XCNDDW365Broadcom 3383G Wireless Cable Modem

1 Ubee DDW365.1 Wireless Cable Modem Safety and Installation Insert ◆ Federal Communication Commission Interference Statement • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ◆ FCC Radiation Exposure Statement: • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ◆ Safety Notices Read these instructions carefully before operating the device. It is important to be aware of these safety instructions. Install the device according to these instructions and keep this guide for future reference. • Do not use this device in a humid space, in the rain, or near splashing water. • Do not install during thunder or lightening storms. • Do not cover any ventilation openings in the device case. • Do not place the device near heat sources such as radiators or stoves. • Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. • Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. • The cable distribution system must be grounded in accordance with ANSI/NFPA 70 and the National Electrical Code (NEC), in particular section 802.93, 2 Grounding of the Outer Conductive Shield of a Coaxial Cable. ◆ Installation Instructions Use the following guidelines to install the device. Place the device near an outlet so the power supply can be plugged in directly to the wall outlet without an extension. Observe the maximum load of the electrical outlet. Use the power supply provided with the device. To install the device: Connect the device according to the following instructions and Figure 1. 1. Connect one end of the RF coaxial cable (not included) to the RF port on the device. Connect the other end to the cable wall outlet or a cable splitter. (Use a cable splitter, not included, to connect the device and a television to the same cable wall outlet.) Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. Figure 1 – Connection Diagram 2. Connect one end of the Ethernet cable (included) to one of the Ethernet ports (ETH1 – ETH4) on the device. Connect the other end to the Ethernet port on a PC. Note: Use Category 5e or 6 cables with RJ45 connectors when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds when the computer supports it. 3. Connect the power supply to the POWER port on the device. Plug the other end of the power supply into the AC wall outlet. Important: Use only the power supply provided with this device. 3 ◆ Additional Rear Panel Buttons • RESET button: Resets the device to the factory defaults. To reset, insert a small object into the reset opening and hold for more than 10 seconds. The device resets to factory defaults and reboots. Note: Not all parameters are reset to factory defaults. Refer to the user guide for more information. • USB Port: Provides one USB port with host controller. • WPS (on top of the device): Provides the Wi- Fi Protected Setup (WPS) method used to connect PIN-protected Wi-Fi equipment to this device. ◆ LEDs on Front Panel The following table describes LED behavior. LEDs are white. LED DESCRIPTION Power On when device has completed internal power ‐ on tests successfully. Blinks if power ‐ on test fails. US/DS Upstream/downstream connectivity. Blinks when ranging is in process, On when ranging is complete. Off when scanning for DS channel. Online On when device is online. Blinks when obtaining IP address and configuration file. Off when device is offline. WiFi On when Wi-Fi is enabled. Blinks when traffic is passed. Off when Wi-Fi is disabled. Figure 2 – Front Panel

Report No.: 120719E04 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 120719E04 Page 2 Report No.: 120719E04 Page 3

(Fig. 1) FCC ID: XCNDDW365 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

0.02012.04.25 U10C073.10 PTT Label 500.01500.005 Yanli Yu 1/1 "X": UL Factory ID, Foxconn printing NOTES: 1.Material: #50 Mylar + 25# PET(matte, printable) 2.Adhesive: Acrylic 3.Adhesive thickness : 50#Mylar: 0.024+/-0.003mm 25#PET: 0.018+/-0.003mm 4.Printing Color:Black 5.Background: White 6.Liner:Glassine release paper 7.Packaging Style: Reel 8.The part must be RoHS compliant Package style Vendor provide Foxconn printing Ubee Part No.: DDW365.1 Rating: 100-120VAC, 60Hz, 0.9A MAX Model name: DDW365 FCC ID: XCNDDW365 Factory ID: X Ubee Part No.: Rating: 100-120VAC, 60Hz, 0.9A MAX Model name: DDW365 FCC ID: XCNDDW365 0.1 N/A N/A 2012.08.10 delete Contains,add FCC ID:XCNDDW365,update Rating Cun

Report No.: 120719E04 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 120719E04 Page 2 Report No.: 120719E04 Page 3 Report No.: 120719E04 Page 4 Report No.: 120719E04 Page 5 Report No.: 120719E04 Page 6 Report No.: 120719E04 Page 7 Report No.: 120719E04 Page 8 Report No.: 120719E04 Page 9

FCC ID: XCNDDW365 Report No.: RF120719E04 Operational Description This device is a Broadcom 3383G Wireless Cable Modem, which operates in 2.4GHz band; the maximum data rate could be up to 450Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 450Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 12Vdc power supply. The antenna is PIFA antenna with HRS antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA120719E04 1 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 RF EXPOSURE REPORT REPORT NO.: SA120719E04 MODEL NO.: DDW365 FCC ID: XCNDDW365 RECEIVED: Jul. 20, 2012 TESTED: Sep. 14, 2012 ISSUED: Sep. 21, 2012 APPLICANT: Ubee Interactive Corp. ADDRESS: 10F-1, No. 5 Taiyuen 1st St. Jhubei City Hsinchu County 302, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA120719E04 2 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA120719E04 3 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA120719E04 Original release Sep. 21, 2012 Report No.: SA120719E04 4 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 1. CERTIFICATION PRODUCT: Broadcom 3383G Wireless Cable Modem BRAND NAME: Ubee MODEL NO.: DDW365 TEST SAMPLE: R&D SAMPLE APPLICANT: Ubee Interactive Corp. TESTED DATE: Sep. 14, 2012 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: DDW365) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Sep. 21, 2012 ( Elsie Hsu, Specialist ) APPROVED BY : , DATE: Sep. 21, 2012 ( May Chen, Deputy Manager ) Report No.: SA120719E04 5 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA120719E04 6 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA110718E01 dated Aug. 19, 2011 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 320.537 2.48 20 0.11288 1.00 ---END---

Report No.: RF120719E04 R1 1 of 54 Report Format Version 5.0.0 Cancels and replaces the report No.: RF120719E04 dated Sep 21, 2012. FCC TEST REPORT REPORT NO.: RF120719E04 R1 MODEL NO.: DDW365 FCC ID: XCNDDW365 RECEIVED: Jul. 20, 2012 TESTED: Jul. 31 to Sep. 18, 2012 ISSUED: Sep. 25, 2012 APPLICANT: Ubee Interactive Corp. ADDRESS: 10F-1, No. 5 Taiyuen 1st St. Jhubei City Hsinchu County 302, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF120719E04 R1 2 of 54 Report Format Version 5.0.0 Cancels and replaces the report No.: RF120719E04 dated Sep 21, 2012. Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION .................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 6 3. GENERAL INFORMATION ..................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 7 3.2 DESCRIPTION OF TEST MODES ......................................................................... 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 12 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 13 3.5 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 14 4. TEST TYPES AND RESULTS .............................................................................. 15 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 15 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 15 4.1.2 TEST INSTRUMENTS .......................................................................................... 15 4.1.3 TEST PROCEDURES .......................................................................................... 16 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 16 4.1.5 TEST SETUP ....................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 17 4.1.7 TEST RESULTS ................................................................................................... 18 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 20 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 20 4.2.2 TEST INSTRUMENTS .......................................................................................... 21 4.2.3 TEST PROCEDURES .......................................................................................... 22 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 22 4.2.5 TEST SETUP ....................................................................................................... 23 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 23 4.2.7 TEST RESULTS ................................................................................................... 24 4.3 6dB BANDWIDTH MEASUREMENT .................................................................... 37 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 37 4.3.2 TEST INSTRUMENTS .......................................................................................... 37 4.3.3 TEST PROCEDURE ............................................................................................. 37 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 37 4.3.5 TEST SETUP .........................................................…

Text truncated - open the document above for the full version.

Report No.: 120719E04 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 120719E04 RADIATED EMISSION TEST