YQKCEIIPT-230Wetness Sensor

T-230 Wetness Sensor A. Specifications: Battery LR43 Power consumption Max 34mA Stand-by current 1.5uA Voltage 2.2VDC – 3VDC Communication 433.92MHz, FSK, 57.6K bit rate Sensitivity -104dBm Transmit power <10 dBm Address length 16 bit Operating temperature range 0 – 60 °C B. Functions: - Clip-on notification - 64 levels of wetness - Battery low notification C. Instructions of use: 1. Clipping After clipped-on, the pins in wetness sensor will be attached on the two parallel sensing conductive lines. If the contact is good, the sensor will sound a long “beep”. If the contact is poor, the sensor will sound 3 short “beeps”. When the sensor is detached, a “beep” will be sounded. 2. Matching To enter the code-matching mode, place the sensor on top of R-138a as the figure. 3. Battery low notification When the voltage falls to 2.2V, the sensor will sound “beep-beep”, “beep-beep”, “beep-beep” when it is clipped on. Replace the battery immediately. The sensor stops working when the voltage falls to 2.2V. 4. Wetness data transmission and update The sensor takes 30-60 seconds to proceed from “moist” to “damp”. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.105: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Statement according to FCC part 15.21: FCC Caution: Any changes or modifications not expressly approved by the party responsible could void the user’s authority to operate this device.

T-230 Wetness Sensor A. Specifications: Battery LR43 Power consumption Max 34mA Stand-by current 1.5uA Voltage 2.2VDC – 3VDC Communication 433.92MHz, FSK, 57.6K bit rate Sensitivity -104dBm Transmit power <10 dBm Address length 16 bit Operating temperature range 0 – 60 °C B. Functions: - Clip-on notification - 64 levels of wetness - Battery low notification C. Instructions of use: 1. Clipping After clipped-on, the pins in wetness sensor will be attached on the two parallel sensing conductive lines. If the contact is good, the sensor will sound a long “beep”. If the contact is poor, the sensor will sound 3 short “beeps”. When the sensor is detached, a “beep” will be sounded. 2. Matching To enter the code-matching mode, place the sensor on top of R-138a as the figure. 3. Battery low notification When the voltage falls to 2.2V, the sensor will sound “beep-beep”, “beep-beep”, “beep-beep” when it is clipped on. Replace the battery immediately. The sensor stops working when the voltage falls to 2.2V. 4. Wetness data transmission and update The sensor takes 30-60 seconds to proceed from “moist” to “damp”. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.105: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Statement according to FCC part 15.21: FCC Caution: Any changes or modifications not expressly approved by the party responsible could void the user’s authority to operate this device.

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT PHOTOGRAPH OF THE PRODUCT LEFT VIEW OF THE PRODUCT RIGHT VIEW OF THE PRODUCT PHOTOGRAPH OF THE PRODUCT TOP VIEW OF THE PRODUCT BTTOM VIEW OF THE PRODUCT

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT PHOTOGRAPH OF THE PRODUCT LEFT VIEW OF THE PRODUCT RIGHT VIEW OF THE PRODUCT PHOTOGRAPH OF THE PRODUCT TOP VIEW OF THE PRODUCT BTTOM VIEW OF THE PRODUCT

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT BOTTOM VIEW

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT BOTTOM VIEW

STC Test Report Date : 2012-09-21 Page 1 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre Ltd. For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of Homepage. Applicant (CKT001): CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Manufacturer: CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Description of Sample(s): Submitted sample(s) said to be Product: Wetness Sensor Brand Name: Carease Model Number: T-230 FCC ID: YQKCEIIPT-230 Date Sample(s) Received: 2012-08-15 Date Tested: 2012-08-29 to 2012-09-10 Investigation Requested: Perform ElectroMagnetic Interference measurement in accordance with FCC 47CFR [Codes of Federal Regulations] Part 15: 2011 and ANSI C63.4:2009 for FCC Certification. Conclusion(s): The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remark(s): --- Dr. LEE Kam Chuen Authorized Signatory ElectroMagnetic Compatibility Department For and on behalf of The Hong Kong Standards and Testing Centre Ltd. STC Test Report Date : 2012-09-21 Page 2 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage CONTENT: Cover Page 1 of 22 Content Page 2-3 of 22 1.0 General Details 1.1 Test Laboratory Page 4 of 22 1.2 Applicant Details Page 4 of 22 Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 22 Description of EUT operation 1.4 Date of Order Page 5 of 22 1.5 Submitted Sample(s) Page 5 of 22 1.6 Test Duration Page 5 of 22 1.7 Country of Origin Page 5 of 22 2.0 Technical Details 2.1 Investigations Requested Page 6 of 22 2.2 Test Standards and Results Summary Page 6 of 22 3.0 Test Results 3.1 Emission Page 7-12 of 22 3.2 Bandwidth Measurement Page 13-14 of 22 STC Test Report Date : 2012-09-21 Page 3 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage Appendix A List of Measurement Equipment Page 15 of 22 Appendix B Duty Cycle Correction During 100 msec Page 16-19 of 22 Appendix C Periodic Operation Page 20 of 22 Appendix D Photographs Page 21-22 of 22 STC Test Report Date : 2012-09-21 Page 4 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong Telephone: 852 2666 1888 Fax: 852 2664 4353 1.2 Applicant Details Applicant CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Manufacturer CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. STC Test Report Date : 2012-09-21 Page 5 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage 1.3 Equipment Under Test [EUT] Description of Sample Submitted sample(s) said to be Product: Wetness Sensor Manufacturer: CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Brand Name: Carease Model Number: T-230 Rating: 3Vd.c. (“LR43” size battery x 2) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a CKICOM TECHNOLOGY LTD., Wetness Sensor. The EUT is a 433MHz transceiver, a RF signal will be transmitted when the wetness sensor of EUT is triggered, the RF transmission will stop when the sensor resumed to un-triggered status or is disable by another transmitter. 1.4 Date of Order 2012-08-15 1.5 Submitted Sample(s): 1 Sample 1.6 Test Duration 2012-08-29 to 2012-09-10 1.7 Country of Origin Hong Kong STC Test Report Date : 2012-09-21 Page 6 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testin…

Text truncated - open the document above for the full version.

STC Test Report Date : 2012-09-21 Page 1 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre Ltd. For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of Homepage. Applicant (CKT001): CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Manufacturer: CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Description of Sample(s): Submitted sample(s) said to be Product: Wetness Sensor Brand Name: Carease Model Number: T-230 FCC ID: YQKCEIIPT-230 Date Sample(s) Received: 2012-08-15 Date Tested: 2012-08-29 to 2012-09-10 Investigation Requested: Perform ElectroMagnetic Interference measurement in accordance with FCC 47CFR [Codes of Federal Regulations] Part 15: 2011 and ANSI C63.4:2009 for FCC Certification. Conclusion(s): The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remark(s): --- Dr. LEE Kam Chuen Authorized Signatory ElectroMagnetic Compatibility Department For and on behalf of The Hong Kong Standards and Testing Centre Ltd. STC Test Report Date : 2012-09-21 Page 2 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage CONTENT: Cover Page 1 of 22 Content Page 2-3 of 22 1.0 General Details 1.1 Test Laboratory Page 4 of 22 1.2 Applicant Details Page 4 of 22 Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 22 Description of EUT operation 1.4 Date of Order Page 5 of 22 1.5 Submitted Sample(s) Page 5 of 22 1.6 Test Duration Page 5 of 22 1.7 Country of Origin Page 5 of 22 2.0 Technical Details 2.1 Investigations Requested Page 6 of 22 2.2 Test Standards and Results Summary Page 6 of 22 3.0 Test Results 3.1 Emission Page 7-12 of 22 3.2 Bandwidth Measurement Page 13-14 of 22 STC Test Report Date : 2012-09-21 Page 3 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage Appendix A List of Measurement Equipment Page 15 of 22 Appendix B Duty Cycle Correction During 100 msec Page 16-19 of 22 Appendix C Periodic Operation Page 20 of 22 Appendix D Photographs Page 21-22 of 22 STC Test Report Date : 2012-09-21 Page 4 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong Telephone: 852 2666 1888 Fax: 852 2664 4353 1.2 Applicant Details Applicant CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Manufacturer CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. STC Test Report Date : 2012-09-21 Page 5 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testing Centre Ltd. For Conditions of Issuance of this test report, please refer to the overleaf or Homepage 1.3 Equipment Under Test [EUT] Description of Sample Submitted sample(s) said to be Product: Wetness Sensor Manufacturer: CKICOM TECHNOLOGY LTD. Flat F 4/F Universal Ind. Ctr. 19-21 Shan Mei St, Fotan, Hong Kong. Brand Name: Carease Model Number: T-230 Rating: 3Vd.c. (“LR43” size battery x 2) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a CKICOM TECHNOLOGY LTD., Wetness Sensor. The EUT is a 433MHz transceiver, a RF signal will be transmitted when the wetness sensor of EUT is triggered, the RF transmission will stop when the sensor resumed to un-triggered status or is disable by another transmitter. 1.4 Date of Order 2012-08-15 1.5 Submitted Sample(s): 1 Sample 1.6 Test Duration 2012-08-29 to 2012-09-10 1.7 Country of Origin Hong Kong STC Test Report Date : 2012-09-21 Page 6 of 22 No. : HM167830 T h e H o n g K o n g S t a n d a r d s a n d T e s t i n g C e n t r e L t d . 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] This report shall not be reproduced unless with prior written approval from The Hong Kong Standards and Testin…

Text truncated - open the document above for the full version.

PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP

PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP