XU8TEW751DRWireless Router

TEW-751DR 2x2 802.11a+b+g+n Dual Band Concurrent Wireless Router User’s Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -­‐ Reorient or relocate the receiving antenna. -­‐ Increase the separation between the equipment and receiver. -­‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -­‐ Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operations in the 5.15-­‐5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-­‐located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Note: The country code selection is for non-­‐US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN60950-­‐1: Safety of Information Technology Equipment EN 50385: (2002-­‐08) Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz -­‐ 40 GHz) -­‐ General public EN 300 328 V1.7.1 (2006-­‐10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-­‐1 V1.8.1 (2008-­‐04) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-­‐17 V2.1.1 (2009-­‐05) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-­‐user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-­‐user should contact the national spectrum authority in France. Česky [Czech] TRENDnet tímto prohlašuje, že tento TEW-­‐751DR je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-­‐751DR overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt TRENDnet, dass sich das Gerät TEW-­‐751DR in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab TRENDnet seadme TEW-­‐751DR vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, TRENDnet, declares that this TEW-­‐751DR is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente TRENDnet declara que el TEW-­‐751DR cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ TRENDnet ΔΗΛΩΝΕΙ ΟΤΙ TEW-­‐751DR ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente TRENDnet déclare que l'appareil TEW-­‐751DR est conforme aux exigences…

Text truncated - open the document above for the full version.

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310)961-5500 FAX: (310)961-5511 Date: 2012-01-06 Declaration for no non‐US channel operation We, TRENDNET, Inc., declare that the device does not support any non-US channels in all the operational mode(s) for the following product. Trademark: TRENDnet FCC ID: XU8TEW751DR If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310961-5500 FAX: (310)961-5511 2011-12-05 FCC ID: XU8TEW751DR Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ___________________________________ Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310961-5500 FAX: (310)961-5511 AUTHORIZATION LETTER 2011-08-11 To whom it may concern: We, the undersigned, TRENDNET, Inc. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required FCC and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------------------------- Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

LAN MAC: XXXXXXXXXXXX WAN MAC: XXXXXXXXXXXX/# S/N: Made in China FCC ID: XU8TEW751DR Power Input: 12V 1A This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)this device may not cause harmful interference and(2)this device must accept any interference received,including interference that may cause undesired operation. Model No.: TEW-751DR TRENDnet, Inc

Page 4 Page 5 Page 6 Page 7

FCC ID: XU8TEW751DR Report No.: RF111124C12 Operational Description This device is a Wireless Router, which operates in both of 2.4GHz and 5GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by the 12Vdc AC adapter. The antenna is Dipole antenna with UFL antenna connector. For more detailed instruction, please take a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA111124C12 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA111124C12 MODEL NO.: TEW-751DR FCC ID: XU8TEW751DR RECEIVED: Nov. 14, 2011 TESTED: Nov. 14 ~ Dec. 06, 2011 ISSUED: Dec. 09, 2011 APPLICANT: TRENDNET, Inc. ADDRESS: 20675 Manhattan Place, Torrance, CA 90501, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval, or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA111124C12 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. RF EXPOSURE............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)....................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................. 5 2.3 CLASSIFICATION ......................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER................................ 6 Report No.: SA111124C12 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Dec. 09, 2011 Report No.: SA111124C12 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: Wireless Router MODEL: TEW-751DR BRAND: TRENDnet APPLICANT: TRENDNET, Inc. TESTED: Nov. 14 ~ Dec. 06, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: TEW-751DR) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Dec. 09, 2011 Pettie Chen / Specialist APPROVED BY : , DATE: Dec. 09, 2011 Gary Chang / Technical Manager Report No.: SA111124C12 Report Format Version 4.0.0 5 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA111124C12 Report Format Version 4.0.0 6 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX CONDUCTED POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 25.5 2 20 0.111 1 5180-5240 16.1 2 20 0.013 1 5745-5825 24.7 2 20 0.093 1 CONCULSION: Both of the WLAN 2.4G & 5.0G can transmit simultaneously, the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density 1. WLAN 2.4G + WLAN 5.0G = 0.111+ 0.093= 0.204. Therefore, the maximum calculation of this situation is 0.204, which is less than the “1” limit.

Report No.: RF111124C12 1 Report Format Version 4.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF111124C12 MODEL NO.: TEW-751DR FCC ID: XU8TEW751DR RECEIVED: Nov. 14, 2011 TESTED: Nov. 14 ~ Dec. 06, 2011 ISSUED: Dec. 09, 2011 APPLICANT: TRENDNET, Inc. ADDRESS: 20675 Manhattan Place, Torrance, CA 90501, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 82 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111124C12 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.......................................................................................... 5 1. CERTIFICATION ....................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................... 7 2.1 MEASUREMENT UNCERTAINTY ............................................................................ 7 3. GENERAL INFORMATION........................................................................................ 8 3.1 GENERAL DESCRIPTION OF EUT .......................................................................... 8 3.2 DESCRIPTION OF TEST MODES.......................................................................... 10 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ..................................................... 11 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .......................... 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ......................................... 16 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................... 16 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND).............................................. 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT.................................. 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ............... 17 4.1.2 TEST INSTRUMENTS............................................................................................. 18 4.1.3 TEST PROCEDURES ............................................................................................. 19 4.1.4 DEVIATION FROM TEST STANDARD ................................................................... 19 4.1.5 TEST SETUP .......................................................................................................... 20 4.1.6 EUT OPERATING CONDITIONS ............................................................................ 20 4.1.7 TEST RESULTS ...................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT .......................................................... 34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................ 34 4.2.2 TEST INSTRUMENTS............................................................................................. 34 4.2.3 TEST PROCEDURES ............................................................................................. 35 4.2.4 DEVIATION FROM TEST STANDARD ................................................................... 35 4.2.5 TEST SETUP .......................................................................................................... 36 4.2.6 EUT OPERATING CONDITIONS ............................................................................ 36 4.2.7 TEST RESULTS ...................................................................................................... 37 4.3 6dB BANDWIDTH MEASUREMENT ...................................................................... 39 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................... 39 4.3.2 TEST SETUP .......................................................................................................... 39 4.3.3 TEST INSTRUMENTS............................................................................................. 39 4.3.4 TEST PROCEDURE ............................................................................................... 39 4.3.5 DEVIATION FROM TEST STANDARD ................................................................... 39 4.3.6 EUT OPERATING CONDITIONS ............................................................................ 39 4.3.7 TEST RESULTS ...................................................................................................... 40 4.4 CONDUCTED OUTPUT POWER ........................................................................... 41 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ............................ 41 4.4.2 TEST SETUP .......................................................................................................... 41 4.4.3 TEST INSTRUMENTS............................................................................................. 41 4.4.4 TEST PROCEDURES ............................................................................................. 41 4.4.5 DEVIATION FROM TEST STANDARD ................................................................... 41 4.4.6 EUT OPERATING CONDITIONS ............................................................................ 41 4.4.7 TEST RESULTS ...................................................................................................... 42 4.5 POWER SPECTRAL DENSITY MEASUREMENT.................................................. 43 4.5.1 LIMITS OF POWER …

Text truncated - open the document above for the full version.

Report No.: RF111124C12-1 1 Report Format Version 4.1.0 FCC TEST REPORT (15.407) REPORT NO.: RF111124C12-1 MODEL NO.: TEW-751DR FCC ID: XU8TEW751DR RECEIVED: Nov. 14, 2011 TESTED: Nov. 14 ~ Dec. 06, 2011 ISSUED: Dec. 09, 2011 APPLICANT: TRENDNET, Inc. ADDRESS: 20675 Manhattan Place, Torrance, CA 90501, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 49 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111124C12-1 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD..........................................................................................4 1. CERTIFICATION.......................................................................................................5 2. SUMMARY OF TEST RESULTS ..............................................................................6 2.1 MEASUREMENT UNCERTAINTY ...........................................................................6 3. GENERAL INFORMATION .......................................................................................7 3.1 GENERAL DESCRIPTION OF EUT.........................................................................7 3.2 DESCRIPTION OF TEST MODES...........................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .........................10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................12 3.4 DESCRIPTION OF SUPPORT UNITS ...................................................................12 4. TEST TYPES AND RESULTS ................................................................................13 4.1 RADIATED EMISSION MEASUREMENT ..............................................................13 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................13 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ..........13 4.1.3 TEST INSTRUMENTS ...........................................................................................14 4.1.4 TEST PROCEDURES ............................................................................................15 4.1.5 DEVIATION FROM TEST STANDARD ..................................................................15 4.1.6 TEST SETUP .........................................................................................................16 4.1.7 EUT OPERATING CONDITION .............................................................................16 4.1.8 TEST RESULTS .....................................................................................................17 4.2 CONDUCTED EMISSION MEASUREMENT .........................................................26 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT.......................................26 4.2.2 TEST INSTRUMENTS ...........................................................................................26 4.2.3 TEST PROCEDURES ............................................................................................27 4.2.4 DEVIATION FROM TEST STANDARD ..................................................................27 4.2.5 TEST SETUP .........................................................................................................28 4.2.6 EUT OPERATING CONDITIONS ...........................................................................28 4.2.7 TEST RESULTS .....................................................................................................29 4.3 PEAK TRANSMIT POWER MEASUREMENT .......................................................31 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT.....................................31 4.3.2 TEST SETUP .........................................................................................................31 4.3.3 TEST INSTRUMENTS ...........................................................................................31 4.3.4 TEST PROCEDURE ..............................................................................................32 4.3.5 DEVIATION FROM TEST STANDARD ..................................................................32 Report No.: RF111124C12-1 3 Report Format Version 4.1.0 4.3.6 EUT OPERATING CONDITIONS ...........................................................................32 4.3.7 TEST RESULTS .....................................................................................................33 4.4 PEAK POWER EXCURSION MEASUREMENT ....................................................35 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT..................................35 4.4.2 TEST SETUP .........................................................................................................35 4.4.3 TEST INSTRUMENTS ...........................................................................................35 4.4.4 TEST PROCEDURE ..............................................................................................35 4.4.5 DEVIATION FROM TEST STANDARD ..................................................................35 4.4.6 EUT OPERATING CONDITIONS ...........................................................................35 4.4.7 TEST RESULTS .....................................................................................................36 4.5 PEAK POWER SPECTRAL DENSITY ME…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST