XO9-DSCF-003A cat flap with an integrated short range RFID reader

DSCF ENGLISH Safety Guide tool version V 1.7 IMPORTANT SAFETY INFORMATION It is your responsibility to exercise discretion and observe all safety measures required by law and common sense. Please read the following information carefully and retain this manual for future reference. This product is intended for use by domestic pets only. WARNING: ● Your DSCF is not a toy. Do not allow children to play with the Product. ● Your DSCF includes some small components. To avoid the risk of choking take care to keep any loose parts away from young children or pets and dispose of all packaging appropriately. This product can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be undertaken by children without supervision. CHILD PROOFING: In households with young children, you must include the DSCF in childproofing considerations. Misuse of this product by a child may result in persons coming into contact with potential dangers. Young children should be monitored at all times when in the immediate vicinity of the DSCF. BATTERIES: The DSCF requires 4 good quality 1.5 V LR6 alkaline “AA” cells to operate. The product is not designed for use with Rechargeable batteries. ● Always change all 4 batteries at the same time and avoid mixing battery types or manufacturers. ● To insert or change the batteries, remove the battery cover from the front of the product to access the battery compartment. ● Ensure the +/- symbols on the new batteries match the symbols on the DSCF ● Non-rechargeable batteries are not to be recharged. ● To avoid the risk of fire always take care to ensure batteries are fitted the correct way round as marked on the DSCF and never short circuit the battery terminals. ● If the batteries are exhausted, or there is a problem with how they have been inserted, the light adjacent to the battery compartment will flash red every 5 seconds as a Low battery indication. ● There is a risk of explosion if the battery is replaced by an incorrect type. Always use good quality batteries from a reputable battery manufacturer to ensure the best performance. Exhausted or out-of-date batteries must be removed and disposed of properly in accordance with local legislation. If the appliance is to be stored unused for a long period, the batteries must be removed. In case of battery leaks, wear appropriate Personal Protective Equipment (PPE) to protect yourself from any exposure to harmful chemicals before disposing of the batteries and cleaning any spillage. When cleaning up a spillage, avoid contact with skin, eyes or any risk of ingestion. Contact a medical professional immediately if this should occur. Do not use this product if parts are missing, damaged or worn. Only use approved Sure Petcare accessories and spare parts with you DSCF. PETS: To ensure your pet's safety ● Clean unit with Pet friendly cleaning products and a damp cloth only, do not immerse in water. Sure Petcare recommends the DSCF is used with your pet’s implanted microchip, however it may also be operated using the Sure Petcare RFID Collar Tag. If using a collar tag, it must be used with a safety collar which incorporates a breakaway buckle. Sure Petcare cannot accept liability for any injury or death caused by a pet's collar. Custom software settings are available from customer support to alleviate most unwanted pet behaviour Before Installation or using the product please download and read the user instructions, these are available from www.surepetcare.com/pdf. Disposal of old Products and used Batteries: Either of these symbols on a product indicates it is subject to the following legislation: Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE) & Directive 2006/66/EC on Batteries and Accumulators require households to dispose of electrical products and waste batteries in an environmentally responsible manner. These items should not be placed in household waste bins and must be recycled at an appropriate recycling facility. Further information on recycling can be found at: www.recycle-more.co.uk . FCC compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device has been designed and complies with the safety requirements for RF exposure in accordance with FCC rule part §2.1093 and KDB 447498 D01 IC compliance: CAN ICES-3(B)/NMB-3(B): This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To meet RF exposure guidelines, a separation distance of 200 mm should be maintained. This device complies with the safety requirements for RF exposure in accordance with RSS-102 Issue 5 for portable use conditions. Conformité IC: CAN ICES-3(B)/NMB-3(B): Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Pour respecter les consignes d’exposition aux RF, une distance de séparation de 200 mm doit être maintenue. Cet appare…

Text truncated - open the document above for the full version.

SureFlap Ltd Ground Floor Building 2030 , Cambourne Business park, Cambourne, CB23 8DW, United Kingdom Authorisation Letter To whom it may concern This is to certify that SureFlap Ltd. herby authorises TUV SUD to act as the TCB for the application of the Dual Scan Cat Flap v2, FCC ID XO9-DSCF1003 to the FCC We certify that SureFlap Ltd is not subject to a denial of Federal benefits, that include the FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C. § 862 because of a conviction for the possession or distribution of a controlled substance. See 47 CFR1.2002(b) for the definition of part for these purposes. Yours faithfully, Dr. David Hallas, Managing Director

SureFlap Ltd. Trading as Sure Petcare • Company No. 06399085 SureFlap Ltd 7 the Irwin Centre Scotland Road Dry Drayton CB23 8AR, Cambridgeshire DSCF v2 and iDSCF Similarity Justification To whom it may concern The Sure Petcare DSCF v2 is produced as a downgraded version of the pre existing iDSCF design. The product is functionally identical to the existing iDSCF save for the deletion of the 802.15.4 2.4 GHz transceiver function removing all networking capability. The DSCF v2 is mechanically identical to the iDSCF and uses identical bare PCBs but with the components for the 2.4 GHz transceiver and for decoding TROVAN Microchips deleted. The RFID performance of the unit is not affected by these changes. Yours faithfully, Dr. David Hallas, Managing Director

Federal Communications Commission Authorization and Evaluation Division 21 st April 2021 Subject: Confidentiality Request re application for certification of FCC ID: XO9-DSCF-1003 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name(s) Block Diagram DSCF v2 BlockDiagram Part List 01761-EB_01 DSCF2 Microchip DualScan Catflap Main PCB eBOM 01321-EB_01 iDSCF Tunnel Sensor - Receiver – eBOM 01318-EB_01 iDSCF Tunnel Sensor - Emitter – eBOM 00834-EB_03 iDSCF Front Sensor - Receiver – eBOM 00831-EB_03 iDSCF Front Sensor - Emitter – eBOM DSCF001_WT_03 DualScan Microchip Catflap Top Level BOM 10908-DA_01 DualScan 2 General Assembly iDSCF mechanical BoM Schematic and PCB data DSCF2 schematic iDSCF - PCB Layout The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Yours faithfully, David Hallas Managing Director

DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 1 of 6 Product Images Front view Note the logo shown in the blue circle will not be present on production parts. DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 2 of 6 Lefthand side view DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 3 of 6 Righthand side view DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 4 of 6 Rear view DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 5 of 6 Top View DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCFS003 Model ID: DSCF Page 6 of 6 Underside view

163.0 20.0 6.0 (4x) PRODUCT CODE PATENT INFORMATION AND URL FCC NUMBER IC NUMBER R-NZ MARKING SURE PETCARE URL RCM MARKING CE MARKING WEEE MARKING UKCA MARKING EFUP 10 MARKING Rev01 - Initial Release NOTES: FONT: ARIAL TO BE APPLIED TO: REAR COVER - 00437-DC REVISIONS Rev.ECN No.DateChanged by 01-24/08/2020A.Bliss COMPLIANCE INFORMATION UL Flammability RatingN/A Conformity MarkingsEFUP 10, R-NZ, RCM, CE, WEEE, UKCA Material Data Sheet 1T:\Engineering\Mechanical & Product Design\Datasheets\Labels\Polyester\1510134400-4192.pdfNot Available Template: Sure Petcare A4 landscape SolidWorks Drawing Sure Petcare 7 The Irwin Centre Scotland Road, Dry Drayton Cambridge, CB23 8AR, UK Tel: +44(0)1954 211664 [email protected] www.surepetcare.com Print Black Silver Matt on Print Side, Adhesive on Non Print Side Material Manufacturer: Up to 6: 30: 120: 315: 1000: 2000: Angular: © Copyright 2018 Sureflap Ltd. trading as Sure Petcare CONFIDENTIAL DO NOT SCALE Sheet: Tolerances unless otherwise specified: Material Grade: Over 0 6 30 120 315 1000 Grade II ±0.1 ±0.2 ±0.3 ±0.5 ±0.8 ±1.2 ±1º 10874-DC 10874-DC DualScan 2 N/A 1 of 1 1:1 mm A4 Dual Scan Compliance Label Model Filename:Changes: Third Angle Projection Product:Format: Units: Scale: Colour:Supersedes: Drawn by:Finish/ Coating: Material Type: Description: Part Number: A.Bliss 0.72 g 716.69 mm³ Volume: Weight: 01 Revision: D C BB AA 1 1 2 2 3 3 4 4 5 5 6 6 50μ Top Coated Polyester Film Silver Matt Sticker 3M G62SB Customark

SureFlap Ltd Ground Floor Building 2030 , Cambourne Business park, Cambourne, CB23 8DW, United Kingdom Compliance label location Detail information taken from “Rear Assembly” drawing number 10913-DA_01

DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 1 of 7 Product Internal Images Product with front cover removed – oblique view DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 2 of 7 Product with front cover removed – top down view – note motor location at bottom of unit DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 3 of 7 Inside of the front cover showing latch system DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 4 of 7 View from above showing battery tray with the PCB underneath. Also visible are the small PCBs holding the LED emitters and receivers for the internal and external detectors. DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 5 of 7 detail view of battery tray and internal antenna winding DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 6 of 7 Reverse of PCB showing infra red detector and emitter PCBs DSCF v2 FCC details FRN: 0019054196 FCC ID: XO9-DSCF003 Model ID: DSCF Page 7 of 7 Main PCBa assembly Component side with battery tray removed Reverse side of PCB Detail showing areas of change to the main PCBa from the iDSCF board. Red ring shows depopulated area of PCB

SureFlap Ltd Ground Floor Building 2030 , Cambourne Business park, Cambourne, CB23 8DW, United Kingdom Operating description FCC details FRN: 0019054196 FCC ID: XO9-DSCF1003 Model ID: DSCF v2 This device is a pet door with an integrated RFID reader that operates at 126 kHz or 133 kHz. The reader is normally used together with a sub-dermal RFID implant in the pet that is not provided with the product. The antenna is integrated into a short tunnel and may not be modified by the user. This tunnel goes through the door or wall that the pet door is installed in. The product has 2 read antennas and reacts to pets moving in both directions through the tunnel The pet door incorporates an infrared proximity detector that monitors for the presence of the pet. When the pet’s presence has been determined then the RFID reader tries to read the tag ID number and compares it to a previously stored list. If the ID tag matches one of the stored codes then a motorised lock is opened and the pet is allowed in or out. The button when pressed puts the device into a learn mode. In this mode when a pet goes through the door the reader reads the pet’s ID tag number and stores it in the list of allowed animals. This list can be wiped, if necessary, by holding down the same button. The device is battery powered and does not have any external connections. Yours faithfully, Dr. David Hallas, Managing Director

TÜV SÜD Product Service, Octagon House, Concorde Way, Segensworth North, Fareham, Hampshire, United Kingdom, PO15 5RL Tel: +44 (0) 1489 558100 Website: www.tuv-sud.co.uk COMMERCIAL-IN-CONFIDENCE SAR EXCLUSION DOCUMENT Approved by Date 20 July 2018 Simon Bennett Authorised Signatory 2018 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Product Service Page 1 of 4 Document 75941461-16 Issue 01 126 kHz and 133 kHz Transmitters: FCC Standalone SAR Test Exclusion Considerations (KDB 447498 D01) Section 4.3.1 c) <100 MHz – Separation Distance ≤50 mm or Separation Distance >50 mm and <200 mm The 1g head or body SAR test exclusion thresholds for <100 MHz are determined by the following steps: Step a) Threshold result from Formula in Section 4.3.1 a); [(max power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] [√f (GHz) ] ≤ 3.0 for 1g SAR.  f (GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison  When the maximum test separation distance is < 5 mm, a distance of 5 mm is applied. Step b) requires formula to be re-arranged to give power allowed at numeric threshold at 50 mm test separation distance and Step c) requires f (GHz) to be set to 100 MHz (0.1 GHz) giving: Step a) Power threshold = (3 * 50) / (√0.1) = 474.3 mW Step b) Threshold result from Formula in Section 4.3.1 b) 1); {[Power allowed at numeric threshold for 50 mm {Formula Step A})] + [(test separation distance – 50 mm)·(f (MHz) /150)]} mW  f MHz is the RF channel transmit frequency in MHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison Power threshold = 474.3 mW + [(test separation distance – 50 mm)·(f( MHz )/150)]} mW Step c) requires f (MHz) to be set to 100 MHz giving: Step b) Power threshold = 474.3 mW + [(test separation distance – 50 mm)·(100)/150)] mW COMMERCIAL-IN-CONFIDENCE DOCUMENT 75941461-16 Issue 01 CONTINUATION PAGE 2018 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Product Service Page 2 of 4 Step c) 1) Threshold result from Formula in Section 4.3.1 c) 1); >50 mm and <200 mm Threshold result from Formula in Section 4.3.1 b) 1) is multiplied by [1+log(100/f MHz )] Power threshold = [474.3 mW + (test separation distance – 50 mm)· (100)/150)] * [1+log(100/f MHz )] mW  f MHz is the RF channel transmit frequency in MHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison SAR Exclusion Result (1 g Head or Body) Frequency (MHz) Maximum Power (Tune up Value) * (mW) Test Separation Distance (mm) SAR Exclusion Power Threshold Section 4.3.1 c) (mW) SAR Test Exclusion (Yes/No) 0.126 438 199 2237 Yes 0.133 436 199 2224 Yes *Tune-up value is the maximum declared output power of the device derived from FCC Determination of the Equivalent Isotropically Radiated Power (EIRP) given in the measurement and calculations overleaf. The SAR exclusion threshold has been evaluated using the formula described above from information supplied by the manufacturer below. Based on the calculation above, the EUT is categorically excluded from SAR testing COMMERCIAL-IN-CONFIDENCE DOCUMENT 75941461-16 Issue 01 CONTINUATION PAGE 2018 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Product Service Page 3 of 4 FCC Determination of the Equivalent Isotropically Radiated Power (EIRP) of an RF Transmitting System (KDB 412172) Section 2.2 Direct calculation from the DUT power measured in a radiated test configuration Section 2.2. states: When the DUT power is measured using a radiated test configuration, the eirp can be directly determined using the field strength (linear) approach by applying Equation: eirp = p t x g t = (E x d) 2 /30  Eirp is the equivalent isotropically radiated power in watts.  p t transmitter output power in watts (not required)  g t numeric gain of the transmitting antenna (unitless) (not required)  E electric field strength in V/m  D measurement distance in meters (m) Measure the electric field strength E at test distance d m. If magnetic field strength is measured, convert to electric field strength in accordance with the antenna manufacturers’ conversion factors. Calculate the eirp using the equation above. Increase the eirp to include any declared tune-up tolerance value to give the maximum output power. The result is the Maximum Power (Tune up Value) required in the SAR exclusion assessment. Frequency kHz Magnetic Field Strength 1 (dBμA/m) Conversion Factor H to E Field 2 (dB) Electric Field Strength (dBμV/m) Electric Field Strength (V/m) Test Distance (m) Eirp (W) Eirp (mW) Tune-up Tolerance (%) Maximum Power (Tune up Value) (mW) 126 70.14 51.5 121.64 1.2078 3 4.3764E-01 437.64 0 438 133 70.12 51.5 121.62 1.2050 3 4.3563E-01 435.63 0 436 Note 1: Maximum magnetic field strength measured at 3 m from report 75941461_01. Note 2: Since Electric and magnetic fields are related by their wave impedance: E/H=377 ohms; E (dBμV/m) = H (dBμA/m) + 51.5 (dB) 377 ohms assumes worst case plane wave conditions for an inductive loop antenna, actual wave impedance would be lower giving lower result. COMMERCIAL-IN-CONFIDENCE DOCUMENT 75941461-16 Issue 01 CONTINUATION PAGE 2018 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Product Service Page 4 of 4 Manufacturer’s Declaration of Product information (extract):

TÜV SÜD is a trading name of TUV SUD Ltd Registered in Scotland at East Kilbride, Glasgow G75 0QF, United Kingdom Registered number: SC215164 TUV SUD Ltd is a TÜV SÜD Group Company Phone: +44 (0) 1489 558100 Fax: +44 (0) 1489 558101 www.tuv-sud.co.uk TÜV SÜD Octagon House Concorde Way Fareham Hampshire PO15 5RL United Kingdom TÜV SÜD RESPONSIBLE FOR NAME DATE SIGNATURE Project Management Natalie Bennett 02 December 2019 Authorised Signatory Matt Russell 02 December 2019 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD document control rules. ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC 47 CFR Part 15B and ICES-003. The sample tested was found to comply with the requirements defined in the applied rules. RESPONSIBLE FOR NAME DATE SIGNATURE Testing Graeme Lawler 02 December 2019 FCC Accreditation 90987 Octagon House, Fareham Test Laboratory Industry Canada Accreditation 12669A Octagon House, Fareham Test Laboratory EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC 47 CFR Part 15B: 2017 and ICES-003: 2016. Report on the FCC and IC Testing of the SureFlap Ltd Cat Flap Connect. Model: iDSCF In accordance with FCC 47 CFR Part 15B and ICES-003 Prepared for: SureFlap Ltd 7 The Irwin Centre Scotland Road Dry Drayton Cambridge Cambridgeshire CD23 8AR United Kingdom FCC ID: XO9-DSCF-1002 IC: 8906A-DSCF1002 COMMERCIAL-IN-CONFIDENCE Document Number: 75941461-04 | Issue: 03 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD. No part of this document may be reproduced without the prior written approval of TÜV SÜD. © 2019 TÜV SÜD. ACCREDITATION Our UKAS Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our UKAS Accreditation. Results of tests not covered by our UKAS Accreditation Schedule are marked NUA (Not UKAS Accredited). Document Number: 75941461-04 | Issue: 03 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 11 Contents 1 Report Summary .........................................................................................................................2 1.1 Report Modification Record ...........................................................................................................2 1.2 Introduction ....................................................................................................................................2 1.3 Brief Summary of Results .............................................................................................................3 1.4 Application Form ...........................................................................................................................4 1.5 Product Information .......................................................................................................................5 1.6 Deviations from the Standard ........................................................................................................5 1.7 EUT Modification Record ..............................................................................................................5 1.8 Test Location .................................................................................................................................5 2 Test Details ..................................................................................................................................6 2.1 Radiated Emissions.......................................................................................................................6 3 Measurement Uncertainty ....................................................................................................... 11 Document Number: 75941461-04 | Issue: 03 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 11 1 Report Summary 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Issue Description of Change Date of Issue 1 First Issue 12 July 2018 2 Up issue due to ISED Application deadline 23 August 2019 3 New ISED accreditation number for TUV SUD. Changing from IC2932B-1 to 12669A. 02 December 2019 1.2 Introduction Applicant SureFlap Ltd Manufacturer SureFlap Ltd Model Number(s) iDSCF Serial Number(s) Not Serialised (75941461-TSR0030) Hardware Version(s) 00500621-DA_02 Internet 00500621-DA_02 Internet DualScan Cat Flap General Assembly (_02: revision 02) Software Version(s) Firmware 01127_FF (but special version for TUV SUD testing) Number of Samples Tested 1 Test Specification/Issue/Date FCC 47 CFR Part 15B: 2017 ICES-003: 2016 Order Number Date 2265 19-January-2018 Date of Receipt of EUT 22-February-2018 Start of Test 26-May-2018 Finish of Test 28-May-2018 Name of Engineer(s) Graeme Lawler Related Document(s) ANSI C63.4 (2014) Document Number: 75941461-04 | Issue: 03 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 3 of 11 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with FCC 47 CFR Part 15B and ICES-003 is shown below. Section Specification Clause Test Description Result Comments/Base Standard Part 15B ICES-003 Configuration and Mode: Idle 2.1 15.109 6.2 Radiated Emissions Pass ANSI C63.4 (2014) Table 1 Document Number: 75941461-04 | Issue: 03 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 4 of 11 1.4 Application Form MAIN EUT MANUFACTURING DESCRIPTION Microchip Cat Flap Connect MANUFACTURER SureFlap Ltd MODEL NAME/NUMBER iDSCF PART NUMBER iDSCF SERIAL NUMBER see on the units HARDWARE VERSION 00500621-DA_02 Internet DualScan Cat Flap General Assembly (_02: revision 02) SOFTWARE VERSION Firmware 01…

Text truncated - open the document above for the full version.

TÜV SÜD is a trading name of TUV SUD Ltd Registered in Scotland at East Kilbride, Glasgow G75 0QF, United Kingdom Registered number: SC215164 TUV SUD Ltd is a TÜV SÜD Group Company Phone: +44 (0) 1489 558100 Fax: +44 (0) 1489 558101 www.tuv-sud.co.uk TÜV SÜD Octagon House Concorde Way Fareham Hampshire PO15 5RL United Kingdom TÜV SÜD RESPONSIBLE FOR NAME DATE SIGNATURE Project Management Natalie Bennett 19 December 2019 Authorised Signatory Ryan Henley 19 December 2019 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD document control rules. ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC 47 CFR Part 15C, Industry Canada RSS-210 and Industry Canada RSS-GEN. The sample tested was found to comply with the requirements defined in the applied rules. RESPONSIBLE FOR NAME DATE SIGNATURE Testing Mehadi Choudhury 19 December 2019 Testing Graeme Lawler 19 December 2019 FCC Accreditation 90987 Octagon House, Fareham Test Laboratory Industry Canada Accreditation 12669A Octagon House, Fareham Test Laboratory EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC 47 CFR Part 15C: 2017, Industry Canada RSS-210: Issue 09 (2016-08) Amd1 and Industry Canada RSS-GEN: Issue 05 (2018-04). Report on the FCC and IC Testing of the, SureFlap Ltd Cat Flap Connect. Model: iDSCF In accordance with FCC 47 CFR Part 15C, Industry Canada RSS-210 and Industry Canada RSS-GEN Prepared for: SureFlap Ltd 7 The Irwin Centre Scotland Road Dry Drayton Cambridge Cambridgeshire CD23 8AR United Kingdom FCC ID: XO9-DSCF-1002 IC: 8906A-DSCF1002 COMMERCIAL-IN-CONFIDENCE Document Number: 75941461-05 | Issue: 04 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD Product Service with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD Product Service. No part of this document may be reproduced without the prior written approval of TÜV SÜD Product Service. © 2019 TÜV SÜD Product Service. ACCREDITATION Our UKAS Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our UKAS Accreditation. Results of tests not covered by our UKAS Accreditation Schedule are marked NUA (Not UKAS Accredited). Document Number: 75941461-05 | Issue: 04 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 26 Contents 1 Report Summary .........................................................................................................................2 1.1 Report Modification Record ...........................................................................................................2 1.2 Introduction ....................................................................................................................................2 1.3 Brief Summary of Results .............................................................................................................3 1.4 Application Form ...........................................................................................................................4 1.5 Product Information .......................................................................................................................8 1.6 Deviations from the Standard ........................................................................................................8 1.7 EUT Modification Record ..............................................................................................................8 1.8 Test Location .................................................................................................................................8 2 Test Details ..................................................................................................................................9 2.1 Emission Bandwidth ......................................................................................................................9 2.2 Frequency Tolerance Under Temperature Variations ................................................................ 13 2.3 Transmitter Output Power .......................................................................................................... 15 2.4 Transmitter Unwanted Emissions ................................................................................…

Text truncated - open the document above for the full version.