XCNDDW36CWireless Cable Modem

Ubee Interactive — www.ubeeinteractive.com 1 Ubee DDW36C – Safety and Installation Product Insert v1.0 DDW36C Advanced Wireless Gateway - Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Regulatory Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Ubee Interactive — www.ubeeinteractive.com 2 Ubee DDW36C – Safety and Installation Product Insert v1.0 Operation within 5.15 ~ 5.25 GHz frequency range is restricted to indoor environment. FCC Radiation Exposure Statement: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated at a minimum distance of 38cm between itself and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Safety Notices Read these instructions carefully before operating the device. It is important to be aware of these safety instructions. Install the device according to these instructions and keep this guide for future reference. 1. Do not use this device in a humid space, in the rain, or near splashing water. 2. Do not install during thunder or lightning storms. 3. Do not cover any ventilation openings in the device case. 4. Do not place the device near heat sources such as radiators or stoves. 5. Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. 6. Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with Ubee Interactive — www.ubeeinteractive.com 3 Ubee DDW36C – Safety and Installation Product Insert v1.0 phase-to-phase voltage at 100-120V. 8. Disconnecting the Device : If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. 9. The device should be installed in a location not to exceed the maximum temperature of 40 degrees Celsius (104 degrees Fahrenheit). 10. When this device is placed upright with the aid of the stand, the st and must be fixed at a 90-degree angle to the device. Otherwise, the device will have the risk of tipping over. 11. Keep the device away from Children and Pets. 12. Place the device on a cool surface. Failure to do so may result in overheating which can cause extreme damage. 13. Do not modify or attempt to disassemble the device. Use it only according to the instructions. 14. Do not dispose of the device in a trash container. Please recycle. Installation To install this device, follow the procedures below and refer to the following page for a connection diagram. 1. Connect one end of a coaxial cable (not included) to the CABLE port on the device. Ubee Interactive — www.ubeeinteractive.com 4 Ubee DDW36C – Safety and Installation Product Insert v1.0 Connect the other end to a cable splitter or the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. If you plan to connect the device and a television to the same cable wall outlet, you must use a cable line splitter (not included). 2. Connect one end of the supplied Ethernet cable to one of the ETHERNET ports (ETH1 to ETH4) on the device. Connect the other end to the ETHERNET port on a PC. Note: Category 5e or Category 6 Ethernet cables with RJ-45 connectors must be used when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds (unless the computer does not support it). 3. Connect the power cord to the POWER port on the device. Plug the other end of the power cord into the AC wall outlet. Important: Use only the power cord that is shipped with the device. Additional Information 1. RESET Button (back of device): This button resets the device to fa ctory default s. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note : Not all Ubee Interactive — www.ubeeinteractive.com 5 Ubee DDW36C – Safety and Installation Product Insert v1.0 parameters are reset to factory defaults. Refer to the User Guide for more information. 2. WPS button (top of device): The WPS button is used for the Wi-Fi Protected Setup (WPS) method to connect a Wi…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

1 5pallet label503.00089.0052/120 4carton label503.00092.0051/10 3PTT label 500.01738.005 1 2.2giftbox label503.01076.0051 2.1housing label503.01076.0051 1HH label503.00096.0151 ItemDescriptionFoxconn PNQTY 2.1 3 2.2 4 5 U10C093.10 XXXXXXX U10C093.10 LF MO-VVSS 20mm 12mm TITLE: HonHai label P/N:503.00096.015 LABEL TEXT: 1.barcode content Foxconn barcode: 7digit (code 128) XXXXXXX barcode content words(ditto description) 2.blank for customer 3.Part number: U10C093.10 4.MO-VVSS Notes: 1. VV:the engineering version(refer to Foxconn label Rev column in the cover of the MFG document) 2. SS:the version of A300/A400 product(refer to Doc Rev. in the cover of MFG document) LOCATIONLOCATIONNAME 0 1 2 3 4 5 6 7 8 9 A B C DDummy Lable E F D10 G E5 HTMM J E6 K L MEASTAR N CBT P RMA Q R RMA S CPE2 T (S) V (N) Y (CPEI) Z U (CPEII) (CMB) 0.0 Height:3mm Height:3mm Font:5pt Font:7.5pt Font:7pt Font:5pt 2014.03.25 2014.06.30 2014.07.01 1 2 U10C093.10503.01076.005 50# Mylar Housing Label+Box Label Sunny NOTES: 1.All of the barcode range please refer to the test spec. Barcode format: code 128 Font: Arial Housing Label 503.01076.005-1 stick on housing Box Label 503.01076.005-2 stick on box Cun CatherineUpdate label barcode size and font size Update password rule Catherine Ubee P/N: DDW36C1 S/N= 1234567YYYYYY Cable RF MAC Address = XXXXXXXXXXXX WAN-MAN MAC Address = XXXXXXXXXXXX DC: MMDDYY ASSEMBLED IN XXXXX S/N= 1234567YYYYYY Cable RF MAC Address = XXXXXXXXXXXX WAN-MAN MAC Address = XXXXXXXXXXXX SSID: WIFIXXXXXX-2.4G WPA2-PSK: XXXXXXXXXXXXXXXX SSID: WIFIXXXXXX-5G GUI access URL: http://192.168.100.1 DC: MMDDYY ASSEMBLED IN XXXXX H/W Version: X.X.X WPS PIN: XXXXXXXX GUI password: XXXXXXXXXXXX GUI username: admin Catherine 40 5.GUI username admin 6.GUI password: XXXXXXXXXXXX XXXXXXXXXXXX:12 characters,must be a randomlygenerated character string,created individually for each unit at time of manufacture.(It MUST be restricted to some combination of uppercase alphabetical letters, lowercase alphabetical letters, number characters, and printable special characters.) Special characters must be limited to: !, #, $, &, %, * The following characters are not allowed: upper case O (OH), 0 (zero), lower case l (el), upper case I (EYE) upper case Z,upper case S, upper case B. 7.WPA2-PSK: XXXXXXXXXXXXXXXX 16 characters,must be a randomlygenerated character string,created individually for each unit at time of manufacture (It must use only uppercase alpha-numeric characters,excluding the number "0" and "O", with no punctuation) 8.WPS PIN: XXXXXXXX The format of the PIN must be a randomly generated eight(8) digit number in accordance with the WPS specification. 4.GUI access URL: http://192.168.100.1 10.DC (Date Code), in MMDDYY format: MM表示月， DD表示天，YY表示年 11.ASSEMBLED IN XXXXX (XXXXX:Country of Manufacture, base on the manufacture factory) 2.SSID: WIFIXXXXXX-2.4G XXXXXX: the last 3 octets(6 digits) of the RF MAC address using only uppercase alpha-numeric characters with no punctuation. 3.SSID: WIFIXXXXXX-5G XXXXXX: the last 3 octets(6 digits) of the RF MAC address using only uppercase alpha-numeric characters with no punctuation. 9.H/W Version: X.X.X Please refer to test spec.,it's same as "H/W version check" 2 2 1 0.02014.03.19 U10C093.10 PTT Label 500.01738.005 Sunny 1/1 "X": UL Factory ID, Foxconn printing Arial 6pt NOTES: 1.Material: #50 Mylar + 25# PET(matte, printable) 2.Adhesive: 3.Adhesive thickness : 50#Mylar: 0.030+/-0.003mm 25#PET: 0.018+/-0.003mm 4.Printing Color:Black 5.Background: White 6.Liner:Glassine release paper 7.Packaging Style: Reel 8.The part must be RoHS compliant Package style Vendor provide Foxconn printing Arial Bold,8.4pt I.T.E. E199598 8G92 Vendor code Foxconn printing Arial Regular,8.4pt Cun Model: Ubee Part No.: Rating: 120VAC/60Hz/0.9A Model name: DDW36C FCC ID: XCNDDW36C This device complies with part 15 of the FCC Rules. I.T.E. E199598 8G92 Factory ID: X Model: DDW36C Ubee Part No.: DDW36C1 Rating: 120VAC/60Hz/0.9A Model name: DDW36C FCC ID: XCNDDW36C This device complies with part 15 of the FCC Rules. I.T.E. E199598 8G92 Factory ID list =========================== (100544-836) FUHONG PRECISION COMPONENT (BAC GIANG) LTD DINH TRAM INDUSTRY PARK VIET YEN DISTRICT VIET NAM Factory ID: Y =========================== (100568-850) NANNING FUGUI PRECISION INDUSTRIAL CO LTD 18 ZONGBU RD NEW & HIGH-TECH INDUSTRIAL DEVELOPMENT ZONE NANNING GUANGXI CHINA Factory ID: N ============================ (128685-001) AMBIT MICROSYSTEMS (SHANGHAI) LTD 1925 NAN-LE RD SONGJIANG EXPORT PROCESSING ZONE SHANGHAI 201613 CHINA Factory ID: E ================================ (223850-001) HONG FU JIN PRECISION INDUSTRY (SHENZHEN) CO LTD 10TH YOUSONG INDUSTRIAL DISTRICT 2ND DONGHUAN RD NO 2 BAO'AN LONGHUA TOWN SHENZHEN 518109 GUANGDONG CHINA Factory ID: F ================================== Catherine 0.1 2014.04.23 update rating Cun 0.2 2014.06.17 update FCC ID and Model name Catherine 2014.03.20 DVW2100 Yanli Yu 503.00092.005U10C093.10 4/5 Carton Label Notes: 1.Background color: White 2.Printing color: Black 3.Meterial: art paper 4.Size: 101.6mm*165.1mm 5.Carton ID: follow Foxconn rule 6.DATE/TIME(Variable) that modem was assembled According to the actual manufacturing time to print DATE: MM/DD/YY (e.g.: DATE: 04/23/12) TIME: HH:MM (e.g.: TIME: 14:52) 7.Assembled in XXXXXX: Country of Manufacture (base on the manufacture factory) 8.MAC and SN range please refer to the test spec. 9.Stick position please refer to ASY document Font: Arial Barcode: code 128 Carton ID: CXXXXXXXXXX 1234567YYYYYYXXXXXXXXXXXXXXXXXXXXXXXX THIS PRODUCT CONTAINS ENCRYPTION AND MAY REQUIRE U.S. AND/OR LOCAL GOVERNMENT AUTHORIZATION PRIOR TO EXPORT OR IMPORT TO ANOTHER COUNTRY Ubee P/N: DDW36C1 Foxconn P/N: U10C093.10 Qty: 10 Product: Assembled in XXXXXX DATE: MM/DD/YY TIME: HH:MM Serial NumberCable RF MACWAN-MAN MAC 1234567YYYYYYXXXXXXXXXXXXXXXXXXXXXXXX 1234567YYYYYYXXXXXXXXXXXXXXXXXXXXXXXX 1234567YYYYYYXXXXXXXXXXXXXXXXXXXXXXXX 1234567YYYYYYXXXXXXXXXXXX…

Text truncated - open the document above for the full version.

Label Location

Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10

Page 1 of 16 Antenna Design For 鴻海U10C093 V1.06 Document Number NE3-14017 1 st Released Date 02/07/2014 Last Released Date 07/08/2013 Author David Feng Review by Sky Page 2 of 16 Revised History Date Version Revised Record 02/11/14 1.00 z 1 st released 03/06/14 1.01 天線設計於客戶Mock-up機台中. 03/12/14 1.02 Ant3變更設計,線徑為1.37mm. 03/21/14 1.03 Ant2 and Ant3變更設計,線徑為1.37mm. 05/05/14 1.04 Ant2 and Ant3變更線材固定方式. 06/27/14 1.05 變更天線設計與線材出線方式. 07/08/14 1.06 變更天線設計. Page 3 of 16 Electrical Specification Rough description Dual Band PCB antenna for U10C093 Item Initial Specification Final Specification Dimensions Ant1. (L)44*(W)35*(H)0.8mm Ant2. (L) 41.65*(W)12.25*(H)0.8mm Ant3. (L)50*(W)35*(H)0.8mm Impedance 50Ω Test environment With Housing Spectrum 802.11 abcgn Freq. Range 2.4~2.5GHz / 4.9~5.825GHz Antenna type PCB ANT Gain 6.0Max. @ 2GHz 5.0 Max. @ 5GHz VSWR 1.92：1 Radiation Omni Polarization Linear HPBW / H None HPBW / E None Rad. efficiency 60% Connector type I-PEX Cable type Ф1.37mm Cable length None Isolation -20 dB (MAX.) Page 4 of 16 1. Antennas setup and environment Ant1. Dimension: (L)44mm*(W)35mm*(H)0.8mm Ф1.37mm Cable Length: 142mm (Black) Ant1. Ant3. Ant2. Dimension: (L) 41.65*(W)12.25*(H)0.8mm Ф1.37mm Cable Length: 243mm (Gray) Ant2. Page 5 of 16 2. Network Analyzer Measurement Test Environment Ant3. Dimension: (L)50mm*(W)35mm*(H)0.8mm Ф1.37mm Cable Length: 288mm (White) Page 6 of 16 2.1 S-parameter Test Results 2.1.1 Ant1. 2.1.2 Ant2. Page 7 of 16 2.1.3 Ant3. 2.2 Isolation 2.2.1 Ant1. & Ant2. Page 8 of 16 2.2.2 Ant1. & Ant3. 2.2.3 Ant2. & Ant3. Page 9 of 16 3. Gain & Patterns test results 3.1 Lab information z Lab name：Satimo z Address ：No.326 Sec.2, Kung Tao 5 Road, HsinChu City, Taiwan z Certification：none (Satimo system certification: CTIA, 3GPP, Wi-Fi alliance and WiMAX Forum) z Size (LxWxH)：5m x 5m x 5m z Isolation level：>100dB z Normal applications：antenna radiation pattern measurement, OTA performance testing. z Frequency measurement range：0.4 to 6 GHz z EUT scanning method：conical cut method z Measurement distance：1.6m z Measurement antenna specification (for θ and Φ polarization each)：dual polarization antenna for 0.4 to 6.0 GHz frequency range z Equipment list： Page 10 of 16 3.2 Measurement setting XY YZ XZ 0° Right Up Up 90° Back Back Right 180° Left Down Down 270° Front Front Left Down Up(+Z) Left Front Back(+Y) Right (+X) AUT X Y Z Page 11 of 16 θ φ To t a l a n g l e 175 ̊ 360 ̊ How many angle scan one point 5 ̊ 5 ̊ Total scan point 36 73 Page 12 of 16 3.3 2D patterns 3.3.1 Ant1. X-Z Plane (E-total) Y-Z Plane (E-total) X-Y Plane (E-total) Page 13 of 16 3.3.2 Ant2. X-Z Plane (E-total) Y-Z Plane (E-total) X-Y Plane (E-total) Page 14 of 16 3.3.3 Ant3. X-Z Plane (E-total) Y-Z Plane (E-total) X-Y Plane (E-total) Page 15 of 16 4. Summary 4.1 Return Loss Frequency Ant 1 (dB) Ant 2 (dB) Ant 3 (dB) 2400MHz -24.2 -18.2 -19.3 2450MHz -19.5 -12.3 -15.2 2500MHz -14.1 -10.1 -14.0 4900MHz -11.3 -18.4 -10.5 5150MHz -11.5 -19.6 -12.1 5350MHz -15.0 -16.4 -17.6 5725MHz -11.5 -16.9 -12.8 5825MHz -13.9 -21.2 -15.8 4.2 Isolation Frequency Isolation Ant 1&Ant2 (dB) Isolation Ant 1&Ant3 (dB) Isolation Ant 2&Ant3 (dB) 2400MHz -22.6 -27.2 -24.3 2450MHz -24.2 -23.8 -23.8 2500MHz -27.9 -23.5 -23.8 4900MHz -29.8 -31.4 -33.3 5150MHz -31.2 -28.2 -35.9 5350MHz -32.6 -28.0 -33.2 5725MHz -29.1 -30.0 -30.2 5825MHz -28.6 -29.2 -31.3 Page 16 of 16 4.3 3D total Peak Gain & Efficiency Frequency Ant 1 Ant2 Ant3 Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) Peak Gain (dBi) Efficiency (%) 2400MHz 4.5 70.6 5.5 73.7 3.2 70.7 2450MHz 4.8 67.1 6.0 73.9 3.2 67.6 2500MHz 5.6 63.4 5.3 69.1 4.0 61.9 4900MHz 4.2 65.9 4.1 62.6 2.8 60.7 5150MHz 4.6 68.7 4.8 69.2 4.4 64.2 5350MHz 4.3 73.5 4.3 64.6 4.4 64.1 5725MHz 4.4 65.5 4.5 62.0 4.0 60.4 5825MHz 5.0 69.2 4.8 66.2 4.3 65.3

Report No.: SA140414C09 1 of 7 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140414C09 MODEL NO.: DDW36C FCC ID: XCNDDW36C RECEIVED: Apr. 14, 2014 ISSUED: Aug. 01, 2014 APPLICANT: Ubee Interactive Corp. ADDRESS: 10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA140414C09 2 of 7 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE ............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................. 6 Report No.: SA140414C09 3 of 7 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140414C09 Original release. Aug. 01, 2014 Report No.: SA140414C09 4 of 7 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Wireless Cable Modem MODEL: DDW36C BRAND: Ubee Interactive APPLICANT: Ubee Interactive Corp. TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: DDW36C) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Aug. 01, 2014 Pettie Chen / Senior Specialist APPROVED BY : , DATE : Aug. 01, 2014 Ken Liu / Senior Manager Report No.: SA140414C09 5 of 7 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 38cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA140414C09 6 of 7 Report Format Version 5.0.0 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For Non-Beamforming Mode: FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 29.72 10.01 38 0.518 1 5180-5240 25.02 9.37 38 0.151 1 5745-5825 29.64 9.48 38 0.450 1 NOTE: 2.4GHz Band: Directional gain = 10 log[(10 G1/20 + 10 G2/20 + ... + 10 GN/20 ) 2 ] =10.01dBi 5180-5240MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 ]= 9.37dBi 5745-5825MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 ]= 9.48dBi CONCULSION: Both of the 2.4 and 5GHz can transmit simultaneously, the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density 1. WLAN 2.4G + WLAN 5.0G = 0.518 + 0.450 = 0.968 Therefore, the maximum calculation of this situation is 0.968, which is less than the “1” limit. Report No.: SA140414C09 7 of 7 Report Format Version 5.0.0 For Beamforming Mode: FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 27.74 10.01 38 0.328 1 5180-5240 25.62 9.37 38 0.174 1 5745-5825 26.51 9.48 38 0.219 1 NOTE: 2.4GHz Band: Di…

Text truncated - open the document above for the full version.

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: Rev. 01 FCC RADIO TEST REPORT Applicant’s company Ubee Interactive Applicant Address 10F-1, No. 5, Taiyuan 1st St. Jhubei City, Hsinchu County 302, Taiwan, R.O.C. FCC ID XCNDDW36C Product Name Wireless Cable Modem Brand Name Ubee Interactive Model No. DDW36C Test Rule Part(s) 47 CFR FCC Part 15 Subpart E § 15.407 Test Freq. Range 5150 ~ 5250MHz Received Date Jun. 18, 2014 Final Test Date Jul. 27, 2014 Submission Type Original Equipment Statement Test result included is for the IEEE 802.11n and IEEE 802.11a/ac of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2009, 47 CFR FCC Part 15 Subpart E, KDB789033 D02 v01, KDB 662911 D01 v02r01, KDB644545 D01v01r02. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR470106AB Report Format Version: Rev. 01 Page No. : ii of ii FCC ID: XCNDDW36C Issued Date : Aug. 07, 2014 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................5 3.3. Table for Filed Antenna.......................................................................................................................................................................6 3.4. Table for Carrier Frequencies .............................................................................................................................................................7 3.5. Table for Test Modes ...........................................................................................................................................................................8 3.6. Table for Testing Locations..................................................................................................................................................................9 3.7. Table for Supporting Units ...................................................................................................................................................................9 3.8. Table for Parameters of Test Software Setting ...................................................................................................................................10 3.9. EUT Operation during Test .................................................................................................................................................................11 3.10. Duty Cycle ........................................................................................................................................................................................12 3.11. Test Configurations ...........................................................................................................................................................................13 4. TEST RESULT ................................................................................................................................................... 17 4.1. AC Power Line Conducted Emissions Measurement.........................................................................................................................17 4.2. 26dB Bandwidth and 99% Occupied Bandwidth Measurement......................................................................................................21 4.3. Maximum Conducted Output Power Measurement .........................................................................................................................33 4.4. Power Spectral Density Measurement ..............................................................................................................................................37 4.5. Radiated Emissions Measurement ....................................................................................................................................................46 4.6. Band Edge Emissions Measurement .................................................................................................................................................68 4.7. Frequency Stability Measurement ....................................................................................................................................................77 4.8. Antenna Requirements .....................................................................................................................................................................79 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 80 6. MEASUREMENT UNCERTAINTY.......................................................................................................................... 82 APPENDIX A. TEST PHOT…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST