X6HBS057RQBLUETOOTH HEADSET

When a call is coming, you can answer it with the ways as follows: BS057RQ Magnetic Bluetooth Headset User Manual Specifications The Headset Status Note: The two Phones mentioned follows will be called Phone A and B. In OFF MODE, press and hold MFB for 3 seconds, until you hear “Power on”, the indicator light turns blue for 1 second, then the headset will enter into ON MODE. The headset will be connected automatically(when the headset isn’t connect to any other bt headsets and the paring list is empty the headset will enter into pairing mode automatically) In ON MODE (except call state), press and hold MFB for 3 seconds, until you hear “Power off”, the indicator light turns red for 1 second, then the headset will enter into OFF MODE. Note: Headset isn’t connected with any devices within 20 minutes, it will automatically turn off. In PAIRED MODE, press and hold volume V- button, and say the voice tag as soon as you hear the short beep. (Ensure your phone supports voice dialing function, and you have recorded the voice tag into your phone. See the user guide of your phone for instructions.). Method 1: Press MFB once. Method 2: Adsorb the magnet together. Method 3: End the call with your phone. Shortly press MFB twice to hold on the current call and answer another one. Shortly press MFB twice to transfer the call from one to another. Shortly press MFB you can hang up the current call and answer another one. 4. Pairing Your Headset with a Bluetooth Phone 5.Answering a call 7. Rejecting a call 8.Voice prompt language switching When you are answering a call, there is another call coming: Structure Sketch 9.Voice Dialing Status No. Status Pairing Mode Not connected Standby Mode Charging Mode Low voltage state Call state Headset performance The headset can be searched, the indicator light flashes red and blue alternately. The headset is not connected with the device; blue light will flash once each 2 seconds. The headset is connected with the device, and not any other operations, blue light will flash once each 5 seconds. When in a call, the indicator light flashed blue once each 10 seconds. The indicator light turns red while being charged, and will turn blue automatically after being fully charged. When the battery’s voltage below 3.3V, the indicator light flashed red, the speaker prompt one time every once in a while. . Method 1: Method 2: Method 3: Method 4: 6.Ending a call Press MFB once. Separate the earphones, put in ear and answer(When megnet stay together) Adsorb the magnet earphone together and separate them slowly and answer(When enjoy music) Answer the call with your phone. Bluetooth Specification Bluetooth Profiles Supported Transmission Power Operation Range Frequency Range Battery Charging Voltage Charging Time Music Playing Time* Talk Time * Standby Time * Dimensions(mm) Weight V3.0 HSP.HFP. A2DP. AVRCP Class 2 Up to 10 Meters 2.402-2.480GHz Built-in Rechargeable 3.7V /60mAH Lithium Battery DC4.75-5.25V About 2 hours Up to 3.5 hours Up to 4 hours Up to 150 hours L38.5×W6.5×H10.5 About 16 g *The time mentioned above may vary due to user's operation mode and device settings. 1.Charging Your Headset Prior to using the headset for the first time or no use for a long time, please fully charge the battery. Approximately 2 hours are required to fully charge the headset. The indicator light turns red while being charged, and will turn blue automatically after being fully charged. When the headset is running out of battery, the indicator light will flash red (the headset will switch off automatically when the battery is drained). Please charge the headset as above steps in time to prolong the battery's useful life (Charging indication will be delayed for a few minutes if the headset has not been used for a long time or the battery is drained). 1.2. 1.3. 1.4. 1.1. Check the charging device is suit to the headset or not. Use only the supplied charger to charge the headset, if use other device may violate the validation or the maintenance article of this product and may cause danger. Do not attempt to force open the built-in battery as this could damage the headset. Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: 2.Turning on the Headset 3.Turning off Headset Ensure the headset is off, and the distance between your headset and phone is within 1 meter to activate the Bluetooth function on the phone. Press and hold MFB until the indicator light flashes blue and red alternately and could hear “pairing” as PAIRING MODE. Search Bluetooth devices (see the user guide of your phone for instructions). Select headset “MAGsmart Metallic” from the devices list of the phone. Enter paring code “0000”,press confirm and later you could hear “paired”, then could hear “your phone is connected”. If the pairing cannot be completed within 5 minutes after the PAIRING MODE has been activated, the headset will enter into the STANDBY MODE. Please repeat above steps to do the pairing again). Ensure there is no obstruction between your headset and phone and within effective distance, you can use the headset freely. Under the circumstance of power off, once you turn on the headset again it will connect the paired phone automatically within operation range. (see the user guide of your phone for instructions). 4.1. 10.1. 10.2. 10.3. 4.2. 4.3. 4.4. 4.5. 4.6. 4.7. 10.Two-call Handling 1 2 3 4 5 6 Press and hold MFB for 2 seconds to reject the call with beep ”dudu” from headset In PAIRED MODE, press and hole “Volume –“ for 2 seconds. And say the voice tag as soon as you hear voice promp”dudu” (Ensure your phone supports voice dialing function, and you have recorded the voice tag into your mobile. Please see the user guide of your mobile for more instructions.) You can end the call which you are answering with by below ways: Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you the freedom to make two calls at any time. Please read this user manual carefully…

Text truncated - open the document above for the full version.

Alpha Comm Enterprises, Inc. FCC Confidentiality Request To the FCC and FCC TCB handling this application for certification Pursuant to 47 CFR Section 0.459(a) & (b), we, (the applicant / grantee) Company name Alpha Comm Enterprises, Inc. Addresss 1500 Lakes Parkway, Suite B City Lawrenceville Georgia Country USA. request non-disclosure and confidential treatment for our certification under: Grantee Code Product Number FCC ID: X6H BS057RQ of the following materials submitted within this certification application: (please cross what is applicable, or add other documents) x Operational Description x Block Diagrams x Schematics Diagrams Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. We understand that pursuant to 47 CFR section 0.457(d)(1)(ii) disclosure of the applicant and all accompanying documentation will not be made before the date of the grant. Attestation: City and Country: Date: Name: (this must be a person) Function: Signature: (or official company stamp) Lawrenceville Georgia 2015/01/29 Frank Walter Piraino manager

Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 1 of 5 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. APPENDIX-A ATT-2015SZ0127013EUT Photo 1 Photo 2 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 2 of 5 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 3 Photo 4 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 3 of 5 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 5 Photo 6

FCC ID: X6HBS057RQ

Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 4 of 7 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 7 Photo 8 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 5 of 7 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 9 Photo 10 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 6 of 7 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 11 Photo 12 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ0127013 7 of 7 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 13 Photo 14

Shenzhen Asia Test Technology Co., Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +86)-0755-23284990 Email: [email protected] Http: www.att-lab.cn Report No. - Page ATT-2015SZ0127013F 1 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Shenzhen Asia Test Technology Co.,Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +86)-0755-23284990 Fax: +(86)-0755-23284990 http:// www.att-lab.cn FCC RADIO TEST REPORT FCC ID: X6HBS057RQ Product： BLUETOOTH HEADSET Trade Name： N/A Model Name： BS057RQ Serial Model： MAGsmart Metallic, BS058F Prepared for Alpha Comm Enterprises, Inc. 1500 Lakes Parkway, Suite B Lawrenceville Georgia USA. Prepared by Shenzhen Asia Test Technology Co.,Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +(86)-0755-23284990 Fax: +(86)-0755-23284990 Http: www.att-lab.cn Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ0127013F 2 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. TEST RESULT CERTIFICATION Applicant’s name............. Alpha Comm Enterprises, Inc. Address ............................. 1500 Lakes Parkway, Suite B Lawrenceville Georgia USA. Manufacture's Name........ GuangZhou U&I Electronic Technology Co.,Ltd Address ............................. 3rd Floor, Building G, FengSheng Industrial Zone, ShiBei Industrial Road, HuiJiang, Da Shi Street, PanYu District, Guangzhou, China Product description Product name ......................BLUETOOTH HEADSET Model and/or type reference .......................... BS057RQ Additional Model ................ MAGsmart Metallic, BS058F Standards......................... FCC Part15.247 Test procedure ..................... ANSI C63.10 This device described above has been tested by ATT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ATT, this document may be altered or revised by ATT, personal only, and shall be noted in the revision of the document. Date of Test........................................ Date (s) of performance of tests ......... Jan. 22 2015 ~Jan. 30 2015 Date of Issue....................................... Jan. 30 2015 Test Result........................................... Pass Tested by: Reviewed by: Approved by： Eric Wang Jerry You Jack yu Project Leader Laboratory Supervisor Technical Director Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ0127013F 3 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Table of Contents Page 1 . SUMMARY OF TEST RESULTS 6 1.1 TEST FACILITY 7 1.2 MEASUREMENT UNCERTAINTY 7 1.3 TEST ENVIRONMENT CONDITION 7 2 . GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF EUT 8 3 EUT CONFIGURATIONS 9 3.1 GENERAL CONFIGURATIONS 9 3.2 CUSTOMIZED CONFIGURATIONS 9 3.3 TEST ENVIRONMENTS 9 3.4 TEST SETUPS 9 3.5 TEST CONDITIONS 12 3.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 14 4 . EMC EMISSION TEST 15 4.1 CONDUCTED EMISSION MEASUREMENT 15 4.1.1 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 18 4.2.1 RADIATED EMISSION LIMITS 18 4.2.2 TEST PROCEDURE 19 4.2.3 DEVIATION FROM TEST STANDARD 19 4.2.4 TEST SETUP 20 4.2.5 EUT OPERATING CONDITIONS 21 4.2.6 TEST RESULTS (BELOW 30 MHZ) 22 4.2.7 TEST RESULTS (BETWEEN 30M – 1000 MHZ) 23 4.2.8 TEST RESULTS (ABOVE 1000 MHZ) 24 5 . NUMBER OF HOPPING CHANNEL 30 5.1 APPLIED PROCEDURES / LIMIT 30 5.1.1 TEST PROCEDURE 30 5.1.2 DEVIATION FROM STANDARD 30 Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ0127013F 4 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Table of Contents Page 5.1.3 TEST SETUP 30 5.1.4 EUT OPERATION CONDITIONS 30 5.1.5 TEST RESULTS 31 6 . AVERAGE TIME OF OCCUPANCY 32 6.1 APPLIED PROCEDURES / LIMIT 32 6.1.1 TEST PROCEDURE 32 6.1.2 TEST SETUP 32 6.1.3 TEST RESULTS 33 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 34 7.1 APPLIED PROCEDURES / LIMIT 34 7.1.1 TEST PROCEDURE 34 7.1.2 DEVIATION FROM STANDARD 34 7.1.3 TEST SETUP 34 7.1.4 EUT OPERATION CONDITIONS 34 7.1.5 TEST RESULTS 35 8 . BANDWIDTH TEST 37 8.1 APPLIED PROCEDURES / LIMIT 37 8.1.1 TEST PROCEDURE 37 8.1.2 DEVIATION FROM STANDARD 37 8.1.3 TEST SETUP 37 8.1.4 EUT OPERATION CONDITIONS 37 8.1.5 TEST RESULTS 38 9 . PEAK OUTPUT POWER TEST 40 9.1 APPLIED PROCEDURES / LIMIT 40 9.1.1 TEST PROCEDURE 40 9.1.2 DEVIATION FROM STANDARD 40 9.1.3 TEST SETUP…

Text truncated - open the document above for the full version.

Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ0127013F 49 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 12. EUT TEST PHOTO Radiated Measurement Photos Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ0127013F 50 of 50 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Conducted Measurement Photos