XS5-M77P19P19HPION-M7P/7P/19P/19HP 1900er path Block C

Optical Remote Unit ION™-M7P/7P/19P/19HP (W-cabinet) User's Manual MF0143AVA Manual for ION-M7P/7P/19P/19HP (W-Cabinet) Page 2 MF0143AVA ION-M7P-7P-19P-19HP W- Cab.doc © Copyright 2011 CommScope, Inc. All rights reserved. Andrew Solutions is a trademark of CommScope, Inc. All information contained in this manual has been revised thoroughly. Yet Andrew Solutions accepts no liability for any omissions or faults. Andrew Solutions reserves the right to change all hard- and software characteristics without notice. Names of products mentioned herein are used for identification purposes only and may be trademarks and / or registered trademarks of their respective companies. No parts of this publication may be reproduced, stored in a retrieval system, transmitted in any form or by any means, electronical, mechanical photocopying, recording or otherwise, without prior written permission of the publisher. Andrew Wireless Systems GmbH, 03-August-2011 Page 3 TABLE OF CONTENTS 1. GENERAL 5 1.1. USED ABBREVIATIONS 5 1.2. HEALTH AND SAFETY WARNINGS 7 1.3. ABOUT ANDREW SOLUTIONS 9 1.4. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 10 2. INTRODUCTION 12 2.1. PURPOSE 12 2.2. THE ION-M7P/7P/19P/19HP (INTELLIGENT OPTICAL NETWORK; MMR) 12 2.3. CHANNEL POWER DETECTION (CPD) OPTION 13 3. COMMISSIONING 14 3.1. MECHANICAL INSTALLATION 14 3.1.1. General 14 3.1.2. Wall-Mounting Procedure 16 3.2. ELECTRICAL INSTALLATION 17 3.2.1. General 17 3.2.2. Connections 18 3.2.3. Grounding 19 3.2.4. Connection of the Antenna Cables 19 3.2.5. Connection of AC Mains Power 20 3.2.6. Connection of Optical-Fibre-Cable - Rules 22 3.2.7. Protective Plug 23 3.2.8. Protective-Tube Kit 25 3.2.9. Connection of External-Alarms Cable 27 3.3. COMMISSIONING 28 4. ALARMS 32 4.1. BITE AND ALARMS 32 4.2. HANDLING OF ALARMS 32 4.3. ALARM STATUS 32 4.4. STATUS LED ALARMS 33 4.5. APPLICATION BOARD 34 4.5.1. External-Alarm Inputs and Outputs 34 4.5.2. Layout and Connector Description 36 4.6. TROUBLESHOOTING 38 5. MAINTENANCE 39 5.1. GENERAL 39 5.2. REPLACING THE FAN UNIT 40 User’s Manual for ION-M7P/7P/19P/19HP (W-cab) Page 4 MF0143AVA ION-M7P-7P-19P-19HP W- Cab.doc 5.3. CLEANING THE HEAT SINK 42 6. APPENDIX 43 6.1. ILLUSTRATIONS 43 6.2. SPECIFICATIONS 44 6.2.1. Electrical Specifications 44 6.2.2. Mechanical Specifications 44 6.2.3. Environmental and Safety Specifications 44 6.3. SPARE PARTS 45 7. INDEX 46 FIGURES AND TABLES figure 3-1 Wall mounting...........................................................................................16 figure 3-2 Connector flange of ION-M7P/7P/19P/19HP ............................................18 figure 3-3 Caution labels...........................................................................................18 figure 3-4 Grounding bolt with loosened hex nut, exemplary ....................................19 figure 3-5 Grounding bolt, schematic view................................................................19 figure 3-6 Position of AC mains connectors at connector flange..............................20 figure 3-7 AC mains plug, front view.........................................................................21 figure 3-8 Protective-plug assembly .........................................................................23 figure 3-9 Tube-kit installation...................................................................................26 figure 4-1 External-alarm inputs and outputs, location..............................................35 figure 4-2 Application board, connectors..................................................................36 figure 4-3 External-alarm outputs, relay contacts in alarm condition ........................37 figure 4-4 28 V DC connector, location on distribution board ...................................38 figure 6-1 Cabinet drawing........................................................................................43 table 1-1 List of international contact addresses.......................................................11 table 3-1 Specified torques.......................................................................................15 table 4-1 Status LED alarms .....................................................................................33 Page 5 MF0143AVA ION-M7P-7P-19P-19HP W- Cab.doc 1. GENERAL 1.1. USED ABBREVIATIONS 3GPP 3 rd Generation Partnership Project AC/DC Alternating current / Direct Current AIMOS Andrew Integrated Management and Operating System ALC Automatic Level Control BITE Built-In Test Equipment BTS Base Transceiver Station CE "Conformité Européenne" ("European Conformity") CD Compact Disk CPD Channel Power Detection DL Downlink DoC Declaration of Conformity EDGE Enhanced Data Rates for GSM Evolution EN European Norm EP Extension Port ESD Electrostatic Discharge ETS European Telecommunication Standard EU Extension Unit GSM Global System for Mobile Communication GND Ground GUI Graphical User Interface ICP3 Intercept Point 3 rd order ID No Identification Number ION Intelligent Optical Network IP Ingress Protection ISO International Organization for Standardization LED Light Emitting Diode LMT Local Maintenance Terminal LTE Long Term Evolution MIMO Multiple Input Multiple Output MS Mobile Station MU Main Unit NF Noise Figure OTRx Optical Transceiver = SRMU (Subrack Master Unit) PG Packing Gland PIM Passive Intermodulation R&TTE Radio & Telecommunications Terminal Equipment Rev Revision RF Radio Frequency RU Remote Unit RX Receiver SNMP Simple Network Management Protocol TS Technical Specification TX Transmitter Page 6 MF0143AVA ION-M7P-7P-19P-19HP W- Cab.doc UL Uplink UMTS Universal Mobile Telecommunication System UPS Uninterruptible Power Supply VSWR Voltage Standing Wave Ratio WCDMA Wideband Code Division Multiple Access WDM Wavelength Division Multiplex Page 7 MF0143AVA ION-M7P-7P-19P-19HP W- Cab.doc 1.2. HEALTH AND SAFETY WARNINGS 1. Only suitably qualified personnel is allowed to work on this unit and only after becoming familia…

Text truncated - open the document above for the full version.

NONDISCLOSURE AGREEMENT CTV.GEN.004.103006 Initials: ________ ________ Page 1 Agreement made this _____ day of _________, ______, by and between ___________________________, having a principal place of business at ___________________________________________ (“Recipient”), and CommScope, Inc. of North Carolina, having a principal place of business at 1100 CommScope Place, SE, Hickory, NC 28602 (“Discloser”). 1. The parties acknowledge that in furtherance of a mutual business interest Discloser may from time-to-time disclose to Recipient, or Recipient may be exposed to, certain Confidential Information as defined herein, in connection with the parties’ cooperation on the following project: (the “Project”). 2. For purposes of this Agreement, “Confidential Information” means all information not publicly available that is disclosed by Discloser to Recipient, including, without limitation, business or technical information, financial information, market forecasts, customer lists and other customer information, business plans, strategies, contract provisions, products, volumes, prices, product configurations, component specifications, logic diagrams, technical drawings, material properties, research and development, ideas, inventions (whether patentable or not), product development plans, processes, equipment designs and other information that Recipient would reasonably understand to be non-public and/or proprietary to Discloser. 3. Confidential Information shall not include any information that: a) Is or becomes part of the public domain through no improper action or inaction of Recipient or any of its affiliates or Representatives (as defined below); or b) Is known to Recipient or any of its affiliates prior to the disclosure by Discloser, and Recipient can prove such knowledge by documentation; or c) Is subsequently rightfully obtained by Recipient or any of its affiliates from a third party, unless Recipient knew or reasonably should have known that such third party had no right to disclose such information, or that such disclosure was in violation of a contractual or other duty of such third party to Discloser; or d) Is subsequently and independently developed by or for Recipient or any of its affiliates without any breach of this Agreement; or e) Is approved for public release in writing by Discloser. 4. Recipient shall use the Confidential Information only as necessary in connection with the Project and shall not use Confidential Information for its own sole benefit or for any reason detrimental to Discloser. Recipient shall hold the Confidential Information in complete confidence and will not disclose any of the Confidential Information except with the specific prior written consent of Discloser or otherwise as expressly permitted by this Agreement. Recipient may disclose Confidential Information only to its employees, agents, consultants, advisors or other representatives, including legal counsel, accountants and financial advisors (collectively, “Representatives”) who (i) require such Confidential Information in connection with the Project, and (ii) are informed by Recipient of the confidential nature of the Confidential Information and of Recipient’s obligations under this Agreement. Recipient agrees to be responsible for enforcing the terms of this Agreement as to its Representatives and to take such action, legal or otherwise, as may be necessary to cause its Representatives to comply with the terms hereof. Recipient shall restrict circulation of Confidential Information to the extent necessary to fulfill the purposes contemplated by this Agreement. Notwithstanding the foregoing, Recipient may disclose Confidential Information if and to the extent required by any applicable law, regulation, or judicial or regulatory action, provided that prior to any such disclosure Recipient shall provide Discloser with prompt written notice of such requirement and cooperate with Discloser to appropriately protect against or limit the scope of such disclosure. To the fullest extent permitted by law, Recipient will continue to protect as confidential and proprietary all Confidential Information disclosed pursuant to this paragraph. 5. Confidential Information shall remain at all times the property of Discloser. Upon receipt of Discloser's written request, Recipient will promptly return all or any requested portion of the Confidential Information (including, but not limited to, tangible and electronic copies, notes, summaries or extracts of any Confidential Information) to Discloser, or, in the alternative, Recipient will provide Discloser with written certification stating that such Confidential Information has been destroyed. One archival copy of documents evidencing the Confidential Information may be retained by Recipient’s counsel (including internal counsel) in a secure location for verification purposes only. 6. This Agreement or disclosures made hereunder shall not be construed as granting or conferring, either expressly or by implication, any interests or rights, by licenses or otherwise, to Recipient under any patent, copyright, trademark, service mark, trade name, trade secret or other intellectual property right of Discloser. The Confidential Information is provided “AS IS” without any warranties, including, but not limited to, warranties regarding the accuracy or utility of such Confidential Information, and Discloser hereby disclaims all such warranties. 7. Recipient hereby acknowledges that the Confidential Information provided under this Agreement is subject to export laws and regulations of the United States of America (“USA”) and any use or transfer of the Confidential Information must be authorized under those regulations. Recipient agrees that it will not use, distribute, transfer, or transmit the Confidential Information or any portion thereof (even if incorporated into other products) except in compliance with USA export regulations. If requested, Recipient also agrees to sign …

Text truncated - open the document above for the full version.

External pictures ION‐M7P/7P/19P/19HP Connections: with Description:

Label location ION‐M7P/7P/19P/19HP

Internal Pictures ION‐M7P/7P/19P/19HP Duplexer 700 Duplexer 1900 Frequency conversion module (FCM) Application board * Distribution board * * It isn’t possible to rem ove the Distribution‐ and Application board

RF Exposure Info / MPE Sample Calculation Model: ION‐M7P/7P/19P/19HP FCC‐ID: XS5‐M77P19P19HP The ION‐M7P/7P/19P/19HP is a fiber optic based RF repeater for wireless applications. An RF signal is converted to an optical signal by directly modulating a laser. There is no frequency conversion in this system. The optical signal is converted back to RF at the ION‐M remote unit, amplified and broadcast from an antenna or into a passive RF distribution system, such as radiating cable. The RF gain in the system is ma intained at a constant level throughout the system via AGC and the user does not need to adjust the gain of the system. The user would inject an RF signal to produce the appropriate RF output pow er from the ION‐M remote unit. The receive path will always terminate in an RF source, such as a base station or repeater, and will not be directly connected to any antenna. The specific device generally will be professionally installed. Hereby the gain of the finally installed antenna(s), cable attenuation and antenna height will be defined site specific at the time of licensing with the appropriate FCC Bureau(s). The maximum permissible exposure limit is defined in 47 CFR 1.1310 (B). Limits for General Population / Uncontrolled Exposures Frequency Range (MHz) Power Density (mW/cm 2 ) 300 – 1500 f/1500 The EUT operates in the 2 frequency bands: 700 and 1900 MHz. The lowest limit for Power Density is at the lowest frequency in the 700 MHz band. At 728 MHz the Power Density Limit is 2.423mW/cm 2 . The max measured conducted output power is 43.0 dBm (20 W) at the 700 MHz path. The maximum permitted level is to be calculated using general equation: S = P*G/4πR 2 P = 20W; G = antenna‐cable attenuation to be defined (numeric gain); π = 3,1416 The min separation distance between the antenna and any human body is to be calculated (solving for R in cm) with the final actual antenna gain/cable attenuation where the limit of 2.423 mW/cm 2 is kept. Example: For a antenna gain = 12 dBi the distance is R=2,82 m. Or for f=1930MHz (5 mW/cm 2 and P=46 dBm) and a gain = 12 dBi the distance is R = 2.241m. The antenna(s) used with device must be fixed‐mounted on permanent structures with a distance to any human body to comply with the RF Exposure limit.

Test Site: FCC Test Site No.: 96997 IC OATS No.: IC3475A-1 The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-EMC-TR-11-157-V01.00 Page 1 of 34 Date of issue: 15.07.11 Signature: Issue-No.: 01 Author: Tom Zahlmann Test engineer Date of delivery: 25.01.11 Checked: Mario Lehmann Head of the ECL Test dates: 07.06.11 – 14.06.11 Pages: 34 ECL-EMC Test Report No.: 11-157 ION-M7P/7P/19P/19HP 2x 700MHz path Equipment under test: XS5-M77P19P19HP FCC ID: 2237E-M77P19P19HP IC ID: FCC 47 CFR Part 27 Subpart H, F: 2011 Miscellaneous Wireless Communication Services IC RSS-131:2003 Zone Enhancers for the Land Mobile Service Type of test: Measurement Procedures: 47 CFR Parts 2:2011 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), Part 27:2011 (Miscellaneous Wireless Communication Services), ANSI/TIA-603-C:2004, Land Mobile FM or PM Communications Equipment Measurement and Performance Standards IC-GEN:2007 General Requirements and Information for the Certification of Radiocommunication Equipment Test result: Passed Test Report No.: 11-157 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full ANDREW Wireless Systems GmbH Manufacturer: Industriering 10 D-86675 Buchdorf Tel.: +49 (0)9099 69 0 Fax: +49 (0)9099 69 140 Test Location: TEMPTON Service Plus GmbH European Compliance Laboratory (ECL) Thurn-und-Taxis-Straße 18 D-90411 Nürnberg Tel.: +49 (0) 911 59835 0 Fax: +49 (0) 911 59835 90 General: General: The purpose of this report is to show compliance to the FCC regulations for devices operating under Part 27 of the Code of Federal Regulations title 47. The purpose of this report is to show compliance to the FCC regulations for devices operating under Part 27 of the Code of Federal Regulations title 47. This report informs about the results of the EMC tests, it only refers to the equipment under test. No part of this report may be reproduced in any form, without written permission. This report informs about the results of the EMC tests, it only refers to the equipment under test. No part of this report may be reproduced in any form, without written permission. without the written approval of the testing laboratory. ECL-EMC-TR-11-157-V01.00 Page 2 of 34 Test Report No.: 11-157 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-EMC-TR-11-157-V01.00 Page 3 of 34 Table of contents 1 TEST RESULTS SUMMARY .................................................................................................................5 2 EQUIPMENT UNDER TEST (E.U.T.) ....................................................................................................6 2.1 DESCRIPTION....................................................................................................................................6 2.1.1 DOWNLINK.................................................................................................................................6 2.1.2 UPLINK......................................................................................................................................6 2.1.3 DESCRIPTION OF EUT ................................................................................................................6 2.1.4 SYSTEM DIAGRAM OF EUT .........................................................................................................7 2.1.5 BLOCK DIAGRAM OF MEASUREMENT REFERENCE POINTS..............................................................7 3 TEST SITE (ANDREW BUCHDORF) ....................................................................................................8 3.1 TEST ENVIRONMENT..........................................................................................................................8 3.2 TEST EQUIPMENT..............................................................................................................................8 3.3 INPUT AND OUTPUT LOSSES...............................................................................................................8 3.4 MEASUREMENT UNCERTAINTY............................................................................................................8 4 TEST SITE (TEMPTON) ........................................................................................................................9 5 RF POWER OUT: §27.50, §2.1046; RSS-131, RSS-GEN ..................................................................10 5.1 LIMIT...............................................................................................................................................10 5.2 TEST METHOD.................................................................................................................................11 5.3 TEST RESULTS................................................................................................................................11 5.3.1 DOWNLINK...............................................................................................................................11 5.3.1.1 LTE 728 – 746MHz, MIMO.............................................................................................12 5.3.1.2 LTE 746 – 757MHz, MIMO.............................................................................................12 5.3.2 UPLINK....................................................................................................................................13 5.4 SUMMARY TEST RESULT...................................................................................................................13 6 OCCUPIED BANDWIDTH: §90.210, §2.1049; RSS-GEN...................................................................14 6.1 LIMIT.......................................................................................................................…

Text truncated - open the document above for the full version.

EMC Test Report No.: 11-158 Test Site: FCC Test Site No.: 96997 IC OATS No.: IC3475A-1 The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-158-V02.00 Page 1 of 45 Date of issue: 03.08.11 Signature: Issue-No.: 02 Author: T. Zahlmann Test engineer Date of delivery: 14.06.11 Checked: M. Lehmann Head of the ECL Test dates: 06.06. – 15.06.11 Pages: 45 ECL-TAL Test Report No.: 11-158 Equipment under test: ION-M7P/7P/19P/19HP 1900 MHz path Block A FCC ID: XS5-M77P19P19HP IC ID: IC:2237E-M77P19P19HP Type of test: FCC 47 CFR Part 24 Subpart E: 2011 Broadband PCS IC RSS-131 2 GHz Personal Communications Services Measurement Procedures: 47 CFR Parts 2: 2011 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 24 (Broadband PCS), ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards IC-GEN General Requirements and Information for the Certification of Radiocommunication Equipment EMC Test Report No.: 11-158 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-158-V02.00 Page 2 of 45 Manufacturer: ANDREW Wireless Systems GmbH Industriering 10 D-86675 Buchdorf Tel.: +49 (0)9099 69 0 Fax: +49 (0)9099 69 140 Test Location: TEMPTON Service Plus GmbH European Compliance Laboratory (ECL) Thurn-und Taxis-Straße 18 D-90411 Nürnberg Tel.: +49 0911 59835 23 Fax: +49 0911 59835 90 General: The purpose of this report is to show compliance to the FCC regulations for unlicensed devices operating under section 15.249 of the Code of Federal Regulations title 47. This report informs about the results of the EMC tests, it only refers to the equipment under test. No part of this report may be reproduced in any form, without written permission. EMC Test Report No.: 11-158 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-158-V02.00 Page 3 of 45 Table of contents 1 TEST RESULTS SUMMARY .................................................................................................................5 2 EQUIPMENT UNDER TEST (E.U.T.) ....................................................................................................6 2.1 DESCRIPTION....................................................................................................................................6 2.1.1 DOWNLINK.................................................................................................................................6 2.1.2 UPLINK......................................................................................................................................6 2.1.3 DESCRIPTION OF EUT ................................................................................................................6 2.1.4 SYSTEM DIAGRAM OF EUT .........................................................................................................7 2.1.5 BLOCK DIAGRAM OF MEASUREMENT REFERENCE POINTS..............................................................7 3 TEST SITE (ANDREW BUCHDORF) ....................................................................................................8 3.1 TEST ENVIRONMENT..........................................................................................................................8 3.2 TEST EQUIPMENT..............................................................................................................................9 3.3 INPUT AND OUTPUT LOSSES...............................................................................................................9 3.4 MEASUREMENT UNCERTAINTY............................................................................................................9 4 TEST SITE (TEMPTON SERVICE PLUS GMBH) ...............................................................................10 5 RF POWER OUT: §24.232, §2.1046 ...................................................................................................11 5.1 LIMIT...............................................................................................................................................11 5.2 TEST METHOD.................................................................................................................................11 5.3 TEST RESULTS................................................................................................................................12 5.3.1 DOWNLINK...............................................................................................................................13 5.3.1.1 GSM................................................................................................................................14 5.3.1.2 GSM EDGE ....................................................................................................................14 5.3.1.3 CDMA .............................................................................................................................15 5.3.1.4 W-CDMA.........................................................................................................................15 5.3.1.5 LTE .................................................................................................................................16 5.3.2 UPLINK....................................................................................................................................16 5.4 SUMMARY TEST RESULT...................................................................................................................16 6 OCCUPIED BANDWIDTH: §2.1049 ....................................................................................................17 6.1 LIMIT...........................................................…

Text truncated - open the document above for the full version.

EMC Test Report No.: 11-159 Test Site: FCC Test Site No.: 96997 IC OATS No.: IC3475A-1 The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-159-V02.00 Page 1 of 46 Date of issue: 03.08.11 Signature: Issue-No.: 02 Author: Tom Zahlmann Test engineer Date of delivery: 07.06.11 Checked: Mario Lehmann Head of the ECL Test dates: 07.06.11 – 14.06.11 Pages: 46 ECL-TAL Test Report No.: 11-159 Equipment under test: ION-M7P/7P/19P/19HP 1900er path Block C FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP Type of test: FCC 47 CFR Part 24 Subpart E: 2011 Broadband PCS IC RSS-131 2 GHz Personal Communications Services Measurement Procedures: 47 CFR Parts 2: 2011 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 24: 2011 (Broadband PCS), ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards IC-GEN: 2007 General Requirements and Information for the Certification of Radiocommunication Equipment Test result: Passed Test Report No.: 11-157 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-159-V02.00 Page 2 of 46 Manufacturer: ANDREW Wireless Systems GmbH Industriering 10 D-86675 Buchdorf Tel.: +49 (0)9099 69 0 Fax: +49 (0)9099 69 140 Test Location: TEMPTON Service Plus GmbH European Compliance Laboratory (ECL) Thurn-und Taxis-Straße 18 D-90411 Nürnberg Tel.: +49 0911 59835 23 Fax: +49 0911 59835 90 General: The purpose of this report is to show compliance to the FCC regulations for unlicensed devices operating under section 15.249 of the Code of Federal Regulations title 47. This report informs about the results of the EMC tests, it only refers to the equipment under test. No part of this report may be reproduced in any form, without written permission. Test Report No.: 11-157 FCC ID: XS5-M77P19P19HP IC ID: 2237E-M77P19P19HP The test report shall not be reproduced except in full without the written approval of the testing laboratory. ECL-TAL-TR-11-159-V02.00 Page 3 of 46 Table of contents 1 TEST RESULTS SUMMARY .................................................................................................................5 2 EQUIPMENT UNDER TEST (E.U.T.) ....................................................................................................6 2.1 DESCRIPTION....................................................................................................................................6 2.1.1 DOWNLINK.................................................................................................................................6 2.1.2 UPLINK......................................................................................................................................6 2.1.3 DESCRIPTION OF EUT ................................................................................................................6 2.1.4 SYSTEM DIAGRAM OF EUT .........................................................................................................7 2.1.5 BLOCK DIAGRAM OF MEASUREMENT REFERENCE POINTS..............................................................7 3 TEST SITE (ANDREW BUCHDORF) ....................................................................................................8…

Text truncated - open the document above for the full version.