XZHELECTECH1Induction cooker

Cooks Induction Cooker Lot# 780-2402 INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using Electrical appliance, basic safety precautions should always be followed including the following. 1. Read all instructions before use. 2. DO NOT touch the hot surfaces. Use handles and knobs. 3. Use unit only on a level surface. 4. Use only with induction-compatible cookware. 5. Dry outside of the pan before use. 6. Do not heat empty pan. 7. Do not spill any liquids into vent areas. 8. TO protect against electrical shock, do not immerse cord, plugs or housing unit in water or other liquids. 9. This appliance should not be used by or near children or individuals with certain disabilities. 10. Do not leave appliance unattended when it is on. 11. Unplug from wall outlet when not in use and before cleaning. 12. Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or has been damaged in any manner. Call the toll-free NO. to return for examination, repair or adjustment. 13. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. 14. Do not use outdoors or while standing in a damp area, 15. Do not let cord hang over the edge of the table or counter, or touch hot surface 16. Do not place on or near a hot gas or electric burner, or in a heated oven. 17. Extreme caution must be used when moving any pot or pan containing hot oil or other hot liquids from this appliance. 18. When using this appliance proved at least 4-6 inches of air space above and on all sides for air circulation. 19. Do not use this appliance for any other than its intended use. This appliance is for household use only. 20. To disconnect, turn the unit off, then remove plug from wall outlet. 21. Do Not Cooks on Broken Cook Top-If cook-top should break, cleaning solutions and spillovers may penetrate the broken cook-top and create a risk of electric shock 22. Clean Cook-Top with caution, -If a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful to avoid steam burn, some cleaners can produce noxious if applied to a hot surface. 23. Save these instructions. SAVE THESE INSTRUCTIONS! WARNING Short Power Cord Instructions A short powersupplier cord (or detachable powersupply cord) is to be provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If a longer detachable power-supply cord or extension cord is used: 1) The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance and 2) The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally. POLARIZED PLUG This appliance has a polarized plug (one blade is wider than the other).To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. FCC requirements Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: ● This equipment has been tested and found to comply with the limits for Class B ISM equipment, pursuant to Part 18 of the FCC Rules. ● These limits are designed to provide reasonable protection against harmful interference in a residential installation. ● This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation。 ● If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio TV technician for help. Read your Use& Care booklet thoroughly before using your Induction Cooker for the first time. Failure to follow the guidance provided by the Use &Care will void the warranty. Features & Specification Features Pollution free: No burning, no smoke or detrimental gases Safe: no flame, no exhaust Easy to clean-high rigidity quartz cooking plate Energy efficient- Use up to 30% less power than conventional cooktop Power selection from 200W to 1300W Automatic shutoff- turns off 30 seconds after pan is removed Overheat protection Timer function: up to 2 hours 59 minutes timer. Specification: Model Rating Voltage Rower rating Power range 780-2402 120V AC/60Hz 1300W 200W-1300W Using Your Induction Cooker Before first use
Remove all packaging materials, labels including the plastic film on the control Panel-and/or stickers from your induction cooker.
Clean your induction cooker thoroughly before using for the first time ( Cleaning). Operating instructions Note: This appliance applies electromagnetic induction principles to heat. It is different from the traditional electrical heating method. The cooking utensil itself is used as the original generator of the cooking heat. A metal pan or pot must be used to generate the magnetic fields needed for heating up the food/soup in the container. If the metal Pan/pot is removed, the appliance will automatically shut down and stop heating. 1. Place the induction cooker on a flat, even and heat-resistant countertop surface. Make sure the air vent without any jam, without any …

Text truncated - open the document above for the full version.

Applicant letterhead AUTHORIZATION LETTER To: Federal Communications Commission 7435 Oaklanf Mills Road Columbia, MD 21046 Date: 17 December 2009 To whom it may concern: FCC ID: XZHELECTECH1 We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) to act on our behalf, as our agent, in the following matters related to the FCC approval of our product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by SGS within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Tony yang, safety engineer -------------------------------------- Name, position Applicant: Elec-Tech International Co., Ltd. Tel: 0756-3390075 Fax: 0756-3390522 Email: [email protected]

Confidentiality Letter (Date): 17 December 2009 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mils Road Columbia, Maryland 21046 Subject: Permanent Confidentiality request for FCC ID:XZHELECTECH1 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR47, the applicant requests permanent confidential treatment of the following information accompanying this application: Block Diagrams Schematics Operation Description Part List(if has) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Tony yang, safety engineer -------------------------------------- Name, position Applicant: Elec-Tech International Co., Ltd. Tel: 0756-3390075 Fax: 0756-3390522 Email: [email protected]

Elec-Tech International Co.,Ltd 广东德豪润达电气股份有限公司 No .1 Jinfeng Rd.,Tangjiawan Town, 珠海市香洲区唐家湾镇金凤路1号 Xiangzhou District,Zhuhai City, GuangDong,China Post code:519085 邮编：519085 Phone: 86-756-3390570 电话：86-756-3390570 Fax: 86-756-3390522 传真：86-756-3390522 E-mail: [email protected] 电子邮件：[email protected] Declaration We Elec-Tech International CO., LTD Declare that Model difference Induction cooker the model 257208;780-2402 is identical with model 250207 except the model number Elec-Tech International Co.,Ltd Signature: _____ Place and date: Zhu hai 2009/12/18

External photos

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technology Development District, Guangzhou, China 510663 Tel: +86 20 82155555 Fax: +86 20 82075059 Email: [email protected] FEDERAL COMMUNICATIONS COMMISSION Registration number: 282399 Report No.: GLEMO09120383701 Page: 1 of 13 FCC ID: XZHELECTECH1 Authorized Signature: Stephen Guo Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only Test Report Application No.: GLEMO091203837HS Applicant: Elec-Tech International Co., Ltd. FCC ID: XZHELECTECH1 Equipment Under Test (EUT): EUT Name: Induction cooker Item No.: 250207, 250208, 780-2402 ♣ ♣ Please refer to section 2 of this report which indicates which item was actually tested and which were electrically identical. Standards: FCC PART 18: 2008 Date of Receipt: 11 December 2009 Date of Test: 16 to 28 December 2009 Date of Issue: 04 January 2010 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GLEMO09120383701 Page: 2 of 13 FCC ID: XZHELECTECH1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Test Summary The customer requested EMC tests for an Induction cooker. Test Test Requirement Test Method Class / Severity Result Radiated Emission (9KHz to 30MHz) FCC PART 18: 2008 FCC OST/ MP-5:1986 18.305(b) PASS Conducted Emission (9KHz to 30MHz) FCC PART 18: 2008 FCC OST/ MP-5:1986 18.307(a) PASS ♣ Item No.: 250207, 250208, 780-2402 According to the declaration of the applicant, the electrical circuit design, layout, components used and internal wiring were identical for all models, with only difference being the model number. Therefore only one model 250207 was tested in this report. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GLEMO09120383701 Page: 3 of 13 FCC ID: XZHELECTECH1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)…

Text truncated - open the document above for the full version.

Radiated Emission Test Setup Cnducted Emissions Test Setup