XZH-5580112020UVC Disinfecting Worklight

Use and Care GUide POrTaBLe UV-C disinfeCTinG WOrKLiGHT TrOUBLesHOOTinG Minor problems often can be fixed without the help of an electrician. WARNING: Before doing any work on the fixture, disconnect power to the light fixture. no.failure analysissolution 1 no beep (the indicator light is off) 1.Confirm whether it connect to the main power; 2.Confirm whether the remote control has a battery and whether the positive; and negative batteries are installed correctly; 3“UVC lamp” can not turn on Confirm whether the lamp is powered on. if the lamp is powered on, confirm the remote control is operating correctly. WARNING 1. UVC exposure is harmful to humans and animals. Prevent any exposure by leaving prior to the unit turning on. 2. in severe cases, headache, dizziness, increased body temperature, eye irritation, or decreased vision, skin irritation, itching, swelling, etc. Please consult your doctor immediately. AddItIoNAl Note: 1. The product cannot be used for lighting purposes. 2. This product is only intended for disinfecting surface objects and surrounding air. This product is not to be used to disinfect the human body and can be dangerous to humans and animals 3. Use with caution damage can occur to objects that are not resistant to ultraviolet rays. 4. after disinfecting, please put away the product and the remote control to avoid accidental light on and accidental injury. 5. if UV disinfecting lamp is accidently broken handle with extreme care. Ventilate the area and use gloves to clean up, The lamp contains mercury do not vacuum up with a standard vacuum cleaner as it can create dust & mercury vapor. 6. if the lamp accidentally touches skin wash thoroughly, handle broken glass with gloves. FCC StAtemeNt This device complies with Part 15 of the fCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the fCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general rf exposure requirement. The device can be used in portable exposure condition without restriction. WARRANty This product is warranted for a period of 2 years from the date of original purchase against defects in materials and workmanship. if this product should fail to operate due to defects in material or workmanship within 24 months of purchase, see www.eTissL.com for details. This product will be repaired or replaced, at eTi’s option. This warranty is expressly limited to repair or replacement of product, and liability for direct, incidental, or consequential damages is hereby expressly excluded. some states do not allow exclusions of direct, incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty gives the consumer specifc legal rights, which vary from state to state. WarranTY is VOid if PrOdUCT is nOT Used fOr THe PUrPOse WHiCH THis PrOdUCT is ManUfaCTUred. TeCHniCaL sPeCifiCaTiOns PreCaUTiOns fOr Use 1. Only professional maintenance is allowed, so as not to damage the precision electronic components. 2. if the ambient temperature is too high (above 95°f), the microwave sensing distance will be shortened. at the same time, there is a possibility that the lamp is turned off by mistake, avoid installing the lamp in direct air flow location (such as: cold / hot water outlet, exhaust fan, near the electric furnace, etc.). The sensor head cannot be blocked or covered otherwise there will be a risk of Pir sensor failure. 3. Multiple lights need to be separated by more than 5 ft to prevent unwanted detection. PaCKaGe COnTenTs and insTrUCTiOns Partdescription Quantity aUVC Worklight1 B9 ft. Power Cord1 UVC LaMP sUGGesTed area and TiMe room size (ft 2 )suggested Operating Time (mins) 50 sQfT (5’x10’)15 120 sQfT (10’x12’)30 a On/Off Turn Off Turn Off Turn On Microwave sensor indicator Light Turn On Lock B B 1/22/2 insTaLLaTiOn 1. Plug in the power cord. 2. Turn child lock off. 3. Choose the lighting time (15min/30min) according to the disinfection space. 4. Leave the lamp at least 12 ft. within 20 seconds after setting mode. aa fOr assisTanCe, CaLL: Customer service Line 8 a.m. - 5 p.m., CsT, Monday - friday 1-855-eTi-ssLi (1-855-384-7754) 720 northgate Parkway Wheeling, i L 60090 retain this manual for future use. a On/Off 15 minute 15 minute 30 minute 30 minute sensor detection distance: 13.7 ft. WARNING: UV emitted from this product. Avoid eye and skin exposure to unshielded product. REMARK: The result is tested against the IEC62471 at distance 13.7 ft. Risk Group 3 CaUTiOn: Prior to turning on this disinfecting work light has a intermittent or continuous beep and warning light feature. This is a warning to leave the …

Text truncated - open the document above for the full version.

DATE :2020.12.29 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: _ XZH-5580112020__ Product Name: _ UVC Disinfecting Worklight _____ Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Sean Luo Title: Dept. Manager Applicant Company: ETI Solid State Lighting (Zhuhai) Ltd

Date：2020.12.29 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: Sean Luo Title: Dept. Manager Applicant Company: ETI Solid State Lighting (Zhuhai) Ltd

DATE: 2020.12.29 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Dongguan New Testing Centre Co., Ltd；3F, No. 1 the 1st North Industry Road, Songshan Lake Science & Technology Park, Dongguan, Guangdong, China, 523808. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ETI Solid State Lighting (Zhuhai) Ltd； No.1, Zhongzhu Road South, Science & Technology Innovation Coast, High Tech District, Zhuhai City, Guangdong Prov., China <Signature> Name: Sean Luo Title: Dept. Manager Applicant Company: ETI Solid State Lighting (Zhuhai) Ltd

External photos Model: 558011000

Label and label location Model: 558011000

Internal Photos Model: 558011000 Antenna

Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 3F, No. 1 the 1st North Industry Road, Songshan Lake Science & Technology Park, Dongguan, Guangdong, China, 523808 Page 1 of 27 Report No.:NTC-ER2012005 FCC TEST REPORT Report No. ...................................... : NTC-ER2012005 Applicant’s name ........................... : ETI Solid State Lighting (Zhuhai) Ltd Address ............................................ : No.1, Zhongzhu Road South, Science & Technology Innovation Coast, High Tech District, Zhuhai City, Guangdong Prov., China Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 3F, No. 1 the 1st North Industry Road, Songshan Lake Science & Technology Park, Dongguan, Guangdong, China, 523808 Page 1 of 27 Report No.:NTC-ER2012005 TABLE OF CONTENTS Test Report Declare ...................................................................................................................... 3 1. Summary of test results ........................................................................................................... 3 2. General test information .......................................................................................................... 3 2.1. Description of EUT ................................................................................................................... 3 2.2. Support Equipment ................................................................................................................... 4 2.3. Block diagram EUT configuration for test ............................................................................. 4 2.4. Test environment conditions ................................................................................................... 4 2.5. Measurement uncertainty ........................................................................................................ 4 3. Power Line Conducted Emission Test .................................................................................. 5 3.1. Test equipment ......................................................................................................................... 5 3.2. Block diagram of test setup ..................................................................................................... 5 3.3. Power Line Conducted Emission Limits (Class B) .............................................................. 5 3.4. Test Procedure .......................................................................................................................... 6 3.5. Test Result ................................................................................................................................. 6 4. Radiated emission test ............................................................................................................. 9 4.1. Test equipment ......................................................................................................................... 9 4.2. Block diagram of test setup ................................................................................................... 10 4.3. Limit .......................................................................................................................................... 12 4.4. Test Procedure ........................................................................................................................ 13 4.5. Test result ................................................................................................................................ 13 5. -20dB and 99% Bandwidth .................................................................................................... 19 5.1. Test equipment ....................................................................................................................... 19 5.2. Block diagram of test setup ................................................................................................... 19 5.3. Limit .......................................................................................................................................... 19 5.4. Test Procedure ........................................................................................................................ 19 5.5. Test result ................................................................................................................................ 20 6. Antenna Requirements .......................................................................................................... 22 6.1. Limit .......................................................................................................................................... 22 6.2. Result........................................................................................................................................ 22 7. Test setup photograph ........................................................................................................... 23 7.1. Photos of power line conducted emission test ................................................................... 23 7.2. Photos of radiated emission test .......................................................................................... 23 8. Photos of the EUT .................................................................................................................. 25 Dongguan New Testing Centre Co., Ltd E-mail： [email protected] 3F, No. 1 the 1st North Industry Road, Songshan Lake Science & Technology Park, Dongguan, Guangdong, China, 523808 Page 2 of 27 Report No.: NTC-ER2012005 TEST REPORT DECLARE Test Standard Used: FCC Rules and Regulations Part 15 Subpart C: 2017, ANSI C63.10:2013. RSS-210: Issue 10 December 2019, RSS-Gen: March 6, 2019. We Declare: The equipment described above is tested by Dongguan New Testing Centre Co., Ltd and in the configuration tested the equipment complied with the standards specified above. The test results are contained in this test rep…

Text truncated - open the document above for the full version.

Setup photos Model No: 558011000 Conducted emission test Radiated emission test 30MHz – 1GHz Above 1GHz