Y9E-IAD18001Smart Signboard

IAD18000/18001 10.1 HD Smart Signboard IAdea Corporation 綠創科技 綠創科技綠創科技 綠創科技 18001 Hardware User Manual 10.1 HD Smart Signboard IAdea Corporation User Manual Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.



Consult the dealer or an experienced radio/TV technician for help. Adaptor with ferrite must be used with this equipment to ensure compliance with the Class B FCC limits. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. “FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the FCC & CE’s RF exposure guidelines, place the product at least 20cm from nearby persons.” The power consumption of the product in networked standby is 5.927W which all wired network ports are connected and all wireless network ports are activated. Adapter manufacturer: Asia Power Devices Inc. Model No.: WB-18D12R Input: 100-240V~50-60Hz0.5A Max. Output: i Contents IAD18000/18001 Hardware User Manual 0 1. Introduction 1 1.1. Package contents 1 1.2. Physical view and features 1 1.3. Installation 3 1.4. System setup 4 1.5. Connect device to network 5 1.6. Content Management 5 2. Technical Data 6 2.1. Specifications 6 1 1. Introduction This document describes the hardware 1.1. Package contents 1.2. Physical view and features Front View Main Unit hardware specification of the IAD18001. and features Power adapter with Power and MicroSD Table Stand Table Stand (IAD18001 only) 2 Rear View 3 1.3. Installation Securing the power and network cable 1 Insert power plug 2 Fasten bracket onto the socket Securing Micro SD card 1 Insert SD card bracket 2 Fasten SD card bracket Installing the table stand 1 Simply screw the supplied table stand into stand screw hole Support landscape and portrait setup 4 Mounting IAD18001 is MIS-D75 compatible, the recommended screw is M4 x 4.5~5mm (excl. bracket thickness) Mounting Option 1: [VESA mount] Supporting VESA standard: VESA MIS-D75 (75*75mm) Supporting screw: M4*4mm (exclude the mounting plate thickness) Mounting Option 2: [Using back cover] (power / SD card brackets MUST NOT installed while mount on back cover) 1 Release the back cover screw to release back cover 2 Install back cover : thread head height must not exceed 3mm 3 Route power and network cable from bottom as shown in photo 4 Plug power and network cable to signboard , and then install signboard with back cover carefully 1.4. System setup 1 INSTALL the AC power adapter → You should see the player boot up screen as shown in right 2 WAIT while player boots up → once you see “Basic settings” on screen, the unit is ready for content update or menu configuration 3 PLUG IN a USB mouse to the unit’s USB port or configure by touch screen(IAD18001 only) 4 Enter the corresponding configuration option by moving the mouse cursor over the configuration and click on the option to enter (or tap on the configuration option for IAD18001) → find and set the correct time/date AND time zone. IMPORTANT: time zone must be set correctly in the menu or via management software for scheduled playback → (OPTIONAL) Set a Password in the menus to prevent unauthorized changes. IMPORTANT: Password will be asked while enter the setup menu during playback 5 Click Set content button to configure your signage appliance to the content service if needed → For advanced player configuration, such as static IP, display resolution, and firmware update, visit www.digisignage.com for more information 5 1.5. Connect device to network 1 Click the Wireless LAN setting to launch the wireless configuration UI. 2 Click the ON/OFF button as indicated below to turn ON Wireless interface (network). 3 The player will scan for wireless signals nearby and available access points will be listed. 4 Click on the network ID to connect. If the network requires authentication, you will be asked to provide a password. 1.6. Content Management Please consult the software documentation for information specific to your management solution. 6 2. Technical Data 2.1. Specifications IAD18000/18001 Display 10.1” IPS panel 10 points multi-touch (IAD18001 only ) Programming LED bar x 2 (IAD18001 only ) 300 nits maximum brightness 1280x800 panel resolution Viewing angle (H/V): 178/178 Built-in speaker 2W x 2 Video format support H.264 (up to 1080p,10Mbps) VC-1 (up to 1080p,10Mbps) MPEG-4 ASP (up to 1080p,10Mbps) MPEG-2 (up to 1080p,10Mbps) POPAI Screen Media Standards : S6 to S12, E4,E7,E8 Image…

Text truncated - open the document above for the full version.

External Photos

          !"!#!$%& '(#$%&                 !" #       !        "#$ %    & #'$  %   &      %     ()*+*,"    -  -      $%  #"#& '                 !" #       !        "#$ %    & #'$  %   &      %     ()*+*,"    -  -      $%  #"#& '                 !" #       !        "#$ %    & #'$  %   &      %     ()*+*,"    -  -    $%  #"#& '  !"#$% IAD-18001IAD-18000 Label Artwork

Internal Photos IAD18001 IAD18000

INTERTEK TESTING SERVICES FCC ID: Y9E-IAD18001 R F Exposure report The Equipment Under Test (EUT) is a Smart Signboard with WiFi function o p erating at 2412-2462MHz for 802.11b/g/n-HT20, 11 channels with 5MHz channel spacing and 2422-2452MHz for 802.11n-HT40, 9 channels with 5MHz channel spacing. The EUT was powered by AC/DC adaptor through AC120V/60Hz or PoE. For more detailed features description, please refer to the user’s manual. Modulation Type: BPSK, QPSK, 16QAM, 64QAM for OFDM. CCK, DQPSK, DBPSK for DSSS. Antenna Type: Integral antenna Antenna Gain: 2.2dBi The nominal conducted output power specified: 21dBm (Tolerance: +/-3dB) The maximum conducted output power for the EUT is 22.62dBm in the frequency 2.462GHz 802.11g mode which is within the production variation. The minimum conducted output power for the EUT is 19.49dBm in the frequency 2.412GHz 802.11b mode which is within the production variation. According to FCC Part 2.1091, this unlicensed transmitting devices is categorically excluded from routine environmental evaluation for RF exposure prior to equipment authorization or use. For Maximum Permissible Exposure (MPE) evaluation of the product, the maximum power density at 20 cm from this transmitter shall be less than the General Population / Uncontrolled MPE limit in FCC Part 1.1310. The maximum EIRP= 21+3+2.2=26.2dBm=416.9mW The source-based time averaged maximum radiated power = 416.9 mW x Duty Cycle = 416.9mW From above data, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET 65 as follow: = PG/4πR^2 = E IRP/4πR^2 = 416.9/ 4πR^2 = 0 .08 mW/cm^2 INTERTEK TESTING SERVICES FCC ID: Y9E-IAD18001 T he MPE limit is 1.0 mW/cm^2 for general population and uncontrolled exposure in the WiFi frequency range according to FCC Part 1.1310. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structure and body of the user or nearby persons. Transmitter Duty Cycle Calculation The EUT transmit continuously during the test, the duty cycle is 100%. The following RF exposure statement or similar sentence is proposed to be included in the user manual: “FCC RF Radiation Exposure Statement Caution: This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons.”

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_Tx_c Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com IAdea Corporation Application For Certification FCC ID: Y9E-IAD18001 Smart Signboard Model: IAD18001 Additional Model: IAD18000 2.4GHz WiFi Transceiver Report No.: 151103004SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-14] Prepared and Checked by: Approved by: Sign on file Harry Wu Engineer Andy Yan Senior Project Engineer Date: November 30, 2015 INTERTEK TESTING SERVICE TRF no.: FCC 15C_TX_c FCC ID: Y9E-IAD18001 Report No.: 151103004SZN-001 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: Summary of Tests EXHIBIT 2: General Description EXHIBIT 3: System Test Configuration EXHIBIT 4: Measurement Results EXHIBIT 5: Equipment Photographs EXHIBIT 6: Product Labeling EXHIBIT 7: Technical Specifications EXHIBIT 8: Instruction Manual EXHIBIT 9: Confidentiality Request EXHIBIT 10: Miscellaneous Information EXHIBIT 11: Test Equipment List INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_c FCC ID: Y9E-IAD18001 Report No.: 151103004SZN-001 ii MEASUREMENT/TECHNICAL REPORT Smart Signboard Model: IAD18001 FCC ID: Y9E-IAD18001 This report concerns (check one) Original Grant X Class I Change Equipment Type: DTS - Part 15 Digital Transmission Systems (WiFi transmitter portion) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-14] Edition] provision. Report prepared by: Harry Wu Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0716 Fax: (86 755) 8614 0716 INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_c FCC ID: Y9E-IAD18001 Report No.: 151103004SZN-001 iii Table of Contents 1.0 Summary of Test results ............................................................................................................................. 2 2.0 General Description ...................................................................................................................................... 4 2.1 Product Description ..................................................................................................................................... 4 2.2 Related Submittal(s) Grants ....................................................................................................................... 5 2.3 Test Methodology ........................................................................................................................................ 5 2.4 Test Facility .................................................................................................................................................. 5 3.0 System Test Configuration ......................................................................................................................... 7 3.1 Justification .................................................................................................................................................. 7 3.2 EUT Exercising Software............................................................................................................................ 7 3.3 Special Accessories .................................................................................................................................... 7 3.4 Measurement Uncertainty .......................................................................................................................... 8 3.5 Equipment Modification .............................................................................................................................. 8 3.6 Support Equipment List and Description ................................................................................................ 8 4.0 Measurement Results................................................................................................................................. 10 4.1 Maximum Conducted Output Power at Antenna Terminals ..................................................................... 10 4.2 Minimum 6 dB RF Bandwidth ........................................................................................................…

Text truncated - open the document above for the full version.