XCNUBN2310GPON

UBN2310 GPON Safety Manual • DECLARATION OF CONFORMITY UBN2310 Safety Manual • SAFETY NOTICES IMPORTANT: Read these instructions before using the device. • Do not use this device in a humid space, in the rain or near splashing water. • Do not install during thunder or lightning storms. • For operation within the 5.15~5.25GHz and 5.47~5.725GHz frequency ranges, this device is restricted to indoor environments. • Do not cover any ventilation openings in the device housing. • Do not place the device near heat sources such as radiators or stoves. • Clean the device with a clean, dry cloth. Do not use liquid or chemical cleaners. • Disconnecting the device: If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. • The device should be installed in a location not to exceed the maximum temperature of 40° Celsius (104° Fahrenheit). • Keep the device away from children and pets. • This equipment is not suitable for use in locations where children are likely to be present. • Do not modify or attempt to disassemble the device. Use it only according to the instructions. • Place the device on a cool surface. Failure to do so may result in overheating which can cause significant damage. • Product information is located on the bottom panel of the apparatus. • Do not dispose of the device in a trash container. Please recycle. • This product is intended to be supplied by a Listed Power Adapter or DC power source marked “L.P.S." (or "Limited Power Source"), rated 12 Vdc, 2A minimum, Tma = 40 degree C minimum. If need f u r t h e r a s s i s t a n ce , p l e a s e co n t a c t H O N L I N Technology Co., Ltd. for further information.” • Use only a Laser Class 1 optical transceiver: •CLASS 1 LASER PRODUCT & ”IEC 60825-1:2014” •Complies with FDA performance standards for laser products except for conformance with IEC 60825-1 Ed. 3, as described in Laser Notice No. 56, dated May 8, 2019. •Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Manufacturer: Ubee Interactive Holding Corp. Taiwan Branch 10F-1, No. 5 Taiyuan 1st St. Jhubei City, Hsinchu County 302, Taiwan Power Outlet 4 UBN2310 Safety Manual • INSTALLATION INSTRUCTIONS 1.Plug one end of a fiber optic cable into the green PON (passive optical network) port on the rear panel of the device. The connector will “click” into place when properly installed. Plug the other end into the optical wall outlet. WARNING: Do not look directly into the optical cable end or directly into the PON port as eye injury may occur. 2.For telephone service, connect one end of another RJ-11 phone cable (not included) to one of the grey PHONE ports. Connect the other end of the cable to the RJ-11 port of an analog telephone. Note that voice service must be provisioned by your service provider. 3.Connect an Ethernet cable (not supplied) to one of the yellow LAN (Ethernet) ports on the back panel of the modem and connect the other end to the Ethernet port of a PC. Use a Category 5e or Category 6 Ethernet cable. A PC should be connected initially for device installation and configuration. 4.Connect the power adapter (supplied) to the POWER port. Connect the other end to a power outlet. 5.Turn the modem on by pressing the ON/OFF button the rear panel. Analog Phone RJ-11 Optical Outlet RJ-45 2 Computer ON/OFF FIBER 5 1 3 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operation in the 5.15-5.25GHz band is restricted to indoor usage only. • Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. •FCC regulations restrict the operation of this device to indoor use only. •The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. •Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. UBN2310 Safety Manual • Federal Communication Commission (FCC) Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help.

10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2023-07-06 FCC ID: XCNUBN2310 Declaration for DFS master devices We, Ubee Interactive Holding Corp. Taiwan Branch. hereby declare that the device meets all the other requirements specified in Part 15E Section 15.407. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Lily Liu Director | Product Line Management Ubee Interactive Holding Corp. Taiwan Branch. Tel.: +886-3-560-0010*121 Fax.: +886-3-560-0017 E-mail: [email protected]

Date: 2023-07-07 FCC ID: XCNUBN2310 To the attention of Federal Communications Commission Authorization and Evaluation Division Attestation Statements Attestation Statements Part 2.911(d)(5)(i) Filing Ubee Interactive Holding Corp. Taiwan Branch certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Attestation Statements Part 2.911(d)(5)(ii) Filing Ubee Interactive Holding Corp. Taiwan Branch certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely yours, Lily Liu Director | Product Line Management Ubee Interactive Holding Corp. Taiwan Branch Tel.: +886-3-560-0010 Ext.107 Fax: +886-3-560-0017 E-mail: [email protected]

10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2023-07-07 FCC ID: XCNUBN2310 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Lily Liu Director | Product Line Management Ubee Interactive Holding Corp. Taiwan Branch. Tel.: +886-3-560-0010 Ext.107 10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan Tel: +886-3-560-0010 Fax: +886-3-560-0017 Fax: +886-3-560-0017 E-mail: [email protected]

10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2023-07-07 FCC ID: XCNUBN2310 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization) in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, Lily Liu Director | Product Line Management Ubee Interactive Holding Corp. Taiwan Branch. Tel.: +886-3-560-0010 Ext.107 Fax: +886-3-560-0017 E-mail: [email protected]

10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2023-07-07 FCC ID: XCNUBN2310 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Ubee Interactive Holding Corp. Taiwan Branch., hereby authorizes Emerald Chen / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Emerald Chen / Specialist of BV CPS Taoyuan on Ubee Interactive Holding Corp. Taiwan Branch.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, Lily Liu Director | Product Line Management Ubee Interactive Holding Corp. Taiwan Branch. Tel.: +886-3-560-0010 Ext.107 Fax: +886-3-560-0017 E-mail: [email protected]

Reference No.:BHQC-WTW-P23020342_EXT Page 1/6 CONSTRUCTION PHOTOS OF EUT Reference No.:BHQC-WTW-P23020342_EXT Page 2/6 Reference No.:BHQC-WTW-P23020342_EXT Page 3/6 Reference No.:BHQC-WTW-P23020342_EXT Page 4/6 Reference No.:BHQC-WTW-P23020342_EXT Page 5/6 AC Adapter 1 (Brand: MOSO ; Model: MS-V2000R120-024Q0-US) Reference No.:BHQC-WTW-P23020342_EXT Page 6/6

(Fig. 1) FCC ID: XCNUBN2310 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device.

Reference No.: BHQC-WTW-P23020342_INT Page 1/15 CONSTRUCTION PHOTOS OF EUT Reference No.: BHQC-WTW-P23020342_INT Page 2/15 Reference No.: BHQC-WTW-P23020342_INT Page 3/15 Reference No.: BHQC-WTW-P23020342_INT Page 4/15 Reference No.: BHQC-WTW-P23020342_INT Page 5/15 Reference No.: BHQC-WTW-P23020342_INT Page 6/15 Reference No.: BHQC-WTW-P23020342_INT Page 7/15 Reference No.: BHQC-WTW-P23020342_INT Page 8/15 Reference No.: BHQC-WTW-P23020342_INT Page 9/15 ANT1 Reference No.: BHQC-WTW-P23020342_INT Page 10/15 Reference No.: BHQC-WTW-P23020342_INT Page 11/15 ANT2 Reference No.: BHQC-WTW-P23020342_INT Page 12/15 ANT3 Reference No.: BHQC-WTW-P23020342_INT Page 13/15 Reference No.: BHQC-WTW-P23020342_INT Page 14/15 ANT4 Reference No.: BHQC-WTW-P23020342_INT Page 15/15

Report No.: MFBHQC-WTW-P22060972A Page No. 1 / 11 Report Format Version: 7.1.0 Reference No.: CHHW-WTW-P23020342 RF EXPOSURE REPORT CERTIFICATE OF CONFORMITY FCC Rule Part: FCC Part 2 (Section 2.1091) Report No.: MFBHQC-WTW-P22060972A FCC ID: XCNUBN2310 Product: GPON Brand: Model No.: UBN2310 Series Model: GR140IG Received Date: 2023/2/10 Test Date: 2023/6/6 Issued Date: 2023/7/3 Applicant: Ubee Interactive Holding Corp. Taiwan Branch Address: 10F-1, No.5, Taiyuan 1st ST, Zhubei City, Hsinchu County 302, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 Approved by: , Date: 2023/7/3 May Chen / Manager This test report consists of 11 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Prepared by : Vito Lung / Specialist This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBHQC-WTW-P22060972A Page No. 2 / 11 Report Format Version: 7.1.0 Reference No.: CHHW-WTW-P23020342 Table of Contents Release Control Record ....................................................................................................................................................... 3 1 Certificate .................................................................................................................................................................... 4 2 Measurement Uncertainty ......................................................................................................................................... 5 3 Test Instruments ........................................................................................................................................................ 5 4 Applicable RF Exposure Limit .................................................................................................................................. 6 5 Test Results ................................................................................................................................................................ 9 5.1 RF Exposure ............................................................................................................................................................. 9 6 Conclusion ................................................................................................................................................................ 10 7 Information of the Testing Laboratories ................................................................................................................ 11 Report No.: MFBHQC-WTW-P22060972A Page No. 3 / 11 Report Format Version: 7.1.0 Reference No.: CHHW-WTW-P23020342 Release Control Record Issue No. Description Date Issued MFBHQC-WTW-P22060972A Original release. 2023/7/3 Report No.: MFBHQC-WTW-P22060972A Page No. 4 / 11 Report Format Version: 7.1.0 Reference No.: CHHW-WTW-P23020342 1 Certificate Product: GPON Brand: Test Model: UBN2310 Series Model: GR140IG Sample Status: Mass product Applicant: Ubee Interactive Holding Corp. Taiwan Branch Test Date: 2023/6/6 FCC Rule Part: FCC Part 2 (Section 2.1091) Standard: KDB 447498 D04 Interim General RF Exposure Guidance v01 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Report No.: MFBHQC-WTW-P22060972A Page No. 5 / 11 Report Format Version: 7.1.0 Reference No.: CHHW-WTW-P23020342 2 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT. Measurement Specification Expanded Uncertainty (k=2) (±) RF Exposure 1 GHz ~ 2.5 GHz 1.2 dB 2.5 GHz ~ 8 GHz 1.3 dB 3 …

Text truncated - open the document above for the full version.

Confidential Version: TNP-21061_UBN2310BA00/U10G177.00 Released Date: 2023/04/27 Test Date: 2023/04/27 Tested By: Zhu-Wei Reviewed By: Daniel Confidential Contents ˋRevised History ˋSpecification ˋAntenna Placement & Condition ˋTest Setup for Return Loss, S-parameters Measurement ˋReturn Loss, S-parametersTest ˋIsolationTest ˋTest Setup for OTAMeasurement ˋ2D Radiation Patterns ˋ3D Radiation Patterns ˋResults Summary (Return Loss, S-parameters, Peak Gain, Efficiency) ˋConclusion & Comments 2 Confidential Revision History Released DateVersionRevisedRecords 2021/10/26V1.0•Antenna evaluation report 2021/11/18V1.1•ChangeAntenna Type 2021/12/06V1.2•ChangeAntenna Size 2021/12/18V1.3•Antenna evaluationwith new specification 2021/12/29V1.4•Change ANT2 placement &frequency (dual band) 2021/12/30V1.5•Antenna evaluation report 2022/01/04V1.6•Change antenna Cable length 2022/06/22V1.7•Change ANT2 Cable direction 2022/07/01V1.8•Change ANT2 Cable Routing (p.7) 2022/09/27V1.9•Change ANT2 cable length (L=80mm) 2023/02/13V2.0 •Update model name U10H175.00/U10G177.00 as customer request 2023/03/10V2.1•Updateanechoic chamberinformation (p.20) 2023/04/27V2.2•ChangeAntenna Cable routing(p.6~7) 3 Confidential Specification Requirements of Antenna Design Requirements of Measurement Test ItemSpecificationRemark ReturnLoss -10dBMax @2400-2500 / 5050-5825 MHz Isolation <-25dB Peak Gain 2.4GHz (Dual Band) <3.5 dBi 5GHz (DualBand) <4.0 dBi 5GHz <3.5 dBi Efficiency 2.4GHz ≥70% @2400-2500 MHz 5GHz ≥70% @5050-5825 MHz Radiation Pattern Scale: +5 --45 dBi, Angle step size: 5 degree RF FunctionNumber of ANTFrequency BandRemark Wi-Fi(2.4/5G)22400-2500 / 5050-5825 MHzANT1, 2 Wi-Fi(5G)25050-5825 MHzANT3, 4 4 Confidential Cable Loss AntennaCable Length (mm) Cable Loss(unit: dB) 2.4GHz5GHz ANT1230 mm0.79351.1270 ANT280 mm0.27230.3868 ANT3135 mm/0.6615 ANT4105mm/0.5145 CV2X_1 5 1M Cable Loss (unit: dB) 1GHz2GHz2.45GHz3GHz4GHz5GHz5.2GHz5.8GHz6GHz 1.13mm≤2.2≤3.1≤3.45≤3.8≤4.4≤4.9≤5.0≤5.3≤5.4 Confidential Antenna Placement & Solution CV2X_1 8 AntennaPrevious VersionCurrent Version ANT1 ANT2 ANT3 ANT4 Confidential TestSetupfor Return Loss Test 9 Antenna RF Cable with I-PEX conn. Network Analyzer EquipmentBrandModelS/N Network AnalyzerKeysightE5071CMY46417759 Calibration date：2022/12/28 Confidential Test StepsforReturn Loss 10 Step 6 Record the Results •Once the test is completed, record the measurement results. These results are usually presented in the form of graphs or tables for further analysis and comparison. Step 1 Configure the Network Analyzer •Turn on the network analyzer •Perform initialization •Setting the appropriate frequency range and measurement parameters. Step 2 Calibrate the Network •Before starting the test, calibrate to eliminate the inherent response of the test system. •Perform full open, full short, and full load calibration, as well as calibration of the reference plane. Step 3 Set the Test Parameters •Set the desired test parameters on the network analyzer. This typically includes selecting the desired S-parameter type (e.g., S11, S21, etc.), frequency range, and power level. Step 4 Connect the Antenna •Properly connect the antenna to the test port of the network analyzer. •Ensure a secure connection and use suitable adapters and cables to minimize signal loss. Step 5 Perform the Test •Begin the S-parameter test of the antenna. This will measure the reflection and transmission characteristics of the antenna within the selected frequency range. Confidential ANT1 (2400-2500 / 5050-5825 MHz) (Criterion: <-10 dB) Return LossTest 11 Confidential ANT2 (2400-2500 / 5050-5825 MHz) (Criterion: <-10 dB) Return LossTest 12 Confidential ANT3 (5050-5825 MHz) (Criterion: <-10 dB) Return LossTest 13 Confidential ANT4 (5050-5825 MHz) (Criterion: <-10 dB) Return LossTest 14 Confidential ANT1&ANT2 (Criterion: <-25dB) 15 Isolation Test Confidential ANT1&ANT3 (Criterion: <-25dB) 16 Isolation Test Confidential ANT1&ANT4 (Criterion: <-25dB) 17 Isolation Test Confidential ANT2&ANT3 (Criterion: <-25dB) 18 Isolation Test Confidential ANT2&ANT4 (Criterion: <-25dB) 19 Isolation Test Confidential ANT3&ANT4 (Criterion: <-25dB) 20 Isolation Test Confidential ChamberBrandModelSerial No.DateDimensionFreq. RangeFunctionLocation Single-probeWaveProFFC-700WP-C07-0032007/10/243.25*3.25*7M0.4 ~ 6 GHz •Gain and Efficiency •3D Radiation pattern •TRP & TIS: 2G/3G/4G LTE/802.11 a/b/g/n/NB- IOT/BT China, Dongguan Chamber Information 21 Test software:AnTestpro99 Calibration date:2023/02/13 •Hardware items and control wiring marked in blue are components provided by the additional accessory kit. •RF components and RF interconnection lines marked in red (excluding the dashed parts) are additional accessories provided by the RF accessory kit. Confidential ANT1 Front ViewBack View 3D Radiation Pattern 27 5050MHz 2450MHz Confidential ANT1 Front ViewBack View 3D Radiation Pattern 28 5825MHz 5350MHz Confidential ANT2 Front ViewBack View 3D Radiation Pattern 29 5050MHz 2450MHz Confidential ANT2 Front ViewBack View 3D Radiation Pattern 30 5825MHz 5350MHz Confidential ANT3 Front ViewBack View 3D Radiation Pattern 31 5150MHz 5050MHz Confidential ANT3 Front ViewBack View 3D Radiation Pattern 32 5825MHz 5350MHz Confidential ANT4 Front ViewBack View 3D Radiation Pattern 33 5150MHz 5050MHz Confidential ANT4 Front ViewBack View 3D Radiation Pattern 34 5825MHz 5350MHz Confidential Return Loss (2400-2500 / 5050-5825 MHz) (Criterion: <-10dB) Frequency (MHz) ANT1ANT2ANT3ANT4 2400 -16-16// 2450 -22-31// 2500 -17-17// 5050 -19-27-20-21 5150 -17-26-25-21 5350 -26-25-24-31 5550 -19-15-17-20 5725 -19-13-19-16 5825 -21-12-22-15 Results Summary 35 Confidential Isolation(Criterion: <-25dB) Frequency (MHz) ANT1 & ANT2 ANT1 & ANT3 ANT1 & ANT4 ANT2 & ANT3 ANT2 & ANT4 ANT3 & ANT4 2400 -28-34-49-32-30-32 2450 -28-32-50-30-31-32 2500 -29-31-59-31-34-34 5050 -32-33-39-41-34-37 5150 -34-34-37-38-34-36 5350 -35-33-41-34-31-44 5550 -33-33-41-38-36-50 5725 -35-31-47-37-35-50 5825 -38-33…

Text truncated - open the document above for the full version.

Report No.: RFBHQC-WTW-P22060972A-2 Page No. 1 / 29 Report Format Version: 6.1.2 Reference No.: CHHW-WTW-P23020342 Supplemental “Transmit Simultaneously” Test Report Report No.: RFBHQC-WTW-P22060972A-2 FCC ID: XCNUBN2310 Test Model: UBN2310 Received Date: 2023/2/10 Test Date: 2023/5/25 ~ 2023/6/8 Issued Date: 2023/7/3 Applicant: Ubee Interactive Holding Corp. Taiwan Branch Address: 10F-1, No.5, Taiyuan 1st ST, Zhubei City, Hsinchu County 302, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwa. Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan FCC Registration / Designation Number: 723255 / TW2022 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBHQC-WTW-P22060972A-2 Page No. 2 / 29 Report Format Version: 6.1.2 Reference No.: CHHW-WTW-P23020342 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.1.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.2 Description of Support Units .............................................................................................................. 11 3.2.1 Configuration of System under Test .................................................................................................. 12 4 Test Types and Results ...................................................................................................................... 13 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 13 4.1.2 Test Instruments ................................................................................................................................ 14 4.1.3 Test Procedures ................................................................................................................................. 16 4.1.4 Deviation from Test Standard ............................................................................................................ 16 4.1.5 Test Setup .......................................................................................................................................... 17 4.1.6 EUT Operating Conditions ................................................................................................................. 18 4.1.7 Test Results ....................................................................................................................................... 19 4.2 Conducted Emission Measurement .................................................................................................. 22 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 22 4.2.2 Test Instruments ................................................................................................................................ 22 4.2.3 Test Procedures ................................................................................................................................. 23 4.2.4 Deviation from Test Standard .............................................................…

Text truncated - open the document above for the full version.

Report No.: RFBHQC-WTW-P22060972A-3 Page No. 1 / 402 Report Format Version: 6.1.2 Reference No.: CHHW-WTW-P23020342 …

Text truncated - open the document above for the full version.