Z2HPBBK80Lyrix Powerball

Report No.: BL-SZ1520008-601 102 ANNEX C EUT PHOTOS C.1 Appearance of the EUT THE FRONT OF EUT THE BACK OF EUT Report No.: BL-SZ1520008-601 103 THE LEFT OF EUT THE RIGHT OF EUT Report No.: BL-SZ1520008-601 104 THE UP OF EUT THE DOWN OF EUT Report No.: BL-SZ1520008-601 105 THE USB CABLE

Label Label Location FCC ID: Z2HPBBK80 Model No. 08945 INPUT: 5V 500mA Made in China www.digitaltreasure.com

Report No.: BL-SZ1520008-601 106 C.2 Inside of the EUT EUT UNCOVER VIEW 1 MAIN BOARD TOP VIEW 1 Report No.: BL-SZ1520008-601 107 MAIN BOARD TOP VIEW 2 MAIN BOARD BACK VIEW 2 PCB Antenna BT Chip Report No.: BL-SZ1520008-601 108 MAIN BOARD TOP VIEW 3 MAIN BOARD BACK VIEW 3 Report No.: BL-SZ1520008-601 109 BATTERY --END OF REPORT--

RF Exposure Evaluation for Z2HPBBK80 Refer user manual this device is a Bluetooth Speaker and this device was designed used in portable devices the minimum distance between human’s body is 5mm. Based on the 47CFR 2.1093, this device belongs to portable device. The definition of the category as following: Portable Derives: CFR Title 47 §2.1093(b) (b) For purposes of this section, a portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. FCC KDB 447498 D01 General RF Exposure Guidance v05r02 Limit Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [ (max.power of channel,including tune −up tolerance,mW) (min.test separation distanc e,mm) ] · [ � f (GHz) ] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR Where • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. FCC exclusion condition= [ (0.6,mW) (5,mm) ] · [ � 2. 48 (GHz) ] = 0.19 ＜ 3.0 RF Exposure Evaluation Result: PA S S

Report No.: BL-SZ1520008-601 2 Revision History Version Issue Date Revisions Rev. 01 Feb. 13, 2015 Initial Issue TABLE OF CONTENTS 1 ADMINISTRATIVE DATA (GENERAL INFORMATION) ........................................................................ 5 1.1 Identification of the Testing Laboratory ............................................................................................ 5 1.2 Identification of the Responsible Testing Location ........................................................................... 5 1.3 Announce ........................................................................................................................................ 5 2 PRODUCT INFORMATION ................................................................................................................... 6 2.1 Applicant ......................................................................................................................................... 6 2.2 Manufacturer ................................................................................................................................... 6 2.3 General Description for Equipment under Test (EUT) ..................................................................... 6 2.4 Technical Information ...................................................................................................................... 6 2.5 Ancillary Equipment ......................................................................................................................... 7 3 SUMMARY OF TEST RESULTS ........................................................................................................... 8 3.1 Test Standards ................................................................................................................................ 8 3.2 Verdict ............................................................................................................................................. 8 4 GENERAL TEST CONFIGURATIONS .................................................................................................. 9 4.1 Test Environments .......................................................................................................................... 9 4.2 Test Equipment List ......................................................................................................................... 9 4.3 Test Configurations ....................................................................................................................... 10 4.4 Description of Test Setup .............................................................................................................. 10 4.4.1 For Antenna Port Test ............................................................................................................ 10 4.4.2 For AC Power Supply Port Test .............................................................................................. 11 4.4.3 For Radiated Test (Below 30MHz) .......................................................................................... 11 4.4.4 For Radiated Test (30MHz-1GHz) .......................................................................................... 12 4.4.5 For Radiated Test (Above 1GHz) ........................................................................................... 12 4.5 Test Conditions ............................................................................................................................. 13 Report No.: BL-SZ1520008-601 3 4.6 Measurement Results Explanation Example ................................................................................. 14 4.6.1 For conducted test items: ....................................................................................................... 14 4.6.2 For radiated band edges and spurious emission test: ............................................................. 14 5 TEST ITEMS ....................................................................................................................................... 15 5.1 Antenna Requirements .................................................................................................................. 15 5.1.1 Standard Applicable ............................................................................................................... 15 5.1.2 Antenna Anti-Replacement Construction ................................................................................ 15 5.1.3 Antenna Gain ......................................................................................................................... 15 5.2 Number of Hopping Frequency ..................................................................................................... 16 5.2.1 Limit ........................................................................................................................................ 16 5.2.2 Test Procedure ....................................................................................................................... 16 5.3 Peak Output Power ....................................................................................................................... 17 5.3.1 Test Limit ................................................................................................................................ 17 5.3.2 Test Procedure ....................................................................................................................... 17 5.4 Occupied Bandwidth ..................................................................................................................... 18 5.4.1 Limit ........................................................................................................................................ 18 5.4.2 Test Procedure ....................................................................................................................... 18 5.5 Carrier Frequency Separation .......…

Text truncated - open the document above for the full version.

Report No.: BL-SZ1520008-601 99 ANNEX B TEST SETUP PHOTOS B.1 Conducted Test Photo B.2 Conducted Emissions Test Photo Report No.: BL-SZ1520008-601 100 B.3 Radiated Test Photo Below 30MHz 30MHz to 1GHz Report No.: BL-SZ1520008-601 101 Above 1GHz