XZZ-2700WNRSCT Wireless Mini WiFi Wireless-N-Router

3G Portable Router (With Rechargeable Li-Battery) User’s Manual Version: 1.0 (July, 2009) COPYRIGHT Copyright © 2009/2010 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed to Provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjuntion with any other antenna or transmitter. The equipment version marketed in US is restricted to usage of the channels 1-11 only. R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None. Important Health Information and Safety Precautions When using this product, the safety precautions below must be taken to avoid possible legal liabilities and damages. Retain and follow all product safety and operating instructions. Observe all warnings in the operating instructions on the product. To reduce the risk of bodily injury, electric shock, fire, and damage to the equipment, observe the following precautions. ELECTRICAL SAFETY This product is intended for use when supplied with power from the designated battery or power supply unit. Other usage may be dangerous and will invalidate any approval given to this product. SAFETY PRECAUTIONS FOR POWER SUPPLY UNIT  Use the correct external power source A product should be operated only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your authorized service provider or local power company. For a product that operates from battery power or other sources, refer to the operating instructions that are included with the product.  Handle battery packs carefully This product contains a Li-ion battery. There is a risk of fire and burns if the battery pack is handled improperly. Do not attempt to open or service the battery pack. Do not disassemble, crush, puncture, short external contacts or circuits, dispose of in fire or water, or expose a battery pack to temperatures higher than 60 ̊C (140 ̊F). WARNING: Danger of explosion if battery is incorrect…

Text truncated - open the document above for the full version.

CERTIFICATE Report No.: NEI-FCCE-1-0909C206C Issued Date: Apr. 08, 2010 RVC-1004003 Authorized under Declaration of Conformity according to 47 CFR, Part 2 and Part 15 of the FCC Rules. The product listed in follows was (were) tested in the Neutron EMC Laboratory to comply with the criteria limits Class B of conducted and radiated emissions of the Technical Standards FCC Part 15, Subpart B, established by the FCC, USA. Equipment SCT Wireless Mini WiFi Wireless-N-Router Model Name SCT-2700WNR Brand Name SCT Wireless Applicant SCT Wireless Address 1894 US Hwy 50 Ease Building 4 Suite 281 Carson City Nevada 89701 Measurement ANSI C 63.4 (2003) Method CISPR 22: 2005 +A1: 2005 ICES-003: 2004 The test data, data evaluation, and equipment configuration contained in our test report (Report No. NEI-FCCE-1- 0909C206C) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). The test data contained in the referenced test report relate only to the EUT sample and item(s) tested. Andy Chiu Authorized Signatory Neutron Engineering Inc. B1, No. 37, Lane 365, YangGuang St., NeiHu District 114, Taipei, Taiwan. TEL: +886-2-2657-3299 FAX: +886-2-2657-3331

Project No.: 0909C206C Page 2 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 1 0909C206C 0909C206 C Project No.: 0909C206C Page 3 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 2 0909C206C 0909C206 C Project No.: 0909C206C Page 4 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 3 0909C206C 0909C206 C Project No.: 0909C206C Page 18 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 17 0909C206C Project No.: 0909C206C Page 19 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 18

39x19mm

Project No.: 0909C206C Page 5 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 4 0909C206C 0909C206 C Project No.: 0909C206C Page 6 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 5 0909C206C Project No.: 0909C206C Page 7 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 6 0909C206C 0909C206 C Project No.: 0909C206C Page 8 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 7 0909C206C Project No.: 0909C206C Page 9 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 8 0909C206C Project No.: 0909C206C Page 10 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 9 0909C206C Project No.: 0909C206C Page 11 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 10 0909C206C Project No.: 0909C206C Page 12 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 11 0909C206C Project No.: 0909C206C Page 13 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 12 0909C206C Project No.: 0909C206C Page 14 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 13 0909C206C Project No.: 0909C206C Page 15 of 19 Neutron Engineering Inc. RVC-1004003 Photo No.: 14 0909C206C Project No.: 0909C206C Page 16 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 15 0909C206C Project No.: 0909C206C Page 17 of 19 Neutron Engineering Inc. RVC-1004003 0909C206C Photo No.: 16

Report No.: NEI-FCCP-1-0909C206C Page 117 of 124 Neutron Engineering Inc. RVC-1004003 9. RF EXPOSURE TEST 9.1 APPLIED PROCEDURES / LIMIT Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 9.1.1 MEASUREMENT INSTRUMENTS LIST Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Power Meter Anritsu ML2487A 6K00004714 Feb. 10, 2010 2 Power Meter Sensor Anritsu MA2491A 34138 Feb. 10, 2010 Remark: ” N/A” denotes No Model Name , Serial No. or No Calibration specified. 9.1.2 MPE CALCULATION METHOD E (V/m) ＝ d GP××30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP × ×× From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained Report No.: NEI-FCCP-1-0909C206C Page 118 of 124 Neutron Engineering Inc. RVC-1004003 9.1.3 DEVIATION FROM STANDARD No deviation. 9.1.4 TEST SETUP 9.1.5 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 4.1.6 Unless otherwise a special operating condition is specified in the follows during the testing. Report No.: NEI-FCCP-1-0909C206C Page 119 of 124 Neutron Engineering Inc. RVC-1004003 9.1.6 TEST RESULTS EUT： SCT Wireless Mini WiFi Wireless-N-Router Model Name ： SCT-2700WNR Temperature： 26°C Relative Humidity： 47% Test Voltage： AC 120V/60Hz Test Mode ： 802.11b Frequency (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) 2412 3.48 2.2284 19.8500 96.6051 0.042850 1 2437 3.48 2.2284 19.8600 96.8278 0.042949 1 2462 3.48 2.2284 19.9400 98.6279 0.043747 1 EUT： IEEE 802.11 bgn Wireless Router Model Name ： SCT-2700WNR Temperature： 13 °C Relative Humidity： 47% Test Voltage： AC 120V/60Hz Test Mode ： 802.11g Frequency (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) 2412 3.48 2.2284 23.9300 247.1724 0.109635 1 2437 3.48 2.2284 23.9200 246.6039 0.109383 1 2462 3.48 2.2284 23.8200 240.9905 0.106893 1 Report No.: NEI-FCCP-1-0909C206C Page 120 of 124 Neutron Engineering Inc. RVC-1004003 EUT： SCT Wireless Mini WiFi Wireless-N-Router Model Name ： SCT-2700WNR Temperature： 26°C Relative Humidity： 47% Test Voltage： AC 120V/60Hz Test Mode ： 802.11n HT20 Frequency (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) 2412 3.48 2.2284 23.6300 230.6747 0.102318 1 2437 3.48 2.2284 23.6600 232.2737 0.103027 1 2462 3.48 2.2284 23.6000 229.0868 0.101613 1 EUT： SCT Wireless Mini WiFi Wireless-N-Router Model Name ： SCT-2700WNR Temperature： 26°C Relative Humidity： 47% Test Voltage： AC 120V/60Hz Test Mode ： 802.11n HT40 Frequency (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) 2412 3.48 2.2284 22.6000 181.9701 0.080714 1 2437 3.48 2.2284 23.6500 231.7395 0.102790 1 2462 3.48 2.2284 23.7000 234.4229 0.103980 1 Remark： (1) The MIMO test requirement, MPE shall measure by using the total sum power of each transmitter chain.

Report No.: NEI-FCCP-1-0909C206C Page 1 of 124 Neutron Engineering Inc. RVC-1004003 Radio Test Report FCC ID: XZZ-2700WNR This report concerns (check one) : Original Grant Class I Change Issued Date : Apr. 08, 2010 Project No. : 0909C206C Equipment : SCT Wireless Mini WiFi Wireless-N-Router Model Name : SCT-2700WNR Applicant : SCT Wireless Address : 1894 US Hwy 50 Ease Building 4 Suite 281 Carson City Nevada 89701 Tested by: Neutron Engineering Inc. EMC Laboratory Date of Test: Nov. 13, 2009 ~ Nov. 24, 2009 Testing Engineer : (Rush Kao) Technical Manager : (Jeff Yang) Authorized Signatory : (Andy Chiu) Neutron Engineering Inc. B1, No. 37, Lane 365, YangGuang St., NeiHu District 114, Taipei, Taiwan. TEL: +886-2-2657-3299 FAX: +886-2-2657-3331 Report No.: NEI-FCCP-1-0909C206C Page 2 of 124 Neutron Engineering Inc. RVC-1004003 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCCP-1-0909C206C Page 3 of 124 Neutron Engineering Inc. RVC-1004003 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF RADIATED EMISSION TESTED 11 3.4 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION 13 4.1.2 MEASUREMENT INSTRUMENTS LIST 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 15 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 18 4.2.1 RADIATED EMISSION LIMITS 18 4.2.2 MEASUREMENT INSTRUMENTS LIST 19 4.2.3 TEST PROCEDURE 19 4.2.4 DEVIATION FROM TEST STANDARD 19 4.2.5 TEST SETUP 20 4.2.6 EUT OPERATING CONDITIONS 20 4.2.7 TEST RESULTS-BETWEEN 30MHZ - 1000MHZ 21 4.2.8 TEST RESULTS - ABOVE 1000MHZ 23 4.2.9 TEST RESULTS-RESTRICTED BANDS REQUIREMENTS 71 5 . BANDWITH TEST 87 5.1 APPLIED PROCEDURES / LIMIT 87 5.1.1 MEASUREMENT INSTRUMENTS LIST 87 5.1.2 TEST PROCEDURE 87 5.1.3 DEVIATION FROM STANDARD 87 5.1.4 TEST SETUP 87 5.1.5 EUT OPERATION CONDITIONS 87 5.1.6 TEST RESULTS 88 Report No.: NEI-FCCP-1-0909C206C Page 4 of 124 Neutron Engineering Inc. RVC-1004003 Table of Contents Page 6 . PEAK OUTPUT POWER TEST 96 6.1 APPLIED PROCEDURES / LIMIT 96 6.1.1 MEASUREMENT INSTRUMENTS LIST 96 6.1.2 TEST PROCEDURE 96 6.1.3 DEVIATION FROM STANDARD 96 6.1.4 TEST SETUP 96 6.1.5 EUT OPERATION CONDITIONS 96 6.1.6 TEST RESULTS 97 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 99 7.1 APPLIED PROCEDURES / LIMIT 99 7.1.1 MEASUREMENT INSTRUMENTS LIST 99 7.1.2 TEST PROCEDURE 99 7.1.3 DEVIATION FROM STANDARD 99 7.1.4 TEST SETUP 99 7.1.5 EUT OPERATION CONDITIONS 99 7.1.6 TEST RESULTS 100 8 . POWER SPECTRAL DENSITY TEST 108 8.1 APPLIED PROCEDURES / LIMIT 108 8.1.1 MEASUREMENT INSTRUMENTS LIST 108 8.1.2 TEST PROCEDURE 108 8.1.3 DEVIATION FROM STANDARD 108 8.1.4 TEST SETUP 108 8.1.5 EUT OPERATION CONDITIONS 108 8.1.6 TEST RESULTS 109 9 . RF EXPOSURE TEST 117 9.1 APPLIED PROCEDURES / LIMIT 117 9.1.1 MEASUREMENT INSTRUMENTS LIST 117 9.1.2 MPE CALCULATION METHOD 117 9.1.3 DEVIATION FROM STANDARD 118 9.1.4 TEST SETUP 118 9.1.5 EUT OPERATION CONDITIONS 118 9.1.6 TEST RESULTS 119 10 . EUT TEST PHOTO 121 11 . HISTORY 124 Report No.: NEI-FCCP-1-0909C206C Page 5 of 124 Neutron Engineering Inc. RVC-1004003 1. CERTIFICATION E q u i p m e n t : SCT Wireless Mini WiFi Wireless-N-Router Brand Name : SCT Wireless M o d e l N o . : SCT-2700WNR Applicant : SCT Wireless Date of Test : Nov. 13, 2009 ~ Nov. 24, 2009 Standards : FCC Part15, Subpart C / ANCI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-0909C206C) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: NEI-FCCP-1-0909C206C Page 6 of 124 Neutron Engineering Inc. RVC-1004003 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247 (c) Antenna conducted Spurious Emission PASS 15.247 (a)(2) 6dB Bandwidth PASS 15.247 (b) Peak Output Power PASS 15.247 (c) Radiated Spurious Emission PASS 15.247 (d) Power Spectral Density PASS…

Text truncated - open the document above for the full version.

Report No.: NEI-FCCP-1-0909C206C Page 121 of 124 Neutron Engineering Inc. RVC-1004003 10. EUT TEST PHOTO Conducted Measurement Photos Report No.: NEI-FCCP-1-0909C206C Page 122 of 124 Neutron Engineering Inc. RVC-1004003 Radiated Measurement Photos Report No.: NEI-FCCP-1-0909C206C Page 123 of 124 Neutron Engineering Inc. RVC-1004003 Radiated Measurement Photos