XCNUBC1330Docsis3.1 advance WiFi 6E Voice Gateway

UBC1330AA00 DOCSIS 3.1 Advanced WiFi 6E Voice Gateway Quick Installation Guide www.ubeeinteractive.com D3.1 WiFi 6 eMTA UBC1330AA00 Quick Installation Guide Grounding the Device: Install the cable modem to include grounding the coaxial cable to the earth as close as practical to the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. This unit requires a 100-240V, 50/60Hz power adapter. Power adapter must be keyed for proper polarization, and must be fully inserted to contact the back of the power connector port to ensure snug connection. Do NOT use any other power adapter. Disconnecting the Device: If the cable modem becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. Temperature and Altitude: Install the device in a location not to exceed the maximum temperature of 104 Fahrenheit (40 Celsius). Regular operating altitude is 2000 m, and maximum operating altitude is 4500 m. • SAFETY NOTICES • PREPARING FOR INSTALLATION ✓ Locate the RF (coaxial) cable connector on the wall. ✓ Verify the power outlet is working and is wired correctly. Place your cable modem within a proper distance from the outlet. 2.Connect an Ethernet cable (supplied) to one of the ETHERNET ports on the back panel of the modem and connect the other end to the Ethernet port of a PC. Use a Category 5e or Category 6 Ethernet cable with RJ-45 connectors to ensure Gigabit Ethernet speeds (when the computer supports it). 3.Connect an RJ-11 phone cable (not supplied) to the TEL 1 port on the modem (when provisioned for voice service as specified by the service provider), and connect the other end to the phone port of the telephone. If voice service is not provisioned through the service provider, telephone service is not available. 4.Connect the power adapter (supplied) to the POWER port. Connect the other end to a power outlet. 1 UBC1330AA00 RJ-45 RJ-11 Cable/RF Device must be installed vertically to obtain optimum wireless performance. Connect a PC or Ethernet enabled device (wireless switch or router). A PC should be connected for initial device installation and configuration. 2 1 3 4 1.Connect the coaxial cable (not supplied) to the CABLE connector on the rear panel of the modem and connect the other end to the cable wall outlet. Do not bend or over tighten the cables, as this may strain the connector and cause damage. To connect a modem and a television to the same wall outlet, you must use a cable line splitter (not included). • INSTALLING THE MODEM • DEVICE WALL MOUNT INSTRUCTIONS You can mount the UBC1330AA00 on a wall using the 2 mounting brackets on the side of the device. Two round or pan head screws are recommended. See the figure below for measurements. www.ubeeinteractive.com 2 UBC1330AA00 Quick Installation Guide NOTE to CATV SYSTEM INSTALLER: This reminder is provided to call the CATV systems installer's attention to section 820-93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. Note: The screws should protrude from the wall so you can fit the device between the head of the screws and the wall. If you install the screws in drywall, use hollow wall anchors to ensure the unit does not pull away from the wall due to prolonged strain from the cable and power connectors. 2.Mount the device on the wall. To mount the device on a wall: 1.Install the 2 screws horizontally on the wall 161.8 mm (6.37 inches apart. 161.8mm (6.37 inches) D LabelSize in Millimeters (mm) A7.2 +/- 0.5 B2.6 +/- 0.15 C19.0 +/- 1.2 D3.5 - 4.5 • UNDERSTANDING DEVICE CONNECTIONS AND BUTTONS The rear and front panels of the UBC1330AA00 have the following connections and buttons: RESET: Use to reset the device. Take a small object like the end of a paper clip and insert it into the RESET opening. To power cycle the device, hold for less than 5 seconds. To reset to factory default settings, hold for more than 20 seconds. The UBC1330AA00 will reset and reboot. WARNING: Resetting factory defaults will erase ANY and ALL settings that you have made and will restore the device to factory default settings. ETHERNET 2.5G: Use to connect to a wireless router at 2.5Gbps speed using an RJ-45 Ethernet cable. This port has 2 LEDs to indicate its status. See the LED Behavior section on the next page for details. ETHERNET 1G 1-3: Use to connect to Ethernet-enabled devices such as computers or gaming consoles at 1Gbps speeds using RJ45 Ethernet cables. Each Ethernet port has two LEDs to indicate its status. See the LED Behavior section on the next page for details. CABLE: Use to connect to the coaxial cable from your Internet service provider. TEL 1 - TEL 2: Use to connect analog telephones to the device. POWER: Use to connect to the power adapter. Plug the other end into the wall power outlet. BATT: Use to connect to an optional external battery. WPS: Located on the bottom of the front panel of the device, it is used for the Wi-Fi Protected Setup (WPS) method to connect a PIN-protected Wi-Fi device to the cable modem. Push the button for less than 5 seconds to initiate WPS pairing activation. • BASIC MODEM INFORMATION www.ubeeinteractive.com 3 UBC1330AA00 Quick Installation Guide Example of Cable RF MAC Address 00:71:CC:8E:54:C7 Firmware Version 12.13.1002.uni-r16.03. Compatibility DOCSIS 3.1/3.0/2.0/1.0 certified Ethernet 10/100/1000 Mbps Wireless 802.11a/b/g/n/ac/ax WiFi 6E Local Web UI Access http://192.168.100.1 or http://192.168.0.1 Modem Web Login (web UI) Login: admin Password: Randomly generated string, 12 characters in length. Found on the device label. This is your login password. Encryption WPA2-PSK with AES …

Text truncated - open the document above for the full version.

Reference No.:BEMV-WTW-P22070474_EXT Page 1/7 CONSTRUCTION PHOTOS OF EUT Reference No.:BEMV-WTW-P22070474_EXT Page 2/7 Reference No.:BEMV-WTW-P22070474_EXT Page 3/7 Reference No.:BEMV-WTW-P22070474_EXT Page 4/7 Reference No.:BEMV-WTW-P22070474_EXT Page 5/7 Reference No.:BEMV-WTW-P22070474_EXT Page 6/7 Adapter (Brand: I.T.E, Model: MU48AY120400-A1) Reference No.:BEMV-WTW-P22070474_EXT Page 7/7 RJ 45 Cable

(Fig. 1) FCC ID: XCNUBC1330 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label (Fig. 1) FCC ID: XCNUBC1330

Reference No.:BEMV-WTW-P22070474_INT Page 1/24 CONSTRUCTION PHOTOS OF EUT Reference No.:BEMV-WTW-P22070474_INT Page 2/24 Reference No.:BEMV-WTW-P22070474_INT Page 3/24 Reference No.:BEMV-WTW-P22070474_INT Page 4/24 221220_PM叫我加這張 Reference No.:BEMV-WTW-P22070474_INT Page 5/24 Reference No.:BEMV-WTW-P22070474_INT Page 6/24 Reference No.:BEMV-WTW-P22070474_INT Page 7/24 Reference No.:BEMV-WTW-P22070474_INT Page 8/24 Reference No.:BEMV-WTW-P22070474_INT Page 9/24 Reference No.:BEMV-WTW-P22070474_INT Page 10/24 Reference No.:BEMV-WTW-P22070474_INT Page 11/24 Reference No.:BEMV-WTW-P22070474_INT Page 12/24 Reference No.:BEMV-WTW-P22070474_INT Page 13/24 Reference No.:BEMV-WTW-P22070474_INT Page 14/24 Reference No.:BEMV-WTW-P22070474_INT Page 15/24 Reference No.:BEMV-WTW-P22070474_INT Page 16/24 Reference No.:BEMV-WTW-P22070474_INT Page 17/24 Reference No.:BEMV-WTW-P22070474_INT Page 18/24

Reference No.:BEMV-WTW-P22070474_INT Page 19/24 Reference No.:BEMV-WTW-P22070474_INT Page 20/24 Reference No.:BEMV-WTW-P22070474_INT Page 21/24 Reference No.:BEMV-WTW-P22070474_INT Page 22/24 Reference No.:BEMV-WTW-P22070474_INT Page 23/24 Reference No.:BEMV-WTW-P22070474_INT Page 24/24

Report No.: MFBEMV-WTW-P22070474 Page No. 1 / 11 Report Format Version: 7.1.0 RF EXPOSURE REPORT CERTIFICATE OF CONFORMITY FCC Rule Part: FCC Part 2 (Section 2.1091) Report No.: MFBEMV-WTW-P22070474 FCC ID: XCNUBC1330 Product: Docsis3.1 advance WiFi 6E Voice Gateway Brand: Ubee Model No.: UBC1330 Received Date: 2022/8/4 Test Date: 2022/11/8 Issued Date: 2022/12/14 Applicant: Ubee Interactive Holding Corp. Taiwan Branch Address: 10F-1, No.5, Taiyuan 1st St. Jhubei Hsinchu, 302, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 Approved by: , Date: 2022/12/14 May Chen / Manager This test report consists of 11 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Vivian Huang / Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBEMV-WTW-P22070474 Page No. 2 / 11 Report Format Version: 7.1.0 Table of Contents Release Control Record ....................................................................................................................................................... 3 1 Certificate .................................................................................................................................................................... 4 2 Applicable RF Exposure Limit .................................................................................................................................. 5 2.1 RF Exposure ............................................................................................................................................................. 6 3 Test Results ................................................................................................................................................................ 8 3.1 RF Exposure ............................................................................................................................................................. 8 4 Conclusion ................................................................................................................................................................ 10 5 Information of the Testing Laboratories ................................................................................................................ 11 Report No.: MFBEMV-WTW-P22070474 Page No. 3 / 11 Report Format Version: 7.1.0 Release Control Record Issue No. Description Date Issued MFBEMV-WTW-P22070474 Original release. 2022/12/14 Report No.: MFBEMV-WTW-P22070474 Page No. 4 / 11 Report Format Version: 7.1.0 1 Certificate Product: Docsis3.1 advance WiFi 6E Voice Gateway Brand: Ubee Test Model: UBC1330 Sample Status: Engineering sample Applicant: Ubee Interactive Holding Corp. Taiwan Branch Test Date: 2022/11/8 FCC Rule Part: FCC Part 2 (Section 2.1091) Standard: KDB 447498 D04 Interim General RF Exposure Guidance v01 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Report No.: MFBEMV-WTW-P22070474 Page No. 5 / 11 Report Format Version: 7.1.0 2 Applicable RF Exposure Limit § 1.1310 Radiofrequency radiation exposure limits. (a) Specific absorption rate (SAR) shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in § 1.1307(b) of this part within the frequency range of 100 kHz to 6 GHz (inclusive). (b) The SAR limits for occupational/controlled exposure are 0.4 W/kg, as averaged over the whole body, and a peak spatialaverage SAR of 8 W/kg, averaged over any 1 gram of tissue (defined as a tissue volume in the shape of a cube). Excep…

Text truncated - open the document above for the full version.

Page 1 of 73 Antenna Design Ubee U10C163 V2.09 Document Number 1 st Released Date 08/03/2021 Test date 05/31/2022 Test personnel Wei Review by Yuan Page 2 of 73 Revised History Date Version Revised Record 08/03/2021 1.01 Antenna simulation 08/10/2021 1.02 Improve isolation to -25 dB 08/30/2021 1.03 Machine sample test.(Sku1. Large heat sink) 08/30/2021 1.04 Machine sample test.(Sku2. Small heat sink) 09/29/2021 1.05 PCB add foolproof design, update S11 10/13/2021 1.06 Ant4 & Ant6 layout changed, update isolation & radiation pattern. 11/05/2021 2.07 Antenna test with pilot run sample 11/26/2021 2.08 Antenna fine tune for new specification 04/11/2022 2.08_1 Update cable length and cable loss 04/19/2022 2.08_2 Update cable length and cable loss(add exposed cable length) 05/31/2022 2.09 Update isolation test mathod Page 3 of 73 Specification Rough description Dual Band 2G/5G antenna*4 , WIFI 6E antenna *4 Item Initial Specification Dimensions None Impedance 50Ω Test environment Spectrum Freq. Range WIFI Dualband: 2.4~2.5GHz & 5.05~5.825GHz WIFI 6E: 5.925GHz ~ 7.125GHz Antenna type Gain 2.4G < 3.5 dBi , 5G < 4 dBi , 6G < 3.5dBi VSWR <1.92 Radiation Polarization Linear HPBW / H None HPBW / E None Rad. efficiency None Connector type I- Pex Cable type 1.13 Cable length None Isolation <-20 dB Page 6 of 73 S-parameter test results 2.1 S11 test results 2.1.1 Ant_1 (Dual band) 2.1.2 Ant_2 (WIFI 6E) Page 7 of 73 2.1.3 Ant_3 (WIFI 6E) 2.1.4 Ant_4 (Dual band) Page 8 of 73 2.1.5 Ant_5 (WIFI 6E) 2.1.6 Ant_6 (Dual band) Page 9 of 73 2.1.7 Ant_7 (WIFI 6E) 2.1.8 Ant_8 (Dual band) Page 10 of 73 2.2 Isolation test results 2.2.1 Ant_1 to Ant_2 2.2.2 Ant_1 to Ant_3 Page 11 of 73 2.2.3 Ant_1 to Ant_4 2.2.4 Ant_1 to Ant_5 Page 12 of 73 2.2.5 Ant_1 to Ant_6 2.2.6 Ant_1 to Ant_7 Page 13 of 73 2.2.7 Ant_1 to Ant_8 2.2.8 Ant_2 to Ant_3 Page 14 of 73 2.2.9 Ant_2 to Ant_4 2.2.10 Ant_2 to Ant_5 Page 15 of 73 2.2.11 Ant_2 to Ant_6 2.2.12 Ant_2 to Ant_7 Page 16 of 73 2.2.13 Ant_2 to Ant_8 2.2.14 Ant_3 to Ant_4 Page 17 of 73 2.2.15 Ant_3 to Ant_5 2.2.16 Ant_3 to Ant_6 Page 18 of 73 2.2.17 Ant_3 to Ant_7 2.2.18 Ant_3 to Ant_8 Page 19 of 73 2.2.19 Ant_4 to Ant_5 2.2.20 Ant_4 to Ant_6 Page 20 of 73 2.2.21 Ant_4 to Ant_7 2.2.22 Ant_4 to Ant_8 Page 21 of 73 2.2.23 Ant_5 to Ant_6 2.2.24 Ant_5 to Ant_7 Page 22 of 73 2.2.25 Ant_5 to Ant_8 2.2.26 Ant_6 to Ant_7 Page 23 of 73 2.2.27 Ant_6 to Ant_8 2.2.28 Ant_7 to Ant_8 Page 24 of 73 3.Gain & Patterns test results 3.1 Lab information ■ ETS AMS-8500 Full-Size Rectangular Serial No.: Euroshield-CT000114-1039 Date: 2009-11-13 ■ EMQuest EMQ-100 Pattern Measurement Software Page 26 of 73 4.2 2D patterns 4.2.1 Ant_1 (Dual band) X Z Y Z Y X Page 27 of 73 Page 28 of 73 Page 29 of 73 4.2.2 Ant_2 (Wi-Fi 6E) Page 30 of 73 Page 31 of 73 Page 32 of 73 Page 33 of 73 4.2.3 Ant_3 (Wi-Fi 6E) Page 34 of 73 Page 35 of 73 Page 36 of 73 Page 37 of 73 4.2.4 Ant_4 (Dual band) Page 38 of 73 Page 39 of 73 4.2.5 Ant_5 ( Wi-Fi 6E) Page 40 of 73 Page 41 of 73 Page 42 of 73 Page 43 of 73 4.2.6 Ant_6 (Dual band) Page 44 of 73 Page 45 of 73 4.2.7 Ant_7 (Wi-Fi 6E) Page 46 of 73 Page 47 of 73 Page 48 of 73 Page 49 of 73 4.2.8 Ant_8 (Dual band) Page 50 of 73 Page 51 of 73 5.Summary 5.1 Return Loss WIFI Dual band Frequency Ant_1 (dB) Ant_4 (dB) Ant_6 (dB) Ant_8 (dB) 2400 MHz 12 13 14 11 2450 MHz 12 13 15 13 2500 MHz 11 13 17 11 5050 MHz 16 16 14 15 5150 MHz 14 20 15 18 5350 MHz 18 30 16 21 5725 MHz 17 16 17 16 5825 MHz 18 19 14 17 WIFI 6E Frequency Ant_2 (dB) Ant_3 (dB) Ant_5 (dB) Ant_7 (dB) 5925 MHz 12 15 18 13 6125 MHz 20 16 26 17 6325 MHz 16 33 20 24 6525 MHz 12 19 14 22 6725 MHz 17 15 12 19 6925 MHz 24 14 14 24 7125 MHz 14 27 16 16 Page 52 of 73 5.2 Isolation Frequency Ant_1 & Ant_2 Ant_1 & Ant_3 Ant_1 & Ant_4 Ant_1 & Ant_5 Ant_1 & Ant_6 Ant_1 & Ant_7 Ant_1 & Ant_8 2G Isolation(dB) 31.0 35.9 22.5 38.5 28.7 38.5 38.7 5G Isolation(dB) 29.0 28.6 28.2 26.7 31.4 28.0 36.8 6G Isolation(dB) 31.5 29.8 - 31.3 - 37.7 - Frequency Ant_2 & Ant_3 Ant_2 & Ant_4 Ant_2 & Ant_5 Ant_2 & Ant_6 Ant_2 & Ant_7 Ant_2 & Ant_8 2G Isolation(dB) - 27.6 - 28.5 - 34.9 5G Isolation(dB) - 22.0 - 32.0 - 42.0 6G Isolation(dB) 22.0 23.9 27.0 37.9 34.0 42.0 Frequency Ant_3 & Ant_4 Ant_3 & Ant_5 Ant_3 & Ant_6 Ant_3 & Ant_7 Ant_3 & Ant_8 2G Isolation(dB) 26.6 - 29.5 - 37.3 5G Isolation(dB) 35.0 - 31.0 - 37.0 6G Isolation(dB) 32.0 26.0 34.0 29.0 32.0 Frequency Ant_4 & Ant_5 Ant_4 & Ant_6 Ant_4 & Ant_7 Ant_4 & Ant_8 2G Isolation(dB) 25.7 21.6 27.9 35.3 5G Isolation(dB) 25.0 25.0 27.0 35.0 6G Isolation(dB) 30.0 - 27.0 - Frequency Ant_5 & Ant_6 Ant_5 & Ant_7 Ant_5 & Ant_8 2G Isolation(dB) 21.4 - 35.5 5G Isolation(dB) 31.0 - 33.0 6G Isolation(dB) 26.5 27.0 32.0 Frequency Ant_6 & Ant_7 Ant_6 & Ant_8 Ant_7 & Ant_8 2G Isolation(dB) 26.8 33.0 29.5 5G Isolation(dB) 24.1 30.0 25.0 6G Isolation(dB) 30.0 - 25.0 Page 53 of 73 5.3 3D total Peak Gain & Efficiency WIFI Dual Band Frequency Ant_1 Ant_4 Ant_6 Ant_8 Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) 2400 MHz 3.12 71 3.39 74 3.49 75 3.31 81 2450 MHz 3.21 72 3.16 72 3.26 75 3.39 80 2500 MHz 3.48 70 2.73 71 3.31 75 3.33 75 5050 MHz 3.40 73 3.97 73 3.96 77 3.79 78 5150 MHz 3.05 72 3.79 71 3.55 75 3.47 75 5350 MHz 3.48 73 3.68 72 3.89 74 3.94 75 5725 MHz 3.31 70 3.67 70 3.62 76 3.93 76 5825 MHz 3.41 70 3.96 70 3.82 73 3.93 76 WIFI 6E Frequency Ant_2 Ant_3 Ant_5 Ant_7 Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) 5925 MHz 3.20 72 3.28 74 3.48 77 3.17 76 6000 MHz 3.24 70 3.26 71 3.29 76 3.25 75 6125 MHz 3.41 73 3.30 71 3.35 72 3.26 71 6225 MHz 3.45 73 3.40 73 3.19 73 3.47 71 6325 MHz 3.34 74 3.43 74 3.39 74 3.37 72 6425 MHz 3.30 73 3.33 75 3.46 74 3.37 74 6525 MHz 3.43 72 3.12 72 3.50 73 3.48 74 6625 MHz 3.45 71 3.43 74 3.31 72 3.33 72 6725 MHz 3.17 74 3.18 74 3.42 73 3.35 72 6825 MHz 3.30 75 3.37 75 3.30 75 3.11 74 6925 MHz 3.14 74 3.13 74 3.18 73 3.41 73 7000 MH…

Text truncated - open the document above for the full version.

Report No.: RFBEMV-WTW-P22070474-2 Page No. 1 / 226 Report Format Version: 7.1.0 TEST REPORT CERTIFICATE OF CONFORMITY Standard: 47 CFR FCC Part 15, Subpart E (Section 15.407) Report No.: RFBEMV-WTW-P22070474-2 FCC ID: XCNUBC1330 Product: Docsis3.1 advance WiFi 6E Voice Gateway Brand: Ubee Model No.: UBC1330 Received Date: 2022/8/4 Test Date: 2022/8/17 ~ 2022/12/1 Issued Date: 2022/12/14 Applicant: Ubee Interactive Holding Corp. Taiwan Branch Address: 10F-1, No.5, Taiyuan 1st St. Jhubei Hsinchu, 302, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 Approved by: , Date:2022/12/14 May Chen / Manager This test report consists of 226 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Vivian Huang / Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBEMV-WTW-P22070474-2 Page No. 2 / 226 Report Format Version: 7.1.0 Table of Contents Release Control Record ....................................................................................................................................................... 4 1 Certificate .................................................................................................................................................................... 5 2 Summary of Test Results .......................................................................................................................................... 6 2.1 Measurement Uncertainty ........................................................................................................................................ 6 2.2 Supplementary Information ...................................................................................................................................... 6 3 General Information ................................................................................................................................................... 7 3.1 General Description of EUT ..................................................................................................................................... 7 3.2 Antenna Description of EUT ..................................................................................................................................... 8 3.3 Channel List .............................................................................................................................................................. 9 3.4 Test Mode Applicability and Tested Channel Detail ................................................................................................ 11 3.5 Duty Cycle of Test Signal........................................................................................................................................ 14 3.6 Test Program Used and Operation Descriptions .................................................................................................... 18 3.7 Connection Diagram of EUT and Peripheral Devices ............................................................................................ 18 3.8 Configuration of Peripheral Devices and Cable Connections ................................................................................ 19 4 Test Instruments ...................................................................................................................................................... 20 4.1 RF Output Power .................................................................................................................................................... 20 4.2 Power Spectral Density .......................................................................................................................................... 20 4.3 Emission Bandwidth ...............................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBEMV-WTW-P22070474-2 Page No. 98 / 226 Report Format Version: 7.1.0 Plots of Injected signal (AWGN) level 802.11ax (HE20) / CH1 802.11ax (HE160) / CH15(Low Edge) 802.11ax (HE160) / CH15(Middle) 802.11ax (HE160) / CH15(High Edge) Plots of EUT ceased transmission in the time domain 802.11ax (HE20) / CH1 802.11ax (HE160) / CH15(Low Edge) 802.11ax (HE160) / CH15(Middle) 802.11ax (HE160) / CH15(High Edge) Injected Interference signal at 1 sec Injected Interference signal at 1 sec Injected Interference signal at 1 sec Injected Interference signal at 1 sec Report No.: RFBEMV-WTW-P22070474-2 Page No. 99 / 226 Report Format Version: 7.1.0 For U-NII-6 Contention Based Protocol Measurement Operation Mode Channel Bandwidth (MHz) Channel Number Channel Freq. (MHz) Injected Signal (AWGN) Antenna Gain (dBi) Path Loss (dB) (Note 2) Adjusted Power (dBm) Detection Limit EUT TX Status Freq. (MHz) Power (dBm) 802.11ax 20 97 6435 6435 -62.37 3.33 0 -65.7 -62 OFF -62.87 3.33 0 -66.2 -62 Minimal -78.67 3.33 0 -82 -62 ON 160 111 6505 6430 -62.08 3.33 0 -65.41 -62 OFF -62.58 3.33 0 -65.91 -62 Minimal -78.67 3.33 0 -82 -62 ON 6505 -58.83 3.33 0 -62.16 -62 OFF -59.33 3.33 0 -62.66 -62 Minimal -78.67 3.33 0 -82 -62 ON 6580 -60.85 3.43 0 -64.28 -62 OFF -61.35 3.43 0 -64.78 -62 Minimal -78.67 3.43 0 -82.1 -62 ON Notes: 1. Adjusted Power (dBm) = Injected Signal (AWGN) Power (dBm) - Antenna Gain (dBi) + Path Loss (dB) 2. Antenna gain values include all the applicable path losses. 3. After evaluation, only the Chain 2 was chosen for test and presented in the test report. Contention Based Protocol Detection Probability Operation Mode Channel Bandwidth (MHz) AWGN Signal Freq. (MHz) #01 #02#03#04#05#06#07#08#09#10 Detection Probability Detection Limit Test Result 802.11ax 20 6435 v v vvvvvvvv100% 90% Pass 160 6430 v v vvvvvvvv100% 90% Pass 6505 v v vvvvvvvv100% 90% Pass 6580 v v vvxvvvvv 90% 90% Pass Plots of EUT Tx waveform 802.11ax (HE20) / CH97 802.11ax (HE160) / CH111 Report No.: RFBEMV-WTW-P22070474-2 Page No. 100 / 226 Report Format Version: 7.1.0 Plots of Injected signal (AWGN) level 802.11ax (HE20) / CH97 802.11ax (HE160) / CH111(Low Edge) 802.11ax (HE160) / CH111(Middle) 802.11ax (HE160) / CH111(High Edge) Plots of EUT ceased transmission in the time domain 802.11ax (HE20) / CH97 802.11ax (HE160) / CH111(Low Edge) 802.11ax (HE160) / CH111(Middle) 802.11ax (HE160) / CH111(High Edge) Injected Interference signal at 1 sec Injected Interference signal at 1 sec Injected Interference signal at 1 sec Injected Interference signal at 1 sec Report No.: RFBEMV-WTW-P22070474-2 Page No. 101 / 226 Report Format Version: 7.1.0 For U-NII-7 Contention Based Protocol Measurement Operation Mode Channel Bandwidth (MHz) Channel Number Channel Freq. (MHz) Injected Signal (AWGN) Antenna Gain (dBi) Path Loss (dB) (Note 2) Adjusted Power (dBm) Detection Limit EUT TX Status Freq. (MHz) Power (dBm) 802.11ax 20 129 6595 6595 -61.12 3.43 0 -64.55 -62 OFF -61.62 3.43 0 -65.05 -62 Minimal -78.57 3.43 0 -82 -62 ON 160 143 6665 6590 -60.25 3.43 0 -63.68 -62 OFF -60.75 3.43 0 -64.18 -62 Minimal -78.57 3.43 0 -82 -62 ON 6665 -61.22 3.43 0 -64.65 -62 OFF -61.72 3.43 0 -65.15 -62 Minimal -78.57 3.43 0 -82 -62 ON 6740 -60.33 3.43 0 -63.76 -62 OFF -60.83 3.43 0 -64.26 -62 Minimal -78.57 3.43 0 -82 -62 ON Notes: 1. Adjusted Power (dBm) = Injected Signal (AWGN) Power (dBm) - Antenna Gain (dBi) + Path Loss (dB) 2. Antenna gain values include all the applicable path losses. 3. After evaluation, only the Chain 2 was chosen for test and presented in the test report. Contention Based Protocol Detection Probability Operation Mode Channel Bandwidth (MHz) AWGN Signal Freq. (MHz) #01 #02#03#04#05#06#07#08#09#10 Detection Probability Detection Limit Test Result 802.11ax 20 6595 v v vvvvvvvx 90% 90% Pass 160 6590 v v vvvvvvvv100% 90% Pass 6665 v v vvvvvvvv100% 90% Pass 6740 v v vvvvvxvv 90% 90% Pass Plots of EUT Tx waveform 802.11ax (HE20) / CH129 802.11ax (HE160) / CH143 Report No.: RFBEMV-WTW-P22070474-2 Page No. 102 / 226 Report Format Version: 7.1.0 Plots of Injected signal (AWGN) level 802.11ax (HE20) / CH129 802.11ax (HE160) / CH143(Low Edge) 802.11ax (HE160) / CH143(Middle) 802.11ax (HE160) / CH143(High Edge) Plots of EUT ceased …

Text truncated - open the document above for the full version.