XU8TEW804UBAC600 Dual Band Wireless USB Adapter

AC600 Dual Band USB Adapter TEW-804UB User’s Guide ii Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE: Radiation Exposure Statement: The product comply with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The USB dongle transmitter is approved for use in typical laptop computers. To comply with FCC RF exposure requirements, it should not be used in other devices or certain laptop and tablet computer configurations where the USB connectors on the host computer are unable to provide or ensure the necessary operating configurations intended for the device and its users or bystanders to satisfy RF exposure compliance requirements. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. For Taiwan 警語： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之 特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方 得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫 療用電波輻射性電機設備之干擾。 iii Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN60950-1: 2006+A11:2009+A1:2010+A12:2011 Safety of Information Technology Equipment EN 62311: 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300GHz) EN 301 893 V1.6.1: 2011 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive EN 300 328 V1.7.1 :2006-10 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.9.2 (2011-09) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.2.1 :2012-09 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevat…

Text truncated - open the document above for the full version.

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310961-5500 FAX: (310)961-5511 Date:2013-06-27 Declaration for no non‐US channel operation We, TRENDNET, Inc., declare that the device does not support any non-US channels in all the operational mode(s) for the following product. Trademark: TRENDnet FCC ID: XU8TEW804UB If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310961-5500 FAX: (310)961-5511 Declaration for DFS client devices Date: 2013-06-27 FCC ID: XU8TEW804UB Dear Examiner: Per KDB# 848637, We, TRENDNET, Inc., declare that following description truly represent our product in consideration. Please do not hesitate to contact us, if further info is required. Thanks. a). A channel/frequency plan for the device showing the channels that have active scanning or passive scanning. Active scanning is where the device can transmit a probe (beacon) and passive scanning is where the device can listen only without probes. Below is the channel / frequency plan for the device b). For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) or in different bands (devices with multiple equipment classes or those that operate on non‐DFS frequencies), or modular devices that configure the modes of operations through software; the applicant must provide in the application software and operations description that discuss how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by an end user or an installer. Also, include an attestation that the device complies with the CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 245224572462 Scan Type Active Active Active Active Active Active Active Active ActiveActiveActive CH 36 40 44 48 52 56 60 64 Frequency (MHz) 5180 5200 5220 5240 5260 5280 5300 5320 Scan Type Active Active Active Active PassivePassivePassive Passive CH 100 104 108 112 116 132 136 140 Frequency (MHz) 5500 5520 5540 5560 5580 5660 5680 5700 Scan Type Passive Passive PassivePassivePassivePassivePassive Passive CH 149 153 157 161 165 Frequency (MHz) 5745 5765 5785 5805 5825 Scan Type Active Active Active Active Active requirements for software configuration control as discussed in KDB #594280. On DFS channels, the WLAN driver on the device operates under the control of an AP at all times, except when in ad‐hoc mode, on US non‐DFS channels. As described in the answer to question a, the device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is locked by proprietary password and cannot be changed or modified by end user. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

2013-06-27 FCC ID: XU8TEW804UB Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ___________________________________ Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected] 20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310961-5500 FAX: (310)961-5511

20675 Manhattan Place, Torrance, CA 90501, USA TEL.: (310)961-5500 FAX: (310)961-5511 AUTHORIZATION LETTER Date:2013-06-27 To whom it may concern: We, the undersigned TRENDNET, Inc. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15C/E and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------------- Wen Tsai /Sr. Product Manager TRENDNET, Inc. TEL.: (310)961-5500 ext.5474 FAX: (310)961-5511 [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

Label location

S/N: MAC:XXXXXXXXXXXX/# Made in China Model:TEW-804UB REV.AV FCC ID:XU8TEW804UB "See Caution in Manual" TRENDnet, Inc

Page 2 Page 3 Page 4

FCC ID: XU8TEW804UB Report No.: RF130415C23 Operational Description This device is an AC600 Dual Band Wireless USB Adapter which operates in both of 2.4GHz and 5GHz bands; the maximum data rate could be up to 433Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 433Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by the 5Vdc from host equipment. The antenna is PIFA antenna with UFL antenna connector. For more detailed instruction, please take a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 25 Report No. : SA130223C15B Reference No.: 130223C15, 130415C23 Issued Date : Jun. 19, 2013 Revision : R01 FCC SAR Test Report Report No. : SA130223C15B Applicant : TRENDNET, Inc. Address : 20675 MANHATTAN PLACE, TORRANCE, CA 90501, USA Product : AC600 Dual Band Wireless USB Adapter FCC ID : XU8TEW804UB Brand : TRENDnet Model No. : TEW-804UB Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1991 / IEEE 1528:2003 FCC OET Bulletin 65 Supplement C (Edition 01-01) KDB 248227 D01 v01r02 / KDB 447498 D01 v05 / KDB 447498 D02 v02 Date of Testing : Mar. 28, 2013 ~ Mar. 30, 2013 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch - Taiwan HwaYa Lab, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 25 Report No. : SA130223C15B Reference No.: 130223C15, 130415C23 Issued Date : Jun. 19, 2013 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ................................................................................................................ 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 12 3.4 SAR Measurement Procedure ................................................................................................................................... 13 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 13 3.4.2 Volume Scan Procedure................................................................................................................................... 13 3.4.3 Power Drift Monitoring ...................................................................................................................................... 14 3.4.4 Spatial Peak SAR Evaluation .................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF130223C15B-2 1 of 24 Report Format Version 5.0.0 Reference No.: 130223C15, 130415C23 DFS TEST REPORT REPORT NO.: RF130223C15B-2 MODEL NO.: TEW-804UB FCC ID: XU8TEW804UB RECEIVED: Feb. 23, 2013 TESTED: Apr. 22, 2013 ISSUED: Apr. 22, 2013 APPLICANT: TRENDNET, Inc. ADDRESS: 20675 Manhattan Place, Torrance, CA 90501, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130223C15B-2 2 of 24 Report Format Version 5.0.0 Reference No.: 130223C15, 130415C23 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION ....................................................................................................................... 4 3. EUT INFORMATION ................................................................................................................. 5 3.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ...................................................... 5 3.2 EUT SOFTWARE AND FIRMWARE VERSION ....................................................................... 5 3.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT ..................................................... 5 3.4 EUT MAXIMUM CONDUCTED POWER .................................................................................. 6 3.5 EUT MAXIMUM E.I.R.P. POWER ............................................................................................. 7 3.6 TRANSMIT POWER CONTROL (TPC) .................................................................................... 8 3.7 STATEMENT OF MAUNFACTURER ........................................................................................ 8 4. U-NII DFS RULE REQUIREMENTS ......................................................................................... 9 4.1 WORKING MODES AND REQUIRED TEST ITEMS ................................................................ 9 4.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ............................................................. 10 5. TEST & SUPPORT EQUIPMENT LIST .................................................................................. 12 5.1 TEST INSTRUMENTS ............................................................................................................ 12 5.2 DESCRIPTION OF SUPPORT UNITS ................................................................................... 12 6. TEST PROCEDURE ............................................................................................................... 13 6.1 ADT DFS MEASUREMENT SYSTEM .................................................................................... 13 6.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: ................................................ 14 6.3 DEVIATION FROM TEST STANDARD ................................................................................... 15 6.4 CONDUCTED TEST SETUP CONFIGURATION ................................................................... 15 6.4.1 CLIENT WITHOUT RADAR DETECTION MODE .................................................................. 15 7. TEST RESULTS ...................................................................................................................... 16 7.1 SUMMARY OF TEST RESULTS ............................................................................................ 16 7.2 DETELED TEST RESULTS .................................................................................................... 17 7.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE.. 17 7.2.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME.................................. 18 7.2.3 NON-OCCUPANCY PERIOD ................................................................................................. 20 7.2.4 NON-ASSOCIATED TEST ...................................................................................................... 22 7.2.5 NON- CO-CHANNEL TEST .................................................................................................... 22 8. INFORMATION ON THE TESTING LABORATORIES ........................................................... 23 9. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ...............................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF130223C15B 1 of 81 Report Format Version 5.2.0 Reference No.: 130223C15, 130415C23 FCC TEST REPORT (15.247) REPORT NO.: RF130223C15B MODEL NO.: TEW-804UB FCC ID: XU8TEW804UB RECEIVED: Feb. 23, 2013 TESTED: Feb. 23 ~ Mar. 20, 2013 ISSUED: Apr. 17, 2013 APPLICANT: TRENDNET, Inc. ADDRESS: 20675 Manhattan Place, Torrance, CA 90501, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130223C15B 2 of 81 Report Format Version 5.2.0 Reference No.: 130223C15, 130415C23 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 5 1. CERTIFICATION ....................................................................................................................... 6 2. SUMMARY OF TEST RESULTS .............................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ............................................................................................ 7 3. GENERAL INFORMATION ....................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ......................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................................... 11 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................................... 15 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................... 15 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................ 16 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ............................................................. 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................................. 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............................. 17 4.1.2 TEST INSTRUMENTS ............................................................................................................ 18 4.1.3 TEST PROCEDURES ............................................................................................................. 19 4.1.4 DEVIATION FROM TEST STANDARD ................................................................................... 19 4.1.5 TEST SETUP .......................................................................................................................... 20 4.1.6 EUT OPERATING CONDITIONS ........................................................................................... 20 4.1.7 TEST RESULTS ...................................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................................... 34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ....................................................... 34 4.2.2 TEST INSTRUMENTS ............................................................................................................ 34 4.2.3 TEST PROCEDURES ............................................................................................................. 35 4.2.4 DEVIATION FROM TEST STANDARD ......................................................…

Text truncated - open the document above for the full version.