditions .................................................................................................................... 8 3.1 Deviations from laboratory tests procedures ............................................................................. 8 3.2 Test conditions, power source and ambient temperatures ........................................................ 8 3.3 Measurement uncertainty ......................................................................................................... 9 3.4 Test equipment ......................................................................................................................... 9 Section 4: Result summary ................................................................................................................. 10 4.1 FCC Part 90: Test results ....................................................................................................... 10 Appendix A: Test results ..................................................................................................................... 11 Clause 90.205 Output power ............................................................................................................ 11 Clause 90.207 Modulation characteristics ........................................................................................ 15 Clause 90.221 Adiacent Channel Power .......................................................................................... 16 Clause 90.210 Spurious emissions at the antenna terminal ............................................................. 24 Clause 90.210 Field strength of spurious radiation ........................................................................... 34 Clause 90.213 Frequency stability .................................................................................................... 44 Clause 90.219 Use of boosters ........................................................................................................ 48 Appendix B: Block diagrams of test set-ups ..................................................................................... 49 Nemko Italy S.p.A. Via del Carroccio 4, 20853 Biassono, Italy. Section 1: Report summary Report Number: 272549TRFWL Specification: FCC 90 Page 3 of 49 Section 1: Report summary This report contains an assessment of apparatus against specifications based upon tests carried out on samples submitted at Nemko Italy SpA. Test specification: FCC Part 90 Private land mobile services Subpart I – General technical standards Compliance status: Complies Exclusions: None Non-compliances: None Report release history: Original release Test location: Nemko Italy S.p.A. Via del Carroccio 4, 20853, Biassono, Italy. Registration number: 481407 (10 m Semi anechoic chamber) These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 90. Conducted measurements were performed in accordance with ANSI TIA-603-B-2002. Radiated tests were conducted is accordance with ANSI C63.4-2003. Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of …

Text truncated - open the document above for the full version.