Y8ABTU280AM-FMFM STEREO RADIO WITH BLUETOOTH/CD/USB/MP3/SD CARD/AUX IN PLAYER

0 1 INSTRUCTION MANUAL PORTABLE CD/MP3/WMA DISC PLAYER FM STEREO RADIO & BLUETOOTH RECEPTION USB & SD CARD READER MODEL: BTU280AM-FM Please read and follow these instructions before using your unit. FCC Warnings This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. 2 3 LOCATION OF CONTROLS 1. HANDLE 2. FM TELESCOPIC ANTENNA 3. CD DOOR 4. VOLUME UP/DN CONTROL KNOB 5. POWER BUTTON 6. MODE/PROG/MEM BUTTON 7. 10+/M- BUTTON 8. LCD DISPLAY 9. STOP/M+ BUTTON 10. PLAY/PAUSE/PAIR BUTTON 11. FUNCTION BUTTON 12. CD DOOR OPEN AREA 13. TUN+/- & NEXT/PREVIOUS CONTROL KNOB 14. SPEAKERS 15. AUX IN JACK 16. BLUETOOTH INDICATOR 17. SD CARD SLOT 18. USB PORT 19. DC IN JACK 20. BATTERY COMPARTMENT POWER SUPPLIED BY THE AC/DC ADAPTER Plug the AC/DC adapter to the unit and the main power. POWER SUPPLIED BY BATTERIES The unit can be operated by batteries. Follow the below steps to install the batteries: 1. Remove the battery compartment cover gently. 2. Install 8 x 'C' size batteries (UM-2 or equivalent) taking care that the correct polarities are observed. 3. Replace the battery compartment cover. NOTE:  The AC/DC adapter must be removed for the battery operation.  To avoid damage which may result from leaking batteries, remove the batteries when they become weak or when the unit is not to be used for long period of time. PLAY THE RADIO 1. Press the POWER button to turn the unit on. 2. Press the FUNCTION button several times to enter the FM mode. 3. Rotate the TUN+/- control knob briefly to fine tune the radio station. Rotate and hold the TUN+/- control knob clockwise/counter-clockwise for a few seconds to auto search radio station forward or backward respectively (When an available station will be found, the unit will broadcast it immediately and the searching will be stopped). 4. The external FM TELESCOPIC ANTENNA is directional. When receiving FM broadcasts, fully extend the FM TELESCOPIC ANTENNA and position for the best reception. 5. Rotate the VOLUME UP/DN control knob to adjust the volume level. 6. Press the POWER button to turn off the unit. STORING YOUR FAVORITE RADIO STATION 1. During playback, press and hold the MODE/PROG/MEM button for storing the current station to the unit’s memory, the memory cell number flashes on the screen. 2. Press the STOP/M+ or 10+/M- button repeatedly to select the corresponding memory cell among P01-P10 for storing the station. 3. Confirm your selection by pressing the MODE/PROG/MEM button. 4. Repeat the above steps for storing other stations. 5. During radio playback, press the STOP/M+ or 10+/M- button repeatedly to recall the stored stations. 123 4 5 6 7 8 9 10 11 1213 14 15 171814 16 2019 4 5 HANDLE AND MAINTAIN A COMPACT DISC. Follow the instructions below to handle and maintain your disc in order that long time and trouble free performance can possibly be obtained:  Ensure not to caress the rain bow side of the disc; handle the disc by the edge.  Long time exposure to sunshine, high temperatures and humidity will damage the disc. Keep the storage area clean.  Avoid sticking labels on both sides of a disc. Writing with pointed articles on the disc should be strictly avoided.  Clean the disc wiping the centre and then working out to the edge with a dry & soft cloth or a disc brush. Avoid any cleansing lotion or chemical eradicator.  Store them in their cases when they are not to be used. LOAD A DISC 1. Power on the unit. 2. Press the FUNCTION button repeatedly to switch to the CD mode. 3. Open the CD door. 4. Insert a disc with the label side facing upward (if the disc is upside down, the display will indicate no disc on the screen). 5. Close the CD door by hand. NOTE: Never touch the laser lens inside the CD compartment. If it ever gets dirty, clean it with a CD cleaner disc. REMOVE A DISC 1. Make sure the disc is not playing. If it is, press the STOP/M+ button. 2. Open the CD door. 3. Gently remove the disc. 4. Close the CD door by hand. 5. Replace the disc in its protective storage box. P L AY A C D/MP3/WMA DISC 1. Power on the unit, press the FUNCTION button repeatedly to switch to the CD mode. 2. Load a CD/MP3/WMA disc into the CD compartment. Close the CD door, the disc will begin to spin. 3. Adjust the volume level to the desired volume level by using the VOLUME UP/DN control knob. 4. When the disc is successfully read, the total number of the disc shows on the display, the playback starts automatically. 5. Press the PLAY/PAUSE/PAIR button once to halt music playback, the elapsed time of the current track flashes to indicate t…

Text truncated - open the document above for the full version.

)
   


Page 1 of 3 External PHOTO: Model: BTU280AM-FM Page 2 of 3 Page 3 of 3

FM STEREO RADIO WITH BLUETOOTH/CD /MP3/USB/SD CARD/AUX IN PLAYER FREQUENCY RANGE: FM:87.5-108MHz POWER SUPPLY: INPUT DC 9V 1.5A POWER CONSUMPTION:13W MADE IN CHINA NGAILIK ELECTRONICS ENTERPRISES LIMITED This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference,and (2)this device must accept any interference received, including interference that may cause undesired operation. PBBT2702 FCC ID:Y8ABTU280AM-FM FM STEREO RADIO WITH BLUETOOTH/CD /MP3/USB/SD CARD/AUX IN PLAYER FREQUENCY RANGE: FM:87.5-108MHz POWER SUPPLY: INPUT DC 9V 1.5A POWER CONSUMPTION:13W MADE IN CHINA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference,and (2)this device must accept any interference received, including interference that may cause undesired operation. BTU280AM-FM FCC ID:Y8ABTU280AM-FM

Page 1 of 1 External PHOTO: Model: BTU280AM-FM Attach label here

Page 1 of 8 Internal PHOTO: Model: BTU280AM-FM PCB: Page 2 of 8 Page 3 of 8 Page 4 of 8 Page 5 of 8 Page 6 of 8 Page 7 of 8 Page 8 of 8

Operational Description Product Description This product integrated a Bluetooth chipset to support the Bluetooth function that allows users to use it as a speaker as the primary usage of this device. The brief introduction of the circuit 1. The Bluetooth signal is transmitted and received through the antenna system consists of the PCB antenna. 2. Power of the whole body is provided by 9VDC. 3. Aux in port is to connect audio source by line in cable to input audio signal. ON/OFF button is to turn on or turn off the speaker. 4. 9673B is MCU master control IC, it is use to button control, input Bluetooth, AUX, FM, CD, SD and USB switching, and output audio source to amplifier IC . 5. CD/TA8227 is to amplify audio signal provided by master control IC and motivate loudspeakers. 6.The chipset of BT is OVC3860,BT version is 2.1+EDR, modulation types are GFSK, (π/4)DQPSK, 8DPSK, The data rate is 1Mbps,2Mbps or 3Mbps. 7. The EUT have FM receive function Technical Description of FHSS The Bluetooth standard describes a frequency hopping spread spectrum system (FHSS). The frequency hopping sequence is governed by one unit known as the master in any group of units communicating together. The group is known as a piconet, and all units other than the master are known as slaves. The master determines the pseudo random hopping sequence internally and without reference to any external information, there is no co-ordination with any other Bluetooth or other FHSS systems to avoid simultaneous occupancy of hopping channels. Bluetooth uses re-transmission, interleaving and coding techniques to mitigate against lost transmissions when simultaneous occupancy of a channel cause loss of data. The pseudo random hopping sequence is initialized at the start of a new connection between master and slave to a random frequency ( hopping channel ), and the hopping sequence is generated such that an equal time is spent in each of 79 channels throughout the duration of the connection. The antenna supplied with PCB antenna with a max gain of 3 dBi. The antenna is an integral part of the device. The peak power of the transceiver is approximately 5 dBm, and the maximum EIRP is approximately 8 dBm.

ITL Page 1 of 86 Report No. 13033849 TEST REPORT Applicant: Ngai Lik Electronics Enterprises Limited Address of Applicant: Flat 29-32, 8/F., Block B, Focal Industrial Centre, 21 Man Lok Street, Hung Hom, Kowloon, Hong Kong. Manufacturer: Ngai Lik Electronics Enterprises Limited Address of Manufacturer: Flat 29-32, 8/F., Block B, Focal Industrial Centre, 21 Man Lok Street, Hung Hom, Kowloon, Hong Kong. Product name: FM STEREO RADIO WITH BLUETOOTH/CD/USB/MP3/SD CARD/AUX IN PLAYER Model: For main: BTU280AM-FM; PBBT2702 For AC Adapter: APX915A Rating(s): For main: Input DC 9V, 13W; For AC Adapter: Input 100-240V~, 50/60Hz, 0.5A max. Output: DC 9V, 1.5A Trademark: AXESS for PBBT2702 Standards: FCC Part 15.247 :2011 FCC ID: Y8ABTU280AM-FM Data of Receipt: 2013-03-08 Date of Test: 2013-03-08~2013-04-03 Date of Issue: 2013-04-11 Test Result Pass* * In the configuration tested, the test item complied with the standards specified above. Authorized for issue by: Test by: Reviewed by: Apr.11.2013 Jumy Qiu Apr.11.2013 Pauler Li Project Engineer Project Manager Date Name/Position Signature Date Name/Position Signature ITL Page 2 of 86 Report No. 13033849 Possible test case verdicts: test case does not apply to the test object .. : N/A test object does meet the requirement ........ : P (Pass) test object does not meet the requirement .. : F (Fail) Testing Laboratory information: Testing Laboratory Name .......... : I-Test Laboratory Address : 1-2 floor, South Block, Building A2 , No 3 Keyan Lu, Science City, Guangzhou, Guangdong Province, P.R. China Testing location : Same as above Tel : 0086-20-32209330 Fax : 0086-20-62824387 E-mail : [email protected] General remarks: The test results presented in this report relate only to the object tested. The results contained in this report reflect the results for this particular model and serial number. It is the responsibility of the manufacturer to ensure that all production models meet the intent of the requirements detailed within this report. This report would be invalid test report without all the signatures of testing technician and approver. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. General product information: / ITL Page 3 of 86 Report No. 13033849 1 Test Summary Test Test Requirement Test method Result Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15. 203 FCC PART 15 C section 15.247 (c) and Section 15. 203 PASS Occupied Bandwidth ( -20dB) FCC PART 15 C section 15.247 (a)(1); ANSI C63.10: Clause 6.9 & DA 00-705 PASS Carri er Fr equencies Separated FCC PART 15 C section 15.247(a)(1); DA 00-705 PASS Hopping Channel Number FCC PART 15 C section 15.247(a)(1)(i ii) DA 00-705 PASS Dwell Time FCC PART 15 C section 15.247(a)(1)(i ii); DA 00-705 PASS Maximum Peak Output Power FCC PART 15 C section 15.247(b)(1); ANSI C63.10: Clause 6.10 & DA 00-705 PASS Conducted Spurious Emission (30 MHz to 25 GHz) FCC PART 15 C section 15.247(d); ANSI C63.10: Clause 6.7 & DA 00-705 PASS Radiated Spurious Emission (9 kHz to 25 GHz) FCC PART 15 C section 15.247(d); ANSI C63.10: Clause 6.4, 6.5 and 6.6 & DA 00-705 PASS Band Edges Measurement FCC PART 15 C section 15.247 (d) &15.205 ANSI C63.10: Clause 6.9 & DA 00-705 PASS Conducted Emissions at Mains Terminals FCC PART 15 C section 15.207; ANSI C63.10: Clause 6.2 & DA 00-705 PASS Remark: N/A: not applicable. Refer to the relative section for the details. EUT: In this whole report EUT means Equipment Under Test. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radio Fr equency. ANSI C63.10: the detail version is ANSI C63.10:2009 in the whole report. DA 00-705: “Filing and Measurement Guidelines for Frequency Hopping Spread Spectrum Systems” ITL Page 4 of 86 Report No. 13033849 2 Contents Page TEST REPORT ....................................................................................................................................................................... 1 1 TEST SUMMARY ......................................................................................................................................................... 3 2 CONTENTS ................................................................................................................................................................... 4 3 GENERAL INFORMATION ........................................................................................................................................ 5 3.1 CLIENT INFORMATION ............................................................................................................................................ 5 3.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 5 3.3 DETAILS OF E.U.T. ................................................................................................................................................ 5 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................ 5 3.5 TEST LOCATION ..................................................................................................................................................... 6 3.6 DEVIATION FROM STANDARDS .............................................................................................................................. 6 3.7 ABNORMALITIES FROM STANDARD CONDITIONS.................................................................................................. 6 3.8 OTHER INFORMATION REQUESTED BY THE CUSTOMER ....................................................................................... 6 3.9 TEST FACILITY ..................................................................................................................................…

Text truncated - open the document above for the full version.