XR2WIZFI210Wireless LAN Module

WizFi210 User Manual (WIZnet Co., Ltd.) WizFi210/220 User Manual (Version 1.0) ©2011 WIZnet Co., Ltd. All Rights Reserved. ☞ For more information, visit our website at http://www.wiznet.co.kr WizFi210 User Manual (WIZnet Co., Ltd.) Certification Information CE for Class B ITE INFORMATION TO THE USER Hereby, WIZnet. Declares that this WizFi210 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. WARNING: This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC for Class B ITE INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no Guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. KCC for Class B ITE INFORMATION TO THE USER This equipment has been tested for a Class B digital device. - Trade Name or Applicant : WIZnet, Co., Ltd. - Equipment Name : Wireless LAN Module - Basic Model Number : WizFi210 - Derivative Model Number : WizFi210CA - Manufacturer / Country of Origin : WIZnet, Co., Ltd. / KOREA - Certification Number : KCC-CRM-WWW-WIZFI210 WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference. WizFi210 User Manual (WIZnet Co., Ltd.) Document Revision History Date Revision Changes 2011-03-24 V1.0 Official Release WizFi210 User Manual (WIZnet Co., Ltd.) <Contents> 1. Overview ........................................................................................................................ 1 (1) Benefits and Features .............................................................................................. 2 (2) Specifications .......................................................................................................... 3 2. Hardware Specification ................................................................................................... 4 (1) Operating Conditions .............................................................................................. 4 (2) Digital Input Specifications ...................................................................................... 4 (3) Digital Output Specifications ................................................................................... 4 (4) I/O Digital Specification (Tri-State) ........................................................................... 5 (5) RTC Input Specifications .......................................................................................... 6 (6) RTC Output Specifications ....................................................................................... 6 (7) Internal 1.8V regulator ............................................................................................ 7 (8) Power Consumption (VDD=3.3V, VDDIO=1.8V, Temp=25°C) .................................... 7 (9) RF Specification ....................................................................................................... 8 (10) Block Diagram ................................................................................................... 9 (11) Pin Description .................................................................................................. 9 (12) Module Dimension .......................................................................................... 13 (13) Recommend Pad Dimension............................................................................ 14 (14) LED Indications ............................................................................................... 14 (15) Application Circuit ........................................................................................... 15 (16) Interface ............................................... 오류! 책갈피가 정의되어 있지 않습니다. 3. Application Guide ......................................................................................................... 17 (1) AP Scanning .......................................................................................................... 17 (2) Network Connection Management ........................................................................ 17 (3) Auto Connection Operation .................................................................................. 17 (4) Response Codes .................................................................................................... 18 (5) Use of GPIO10 ...................................................................................................... 19 (6) AT Command example .......................................................................................... 20 4. AT Commands .................…

Text truncated - open the document above for the full version.

W5E-WO-03L Approval Sheet, WINiZEN Page 1 Check Check Approval Part No.W5E-WO-03L WiFi Dipole Antenna (2.4 GHz, Left-handed SMA) WINiZEN Co., Ltd. W5E-WO-03L Approval Sheet, WINiZEN Page 2 Revision History E D Date Author Description IR 2009.8.29 W.I.Kwak First issuance W5E-WO-03L Approval Sheet, WINiZEN Page 3 To: WIZNET Co., Ltd. Approval Sheet Product WiFi Dipole Antenna Model No. Manufacturer P/N W5E-WO-03L NO CODE DESCRIPTION REMARK 1 2.4 GHz WiFi Dipole Antenna Left-handed SMA 2 3 4 5 6 August 29, 2009 WINiZEN Co., Ltd. T205 Jinleekwan, 103-6 Munji-dong, Yuseong-gu, Daejeon-shi, Korea Tel: 042-866-6570, Fax: 042-866-6637 Issue Check Approval 2009/8/29 2009/8/29 W5E-WO-03L Approval Sheet, WINiZEN Page 4 - Contents – 1. Specifications 2. Mechanical Drawing 3. Test Method 3-1 Test Equipments 3-2 Test Equipment Setting 3-3 Calibration 4. Test Procedure 4-1 VSWR 4-2 Gain and Radiation Patterns 5. Measurement Data 5-1 VSWR 5-2 Return Loss 5-3 Smith Chart 5-4 Radiation Pattern 6. QC Process 7. Reliability Test 8. Packaging 9. RoHS Data W5E-WO-03L Approval Sheet, WINiZEN Page 5 1. Specifications Specifications Electrical Specifications Frequency Range 2400 ~ 2483.5 MHz Band Width 83.5 (MHz) V.S.W.R ( Min ) 1.9 : 1 Gain ( Max ) 2.5 ± 1 ( dBi ) Input Impedance 50 (Ω) Polarization Linear Mechanical Specifications Antenna Size See drawing Connector SMA Male (Left-handed) Operation Temperature -20 ~ 70 (°C) Operation Humidity 10 ~ 90 (%) Option Others W5E-WO-03L Approval Sheet, WINiZEN Page 6 1-5 2-5 3-5 4-5 5-5 2. Mechanical Drawing W5E-WO-03L Approval Sheet, WINiZEN Page 7 3. Test Method 3-1. Test Equipments Network Analyzer Agilent E8357A Calibration Kit Agilent E8357A Adaptor SMA Type Female ↔ SMA male Measurement Cable SPS-2801-400-SPS(Insulated Wire Inc.) 3-2. Test Equipment Setting Display Dual Channel : On Split Display : On Menu Number of Points : 201 Power : 0 dBm Measure Channel 1 : S11 Channel 2 : S21 3-3. Calibration Calibration- Cal. Kit : 50 Ω Calibration menu → Full-2 Port Reflection Forward : Open → Short → Load Reverse : Open → Short → Load Done Transmission Do Both → FWD + REV Done Isolation Omit Isolation Done W5E-WO-03L Approval Sheet, WINiZEN Page 8 4. Test Procedure 4-1. V.S.W.R Step 1. Connect the antenna to Port 1 of the Network Analyzer with a Cable Assembly. Step 2. Set Marker Pointer of the Network Analyzer to the target frequency. Step 3. Measure and check if the V.S.W.R. values are within 1.9. Step 4. Record Data. W5E-WO-03L Approval Sheet, WINiZEN Page 9 4-2. Gain and Radiation Patterns Step 1 Calibrate the Anechoic Chamber and Measurement System with a Dipole Antenna and a Horn Antenna. Prepare the Software Program to control the system. Step 2. Place the Antenna for measurement, on the location within the Anechoic Chamber. Step 3. Start the Software Program and Measurement. Step 4. Measure and record Data. W5E-WO-03L Approval Sheet, WINiZEN Page 10 5. Measurement Data Model Name W5E-WO-03L Engineer W.I.Kwak Antenna WiFi Dipole Antenna Frequency 2400 MHz ~ 2483.5 MHz Items Spec. Test Result Frequency 2400 MHz ~ 2483.5 MHz OK VSWR(Min) < 1.9 OK Gain(Max) 2.5±1.0 dBi OK W5E-WO-03L Approval Sheet, WINiZEN Page 11 5-1 VSWR 5-2 Return Loss W5E-WO-03L Approval Sheet, WINiZEN Page 12 5-4 Radiation Pattern a. Azimuth Pattern c. Elevation Pattern W5E-WO-03L Approval Sheet, WINiZEN Page 13 6. QC Process W5E-WO-03L Approval Sheet, WINiZEN Page 14 7. Reliability Test Item Specifications Conditions Test Result Salt-water Resistance No change of material characteristic Temperature of 35°C, Concentration of 5%, Let stand for 48 hours OK Humidity Resistance Changeable range of V.S.WR value± 0.5 No change of material characteristic Temperature of 40°C, Humidity of 95%, Let stand for 96 hours OK Temperature Test Temperature(°C) Changeable range of V.S.WR value± 0.5 No change of material characteristic Increasing from +25°C, 65% to +60°C, 30%; 35min / Keeping on +60°C, 30% for 6hour / Decreasing from +60°C, 30% to +40°C, 80%; 20min / Keeping on +40°C, 80% for 8hour / Decreasing from +40°C, 80% to -20°C, 0%; 60min / Keeping on -20°C, 0% for 4hour / Increasing from -20°C, 0% to 25°C, 65%; 45min / Keeping on 25°C for 3hour / 5Cycle time = 118hour and 20min OK Drop Antenna 1.5m Steel Plate (2t) No disconnection No crack or damage Drop the antenna at 1.5m height to the steel plate (2t) of ground OK W5E-WO-03L Approval Sheet, WINiZEN Page 15 8. Packaging

WIZNET Co., LTD. 4F Humax Village, 11-4 Sunae-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-825, Korea Date: April 14, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

WIZNET Co., LTD. 4F Humax Village, 11-4 Sunae-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-825, Korea Date: April 14, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: XR2WIZFI210 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, WIZNET Co., LTD. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give WIZNET Co., LTD. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description File name PERMANENT 1 Block Diagram Block Diagram_XR2WIZFI210.pdf 2 Operational Description Operational Description_XR2WIZFI210.pdf 3 Schematics Schematic_XR2WIZFI210.pdf 4 Part Lists Part List_XR2WIZFI210.pdf SHORT-TERM 5 External Photos Ext Photo_XR2WIZFI210.pdf 6 Internal Photos Int Photo_XR2WIZFI210.pdf 7 Test-Setup Photos Test Photo_XR2WIZFI210.pdf 8 Users Manual User Manual_XR2WIZFI210.pdf The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Byungkook Kim Senior Engineer

WIZNET Co., LTD. 4F Humax Village, 11-4 Sunae-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-825, Korea Date: April 14, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of DIGITAL EMC CO., LTD. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: XR2WIZFI210 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of DIGITAL EMC CO., LTD. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from WIZNET Co., LTD. Sincerely, Byungkook Kim Senior Engineer

1 Chris Harvey From: 이원정 <[email protected]> Sent: Tuesday, May 03, 2011 5:20 AM To: [email protected]; 'Chris Harvey -TCB' Cc: 'Harvey Sung' Subject: RE: WIZNET Co., LTD., //XR2WIZFI210 //AN11T0265 Attachments: RF Test Report-rev.1_XR2WIZFI210.pdf; User Manual_rev.1_XRZWIZFI210.pdf; Ext Photo- rev.1_XR2WIZFI210.pdf; Operational Description-rev.1_XR2WIZFI210.pdf Dear Chris, Thank you very much for your kindly information. I send the revised documents. If you have any question, please let me know. Best regards, Will 1. The Antenna Specification indicates the use of a 'left handed SMA', but the PC Board contains a UFLR connector. The photographs do not show how the antenna is connected to the board. Please add photos to the application showing how the antenna connects to this module, including any cables and adaptors. => Please refer to external photo. 2. Please confirm that this module contains on-board voltage regulation (the modular letter and the chip Operational Description are not clear). => The specification of voltage regulation is attached in operational description. Please refer to 57 page. 3. The User's Manual exhibit states that this module uses Radio Protocol 802.11 b/g/n Compatible with DSSS & CCK modulations at 11MB/s), the Operational Description states 802.11 b/g (no n) and the test report only documents 802.11b. Please confirm and update exhibits as needed. => This device supports only 802.11b. (The 802.11g is removed in user manual and operational description.) 4. The User's Manual states that this device has a Chip Antenna or external antenna. Since this device will not incorporate a chip antenna (Schematic & Parts list show DNI), the manual should be corrected. => A dipole antenna is supported. Not Chip antenna. The stated chip antenna in user manual is removed. 5. The User's manual contains a photograph on page 22 of 36 of some interface board. The Test Report page 36 of 40 shows the RF connector of this additional board for compliance with the Unique Connector requirements of FCC 15.203. 2 Please confirm if this additional board is provided with this device and if it was tested (this board is not shown in the EUT Internal/External photos). => The PC board is for testing. Therefore the board was used for testing. But the board is not included for approval. 6. This approval will be restricted to OEM installation for Mobile RF Exposure conditions and will not be allowed to be marketed directly to end users. => Yes, I agree. -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Friday, April 22, 2011 11:00 PM To: [email protected] Cc: [email protected] Subject: WIZNET Co., LTD., //XR2WIZFI210 //AN11T0265 Dear Harvey & Will, You are listed as the Technical Contacts for the above referenced TCB application. The following items need to be resolved before the review can be continued: 1. The Antenna Specification indicates the use of a 'left handed SMA', but the PC Board contains a UFLR connector. The photographs do not show how the antenna is connected to the board. Please add photos to the application showing how the antenna connects to this module, including any cables and adaptors. 2. Please confirm that this module contains on-board voltage regulation (the modular letter and the chip Operational Description are not clear). 3. The User's Manual exhibit states that this module uses Radio Protocol 802.11 b/g/n Compatible with DSSS & CCK modulations at 11MB/s), the Operational Description states 802.11 b/g (no n) and the test report only documents 802.11b. Please confirm and update exhibits as needed. 4. The User's Manual states that this device has a Chip Antenna or external antenna. Since this device will not incorporate a chip antenna (Schematic & Parts list show DNI), the manual should be corrected. 5. The User's manual contains a photograph on page 22 of 36 of some interface board. The Test Report page 36 of 40 shows the RF connector of this additional board for compliance with the Unique Connector requirements of FCC 15.203. Please confirm if this additional board is provided with this device and if it was tested (this board is not shown in the EUT Internal/External photos). 6. This approval will be restricted to OEM installation for Mobile RF Exposure conditions and will not be allowed to be marketed directly to end users. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application 3 dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Revised documentation should not be emailed, but instead should be submitted through "Add Attachment" function at the UL-CCS website. Please have your Assessment Number and FCC ID/IC Certification number handy. You may use the following link: https://cert.ccsemc.com/filing/ Best regards, Chris Harvey [email protected]

WIZNET Co., LTD. 4F Humax Village, 11-4 Sunae-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-825, Korea Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA April 14, 2011 Modular Approval Attestation for Wireless LAN Module Applicant: WIZNET Co., LTD. FCC ID: XR2WIZFI210 No. FCC requirements 1 Have its own RF shielding RF Block shielded by Metal Case 2 Have buffered modulation/data inputs (if such inputs are provided), Yes, the module has buffered data input. 3 The modular transmitter must have its own power supply regulation. We used self own power supply regulation. 4 Meet the antenna requirements of section 15.203 This module uses dipole antenna. This module meets the antenna requirements of section 15.203 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Yes, the EUT (module) was tested a stand alone configuration. 6 Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The proposed FCC ID label format is to be placed on the module. If FCC ID label is not visible when module is install into the system, “Contains FCC ID: XR2WIZFI210” shall be placed on the outside of final product. 7 The modular transmitter is manufactured so that the user can not influence the operation of the transmitter that will operate outside of the scope of the regulations. It complies with specific rules or operating requirements. And instruction is included User manual. 8 Address compliance with the Commission`s RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operation under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4) The output power of this device is much lower than the low threshold (60/f mW) of General Population which requires SAR. Sincerely, Byungkook Kim Senior Engineer

FCCID: XR2WIZFIZ210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 1 FCCID: XR2WIZFIZ210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 2 FCCID: XR2WIZFIZ210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 3 FCCID: XR2WIZFIZ210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 4

FCC ID: XR2WIZFI210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 2 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. CONTENTS 1. Equipment information .............................................................. 3 1.1 Equipment description ............................................................. 3 1.2 Ancillary equipment ................................................................. 3 2. Information about test items ..................................................... 4 2.1 Test mode ................................................................................ 4 2.2 Auxiliary equipment ................................................................. 4 2.3 Tested frequency ..................................................................... 4 2.4 Tested environment ................................................................. 4 2.5 EMI Suppression Device(s)/Modifications ............................... 4 3. Test Report ................................................................................. 5 3.1 Summary of tests .................................................................... 5 3.2 Transmitter requirements ........................................................ 6 3.2.1 6 dB Bandwidth ................................................................... 6 3.2.2 Peak Output Power ............................................................. 9 3.2.3 Out of Band Emissions / Band Edge ................................. 13 3.2.4 Out of band Emission – Radiated ..................................... 26 3.2.5 Transmitter Power Spectral Density .................................. 30 3.2.6 AC Conducted Emissions .................................................. 33 3.2.7 Antenna Requirements ...................................................... 36 APPENDIX..................................................................................... 37 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 3 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Digital Transmission System (DTS) Equipment type Wireless LAN Module Equipment model name WizFi210 Equipment add model name N/A Equipment serial no. Identical prototype Frequency band 2412 ~ 2462 MHz Modulation type CCK Channel Access Protocol CSMA/CA Channel Spacing 5.0 MHz Antenna type External Type: Dipole antenna (Max. Peak Gain: 3.377 dBi) Power Supply DC 3.3 V 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note - - - - - - - - - - 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 4 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 2. Information about test items 2.1 Test mode This device was tested in continuous transmitting mode at maximum power. Test Case 1 - Test Case 2 - 2.2 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note AC-DC Adapter DP05020DG N/A Green Power - - - - - - 2.3 Tested frequency TX Frequency (MHz) RX Frequency (MHz) Lowest Channel 2412 2412 Middle Channel 2437 2437 Highest Channel 2462 2462 2.4 Tested environment Temperature : 21 ~ 23 o C Relative humidity content : 32 ~ 52 % R.H. Details of power supply : DC 3.3 V AC-DC Adapter : 120 V 60 Hz 2.5 EMI Suppression Device(s)/Modifications EMI suppression device(s) added and/or modifications made during testing → None 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 5 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Limit (Using in 2400 ~ 2483.5MHz) Test Condition Status Note 1 I. Test Items 15.247(a)(2) 6 dB Bandwidth > 500 kHz Conducted C 15.247(b)(3) Transmitter Output Power < 1Watt C 15.247(c) Out of Band Emissions / Band Edge 20dBc in any 100kHz BW C 15.247(d) Transmitter Power Spectral Density < 8dBm / 3kHz C 15.205 15.209 General Field Strength Limits (Restricted Bands and Radiated Emission Limits) <FCC 15.209 Limits Radiated C 15.207 AC Conducted Emissions EN 55022 AC Line Conducted C 15.203 Antenna Requirements FCC 15.203 - C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable The sample was tested according to the following specification: ANSI C-63.4-2003, DA00-705 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 6 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 3.2 Transmitter requirements 3.2.1 6 dB Bandwidth - Procedure: The bandwidth at 6 dB below the highest inband spectral density was measured with a spectrum analyzer connected to the antenna terminal at the highest, middle and the lowest available channels. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 6dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 6 dB bandwidth of the emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest Frequencies Span = 50 MHz (Greater than EBW) RBW = 100 kHz Sweep = auto VBW = ≥ RBW Detector function = peak Trace = max hold - Measurement Data: Comply Test Mode Frequency Test Results (MHz) 802.11b Lowest 10.00 Middle 9.95 Highest 10.00 Note 1: See next pages for actual measured spectrum plots. - Minimum Standard: The minimum 6 dB bandwidth shall be at least 500 kHz 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 7 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 6 dB Bandwidth Test Mode: 802.11b & Lowest Frequency 6 dB Bandwidth Test Mode: 802.11b & Middle Frequency 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 8 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 6 dB Bandwidth Test Mode: 802.11b & Highest Frequency 1103-00308 DRTFCC1104-0174 TRF-RF-201(02)100714 Page 9 / 40 Copyright ○ C 2011, Digital EMC Co., Ltd. 3.2.2 Peak Output Power - Test Procedure and Spectrum Analyzer setting: The peak output power was measured with a spectrum analyzer conn…

Text truncated - open the document above for the full version.

FCC ID: XR2WIZFI210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. Tested EUT Position EUT position: X axis EUT position: Y axis EUT position: Z axis FCC ID: XR2WIZFI210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 1 FCC ID: XR2WIZFI210 Copyright Ⓒ 2011, DIGITAL EMC Co., Ltd. View 2