XQC-WST132Wearable Action Button

Wrist Band (Top and Bottom) Surface Mount / Belt Clip WST-132 Wearable Ac Ɵ on Bu Ʃ on Instruc Ɵ ons and User Manual 1. Specifications Frequency: 345 MHz Operating Temp: 32° – 110°F (0° – 43°C) Operating Humidity: 0 – 95% RH non ‐ condensing Battery: 1x CR2032 Lithium 3V DC Battery Life: Up to 5 Years Compatibility: Honeywell, 2gig receivers Supervisory Interval: Approximately 7 0 minutes 2. Package Contents 1 x Action Button 1 x Rope Necklace 1 x Wrist Band 1 x Pendant Inserts (2 pcs) 1 x Manual 1 x CR2032 battery (included) 1 x Belt Clip Adapter 1x Surface Mount Bracket (w/ 2 screws) 3. Component Identification 4. Product Configuration The WST ‐ 132 can be worn or mounted in four (4 ways): 1. On a wrist using a compatible wrist band (the color of the included wrist band may vary). 2. Around the neck as a pendant using the included pendant inserts and snap ‐ closure adjustable ‐ length rope necklace (color may vary). 3. Mounted to a flat surface with the surface mount bracket and screws. 4. Worn on a belt with the surface mount bracket plus belt clip. Note: Users can personalize their Wearable Ac Ɵ on Bu Ʃ on with Apple Watch® ‐ compa Ɵ ble wristbands (38/40/41mm). 5. Enrolling The WST ‐ 132 Wearable Action Button supports up to three (3) different alerts or commands to be triggered through different button presses. The button appears as three sensor zones, each with their own unique serial number. To prepare the button: Install the battery in the action button following instructions in Section 8. Then Press and Hold the button for twenty (20) seconds. During this hold time, the LED will blink three times, then remain on for 3 more seconds [Zone 3]. Do not release the button, continue holding down the button until the LED blinks five (5) times indicating the button is ready. To enroll the action button : 1. Set your panel into programming mode according to the panel manufacturer’s instruction. 2. If prompted by the panel, enter the desired zone’s six ‐ digit ESN printed on the ESN card, following the panel manufacturer’s instructions. Note some panels can enroll your sensor by capturing the serial number transmitted by your sensor. For those panels, simply press the action button pattern for the desired Zone. Zone 1 Single Tap Press and Release (Once) Zone 2 Double Tap Press and Release (Twice, <1 second apart) Zone 3 Press and Hold Press and Hold until LED illuminates (about 5 seconds), then release. 3. When e nrolling the device, it is recommended to name each zone for easy identification and assignment to the intended action or scene. Example: zone #1 = “AB1 ST” (action button #1 single tap), zone #2 = “AB1 DT” (action button #1 double tap), and zone #3 = “AB1 PH” (action button #1 pr ess and hold). Important N o tes: After the zone is recognized by the panel, be sure to assign a zone type that is “chime only”. Otherwise, the button zone will be treated like a Door/Window open and restore and may trigger an alarm state. If the Ac Ɵ on Bu Ʃ on will be used as a “wearable device” super visory should be disabled on the panel, as the wearer may leave the premises. 4. Repeat steps 1 ‐ 3 until the panel recognizes all the desired Zones. 6. Action Button Testing The Ac Ɵ on Bu Ʃ on is designed to be used within 100 Ō . (30 m) of the panel. Test before fi rst use, as well as weekly. The test veri fi es proper communica Ɵ on between the sensor and the panel/receiver.To test the Ac Ɵ on Bu Ʃ on a Ō er enrollment, refer to the speci fi c panel/r eceiver documenta Ɵ on to place the panel into sensor test mode. Press the bu Ʃ on sequence for each zone to be tested, from loca Ɵ on(s) the Ac Ɵ on Bu Ʃ on shall be used. Verify the transmission count received on the panel is consistently 5 of 8 or be Ʃ er . 7. Product Operation The WST ‐ 132 Wearable Action Button supports up to three (3) different alerts or commands to be triggered through LED Ring Action Button Button Pendant Inserts (Top / Bottom) Rope Necklace CR2032 Battery different button presses. The button appears as three sensor zones, each with their own unique serial number (ESN). The LED Ring blink patte r ns confirm each button press type detected: Single Tap (Zone 1) Press and Release (Once) One short blink + On during transmission Double Tap (Zone 2) Press and Release (Twice, <1 second apart) Two short blinks + On during transmission Press and Hold (Zone 3) Press and Hold until LED illuminates (about 5 seconds), then release. Three short blinks + On during transmission The LED will remain on for approximately 3 seconds when transmitting. Wait until the LED is OFF before attempting the next button press. A Zone event transmission is sent as an Open immediately followed by a Restore. Depending on the security panel’s features, triggering each of the Action Button’s Zones can be set up as the initiating action to trigger a pre ‐ configured automation or rule. Refer to your specific panel’s instructions for more information. 8. Maintenance - Replacing the Battery When the ba Ʃ ery is low, a signal will be sent to the control panel. To replace the ba Ʃ ery:  Insert a plastic pry tool, or a small flat blade screwdriver into one of the notches on the back of the Action Button and gently pry to release the back cover from the main housing.  Set the back cover aside, and gently remove the circuit board from the housing.  Remove the old battery and insert a new Toshiba CR2032 or Panasonic CR2032 battery with the positive side (+) of the battery touching the battery holder marked with the (+) symbol.  Re ‐ assemble by placing the circuit board into the back case with the battery side facing down. Align the small notch on the side of the circuit board with the tallest plastic rib on the inside wall of the back case. When properly inserted, the circuit board will sit level inside back case.  Align the arrows of back cover and the main housing, then carefully snap them together.  Test the Action Button to ensure proper operation. WARNING: Fai…

Text truncated - open the document above for the full version.

01-20-2024 CETCB 114 Olinda Drive Brea, CA 92823 Gentlemen: This is a letter of authorization to accept Compatible Electronics, Inc., specifically including the employees of Compatible Electronics, as an Agent for Ecolink Intelligent Technology, 2055 Corte Del Nogal, Carlsbad, CA 92011, for a period of one year, to sign applications before the Commission on our behalf, to make representations to you on our behalf, and to receive and exchange data between our company and the Commission in connection with certification of the following Ecolink Intelligent Technology product: Model: WST-132 and RE203P Button Transmitter under FCC Docket Number 20780 and General Docket Number 80-284 pursuant to Part l5 of FCC Rules and Regulations. Please also accept this letter as an attestation that neither Ecolink Intelligent Technology nor any of its officers, directors, or persons holding 5% or more of the outstanding stock or shares, voting or non-voting, have been denied federal benefits under section 5301 of the Anti-Drug-Abuse act of 1988,21 U.S.C. 853(a). In addition, Ecolink Intelligent Technology will notify the Federal Communications Commission if, at any time, the situation changes causing Ecolink Intelligent Technology to be denied federal benefits. If you have any further questions or need additional information, please feel free to give me a call at (855)432-6546. Sincerely, Jay Stone Director of Engineering Ecolink Intelligent Technology 2055 Corte Del Nogal, Carlsbad, CA 92011

1 01-20-2024 Compatible Electronics TCB 114 Olinda Drive Brea, California 92823 Subject: TCB application submittal Gentlemen: We, Ecolink Intelligent Technology, would like to declare that the application being submitted for the device with FCC ID: XQC-WST132, has not been submitted to another TCB or FCC for certification. If you have any questi ons, please do not hesitate to contact us at (855)432-6546. Sincerely, Jay Stone Director of Engineering Ecolink Intelligent Technologies

01-20-2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 FCC ID: XQC-WST132 Subject: Attestation Statement pursuant to Part 2.911 (d)(7) Ecolink Intelligent Technology, Inc. “applicant”, as of the date of this filing, will also serve as the U.S. agent for service of process for the above reference FCC ID as required in Part 2.911(d)(7). The applicant acknowledges that they will maintain an agent for service of process for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. US Agent Company Name/Applicant: Ecolink Intelligent Technology, Inc. Contact Name: Jay Stone Address: 2055 Corte Del Nogal, Carlsbad, CA 920 11 Telephone Number: (855)432-6546 E-Mail: [email protected] FRN: 0019081256 Sincerely, Ecolink Intelligent Technology, Inc. Jay Stone Director of Engineering [email protected]

01-20-2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 FCC ID: XQC-WST132 Subject: Attestation Statements pursuant to Part 2.911 (d)(5)(i) Ecolink Intelligent Technology at 2055 Corte Del Nogal, CA 92011 certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules and according to FCC 22-84 and KDB 986446. Sincerely, Jay Stone Director of Engineering Ecolink Intelligent Technology 2055 Corte Del Nogal, Carlsbad, CA 92011 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

01-20-2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 FCC ID: XQC-WST132 Subject: Attestation Statements pursuant to Part 2.911 (d)(5)(ii) Ecolink Intelligent Technology, Inc.(“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List(as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Jay Stone Director of Engineering Ecolink Intelligent Technology 2055 Corte Del Nogal, Carlsbad, CA 92011

(1) 01-20-2024 Attention: Application Examiner RE: Request for Confidentiality Applicant: Ecolink Intelligent Technology FCC ID: XQC-WST132 To Whom It May Concern: Request is hereby submitted by Ecolink Intelligent Technology to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: Schematics Detailed Block Diagrams Detailed Operational/Functional Description Ecolink Intelligent Technology has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. The information contained in the confidential exhibits listed above is not available to the public. Sincerely, Jay Stone Director of Engineering Ecolink Intelligent Technology 2055 Corte Del Nogal, Carlsbad, CA 92011

Top Side of the EUT with Clip Bottom Side of the EUT with Clip Side View #1 of the EUT with Clip Side View #2 of the EUT with Clip Side View #3 of the EUT with Clip Side View #4 of the EUT with Clip Top View of the EUT with No Clip Bottom View of the EUT with No Clip - WST-132 Side View of the EUT #1 with No Clip Side View of the EUT #2 with No Clip Side View of the EUT #3 with No Clip Side View of the EUT #4 with No Clip

材質 比例 品號 規格 視角 日期 品名 繪圖 VISION MM 單位 版本 審核 承認 19mm 2 3 mm The FCC ID label material for this is: Adhesive is acrylic resin Substrate is white paper Ink printed 材質 比例 品號 規格 視角 日期 品名 繪圖 VISION MM 單位 版本 審核 承認 19mm 2 3 mm The FCC ID label material for this is: Adhesive is acrylic resin Substrate is white paper Ink printed

Compatible Electronics, Inc.https://celectronics.com 114 Olinda Drive Brea, CA 92823 This device FCC ID: Prepared By: Date: The maximum power that the transmitter is capable of is 0.18 mW Applied duty cycle? no Using the following formula from section 4.3.1 of KDB 447498 at test separation distances ≤ 50 mm [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] * [ √ f(GHz)] Duty Cycle 50.00% Value 1-g (mW) 10-g (mW) 0.02 152 535 "Value" shall be ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR 1-g power limit 10-g power limit 255 638 “source-based” time-averaging based on an inherent property or duty-cycle of a device is allowed. An example of this is the determination of exposure from a device that uses digital technology such as a time-division multiple-access (TDMA) scheme for transmission of a XQC-WST132 Max Peak Power (dBm) Min Separation distance (mm) * Frequency (Ghz) < 50mm power limits for above frequency and distance When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 0.345 5 -7.56 Kyle FujimotoFebruary 3, 2024 SAREXJUST-B-0-43 D 02/27/2020

Report Number: B40130D1 FCC Part 15 Subpart B and C; FCC Section 15.231; and RSS-210 and RSS-GEN Test Report Wearable Action Button Model: WST-132 Brea Division 114 Olinda Drive Brea, CA 92823 (714) 57 9-0 500 New bury Park Division 1050 Lawrence Drive Newbury Park, CA 91320 (805) 48 0-4 044 L ake Forest Division 20621 Pascal Way Lake Forest, CA 92630 (949) 58 7-0 400 Pa ge 1 of 21 FCC PART 15, SUBPART B and C; FCC 15.231; and RSS-210 & RSS-GEN TEST REPORT for WEARABLE ACTION BUTTON Model (HVIN): WST-132 Prepared for ECOLINK INTELLIGENT TECHNOLOGY, INC. 2055 CORTE DEL NOGAL CARLSBAD, CALIFORNIA 92011 Prepared by:_____________________ KYLE FUJIMOTO Approved by:____________________ JAMES ROSS COMPATIBLE ELECTRONICS INC. 114 OLINDA DRIVE BREA, CALIFORNIA 92823 (714) 579-0500 DATE: FEBRUARY 3, 2024 REPORT APPENDICES TOTAL BODY A B C D E PAGES 21 2 2 2 11 25 63 This report shall not be reproduced except in full, without the written approval of Compatible Electronics. Report Number: B40130D1 FCC Part 15 Subpart B and C; FCC Section 15.231; and RSS-210 and RSS-GEN Test Report Wearable Action Button Model: WST-132 Brea Division 114 Olinda Drive Brea, CA 92823 (714) 579-0500 Newbury Park Division 1050 Lawrence Drive Newbury Park, CA 91320 (805) 480-4044 Lake Forest Division 20621 Pascal Way Lake Forest, CA 92630 (949) 587-0400 Page 2 of 21 TABLE OF CONTENTS Section / Title PAGE GENERAL REPORT SUMMARY 4 SUMMARY OF TEST RESULTS 5 1. PURPOSE 6 1.1 Decision Rule & Risk 7 2. ADMINISTRATIVE DATA 8 2.1 Location of Testing 8 2.2 Traceability Statement 8 2.3 Cognizant Personnel 8 2.4 Date Test Sample was Received 8 2.5 Disposition of the Test Sample 8 2.6 Abbreviations and Acronyms 8 3. APPLICABLE DOCUMENTS 9 4. DESCRIPTION OF TEST CONFIGURATION 10 4.1 Description of Test Configuration – Emissions 10 4.1.1 Cable Construction and Termination 10 5. LISTS OF EUT, ACCESSORIES AND TEST EQUIPMENT 11 5.1 EUT and Accessory List 11 5.2 Emissions Test Equipment 12 6. TEST SITE DESCRIPTION 13 6.1 Test Facility Description 13 6.2 EUT Mounting, Bonding and Grounding 13 6.3 Measurement Uncertainty 13 7. TEST PROCEDURES 14 7.1 RF Emissions 14 7.1.1 Conducted Emissions Test 14 7.1.2 Radiated Emissions Test 15 7.1.3 RF Emissions Test Results 16 7.1.4 Sample Calculations 17 7.1.5 Duty Cycle Calculation 18 7.1.6 99 % Bandwidth 19 7.1.7 -20 dB Bandwidth 19 7.1.8 Transmission Time 20 7.1.9 Variation of the Input Power 20 8. CONCLUSIONS 21 Report Number: B40130D1 FCC Part 15 Subpart B and C; FCC Section 15.231; and RSS-210 and RSS-GEN Test Report Wearable Action Button Model: WST-132 Brea Division 114 Olinda Drive Brea, CA 92823 (714) 579-0500 Newbury Park Division 1050 Lawrence Drive Newbury Park, CA 91320 (805) 480-4044 Lake Forest Division 20621 Pascal Way Lake Forest, CA 92630 (949) 587-0400 Page 3 of 21 LIST OF APPENDICES APPENDIX TITLE A Laboratory Accreditations and Recognitions B Modifications to the EUT C Models Covered Under This Report D Diagrams, Charts, and Photos  Test Setup Diagrams  Antenna and Effective Gain Factors  Radiated Emissions Photos E Data Sheets LIST OF FIGURES FIGURE TITLE 1 Conducted Emissions Test Setup 2 Layout of the Semi-Anechoic Test Chamber LIST OF TABLES TABLE TITLE 1 Radiated Emission Results Report Number: B40130D1 FCC Part 15 Subpart B and C; FCC Section 15.231; and RSS-210 and RSS-GEN Test Report Wearable Action Button Model: WST-132 Brea Division 114 Olinda Drive Brea, CA 92823 (714) 57 9-0 500 New bury Park Division 1050 Lawrence Drive Newbury Park, CA 91320 (805) 48 0-4 044 L ake Forest Division 20621 Pascal Way Lake Forest, CA 92630 (949) 58 7-0 400 Pa ge 4 of 21 GENERAL REPORT SUMMARY This electromagnetic emission test report is generated by Compatible Electronics Inc., which is an independent testing and consulting firm. The test report is based on testing performed by Compatible Electronics personnel according to the measurement procedures described in the test specifications given below and in the "Test Procedures" section of this report. The measurement data and conclusions appearing herein relate only to the sample tested and this report may not be reproduced without the written permission of Compatible Electronics, unless done so in full. This report must not be used by the client to claim product certification, approval or endorsement by NVLAP, NIST or any agency of the United States government. Device Tested: Wearable Action Button Model (HVIN): WST-132 S/N: 1 Product Description: The equipment under test is a battery powered (a single CR2032 Lithium battery) wireless transmitter for home automation/security application. The transmit frequency is 345 MHz. The crystal oscillators are 4 MHz and 10.78125 MHz. Dimensions: 3.2 cm (W) x 1.5 cm (L) x 5.5 cm (H). Modifications: The EUT was not modified to meet the specifications. Customer: Ecolink Intelligent Technology, Inc. 2055 Corte Del Nogal Carlsbad, California 92011 Test Dates: January 29 and 30, 2024 Test Specifications covered by accreditation: Test Specifications: Emissions requirements CFR Title 47, Part 15, Subpart B; CFR Title 47, Part 15, Subpart C, sections 15.205, 15.209, and 15.231; RSS-210 and RSS-Gen Test Procedures: ANSI C63.4 and ANSI C63.10 Test Deviations: The test procedure was not deviated from during the testing. Report Number: B40130D1 FCC Part 15 Subpart B and C; FCC Section 15.231; and RSS-210 and RSS-GEN Test Report Wearable Action Button Model: WST-132 Brea Division 114 Olinda Drive Brea, CA 92823 (714) 57 9-0 500 New bury Park Division 1050 Lawrence Drive Newbury Park, CA 91320 (805) 48 0-4 044 L ake Forest Division 20621 Pascal Way Lake Forest, CA 92630 (949) 58 7-0 400 Pa ge 5 of 21 SUMMARY OF TEST RESULTS TEST DESCRIPTION RESULTS 1 Conducted RF Emissions, 150 kHz – 30 MHz This test was not performed because the EUT operates on battery power only and cannot be plugged into the AC public mains. 2 Spurious Radiated RF Emissions, 9 kHz – 3.45 GHz (Transmitter and Digital portion) Complies with the …

Text truncated - open the document above for the full version.

From measurement and conducted power, we have : 푃푃 푇푇 : 13 dBm (0.02 W) : 3 m E : 87.64 dBuV/m (0.0241 V/m) – peak value measured So, evaluated peak gain of the antenna, 푮푮 푻푻 = −20.6 풅풅풅풅풅풅 푃푃 푇푇 : Power transmitted in W 퐺퐺 푇푇 : Antenna Gain in that direction 푟푟: Distance in (m) Also, in terms of field strength, power density can be expressed as : 퐸퐸 2 푃푃 푑푑 = 푍푍 Here, 퐸퐸: Electric field strength in V/m : Free space impedance (377 ohms) Equating both the expressions above yields : : Power density in 푊푊 Here, 푃푃 푇푇 퐺퐺 푇푇 푃푃 푑푑 = 4휋휋푟푟 2 Peak gain is estimated from the measured peak Electric field value in the lab of 87.64 dBuV/m. We use the following expressions to evaluate the peak antenna gain from the measured Electric field. Power density at a given direction from a radiator : WST-132 & RE203P Antenna Spec Rev 1, 02/06/2024 The device uses a printed circuit antenna exhibiting a loop type structure and characteristics. The antenna is not accessible or changeable by the user. No modifications can be made to the radiating mechanism (antenna or tuning elements) by the user. The peak antenna gain is estimated to be -20.6 dBi. Worksheet for peak antenna gain estimation :

FRONT VIEW ECOLINK INTELLIGENT TECHNOLOGY, INC. WEARABLE ACTION BUTTON MODEL: WST-132 FCC SUBPART B AND C; RSS-210 AND RSS-GEN – RADIATED EMISSIONS – BELOW 1 GHz PHOTOGRAPH SHOWING THE EUT CONFIGURATION FOR MAXIMUM EMISSIONS REAR VIEW ECOLINK INTELLIGENT TECHNOLOGY, INC. WEARABLE ACTION BUTTON MODEL: WST-132 FCC SUBPART B AND C; RSS-210 AND RSS-GEN – RADIATED EMISSIONS – BELOW 1 GHz PHOTOGRAPH SHOWING THE EUT CONFIGURATION FOR MAXIMUM EMISSIONS FRONT VIEW ECOLINK INTELLIGENT TECHNOLOGY, INC. WEARABLE ACTION BUTTON MODEL: WST-132 FCC SUBPART B AND C; RSS-210 AND RSS-GEN – RADIATED EMISSIONS – ABOVE 1 GHz PHOTOGRAPH SHOWING THE EUT CONFIGURATION FOR MAXIMUM EMISSIONS REAR VIEW ECOLINK INTELLIGENT TECHNOLOGY, INC. WEARABLE ACTION BUTTON MODEL: WST-132 FCC SUBPART B AND C; RSS-210 AND RSS-GEN – RADIATED EMISSIONS – ABOVE 1 GHz PHOTOGRAPH SHOWING THE EUT CONFIGURATION FOR MAXIMUM EMISSIONS