XQC-WST600Wireless Sensor

TM EC-FFV2- 433.92MHz AUDIO DETECTOR patent pending Installation Manual & Users Guide SPECIFICATIONS Frequency: 433.92MHz Operating Temperature: 32°-120°F (0°-49°C) Battery: One 3Vdc lithium CR123A (1550 mAh) Operating Humidity: 5-95% RH non condensing Battery life: 5 years Compatible with 433MHz DSC/Tyco Security Systems Detection distance: 6 in max Supervisory signal interval: 64 min(approx.) Maximum current draw: 23mA during transmission OPERATION The FireFighter™ sensor is designed to listen to any smoke, carbon or combo detector. Once confirmed as an alarm, it will transmit a signal to the alarm control panel which if connected to a central monitoring station, will dispatch the fire department. WARNING: This audio detector is intended only for use with smoke, carbon and combo detectors but it does not detect the presence of smoke, heat, or fire directly. ENROLLING (see IMAGE: 1) Manual Enroll Mode: There are 2 sequential serial numbers printed on the FF2 case, the first serial # is to be used if you intend to monitor for SMOKE and second for CARBON. By way of example 432565 (SERIAL # for Smoke) 432566 (SERIAL # for Carbon) Test for Correct Placement: Step 1: Insert the battery: The 1 st hour of power up allows easy testing via the test button on a Smoke, Carbon or Combo detector. After 1 hour it goes into a more stringent detection mode requiring multiple Temporal 3 or Temporal 4 patterns before it transmits. Step 2: Mount the Firefighter within 6 Inches of the Smoke, Carbon or Combo detector. Make sure the audio microphone (Side with the holes in it) is pointed to the Smoke, Carbon or Combo sounder. Press and HOLD the test button on the Smoke, Carbon or Combo detector. When the detector starts beeping the LED on the Firefighter will track Temporal 3 and or Temporal 4 patterns and transmit accordingly. The LED should be ON whenever the detector ‘Chirps’. If not, move the Firefighter closer to the detector. Use screws or provided double sided tape once you verify that the FF2 is tracking the sound of the detector. ***** It is possible that the FF2 can hear other smoke detectors in close proximity so it is important to choose and to install the FF2 close to a detector that is properly tracking and not hearing other detectors. FF2 is designed to work even if it hears other detectors but preferred install is close to a single detector. Typically smokes mounted in hallways could have an additional detector mounted in a close bedroom, simply verify that it is properly tracking and transmitting a signal to the panel when detector is triggered. MOUNTING (see IMAGE: 2 & 3) Included with this device is a mounting bracket, hardware and double sided tape. To ensure proper operation ensure the side of the device with the small holes is directly facing the sounder holes on the smoke detector. Secure the mounting bracket to the wall or ceiling using the two mounting screws and double sided tape provided, then secure the audio detector to the mounting bracket using the small screw provided. The FireFighter™ must be mounting within 6 inches of the detector for optimal operation. WARNING: Non-interconnected smoke detectors require an audio detector by each smoke detector sounder. This equipment should be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72, (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Printed information describing proper installation, operation, testing, maintenance, evacuation planning, and repair service is to be provided with this equipment. Warning: Owner’s instruction notice: ’Not to be removed by anyone except occupant’. TESTING (see IMAGE: 1) To test the RF transmission from the mounted position you can either generate a tamper by removing the cover or press the learn button located next to the tamper switch. Press and release ONCE to send a Smoke signal or press and HOLD for 2 seconds to send a Carbon signal. To test the audio detection, press and hold the smoke detector test button. Some Panels offer a Fire with Verification zone type. If this is the zone type programmed, you must press and hold the smoke detector button for at least 30 seconds to ensure that FireFighter™ has had sufficient time to identify the smoke alarm pattern and lock into alarm. Ensure the FireFighter™ cover is on and that you wear hearing protection. NOTE: This system must be checked by a qualified technician at least once every three (3) years. Please test the unit once per week to ensure proper functionality. Older NON temporal 3 Smoke Detectors If you happen to have an older NON temporal 3 pattern smoke detector you can change the Firefighter to be a universal listening device. When put into a universal listening pattern you must ensure that the Firefighter is not within listening distance of ANY Security alarm sirens or Alarm keypads. 1. Open the case, Remove the battery. 2. While holding the tamper switch IN, replace the battery, then release the tamper switch. This will toggle between Temporal and generic mode ONE flash: Temporal 3 and 4 mode (Will only trigger on Temporal Patterns) TWO flashes: Generic listening mode. (Will trigger after 30 seconds of continuous 3K frequency sounder) You can always verify the mode by simply removing the battery and replacing it. The LED will flash once or twice depending on the mode it is in. 3. When in generic, non-temporal 3 mode, the firefighter should not be installed in the same room as ANY alarm keypads or sirens. It is best to set the alarm off and make sure the RED LED on the firefighter does not hear any keypad or siren since it is looking for 30 seconds of continuous pattern at 3000-4000 Khz. If it does move the firefighter so it does not hear any siren or keypad that may be in the same room as the firefighter. WARNING: While the audio detector monitors its own battery, it does not monitor the battery in the smoke detectors. Batteries should be changed as per the original smoke detector …

Text truncated - open the document above for the full version.

Ecolink Intelligent Technology, Inc. Page 1 of 2 2055 Corte Del Nogal Carlsbad, CA 92011 October 27, 2014 UL Verification Services Inc. Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

Ecolink WST-600 Product ID Label Model #: WST-600 FCC ID: XQC-WST600 IC:9863B-WST600 Device: External, back view Adhesive sticker

FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS 210 CERTIFICATION TEST REPORT FOR WIRELESS SENSOR MODEL NUMBER: WST-600 FCC ID: XQC-WST600 IC: 9863B-WST600 REPORT NUMBER: 15U20415 REVISION A ISSUE DATE: May 5, 2015 Prepared for ECOLINK INTELLIGENT TECHNOLOGY, INC. 2055 CORTE DEL NOGAL CARLSBAD CA, 92011, U.S.A Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 2 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. Revision History Rev. Issue Date Revisions Revised By - 4/13/15 Initial P. Zhang A 5/5/15 Updated radiated measurement procedure; updated DCCF; Updated statement for radiated result P. Zhang REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 3 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 6 5. EQUIPMENT UNDER TEST ............................................................................................... 7 5.1. DESCRIPTION OF EUT .............................................................................................. 7 5.2. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 7 5.3. SOFTWARE AND FIRMWARE .................................................................................... 7 5.4. WORST-CASE CONFIGURATION AND MODE .......................................................... 7 5.5. MODIFICATIONS ........................................................................................................ 7 5.1. DESCRIPTION OF TEST SETUP ................................................................................ 8 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................10 7. ANTENNA PORT TEST RESULTS ...................................................................................11 7.1. 20 dB AND 99% BW ...................................................................................................11 7.2. DUTY CYCLE .............................................................................................................15 7.3. TRANSMISSION TIME ...............................................................................................21 8. RADIATED EMISSION TEST RESULTS...........................................................................22 8.1. TX RADIATED SPURIOUS EMISSION ......................................................................22 9. SETUP PHOTOS ...............................................................................................................30 REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 4 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: ECOLINK INTELLIGENT TECHNOLOGY, INC. 2055 CORTE DEL NOGAL CARLSBAD, CA, 92011, U.S.A EUT DESCRIPTION: WIRELESS SENSOR MODEL: WST-600 SERIAL NUMBER: 2056555 DATE TESTED: APRIL 8 – 13, 2015 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass INDUSTRY CANADA RSS-210 Issue 8, Annex 1 Pass INDUSTRY CANADA RSS-GEN Issue 4 Pass UL Verification Services Inc tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL Verification Services Inc By: Tested By: PENG ZHANG R.ALEGRE PROJECT LEAD LAB ENGINEER UL Verification Services Inc. UL Verification Services Inc. REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Pag…

Text truncated - open the document above for the full version.

REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 30 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. 9. SETUP PHOTOS ANTENNA PORT ANTENNA PORT REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 31 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION FOR PORTABLE CONFIGURATION – X ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – X ORIENTATION REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 32 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION FOR PORTABLE CONFIGURATION – Y ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – Y ORIENTATION REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 33 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION FOR PORTABLE CONFIGURATION – Z ORIENTATION RADIATED EMISSION FOR PORTABLE CONFIGURATION – Z ORIENTATION REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 34 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION BELOW 30 MHz RADIATED EMISSIONS BELOW 30MHz (FRONT) REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 35 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSIONS BELOW 30MHz (BACK) REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 36 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION ABOVE 30 MHz RADIATED EMISSIONS ABOVE 30 MHz (FRONT) REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 37 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSIONS ABOVE 30 MHz (BACK) RADIATED EMISSIONS ABOVE 1000 MHz (BACK) REPORT NO: 15U20415A DATE: May 5, 2015 FCC ID: XQC-WST600 IC: 9863-WST600 Page 38 of 38 UL VERIFICATION SERVICES INC FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. END OF REPORT RADIATED EMISSIONS ABOVE 1000 MHz (FRONT)