XQC-WST401Garage Door Tilt Sensor

WST-401 Wireless Tilt Sensor Specifications Frequency: 319.5MHz Operating Temperature: -22° to 120°F (-30°to 49°C) Battery: One 3Vdc lithium CR123A (1550 mAh) Operating Humidity: 5-95% RH non condensing Battery life: 5-8 years Compatible with GE/Interlogix receivers Tilt Sensor Supervisory signal interval: 60 min (approx.) Enrolling To enroll the sensor, set your panel into program mode, then go to the Learn Sensors menu. Refer to your specific alarm panel manual for details on these menus. To activate the case tamper simply slide the cover up and down, you will hear a click when the case latches are engaging and disengaging. Continue until the panel responds to the sensor. Then select the appropriate sensor group and number. Tilt Sensitivity The tilt sensor will activate when the device is approximately at a 45 degree angle. By moving the actual ball sensor up or down you can adjust this angle by a few degrees. Note that this device has a delay of approximately 1 second to eliminate false alarms cause by wind and vibration commonly subjected to a large garage door. Mounting Included with this device are mounting screws and double sided tape. For reliable bonding with the tape ensure the surface is clean and dry. Apply the tape to the sensor and then to the desired location. Apply firm pressure for several seconds. It is not recommended to mount the tape at temperatures below 50°F, although after 24 hours the bond will hold at low temperatures. Replacing the Battery When the battery is low a signal will be sent to the control panel. To replace the battery: 1. Remove the screw securing the top cover, then remove the top cover to reveal the battery. 2. Replace with a CR123A battery ensuring the + side of the battery faces as indicated on the device. 3. Re-attached the cover and replace the screw to secure the cover. FCC Compliance Statement This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Re-orient or relocate the receiving antenna  Increase the separation between the equipment and receiver  Connect the equipment to an outlet on a different circuit from the receiver  Consult the dealer or an experienced radio/TV contractor for help. Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void the user’s authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de la dispositif. FCC ID:XQC-WST401 IC: 9863B-WST401 Warranty Ecolink Intelligent Technology Inc . warrants that for a period of 5 years from the date of purchase that this product is free from defects in material and workmanship. This warranty does not apply to damage caused by shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or as a result of any unauthorized modifications. If there is a defect in materials and workmanship under normal use within the warranty period Ecolink Intelligent Technology Inc. shall, at its option, repair or replace the defective equipment upon return of the equipment to the original point of purchase. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink Intelligent Technology Inc. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any warranty issue shall be limited to a replacement of the defective product . It is recommended that the customer check their equipment on a regular basis for proper operation. © 2014 Ecolink Intelligent Technology Inc. PN WST401 R1.00 2055 Corte Del Nogal Carlsbad, California 92011 1-855-632-6546 www.discoverecolink.com

External Photographs FCC ID: XQC-WST401 IC: 9863B-WST401

Label Artwork and label location on the product FCC ID: XQC-WST401 IC: 9863B-WST401

Internal Photographs FCC ID: XQC-WST401 IC: 9863B-WST401

This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TEST REPORT Report Number: 101773309LAX-001a Project Number: G101773309 Report Issue Date: November 25, 2014 Product Designation: Garage Door Tilt Sensor Model: WST-401 Standards: FCC ID: IC ID: FCC Part 15.231 Industry Canada RSS 210 Issue 8, December 2010 XQC-WST401 9863B-WST401 Tested by: Client: Intertek Testing Services NA, Inc. 25791 Commercentre Drive Lake Forest, CA 92630 USA Ecolink 2055 Corte Del Nogal Carlsbad, CA 92011 USA Report prepared by Report reviewed by Meak Nget EMC Engineering Supervisor Krishna K Vemuri EMC Senior Staff Engineer Intertek REPORT NUMBER: 101773309LAX-001a Issued: November 25, 2014 EMC Report for Ecolink on the Garage Door Tilt Sensor, model: WST-401 Page 2 of 29 TABLE OF CONTENTS 1 Introduction and Conclusion .............................................................................................................. 3 2 Test Summary ...................................................................................................................................... 3 3 Client Information ................................................................................................................................ 4 4 Description of Equipment Under Test ............................................................................................... 6 5 System setup including cable interconnection details, support equipment and simplified block diagram ........................................................................................................................................................ 7 6 Radiated Emissions (FCC Part 15.231) .............................................................................................. 8 7 AC Mains Conducted Emissions (FCC Part 15.207) ....................................................................... 27 8 Revision History ................................................................................................................................. 28 Intertek REPORT NUMBER: 101773309LAX-001a Issued: November 25, 2014 EMC Report for Ecolink on the Garage Door Tilt Sensor, model: WST-401 Page 3 of 29 1 Introduction and Conclusion The tests indicated in section 2.0 were performed on the product constructed as described in section 3.0. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test Method, a list of the actual Test Equipment Used, documentation Photos, Results and raw Data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested found compliant with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. 2 Test Summary TEST FCC REFERENCE IC REFERENCE Test Date RESULTS Radiated Emission 15.231(b) RSS-210 A1.1.2 08/06/2014 to 11/17/2014 Complies Out of Band Radiated Emission 15.231(b) RSS-210 A1.1.2 08/06/2014 to 11/17/2014 Complies AC Conducted Emission 15.207 RSS-Gen (6.1) Not Applicable* Not Applicable* 20 dB / 99% Bandwidth 15.231(c) RSS-210 A1.1.3 08/07/2014 Complies Transmitter Deactivation Time 15.231(a) RSS-210 A1.1.1(a) 08/07/2014 Complies Antenna Requirement 15.203 - 08/07/2014 Complies (*) Test not applicable due to the EUT being battery operated. Intertek REPORT NUMBER: 101773309LAX-001a Issued: November 25, 2014 EMC Report for Ecolink on the Garage Door Tilt Sensor, model: WST-401 Page 4 of 29 3 Client Information This EUT was tested at the request of: Company: Ecolink 2055 Corte Del Nogal Carlsbad, CA 92011 USA Contact Person: Mike Bailey Telephone: (877) 285-5448 Email: [email protected] 3.1 Overview of the EUT: Applicant: Ecolink Product Description: Model Number: Garage Door Tilt Sensor WST-401 FCC Identifier: IC Identifier: XQC-WST401 9863B-WST401 Transmitter activation: Manually operated. Deactivates within 5 seconds of being released. Fundamental Frequency (MHz): 319.5 MHz Antenna Requirement: The EUT uses a permanently connected internal antenna. Manufacturer name & address: Ecolink 2055 Corte Del Nogal Carlsbad, CA 92011 USA 3.2 Environmental Conditions: During the measurement the environmental conditions were within the listed ranges: Temperature: 10-40 ° C Humidity: 10-90 % Atmospheric pressure: 86-106 kPa Intertek REPORT NUMBER: 101773309LAX-001a Issued: November 25, 2014 EMC Report for Ecolink on the Garage Door Tilt Sensor, model: WST-401 Page 5 of 29 3.3 Measurement Uncertainty The measured value related to the corresponding limit will be used to decide whether the equipment meets the requirements. The measurement uncertainty figures were calculated and correspond to a coverage factor of k = 2, providing a confidence level of respectively 95% in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). The expanded uncertainty (k = 2) for radiated emissions from 30 to 1000 MHz has been determined to be: ±4.2 dB…

Text truncated - open the document above for the full version.

Setup Photographs FCC ID: XQC-WST401 IC: 9863B-WST401 Radiated Emissions Radiated Emissions