Z4D173503WiFi module for communication and/or remote operation

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 User Manual 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Wi-Fi Module FCC / IC Statements (Model 173503) Note: this module is integrated at the factory, under direct control of Jarden Consumer Solutions, into appliances that are exempted from FCC Part 15 Subpart B, and is not user serviceable or upgradeable. The WeMo SMART module is a 802.11b/g/n compatible device designed to provide communication between appliances and smart devices. For use in appliances only Front Page Back Page

04/02/2014 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: I hereby appoint Sam Wismer at Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of FCC ID: Z4D173503 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Ivo Marrachinho Regulatory Affairs Specialist 2381 NW Executive Center Drive Boca Raton, FL 33431 P: 561-912-4188 | M: 978-514-0444 [email protected] 2381 NW Executive Center Drive Boca Raton, FL 33431 Ph: (561) 912-4100

CONFIDENTIALITY REQUEST Federal Communications Commission Date: 04/14/2014 Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Sunbeam Products Inc., d/b/a Jarden Consumer Solutions respectfully requests confidentiality of certain materials provided with the submission of the Model 173503 module under FCC ID: Z4D173503 in accordance with 47 CFR 0.457(d) and 47 CFR 0.459. The confidentiality request applies to the (1) schematic diagrams, (2) detailed block diagrams and (3) detailed operational descriptions, contained in this filing and included in the following files: 14-2023 – Schematics.pdf 14-2023 – Block Diagram.pdf 14-2023 – Theory of Operation.pdf The Model 173503 module has been developed at considerable effort and expense by Sunbeam Products Inc., d/b/a Jarden Consumer Solutions. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, Ivo Marrachinho Regulatory Affairs Specialist 2381 NW Executive Center Drive Boca Raton, FL 33431 P: 561-912-4188 | M: 978-514-0444 [email protected] 2381 NW Executive Center Drive Boca Raton, FL 33431 Ph: (561) 912-4100

5015 B. U. Bowman Dr. Buford, GA 30518 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: Z4D173503 To Whom It May Concern: The following application is submitted on behalf of our client, Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions, for evaluation of their model 173503 for certification under FCC Parts 15.247 as a single limited module. The FCC ID: Z4D173503 is a 2.4 GHz IEEE 802.11b/g/n radio module consisting of a single printed circuit board which is designed to be integrated into appliances. The transceiver provides wireless functionality to appliances using Belkin’s WASP (WeMo Appliance Software Protocol). The FCC ID: Z4D173503 does not provide a shield and therefore was evaluated for radiated and power line conducted emissions while integrated inside of a representative host. The FCC ID: Z4D173503 was tested in full to the requirements of the aforementioned rules in the specific host configuration documented in this filing and was found to be in compliance. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

04/18/2014 Ref: Model 173503 module under FCC ID: Z4D173503 To whom it may concern, Per 47 CFR 15.212(a)(1): i. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; The module does not have its own shielding. ii. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; The module contains buffered modulation / data inputs. iii. The module must contain power supply regulation on the module; The module contains its own power supply regulation. iv. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); The module contains a permanently attached antenna. v. The module must demonstrate compliance in a stand-alone configuration; The module was not tested as a stand-alone for power line conducted emissions and radiated emissions. It was tested as a stand-alone for RF conducted emissions. 2381 NW Executive Center Drive Boca Raton, FL 33431 Ph: (561) 912-4100 vi. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labeling requirements); The module is labeled with its own permanently affixed label. vii. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; The module meets all applicable rules and conditions. viii. The module must comply with RF exposure requirements. The module meets applicable RF exposure requirements. Per 47 CFR 15.212(b): In reference to §15.212(b) limited modular approvals, the modular transmitter was evaluated in the specific configuration in its host device. The modular transmitter is installed in its host device in this same configuration at the factory, and is not user accessible or configurable. This establishes full control and maintains full compliance of the end product. Sincerely, Ivo Marrachinho Regulatory Affairs Specialist 2381 NW Executive Center Drive Boca Raton, FL 33431 P: 561-912-4188 | M: 978-514-0444 [email protected]

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 External Photos 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 1: Top View ACS Project: 14-2023 Advanced Compliance Solutions Page 2 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 2: Bottom View ACS Project: 14-2023 Advanced Compliance Solutions Page 3 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 3: Installed in Host – View 1 ACS Project: 14-2023 Advanced Compliance Solutions Page 4 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 4: Installed in Host – View 2 ACS Project: 14-2023 Advanced Compliance Solutions Page 5

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 Label Information 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 1: Sample Label and Location – Module 173503 ACS Project: 14-2023 Advanced Compliance Solutions Page 2 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 2: Sample Label - Host ACS Project: 14-2023 Advanced Compliance Solutions Page 3

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 Internal Photos 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 1: Top View ACS Project: 14-2023 Advanced Compliance Solutions Page 2 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 2: Bottom View ACS Project: 14-2023 Advanced Compliance Solutions Page 3

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 RF Exposure 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 General Information: Applicant: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions ACS Project: 14-2023 Device Category: Mobile Environment: General Population/Uncontrolled Exposure Technical Information: Antenna Type: Printed Inverted-F Antenna Antenna Gain: 1.4 dBi Maximum Transmitter Conducted Power: 22.25 dBm, 167.88 mW Maximum System EIRP: 23.65 dBm, 231.74 mW Exposure Conditions: Greater than 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG π Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 240022.251.00167.881.41.380 200.046 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Installation Guidelines The installation manual should contain text similar to the following advising how to install the equipment to maintain compliance with the FCC RF exposure requirements: RF Exposure In accordance with FCC requirements of human exposure to radio frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 centimeters will be maintained. Conclusion This device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population. ACS Project: 14-2023 Advanced Compliance Solutions Page 2

Certification Test Report FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 14-2023.W06.1A Applicant: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model(s): 173503 Test Begin Date: February 14, 2014 Test End Date: April 10, 2014 Report Issue Date: April 11, 2014 FOR THE SCOPE OF ACCREDITATION UNDER CERTIFICATE NUMBER AT-1533 This report must not be used by the client to claim product certification, approval, or endorsement by ACLASS, ANSI, or any agency of the Federal Government. Project Manager: Reviewed by: Thierry Jean-Charles Kirby Munroe EMC Engineer Director, Wireless Certifications Advanced Compliance Solutions, Inc. Advanced Compliance Solutions, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 82 pages 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 TABLE OF CONTENTS 1 GENERAL ...................................................................................................... 3 1.1 Purpose .............................................................................................................................................. 3 1.2 Applicant Information ..................................................................................................................... 3 1.3 Product Description .......................................................................................................................... 3 1.4 Test Methodology and Considerations ........................................................................................... 3 2 TEST FACILITIES .......................................................................................... 5 2.1 Location ............................................................................................................................................. 5 2.2 Laboratory Accreditations/Recognitions/Certifications ............................................................... 5 2.3 Radiated & Conducted Emissions Test Site Description .............................................................. 6 3 APPLICABLE STANDARD REFERENCES................................................... 8 4 LIST OF TEST EQUIPMENT .......................................................................... 9 5 SUPPORT EQUIPMENT .............................................................................. 10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ............................ 11 7 SUMMARY OF TESTS ................................................................................. 13 7.1 Antenna Requirement – FCC: Section 15.203 ..............................................................................13 7.2 6 dB Bandwidth - FCC: Section 15.247(a)(2) 99% Bandwidth IC: RSS-210 A8.2(a) ................13 7.3 Peak Output Power - FCC Section 15.247(b)(3) IC: RSS-210 A8.4(4) .......................................29 7.4 Band-Edge Compliance and Spurious Emissions-FCC 15.247(d) IC: RSS-210 A8.5 ................37 7.5 Power Spectral Density - FCC Section 15.247(e) IC: RSS-210 A8.2(b) ......................................71 7.6 Power Line Conducted Emissions – FCC: Section 15.207 IC: RSS-Gen 7.2.4 ...........................79 8 CONCLUSION .............................................................................................. 82 Models: 173503 FCC ID: Z4D173503 IC: 9973A-173503 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210 for a limited modular approval. 1.2 Applicant Information Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions 2381 NW Executive ctr dr. Boca Raton, FL 33433 1.3 Product Description The model 173503, WeMo SMART module, is an 2.4 GHz IEEE 802.11b/g/n transceiver. The device is designed to provide some wireless functionality to appliances using Belkin’s WASP (WeMo Appliance Software Protocol). Technical Details Mode of Operation: WLAN 802.11b/g/n Frequency Range: 802.11b/g: 2412 MHz - 2462 MHz 802.11n 20 MHz: 2412 MHz - 2462 MHz 802.11n 40 MHz: 2422 MHz - 2452 MHz Number of Channels: 802.11b/g: 11 802.11n 20 MHz: 11 802.11n 40 MHz: 7 Channel Separation: 5 MHz Modulations: 802.11b: CCK 802.11g/n: OFDM Antenna Type/Gain: Printed Inverted F Antenna, 1.4 dBi Input Power: 5 VDC Model Number: 173503 Test Sample Serial Number(s): 221351S0000062 Test Sample Condition: The equipment was provided in good condition without any physical damage. 1.4 Test Methodology and Considerations The EUT was configured with an RS232 and a LAN cable adapter for programming purposes. A FAIR- RITE model 0431173951 ferrite was used to reduce the emissions for these cables. The EUT was evaluated for radiated, power line and RF conducted emissions for all modes of operations. Preliminary evaluation was performed to determine the worst case data rate configuration for each mode based on RF output power measurement. Where applicable, the results are provided for the worst case, based on the RF output power measurements.. The equipment is designed to be integrated inside specific hosts. The radiated and power line conducted emissions evaluations was performed with the equipment integrated inside of a slow cooker, as described in this document. The digital circuit of the slow cooker was in the idle state during the evaluation. In ACS Report: 14-2023.W06.1A Advanced Compliance Solutions Page 3 of 82 Models: 173503 FCC ID: Z4D173503 IC: 9973A-173503 order for the host to comply to the power line conducted emission requirements, it was modified with a 0.22 uF capacitor (Carli 22K275V-X2) on the AC Line. The EUT was programmed through the RS232 cable addapter using Hyperterminal communicati…

Text truncated - open the document above for the full version.

Certification Exhibit FCC ID: Z4D173503 IC: 9973A-173503 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 14-2023 Manufacturer: Sunbeam Products, Inc. d/b/a Jarden Consumer Solutions Model: 173503 Test Setup Photos 3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 1: Radiated Emissions – Front View ACS Project: 14-2023 Advanced Compliance Solutions Page 2 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 2: Radiated Emissions – Back View ACS Project: 14-2023 Advanced Compliance Solutions Page 3 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 3: RF Conducted Emissions ACS Project: 14-2023 Advanced Compliance Solutions Page 4 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 4: Power Line Conducted Emissions – Front View ACS Project: 14-2023 Advanced Compliance Solutions Page 5 Model: 173503 FCC ID: Z4D173503 IC: 9973A-173503 Figure 5: Power Line Conducted Emissions – Side View ACS Project: 14-2023 Advanced Compliance Solutions Page 6