YTT-FLX100Vengeance High Definition E-game Call

Model # FLX100 602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Flextone” is a registered trademark of Wildgame Innovations, LLC. “VENGEANCE” & “Sport Responsible” are TM trademarks of WGI Innovations, LTD. User’s Manual HD E-GAME CALL INCLUDED PARTS 1) Vengeance electronic game call – (1) 2) Product Information Guide – (1) PAGE 1 Model # FLX100 602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Flextone” is a registered trademark of Wildgame Innovations, LLC. “VENGEANCE” & “Sport Responsible” are TM trademarks of WGI Innovations, LTD. User’s Manual HD E-GAME CALL INSTALLING BATTERIES PAGE 2 3 To close put battery chamber back inside cavity, put the cover over and press in. Press the door snap after battery door installment to ensure door snap engagement. 1 Turn the call on it’s side and place thumb on the cover while pressing down and sliding open. 2 Next, pull out the battery chamber, confirm that the positive (+) and negative (–) terminals are oriented correctly as described on the label at the entrance and insert the AA batteries. PAGE 3 3 To close, place the cover over and press down. INSTALLING BATTERIES IN REMOTE 2negative (–) terminals are oriented correctly as described on the label at the entrance and insert the batteries. 1 To install the AAA batteries for the remote, push down on the button and slide open the cover .Press the door snap after batter y door installment to ensure door snap engagement. VOL + VOL - TURNING UNIT ON Press and hold the power button until LCD is illuminated and then release. Unit is now on. Note: THE LCD will enter sleep mode in approximately 40 seconds of inactivity PAGE 4 CHOOSING CALL CATEGORY 1 First, select desired call category by pressing and releasing the middle button. Category name should now be blinking. 2 Next, press either the left or right button to view the categories. VOL + VOL - 3 When desired category is identified, press and release middle button. Select ear ategory. . . Bird VOL + VOL - Bobca Select Category. . . Select Category. . . CHOOSING INDIVIDUAL CALLS TO USE CALL Blue Jay Bird PAGE 5 VOL + VOL - VOL + VOL - Blue Jay Bird After the category has been chosen, scroll left or right to view individual calls within the category. Once the desired call is identified, press the play button to activate the speaker. This will activate the audible call. To maximize the effectiveness of the Vengeance, point the call in the direction you want the call to go to. Note: Call will loop repeatedly until call is deactivated. DO NOT PRESS ENTER BUTTON TO ACTIVATE CALL. PAGE 6 To adjust volume, press the volume up or down buttons. VOLUME CONTROL TURN UNIT OFF VOL + VOL - VOL + VOL - Press and hold the power button until LCD is illuminated and then release. Unit is now off. Note: THE LCD will enter sleep mode in approximately 40 seconds of inactivity. The unit will off if no any sound output for 15 minutes. To adjust sound from left speaker to right speaker, press top left button. VOL + VOL - Blue Jay Bird Blue Jay Bird PAGE 7 VOL + VOL - Press and hold the power button until LCD is illuminated and then release. Unit is now on. TURNING REMOTE ON CHOOSING CALL CATEGORY 1 First, select desired call category by pressing and releasing the middle button. Category name should now be blinking. 2 Next, press either the left or right button to view the categories. When desired category is identified, press and release middle button. select category... Bird Note: THE LCD will enter sleep mode in approximately 40 seconds of inactivity. Blue Jay Bird VOL + VOL - Bobcat Yo Bobcat VOL + VOL - CHOOSING INDIVIDUAL CALLS After the category has been chosen, scroll left or right to view individual calls within the category. TO USE CALL Once the desired call is identified, press the play button to activate the speaker. This will activate the audible call. Note: Call will loop repeatedly until call is deactivated. DO NOT PRESS ENTER BUTTON TO ACTIVATE CALL. To adjust volume, press the volume up or down buttons. VOLUME CONTROL Female Bobcat VOL + VOL - VOL + VOL - VOL + VOL - VOL + VOL - To adjust sound from left speaker to right speaker, press top right button. PAGE 8 PAGE 9 AUDIO IN/AUDIO OUT Plug in external audio device with 3.5 mm cable to either the Audio Input or the Audio Out depending on the device and required results. Both Audio In/Audio Out Functions can be controlled from the main unit and the remote. Audio In Audio Out Audio In Audio Out REMOTE DETACHMENT To detach the remote place thumb on the button while pressing down and sliding out. PAGE 10 To attach the remote hold with buttons facing down and slide in until it clicks. DISCLAIMERS WGI Innovations, LTD. is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY You must register your product warranty online at www.wildgameinnovations.com. Follow the on screen directions to complete the process. WGI Innovations, LTD. will replace any product that may encounter material or workmanship defects free of charge for ONE (1) YEAR after the date of purchase and thereafter the cost will vary per incident. This warranty DOES NOT COVER damage, expense or injury caused by unauthorized repairs, animal damage, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss. When returning product for service you MUST obtain a Return Merchandise Authorization (RMA) number from WGI Innovations, LTD. Please include name, UPS address (no P.O. Box), telephone number, RMA number and a complete description of the problem on all enclosed correspondence. When possible, pack product carefully in original carton. Customers are responsible for any shipping cost to WGI Innovations™. WGI Innovations™ will pay shipping cost of replacement product to the customer. We are not responsible for damage incurred in returning items for repair. CUSTOMER SERVICE WGI…

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details Test model No.: FLX100 1

1 Photographs - EUT Constructional Details Test model No.: FLX100

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200081803 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1502000818CR Applicant: WGI Innovations, Ltd. Manufacturer: Jianhui Plastic & Electronic Industry (Shenzhen) Co. Ltd. Factory: WGI Innovations, Ltd. Product Name: Vengeance High Definition E-game Call Model No.(EUT): FLX100 Trade Mark: Flextone FCC ID: YTT-FLX100 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-03-13 Date of Test: 2015-03-16 to 2015-04-01 Date of Issue: 2015-04-10 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200081803 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-04-10 Original Authorized for issue by: Tested By 2015-04-01 (Owen Zhou) /Project Engineer Date Prepared By 2015-04-07 (Sade Luo) /Clerk Date Checked By 2015-04-07 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200081803 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE .....................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200081802 Page: 1 of 24 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. ′′This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.′′ 1 Cover Page FCC REPORT Application No.: SZEM1502000818CR Applicant: WGI Innovations, Ltd. Manufacturer: Jianhui Plastic & Electronic Industry (Shenzhen) Co. Ltd. Factory: WGI Innovations, Ltd. Product Name: Vengeance High Definition E-game Call Model No.(EUT): FLX100 Trade Mark: Flextone FCC ID: YTT-FLX100 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-03-13 Date of Test: 2015-03-16 to 2015-04-01 Date of Issue: 2015-04-07 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200081802 Page: 2 of 24 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-04-07 Original Authorized for issue by: Tested By 2015-04-01 (Owen Zhou) /Project Engineer Date Prepared By 2015-04-07 (Sade Luo) /Clerk Date Checked By 2015-04-07 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200081802 Page: 3 of 24 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203 ANSI C63.10(2009)…

Text truncated - open the document above for the full version.

1 Photographs - Test setup (Test Model No.: FLX100) 1.1 Radiated Emission