ZP5BF-UV82LWalkie Talkie

DUAL BAND/DUAL DISPLAY RADIO UV-82 OPERATING MANUAL PREFACE Thank you for purchasing UV-82 Portable Radio, which is a dual band/dual display radio. This easy-to-use radio will deliver you secure, instant and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio. CONTENT 1.­SAFETY INFORMATION 2.­FEATURES AND FUNCTIONS 3.­UNPACKING AND CHECKING EQUIPMENTS 4.­ OPTIONAL ACCESSORIES 5.­ INSTALLATION OF ACCESSORIES 5.1.­ INSTALLING THE ANTENNA 5.2.­ INSTALLING THE BELT CLIP 5.3.­ MICRO­HEADSET INSTALLATION OF EXTERNAL 5.4. – BATTERY INSTALLATION 6.­BATTERY CHARGING 7.­BATTERY INFORMATION 7.1.­INITIAL USE 7.2.­BATTERY TIPS 7.3.­PROLONG BATTERY LIFE 7.4.­BATTERY STORAGE 8.­PARTS, CONTROLS AND KEYS 8.1.­RADIO OVERVIEW 8.2.­ COMMAND/KEY DEFINITION 9.­‘LCD’ DISPLAY 10.­ 1750 Hz TONE FOR ACCESS TO REPEATERS 11.1.­RADIO ON­OFF/VOLUME CONTROL 11.2.­ SELECTING A FREQUENCY OR CHANNEL 12­ADVANCED OPERATION 12.1.­SET MENU DESCRIPTION 12.2.­SHORTCUT MENU OPERATION 12.3.­“SQL” (SQUELCH) 12.4.­FUNCTION “VOX” (VOICE OPERATED TRANSMISSION) 12.5.‐ SELECT WIDEBAND OR NARROW BAND “W/N” 12.6.‐TDR (DUAL WATCH/DUAL RECEPTION) 12.7.­ TOT(TRANSMISSION TIMER) 12.8.­CTCSS/DCS 12.9.­ ANI 12.10.­ DTMFST (DTMF TONE OF TRANSMITTING CODE ) 12.11.­ SC­REV(SCAN RESUME METHOD) 12.12.­ PTT­ID(PTT OR RELEASE PTT TO TRANSMIT THE SIGNAL CODE) 12.13­BCL(BUSY CHANNEL LOCKOUT) 12.14.­ SFT­D(DIRECTION OF FREQUENCY SHIFT) 12.15.­ OFFSET(FREQUENCY SHIFT) 12.16.­STE(STE TAIL TONE ELIMATION) 12.17.­THE INSTRUCTIONS TO SAVE CHANNEL 12.18.­ CTCSS/DCS SCANNING 12.19.­ REPEATER TAIL TONE 13.­CTCSS TABLE 14.­DCS TABLE 15.­TECHNICAL SPECIFICATION 15.1.­GENERAL 15.2. – TRANSMITTER 15.3. ­ RECEIVER 16.­TROUBLESHOOTING 17.­WARRANTY 1.­SAFETY INFORMATION: The following safety precautions shall always be observed during operation, service and repair of this equipment. ◇ This equipment shall be serviced by qualified technicians only. ◇ Do not modify the radio for any reason. ◇ Use only BAOFENG supplied or approved batteries and chargers. ◇ Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. ◇ Turn off your radio prior to entering any area with explosive and flammable materials. ◇ Do not charge your battery in a location with explosive and flammable materials. ◇ To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so. ◇ Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions. ◇ Turn off your radio before entering a blasting area. ◇ For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area. ◇ Do not expose the radio to direct sunlight over a long time, nor place it close to heating source. ◇ When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting. WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting. 2.­FEATURES AND FUNCTIONS: -Dual-band handheld transceiver with display function menu on the display "LCD". - Commercial FM radio receiver (65 MHz ~ 108 MHz). -Frequency Mode/Channel Mode - DTMF encoded. - Incorporates 105 codes "DCS" and 50 privacy codes "CTCSS" programmable. -CTCSS & DCS Scanning - CTCSS & DCS Direct input - Function "VOX" (voice operated transmission). - Alarm function. - Up to 128 memory channels. - Broadband (Wide) / Narrowband (Narrow), selectable. - Display illumination and programmable keyboard. - Function "beep" on the keyboard. - Dual Standby/dual reception. -Crossband reception/transmission - Selectable Frequency Step 6.25/12.5 kHz. - Function "OFFSET" (frequency offset for repeater access). - Frequency reverse - Battery saving function "SAVE". - Timer transmission "TOT" programmable. - Selecting the Scan Mode. - Function Busy Channel Lock "BCLO". - Built-in RX CTCSS/DCS scan - Built-in LED flashlight. - Programmable by PC. - Level Threshold "Squelch" adjustable from 0 to 9. -Tone end of transmission - Built-in key lock 3.­UNPACKING AND CHECKING EQUIPMENTS: Carefully unpack the transceiver. We recommend that you identify the items listed in the following before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealers immediately. Battery Pack Antenna Adapter Drop-in Charging Tray Belt Clip Handstrap Note: - Items included in the package, may differ from those listed in the table above depending on the country of purchase. For more information, consult your dealer or vendor. 4.­ OPTIONAL ACCESSORIES: Note: ‐ Consult the dealer or retailer for information about options available. 5.­ INSTALLATION OF ACCESSORIES: 5.1.­ INSTALLING THE ANTENNA: Install the antenna as shown in the figure below and turn it clockwise until it stops. Note: ‐ When installing the antenna, don’t rotate it by its top, holding it by its base and turn. ‐ If you use an external antenna, make sure the ‘SWR’ is about 1.5:1 or less, to avoid damage to the transceiver's final transistors. ‐ Do not hold the antenna with your hand or wrap the outside of it to avoid bad operation of the transceiver. ‐ Never transmit without an antenna. 5.2.­ INSTALLING THE BELT CLIP: If necessary, install the belt clip at the rear of the battery compartment cover as shown in the figure below. Note: ‐ Do not use any kind of glue to fix the screw on the belt clip. The solvents Glue may damage the battery casing. 5.3.­ MICRO­HEADSET INSTALLATION OF EXTERNAL: Plug the external micro-headset connector into the jack of ‘SP. & MIC’ of the transceiver …

Text truncated - open the document above for the full version.

FUJIAN NAN'AN BAOFENG ELECTRONICS CO.,LTD. 2/F.,No.1Bldg.,Boyi Industrial Garden,4 th Gongye Rd.Zhicun Dashi Street,Panyu Dis.,Guangzhou,China TEL: (86) 020-34796226 FAX: (86) 020-34796116 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. { FUJIAN NAN'AN BAOFENG ELECTRONICS CO.,LTD.} would like the following documents regarding this submission for FCC ID: ZP5BF-UV82L to be kept confidential. 1、 Schematics 2、 Operational Description 3、 Block Diagram 4、 Tune Up Procedure 5、 Part List The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, FUJIAN NAN'AN BAOFENG ELECTRONICS CO.,LTD.

Fujian Nan’an Baofeng Electronic Co., Ltd. To: Shenzhen Timeway Technology Consulting Co., Ltd. Date: 2015-07-31 FCC ID: ZP5BF-UV82L Statement We need adding model for FCC approval is UV-82L Trade Mark is N/A The original Model No. is GT-5 , The original Trade Mark is N/A . We hereby state that these models are identical in interior structure, electrical circuits and components, different appearance with different model names for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, Signature: Company Name: Fujian Nan’an Baofeng Electronic Co., Ltd.

FUJIAN NAN'AN BAOFENG ELECTRONICS CO., LTD. CHANGFU INDUSTRIAL ZONE, XIAMEI, NNA’AN, QUANZHOU, FUJIAN, CHINA TEL: 00886-595-86767889 FAX: 00886-595-86753889 Declaration Date: 30 July, 2015 Federal Communications Commissions Authorization & Evaluation Division 7435 Oakland Mills Road Colombia, MD 21046 Product Name: Walkie Talkie Model: GT-5, UV-82L FCC ID: ZP5BF-UV82L Dear whom may be concerned: We declare this equipment meets the requirements of FCC Rules, Parts 90.203 (e) and (g) as applicable. Programming of this product's transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment's external operation. We also declare that the device will not be marketed to USA users with the frequency band Which is not allowed by rule part 90. It will be a violation of FCC rules if this device is operated on unauthorized frequencies inside the USA. Sincerely,

Outside View Of GT-5 Outside View Of GT-5 Belt Belt Outside View Of UV-82L

BAOFENG Walkie Talkie Model: UV-82L FCC ID: ZP5BF-UV82L Frequency: 136-174MHz/400-480MHz Note: The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase

Interior View Of GT-5 Interior View Of GT-5 Interior View Of GT-5 Interior View Of GT-5

Report No.: BL-SZ1570083-701 2 / 77 Revision History Version Issue Date Revisions Rev. 01 Jul. 29, 2015 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................................ 4 1.1 Identification of the Testing Laboratory ............................................................................................... 4 1.2 Identification of the Responsible Testing Location .............................................................................. 4 1.3 Test Environment Condition ................................................................................................................ 4 1.4 Announce ............................................................................................................................................. 4 2 PRODUCT INFORMATION ........................................................................................................................ 6 2.1 Applicant ............................................................................................................................................... 6 2.2 Manufacturer ........................................................................................................................................ 6 2.3 General Description for Equipment under Test (EUT) ........................................................................ 6 2 .4 Technical Information ........................................................................................................................... 6 2.5 Ancillary Equipment ............................................................................................................................. 7 3 SUMMARY OF TEST RESULTS ............................................................................................................... 8 3.1 Test Standards ..................................................................................................................................... 8 3.2 Device Category and SAR Limit .......................................................................................................... 8 3.3 Summary of SAR Value ..................................................................................................................... 10 3.4 SAR Test Uncertainty ........................................................................................................................ 11 4 SAR MEASUREMENT SYSTEM ............................................................................................................. 13 4.1 Definition of Specific Absorption Rate (SAR) .................................................................................... 13 4.2 SATIMO SAR System ........................................................................................................................ 13 5 SYSTEM VERIFICATION ......................................................................................................................... 20 5.1 Antenna Port Test Requirement ........................................................................................................ 20 5.2 Purpose of System Check ................................................................................................................. 20 5.3 System Check Setup ......................................................................................................................... 20 6 EUT TEST POSITION CONFIGURATUONS .......................................................................................... 21 6.1 Head Exposure Conditions ................................................................................................................ 21 6.2 Body-worn Position Conditions .......................................................................................................... 22 Report No.: BL-SZ1570083-701 3 / 77 7 SAR MEASUREMENT PROCEDURES .................................................................................................. 24 7.1 SAR Measurement Process Diagram ................................................................................................ 24 7.2 SAR Scan General Requirements ..................................................................................................... 25 7.3 SAR Measurement Procedure ........................................................................................................... 26 7.4 Area & Zoom Scan Procedures ......................................................................................................... 26 7.5 PTT MEASUREMENT PROCEDURES ............................................................................................ 26 8 CONDUCTED RF OUPUT POWER ........................................................................................................ 27 9 SAR TEST RESULTS............................................................................................................................... 28 9.1 Test Result (1g value) ........................................................................................................................ 28 9.2 SAR Measurement Variability ............................................................................................................ 29 10 TEST EQUIPMENTS LIST ....................................................................................................................... 30 ANNEX A SIMULATING LIQUID VERIFICATION RESULT ....................................................................... 31 A NNEX B SYSTEM CHECK RESULT ........................................................................................................ 32 ANNEX C TEST DATA................................................................................................................................. 37 ANNEX D EUT PHOTO ....................................................................................…

Text truncated - open the document above for the full version.

ISO/IEC17025Accredited Lab. Report No: FCC 1501207 File reference No: 2015-07-29 Applicant: Fujian Nan’an Baofeng Electronic Co., Ltd. Product: walkie talkie Model No: UV-82L, GT-5 Trademark: N/A Test Standards: FCC Part 90 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10 and FCC Part 90, regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: July 29, 2015 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Room 512-519, 5/F., East Tower, Building 4, Anhua Industrial Zone, Futian District, Shenzhen, Guangdong, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No: FCC1501207 Page 2 of 78 Date: 2015-07-29 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAL. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAL-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAL/AC01:2002 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 899988. IC- Registration No.: IC5205A-02 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration IC No.: 5205A-02. Report No: FCC1501207 Page 3 of 78 Date: 2015-07-29 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration.................................................................................................... 5 1.6 Test Uncertainty.................................................................................................5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 5 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 6.0 Frequency Tolerance..........................................................................................12 7.0 Emission Bandwidth and Mask............................................................................. 21 8.0 Unwanted Radiation.......................................................................................... 35 9.0 Modulation Characteristics................................................................................... 42 10.0 Maximum transmitter Power (Conducted …

Text truncated - open the document above for the full version.

Conducted test View-- Radiated emission test view