ZPNTPM202TPMS SENSOR

BLE TPMS SENSOR TPM202 TPM202631 FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED Statement: For Canada, the “compliance statement and unlicensed device usage conditions” which must be shown in the user manual has changed. It should now read like this: This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, (2) this device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 1) This equipment is not suitable for use in locations where children are likely to be present 2) High or low extreme temperatures: -30°C-75°C 3) Do not replace the battery with an incorrect type (battery type: CR2050W) 4) Do not dispose the battery into fire or a hot oven 5) Do not leave the battery in an extremely high temperature 6) Do not subject the battery to extremely low air pressure Product Warning 1. Please do not operate the APP or TPMS receiving device while riding a motorcycle. Failure to concentrate on riding a motorcycle may result in serious consequences such as injury or death. The user will bear all risks and responsibilities! 2. This TPMS Sensor adopts wireless signal transmission. In some case, the system may receive weak signal or no signal due to interference, wrong operation method or wrong installation method. If the APP or TPMS receiving device displays an abnormal icon and emits a warning sound during riding the motorcycle, please move the vehicle away from the current location and check again. There may be other signal interference nearby, and ride the vehicle to a nearby tire service location for inspection. 3. If the battery status of the TPMS sensor is low (if abnormal conditions exist, the low battery status may make the TPMS sensors emit signals to warn the driver continuously, so that the battery life will be shorter than expected). Please go to the designated installation site for inspection as soon as possible, and check whether the sensor needs to be replaced. 4. Please change the sensor when the low sensor battery warning is displayed, it may cause the TPMS not working normally. The user will bear all risks and responsibilities. 5. When disassembling and installing tires, please avoid collision with the sensor when using tire removal and installation equipment. 6. The use of tire sealants, such as tire sealants filled via the valve, will adversely affect the operation of the sensor. The company is exempt from all consequences 7. Do not place the TPMS sensor in contact with any chemicals, as this may damage the sensor and prevent it from working properly. 8. Do not exceed the speed limit of the product and the vehicle. Exceeding the speed limit may cause damage to the sensor and prevent normal operation. Although this product has the function of detecting the tire pressure of the vehicle and warning the driver in case of abnormal tire pressure, it cannot be used to replace or reduce the driver's usual care obligations and any inspections or operations that should be performed before or while driving. Drivers should remain alert under any driving conditions, comply with all safe driving standards, and comply with all traffic rules. The company shall not be liable for any damage caused by the driver's failure to comply with the foregoing matters. Product Part List TPMS Sensor x 2 Valve kit x 2 Tire pressure monitoring sensor installation ◼ Please go to a qualified service location for TPMS sensor installation and setting. ◼ When removing or installing tires, the removal tool should avoid the valve position to avoid damage to the TPMS sensor.

BLE TPMS SENSOR TPM202 TPM202631 FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED Statement: For Canada, the “compliance statement and unlicensed device usage conditions” which must be shown in the user manual has changed. It should now read like this: This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, (2) this device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 1) This equipment is not suitable for use in locations where children are likely to be present 2) High or low extreme temperatures: -30°C-75°C 3) Do not replace the battery with an incorrect type (battery type: CR2050W) 4) Do not dispose the battery into fire or a hot oven 5) Do not leave the battery in an extremely high temperature 6) Do not subject the battery to extremely low air pressure Product Warning 1. Please do not operate the APP or TPMS receiving device while riding a motorcycle. Failure to concentrate on riding a motorcycle may result in serious consequences such as injury or death. The user will bear all risks and responsibilities! 2. This TPMS Sensor adopts wireless signal transmission. In some case, the system may receive weak signal or no signal due to interference, wrong operation method or wrong installation method. If the APP or TPMS receiving device displays an abnormal icon and emits a warning sound during riding the motorcycle, please move the vehicle away from the current location and check again. There may be other signal interference nearby, and ride the vehicle to a nearby tire service location for inspection. 3. If the battery status of the TPMS sensor is low (if abnormal conditions exist, the low battery status may make the TPMS sensors emit signals to warn the driver continuously, so that the battery life will be shorter than expected). Please go to the designated installation site for inspection as soon as possible, and check whether the sensor needs to be replaced. 4. Please change the sensor when the low sensor battery warning is displayed, it may cause the TPMS not working normally. The user will bear all risks and responsibilities. 5. When disassembling and installing tires, please avoid collision with the sensor when using tire removal and installation equipment. 6. The use of tire sealants, such as tire sealants filled via the valve, will adversely affect the operation of the sensor. The company is exempt from all consequences 7. Do not place the TPMS sensor in contact with any chemicals, as this may damage the sensor and prevent it from working properly. 8. Do not exceed the speed limit of the product and the vehicle. Exceeding the speed limit may cause damage to the sensor and prevent normal operation. Although this product has the function of detecting the tire pressure of the vehicle and warning the driver in case of abnormal tire pressure, it cannot be used to replace or reduce the driver's usual care obligations and any inspections or operations that should be performed before or while driving. Drivers should remain alert under any driving conditions, comply with all safe driving standards, and comply with all traffic rules. The company shall not be liable for any damage caused by the driver's failure to comply with the foregoing matters. Product Part List TPMS Sensor x 2 Valve kit x 2 Tire pressure monitoring sensor installation ◼ Please go to a qualified service location for TPMS sensor installation and setting. ◼ When removing or installing tires, the removal tool should avoid the valve position to avoid damage to the TPMS sensor.

QF094234 Page 1 of 1 Revision 0 Authority to Act as Agent Date: 2020-08-26 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern: I appoint TUV Taiwan to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Whe FCC oU IndXVWU\ Canada¶V UegXlaWionV Zill haYe affi[ed Wo iW a label idenWical Wo WhaW submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with CUB ELECPARTS INC / No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: Permanent By : Wing Huang (Signature) (Print Name) Title : Quality System Dept. / Manager Telephone : +886-4-7782010 On behalf of : CUB ELECPARTS INC (Company Name)

CUB ELECPARTS INC No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 Confidentiality Letter Date: 2020-08-26 Subject: Confidentiality Request for FCC ID: ZPNTPM202 and IC: 9959A-TPM202 ; Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Part List/Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent UVer¶V ManXal CUB ELECPARTS INC has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04- 1705. Sincerely, By: Wing Huang (Signature/Title) (Print name)

CUB ELECPARTS INC No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 31-Aug-20 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: ZPNTPM202 ISED ID: 9959A-TPM202 HVIN: TPM202 TPM202 , TPM202631 , TPM202XXX , TPM202­XXX , B121­XXXXXX , B121­XXXXXX­XXX , B121­033XXX­XXX , B121­033NA1­ XXX , 44705­ACK­00 , 44705­JC2­00 , 44705­XXX­XX 1. For the marketing purpose 2. Where X may be any alpha character “a”­“z”, ”A”­“Z”, or numeric character “0” ­“9”,or ­, ( , ) , or blank or combination of alpha and numeric characters. Declaration on Similarity We herewith confirm that for the models listed above the RF Transmitter Module is Electrically Identical. The differences are in the model numbers and in the digital data interface. ___________________ Wing Huang (Signature) (Printed)

QF094234 Page 1 of 1 Revision 0 Authority to Act as Agent Date: 2020-08-26 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern: I appoint TUV Taiwan to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Whe FCC oU IndXVWU\ Canada¶V UegXlaWionV Zill haYe affi[ed Wo iW a label idenWical Wo WhaW submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with CUB ELECPARTS INC / No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: Permanent By : Wing Huang (Signature) (Print Name) Title : Quality System Dept. / Manager Telephone : +886-4-7782010 On behalf of : CUB ELECPARTS INC (Company Name)

CUB ELECPARTS INC No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 Confidentiality Letter Date: 2020-08-26 Subject: Confidentiality Request for FCC ID: ZPNTPM202 and IC: 9959A-TPM202 ; Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Part List/Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent UVer¶V ManXal CUB ELECPARTS INC has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04- 1705. Sincerely, By: Wing Huang (Signature/Title) (Print name)

CUB ELECPARTS INC No.6,Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan 506 31-Aug-20 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: ZPNTPM202 ISED ID: 9959A-TPM202 HVIN: TPM202 TPM202 , TPM202631 , TPM202XXX , TPM202­XXX , B121­XXXXXX , B121­XXXXXX­XXX , B121­033XXX­XXX , B121­033NA1­ XXX , 44705­ACK­00 , 44705­JC2­00 , 44705­XXX­XX 1. For the marketing purpose 2. Where X may be any alpha character “a”­“z”, ”A”­“Z”, or numeric character “0” ­“9”,or ­, ( , ) , or blank or combination of alpha and numeric characters. Declaration on Similarity We herewith confirm that for the models listed above the RF Transmitter Module is Electrically Identical. The differences are in the model numbers and in the digital data interface. ___________________ Wing Huang (Signature) (Printed)

Appendix EP Photographs of EUT Page 1 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 2 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 3 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202

Appendix EP Photographs of EUT Page 1 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 2 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 3 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202

BLE TPMS SENSOR TPM202 Label and Label Placement TPMS-產品管理部 01521(陳宜宗) 2020/8/28 下午 02:20:23

BLE TPMS SENSOR TPM202 Label and Label Placement TPMS-產品管理部 01521(陳宜宗) 2020/8/28 下午 02:20:23

Appendix EP Photographs of EUT Page 4 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 5 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 6 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 7 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Antenna

Appendix EP Photographs of EUT Page 4 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 5 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 6 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Appendix EP Photographs of EUT Page 7 of 7 NN20C8K7 (P15C-BLE) NN20UBJF (RSS247-BLE) Product: BLE TPMS SENSOR Type Identification: TPM202 Antenna

Produkte Products Prü fbericht - Nr.: Test Report No. NN20C8K7 (P15C-BLE) 001 Seite 25 von 25 Page 25 of 25 6. Safety Human Exposure 6.1 RF Exposure Compliance 6.1.1 SAR Test Exclusion Thresholds Results Since the maximum output power of the transmitter is 2.83 mW < 10 mW (Distance: 5 mm), hence the EUT is excluded from SAR evaluation according to FCC KDB publication 447498 D01: Mobile Portable RF Exposure.

Produkte Products Prü fbericht - Nr.: Test Report No. NN20C8K7 (P15C-BLE) 001 Seite 25 von 25 Page 25 of 25 6. Safety Human Exposure 6.1 RF Exposure Compliance 6.1.1 SAR Test Exclusion Thresholds Results Since the maximum output power of the transmitter is 2.83 mW < 10 mW (Distance: 5 mm), hence the EUT is excluded from SAR evaluation according to FCC KDB publication 447498 D01: Mobile Portable RF Exposure.

Prü fbericht - Produkte Test Report - Products Prü fbericht-Nr.: Test report no.: NN20C8K7 (P15C-BLE) 001 Auftrags-Nr.: Order no.: 238490052 Seite 1 von 25 Page 1 of 25 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 06-Aug-2020 Auftraggeber: Client: CUB ELECPARTS INC. No. 6, Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan Prü fgegenstand: Test item: BLE TPMS SENSOR Bezeichnung / Typ-Nr.: Identification / Type no.: TPM202, TPM202631, TPM202-XXX, B121-XXXXXX, B121-XXXXXX-XXX, B121- 033XXX-XXX, B121-033NA1-XXX, 44705-ACK-00, 44705-JC2-00, 44705-XXX-XX Auftrags-Inhalt: Order content: FCC Part 15C Test report (BLE) Prü fgrundlage: Test specification: FCC 47CFR Part 15: Subpart C Section 15.247 Wareneingangsdatum: Date of sample receipt: 12-Aug-2020 Prü fmuster-Nr.: Test sample no: A002887276-011 ~ 013 A002887276-014 ~ 016 Prü fzeitraum: Testing period: 18-Aug-2020~24-Aug-2020 Ort der Prü fung: Place of testing: EMC/RF Laboratory Taipei Prü flaboratorium: Testing laboratory: Taipei Testing Laboratories Prü fergebnis*: Test result*: Pass ü berprü ft von: reviewed by: Ryan W.T. Chen genehmigt von authorized by: Brenda S.H. Chen Datum: 02-Sep-2020 Date: Datum: 02-Sep-2020 Date: Stellung / Position: Project Manager Stellung / Position: Project Manager Sonstiges / Other: The series models are for the marketing purpose. Where X may be any alpha character "a"-"z", "A"-"Z", or numeric character "0"-"9", or -, (,), or blank or combination of alpha and numeric characters. Zustand des Prü fgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prü fbericht bezieht sich nur auf das o.g. Prü fmuster und darf ohne Genehmigung der Prü fstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prü fzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland Taiwan Ltd. 11F., No. 758, Sec. 4, Bade Rd., Taipei 105, Taiwan, R.O.C. Mail: [email protected] Web: www.tuv.com Produkte Products Prü fbericht - Nr.: Test Report No. NN20C8K7 (P15C-BLE) 001 Seite 2 von 25 Page 2 of 25 TEST SUMMARY Report Section FCC Clause Test Item Result 5.1.1 15.247(b) & 15.203 Antenna Requirement Pass 5.1.2 15.247(b)(3) Peak Output Power Pass 5.1.3 15.247(a)(2) 6 dB Bandwidth Pass 5.1.3 2.1049 99% Occupied Bandwidth Pass 5.1.4 15.247(e) Power Spectral Density Pass 5.1.5 15.247(d) Conducted Spurious Emissions and Band Edges Pass 5.1.6 15.247(d) & 15.205 & 15.209 Radiated Spurious Emissions and Band Edges Pass - 15.207 Mains Conducted Emission N/A 6.1 FCC KDB 447498 D01 v06 RF Exposure Compliance Pass Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Produkte Products Prü fbericht - Nr.: Test Report No. NN20C8K7 (P15C-BLE) 001 Seite 3 von 25 Page 3 of 25 Contents HISTORY OF THIS TEST REPORT .............................................................................. 5 1. GENERAL REMARKS ............................................................................................. 6 1.1 COMPLEMENTARY MATERIALS ............................................................................... 6 1.2 DECISION RULE OF CONFORMITY ........................................................................... 6 2. TEST SITES .......................................................................................................... 7 2.1 TEST LABORATORY .............................................................................................. 7 2.2 TEST FACILITY ...................................................................................................... 7 2.3 TRACEABILITY ...................................................................................................... 8 2.4 CALIBRATION ....................................................................................................... 8 2.5 MEASUREMENT UNCERTAINTY ............................................................................... 8 3. GENERAL PRODUCT INFORMATION ......................................................................... 9 3.1 PRODUCT FUNCTION AND INTENDED USE ............................................................... 9 3.2 SYSTEM DETAILS AND RATINGS ............................................................................. 9 3.3 NOISE GENERATING AND NOISE SUPPRESSING PARTS .......................................... 10 3.4 SUBMITTED DOCUMENTS ..................................................................................... 10 4. TEST SET-UP AND OPERATION MODES ................................................................. 11 4.1 PRINCIPLE OF CONFIGURATION SELECTION .......................................................... 11 4.2 CARRIER FREQUENCY AND CHANNEL ................................................................... 11 4.3 TEST OPERATION AND TEST SOFTWARE ............................................................... 12 4.4 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................. 13 4.5 TEST SETUP DIAGRAM ........................................................................................ 13 5. TEST RESULTS ................................................................................................... 14 5.1 TRANSMITTER REQUI…

Text truncated - open the document above for the full version.

Prü fbericht - Produkte Test Report - Products Prü fbericht-Nr.: Test report no.: NN20C8K7 (P15C-BLE) 001 Auftrags-Nr.: Order no.: 238490052 Seite 1 von 25 Page 1 of 25 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 06-Aug-2020 Auftraggeber: Client: CUB ELECPARTS INC. No. 6, Lane 546, Sec. 6, Changlu Road, Fuhsin Township, Changhua County, Taiwan Prü fgegenstand: Test item: BLE TPMS SENSOR Bezeichnung / Typ-Nr.: Identification / Type no.: TPM202, TPM202631, TPM202-XXX, B121-XXXXXX, B121-XXXXXX-XXX, B121- 033XXX-XXX, B121-033NA1-XXX, 44705-ACK-00, 44705-JC2-00, 44705-XXX-XX Auftrags-Inhalt: Order content: FCC Part 15C Test report (BLE) Prü fgrundlage: Test specification: FCC 47CFR Part 15: Subpart C Section 15.247 Wareneingangsdatum: Date of sample receipt: 12-Aug-2020 Prü fmuster-Nr.: Test sample no: A002887276-011 ~ 013 A002887276-014 ~ 016 Prü fzeitraum: Testing period: 18-Aug-2020~24-Aug-2020 Ort der Prü fung: Place of testing: EMC/RF…

Text truncated - open the document above for the full version.