2A46G-M3ARC3AHXAG Agricultural Remote Controller 3 Pro

XAG Agricultural Remote Controller 3 Pro User Manual Version 1.0 EN To User Dear user, thank you for choosing XAG's products. For safety purposes and better user experience, it is highly recommended that you read this manual carefully and strictly follow the instructions hereof. Contact Us Manufacturer: Guangzhou Xaircraft Technology CO., LTD. Add: XSpace, No.115, Gaopu Road, Guangzhou, Guangdong Province, China Technical Support Team: [email protected] www.xa.com/en 1 Introduction The XAG Agricultural Remote Controller 3 Pro(ARC3 Pro) is a screen-free two-handed remote controller for agricultural use. High-precision mapping is available when it is equipped with the special RTK positioning module. Its four knobs and many buttons, specially designed for the XAG agricultural drones, plus WiFi+4G networking and dual SIM dual standby make it possible to operate the farm equipment easily without an app, thus enhancing the efficiency of manual remote operation. List of Items Please see that all of the following items are present when unpacking the box. Should there be any item missing, please contact your seller. RTK Module ×1 Charger ×1 USB-A To Type-C Cable ×1 ARC3 Pro ×1 Phone Holder ×1 www.xa.com/en 2 1. Antenna 2. RTK Module 3. Phone Holder 4. Joystick 5. Fn Button 6. Buzzer 7. Power Button 8. Charging Port 9. Stop Button 10. L2 Button 11. L1 Button 12. F1 Knob 13. F2 Knob 14. SIM2 Card Slot 15. USB-C Port 16. SIM1 Card Slot 17. F3 Knob 18. F4 Knob 19. R1 Button 20. R2 Button Overview ① ③ ② ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑫⑬ ⑭⑯ ⑰ ⑮ ⑳ ⑱ ⑲ ⑪ ⑩ www.xa.com/en 3 ButtonOperationDescription Stop Button Short Press Joystick Self-calibration Mode: next Hover the aircraft; Remote controller goes into manual operation mode Long PressKeep the aircraft on "Auxiliary Mode" or "Autono- mous Mode" Fn Button Long Press Enter/exit Mapping Mode; In Mapping Mode, short press L1 to mark the current position, and short press L2 to undo the previous mark. In Mapping Mode, remote controller can only be used for mapping rather than piloting the aircraft. Long Press Fn Button+Stop Button Return the aircraft Fn Button+push both joysticks to the bottom left limit Enable Joystick Self-calibration Mode F1 Knob TwiddleAuxiliary Mode: adjust route spacing Short PressEnable obstacle avoidance Long PressDisable obstacle avoidance F2 Knob TwiddleAuxiliary Mode: adjust route direction Short PressDisable Terrain-following Mode Long PressEnable Terrain-following Mode F3 Knob TwiddleAdjust droplet size while the aircraft is spraying Short PressToggle one-side/two-side spraying Long PressToggle variable-rate/constant-rate spraying F4 Knob TwiddleAdjust the flow rate when the aircraft is spraying Short PressStop spraying Long PressStart spraying About Buttons www.xa.com/en 4 L1 Button Short Press Mapping Mode: Fly to Mark, Mark by Remote Con- troller Auxiliary Mode: proceed with "Auxiliary Mode" [1] Long Press Mapping Mode: form a close shape Auxiliary Mode: Enable "Auxiliary Mode"; Long press again to set the current height as the alti- tude for the auxiliary mode. L2 Button Short Press Mapping Mode: undo the mark in "Fly to Mark", undo the mark in "Mark by Remote Controller" Auxiliary Mode: turn around to the left row Long PressAuxiliary Mode: move to the left row R1 ButtonShort PressToggle forward/downward PSL camera R2 Button Short PressAuxiliary Mode: turn around to the right row Long PressAuxiliary Mode: move to the right row [1]: In Auxiliary Mode, you can adjust the height of the aircraft by moving the "throttle" and the aircraft will automatically return to the default height after releasing the "throttle". Indicator Description One Green Light On Battery level: 1%-20%, please charge Two Green Lights OnBattery level: 21%-35% Three Green Lights OnBattery level: 36%-50% Four Green Lights OnBattery level: 51%-65% Five Green Lights OnBattery level: 66%-80% Six Green Lights OnBattery level: 81%-100% Status Indicators When the remote controller is off, short the press power button to check the battery level. Battery Indicator Description Solid Green Battery level: 51%-100% Solid YellowBattery level: 21%-50% Solid RedBattery level: 1%-20% When the remote controller is on, the indicators will tell you the status of the remote controller and the aircraft. www.xa.com/en 5 Battery Indicator Description Single Flashing GreenFast charging OffOff Mobile Network Indicator Description Solid Green LAN communication normal Single Flashing GreenLAN/WAN communication Solid YellowLNT mode communication normal Solid RedCommunication error OffSIM card not detected External Device Indicator Description Solid Green RTK positioning, ready for mapping Double Flashing GreenSingle positioning, ready for mapping Single Flashing GreenPositioning, cannot map Solid YellowRTK module sleeping Solid RedRTK module communication error OffRTK module not detected Wireless Communication Indicator Description Solid Green Communication with aircraft normal Single Flashing GreenInitializing remote controller communication Single Flashing YellowPairing network OffNo aircraft connected Function Indicator A Description Solid Green Manual control Single Flashing GreenAuxiliary mode Solid YellowManual flight mapping Single Flashing Yellow Aircraft returning or making an emergency landing Solid RedJoystick error, please calibrate OffFully autonomous mode www.xa.com/en 6 Buzzer Description Long Beep Remote controller: power on/off, add a de- vice One Short BeepShort press any button or twiddle a knob Two Short Beep Long press any button, or link, calibrate or charge the remote controller Three Short Beeps (consecutive) Warning of the payload system or smart sys- tem of the aircraft Three Long Beeps (consecutive) Low battery warning or system error of the remote controller Buzzer When the buzzer is on, the beep code will tell you the status of the remote controller and the aircraft. Joystick Mode The Joystick Mode is divided into Japanese Hand, American Hand and Chinese Hand. The default mode …

Text truncated - open the document above for the full version.

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 Guangzhou Xaircraft Technology CO.,LTD. Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both Pegasus Spray Inc. (“Agent”) and Guangzhou Xaircraft Technology CO.,LTD. (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I Zoe Qin. HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : Guangzhou Xaircraft Technology CO.,LTD. Contact Name : Zoe Qin Address : Block C, No.115, Gaopu Road, Tianhe District, GuangzhouCity, Guangdong, P.R.China Telephone No : +86（020）85207212 Email : [email protected] FCC ID : Applicant FRN : 0032030363 Signature: ____________________________________ Date: ____________________________________ I Arthur Chen HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated above. Agent Company Name : Pegasus Spray Inc. Contact Name : Arthur Chen Address : 2235 79th Ave NE, Medina, WA 98039 Telephone No : +1 5038661228 Email : [email protected] Agent FRN : 0033696949 Signature: ____________________________________ Date: ____________________________________ 2023-06-07 _ ____________________ Jan. 12, 2023 ___________________ Ate 2A46G-M3ARC3AH

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1 /25/2023 Guangzhou Xaircraft Technology CO.,LTD. Attention: Application Examiner Re: Cov ered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR part s §2.903 and §2.911(d)(5)(ii) of t he FCC rules Applicant: Guangzhou Xaircraft Technology CO.,LTD. FCC ID: 2A46G-M3ARC3AH To whom it may concern, Guangzhou Xaircraft Technology CO.,LTD. (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from rece ivin g an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate ther eof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ [Signature of authorized Proprietor, Partner or Authorized Officer] Zoe Qin Product certification Engineer Guangzhou Xaircraft Technology CO.,LTD. 2023-06- 07

Guangzhou Xaircraft Technology CO.,LTD. 2023-06-07 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Guangzhou Xaircraft Technology CO.,LTD. FCC ID: 2A46G-M3ARC3AH To Whom It May Concern: We, Guangzhou Xaircraft Technology CO.,LTD., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2A46G-M3ARC3AH under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2023-06-07). The Limited Agency Agreement expires on (2024-06- 07) , unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial o f federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Zoe Qin Product certification Engineer

1(2) Guangzhou Xaircraft Technology CO.,LTD. Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2A46G-M3ARC3AH To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of [please enter 1 to 180] days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure 2(2) Parts List Test Setup Photos External Photos Internal Photos Users M anual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sinc erely, _________________ Zoe Qin Product certification Engineer 2023-06- 07

External Photo External Photo External Photo External Photo External Photo External Photo External Photo External Photo External Photo

 
 
      !"#$% &'(' )*+($!",-./0*. 0+ 123455655353345377 8  9353  !"#$% &'(' )*+($!",-./0*. 901: ;;;;;;;;; 8  ++<+353%=  !"#$% &'(' )*+($!",-./0*. 901: ;;;;;;;;; 8 71>-71?  !"#$% &'(' )*+($!",-./0*. >>;;;;;;;;; %11"'&(*'  >B *-!*''7C' DDDEDDDDDD DDDEDDDDDD DDEDDDDDDD ;;;;;;;;;;;  &!-$&!   FG8HIJK F  !) (*'2 *L5.3.5   !"#$% &'(' )*+($!",-./0*. 0+ 1234556553 53345377 ++<+353%=  !"#$% &'(' )*+($!",-./0*. 901: ;;;;;;;;; 9353  !"#$% &'(' )*+($!",-./0*. 901: ;;;;;;;;; %11"'&(*' >B *-!*''7C'   71>-71? MNOPQR RSTUVWXVPYWXS Z **',6[55B 1$\.7[= <!]*^=14=3.13=3.1 _*]*^=31 1'``Z(a-/:.33/ ]> /+& !$2&`*'& (*/  !"#$-&*,/ !"!"/C.>.-$&!  !) (*'b, !"#$% &'(' )*+($!",-./ 0*. +$&`c&((B]&`d&*$C '*3)*$@-->`. _]' *&!&``be(***$)d&!"*d(!&*&!` f3g*$&`c&(B ,!*( `$ 'B)&!*')'!(/ ! fg*$&`c&(B`* ((]* !,&!*')'!('(&c/ &!(&!"&!*')'!(*$ *B ,( `!`&' ]' *&!. @--<216A71>-71? -!* &!`@--<216A93531 FJ G8 +$&`c&((B]&`d&*$C '*3)*$@-->`.  _]' *&!&``be(***$)d&!"*d(!&*&! ` f3g*$&`c&(B ,!*( `$ 'B)&!*')'!(/  ! fg*$&`c&(B`* ((]* !,&!*')'!('(&c / &!(&!"&!*')'!(*$ *B ,( `!`&'  ]' *&!. @--<216A71>-71?-!* &!`@--<216A93531 8 8 71>-71?  !"#$% &'(' )*+($!",-./0*. >>;;;;;;;;; %11"'&(*'  >B *-!*''7C' DDDEDDDDDD DDDEDDDDDD DDEDDDDDDD ;;;;;;;;;;;  &!-$&! 

Internal Photo Internal Photo Internal Photo GSM/WCDMA/LTE ANT 2.4G&5.8G WIFI ANT Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo Internal Photo

Guangzhou Xaircraft Technology CO.,LTD TEST REPORT SCOPE OF WORK FCC TESTING– M3ARC3AH REPORT NUMBER 230403080SZN-002 ISSUE DATE [REVISED DATE] 21 June 2023 [--------------------] PAGES 103 DOCUMENT CONTROL NUMBER FCC SAR_b © 2017 INTERTEK Intertek Report No.: 230403080SZN-002 TRF No.: FCC SAR_b Page 1 of 88 SAR TEST REPORT For Guangzhou Xaircraft Technology CO.,LTD XAG Agricultural Remote Controller 3 Pro Model No.: M3ARC3AH FCC ID: 2A46G-M3ARC3AH Report No.: 230403080SZN-002 Issue Date: 21 June 2023 Prepared by Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Telephone: 86-755-8601 6288 Fax: 86-755-8601 6751 • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • The test report only allows to be revised only within the report defined retention period unless further standard or the requirement was noticed Intertek Report No.: 230403080SZN-002 TRF No.: FCC SAR_b Page 2 of 88 Table of Contents 1 GENERAL INFORMATION .......................................................................................................................................... 3 2 EQUIPMENT UNDER TEST (EUT) TECHNICAL DESCRIPTION ...................................................................................... 5 3 AUXILIARY EQUIPMENT DETAILS .............................................................................................................................. 8 4 TEST FACILITY...................................................................................................................................................... 8 5 GUIDANCE STANDARD .............................................................................................................................................. 9 6 EUT ANTENNA LOCATIONS ..................................................................................................................................... 10 7 RF EXPOSURE .......................................................................................................................................................... 12 7.1 LIMITS ......................................................................................................................................................... 12 7.2 EVALUATION ............................................................................................................................................... 12 8 SPECIFIC ABSORPTION RATE (SAR) ......................................................................................................................... 13 8.1 INTRODUCTION .......................................................................................................................................... 13 8.2 SAR DEFINITION .......................................................................................................................................... 13 9 SAR MEASUREMENTS SYSTEM CONFIGURATION ................................................................................................... 14 9.1 SAR MEASUREMENT SET-UP ....................................................................................................................... 14 9.2 DASY5 E-FIELD PROBE SYSTEM ................................................................................................................... 15 9.3 E-FIELD PROBE CALIBRATION ...................................................................................................................... 16 9.4 OTHER TEST EQUIPMENT ............................................................................................................................ 16 9.5 SCANNING PROCEDURE .............................................................................................................................. 19 9.6 DATA STORAGE AND EVALUATION .............................................................................................................. 21 9.7 TISSUE-EQUIVALENT LIQUID ....................................................................................................................... 23 9.8 SYSTEM CHECK............................................................................................................................................ 24 10 MEASUREMENT PROCEDURES ............................................................................................................................... 26 10.1 GENERAL DESCRIPTION OF TEST PROCEDURES .......................................................................................... 26 10.2 MEASUREMENT VARIABILITY ...................................................................................................................... 26 10.3 TEST COFIGURATION................................................................................................................................... 27 11 TEST RESULTS .......................................................................................................................................................... 31 11.2 SAR TEST RESULTS .........................................…

Text truncated - open the document above for the full version.

Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 1 of 21 APPENDIX A: SYSTEM CHECKING SCANS (0mm) Front face Rear face Left side Right Side Bottom side 6 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 2 of 21 APPENDIX B: SYSTEM CHECKING SCANS Date: 4/26/2023 835 HEAD Communication System: UID 0, CW (0); Frequency: 835 MHz;Duty Cycle: 1:1 Medium: 835 Head Medium parameters used: f = 835 MHz; σ = 0.89 S/m; ε r = 41.5; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: • Probe: EX3DV4 - SN7322; ConvF(9.81, 9.81, 9.81) @ 835 MHz; Calibrated: 2/28/2023 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1473; Calibrated: 2/8/2023 • Phantom: SAM 1 V5.0 (30deg); Type: QD 000 P40 CD; Serial: 1888 • DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Area Scan (7x13x1): Interpolated grid: dx=15 mm, dy=15 mm Maximum value of SAR (interpolated) = 3.23 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 56.41 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 4.01 W/kg SAR(1 g) = 2.58 W/kg; SAR(10 g) = 1.67 W/kg Maximum value of SAR (measured) = 3.51 W/kg Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 3 of 21 Date: 4/25/2023 1750 HEAD Communication System: UID 0, CW (0); Frequency: 1750 MHz;Duty Cycle: 1:1 Medium: 1750 Head Medium parameters used: f = 1750 MHz; σ = 1.38 S/m; ε r = 40.02; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: • Probe: EX3DV4 - SN7322; ConvF(8.36, 8.36, 8.36) @ 1750 MHz; Calibrated: 2/28/2023 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1473; Calibrated: 2/28/2023 • Phantom: SAM 1 V5.0 (30deg); Type: QD 000 P40 CD; Serial: 1888 • DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Area Scan (7x13x1): Interpolated grid: dx=20 mm, dy=20 mm Maximum value of SAR (interpolated) = 9.00 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 87.69 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 15.4 W/kg SAR(1 g) = 8.89 W/kg; SAR(10 g) = 5.02 W/kg Maximum value of SAR (measured) = 13.1 W/kg Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 4 of 21 Date: 4/24/2023 1900 HEAD Communication System: UID 0, CW (0); Frequency: 1900 MHz; Duty Cycle: 1:1 Medium: 1900 Head Medium parameters used: f = 1900 MHz; σ = 1.45 S/m; ε r = 39.75; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: • Probe: EX3DV4 - SN7322; ConvF(8.05, 8.05, 8.05) @ 1900 MHz; Calibrated: 2/28/2023 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1473; Calibrated: 2/28/2023 • Phantom: SAM 1 V5.0 (30deg); Type: QD 000 P40 CD; Serial: 1888 • DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Area Scan (7x9x1): Interpolated grid: dx=12 mm, dy=12 mm Maximum value of SAR (interpolated) = 14.4 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 103.6 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 17.6 W/kg SAR(1 g) = 8.97 W/kg; SAR(10 g) = 4.7 W/kg Maximum value of SAR (measured) = 14.3 W/kg Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 5 of 21 Date: 4/27/2023 2450 HEAD Communication System: UID 0, CW (0); Frequency: 2450 MHz; Duty Cycle: 1:1 Medium: 2450 Head Medium parameters used: f = 2450 MHz; σ = 1.88 S/m; ε r = 37.97; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: • Probe: EX3DV4 - SN7322; ConvF(7.5, 7.5, 7.5) @ 2450 MHz; Calibrated: 2/28/2023 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1473; Calibrated: 2/28/2023 • Phantom: SAM 1 V5.0 (30deg); Type: QD 000 P40 CD; Serial: 1888 • DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Area Scan (7x7x1): Interpolated grid: dx=15 mm, dy=15 mm Maximum value of SAR (interpolated) = 15.1 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 95.32 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 27.9 W/kg SAR(1 g) = 13.3 W/kg; SAR(10 g) = 6.1 W/kg Maximum value of SAR (measured) = 17.5 W/kg Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 6 of 21 Date: 4/28/2028 2600 HEAD Communication System: UID 0, CW (0); Frequency: 2600 MHz; Duty Cycle: 1:1 Medium: 2600 Head Medium parameters used: f = 2600 MHz; σ = 2.02 S/m; ε r = 39.53; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: • Probe: EX3DV4 - SN7322; ConvF(7.3, 7.3, 7.3) @ 2600 MHz; Calibrated: 2/28/2023 • Sensor-Surface: 1.4mm (Mechanical Surface Detection) • Electronics: DAE4 Sn1473; Calibrated: 2/28/2023 • Phantom: SAM 1 V5.0 (30deg); Type: QD 000 P40 CD; Serial: 1888 • DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Area Scan (7x9x1): Interpolated grid: dx=12 mm, dy=12 mm Maximum value of SAR (interpolated) = 18.2 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.25 V/m; Power Drift = -0.14 dB Peak SAR (extrapolated) = 32.3 W/kg SAR(1 g) = 13.9 W/kg; SAR(10 g) = 5.97 W/kg Maximum value of SAR (measured) = 18.8 W/kg Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 1 Page: 7 of 21 APPENDIX C: MEASUREMENT SCANS Date: 4/26/2023 Test Laboratory: Intertek Service GSM850_left Side_CH 128 Communication System: UID 0, GPRS 4slot (0); Frequency: 824.2 MHz;Duty Cycle: 1:2.26464 Medium: 835 Head Medium parameters used (interpolated): f = 824.2 MHz; σ = 0.886 S/m; εr = 42.385; ρ = 1000 kg/m3 Phantom section: Flat Section Ambient Temperature: 22.0 °C; Liquid Temperature: 21.5 °C DASY Configuration: Probe: EX3DV4 - SN7322; ConvF(9.81, 9.81, 9.81) @ 824.2 MHz; Calibrated: 2/28/2023 Sensor-Surface: 1.4mm (Mechanical Surface Detection) Ele…

Text truncated - open the document above for the full version.

Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 1 of 48 APPENDIX E: RELEVANT PAGES FROM PROBE CALIBRATION REPORT(S) Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 2 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 3 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 4 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 5 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 6 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 7 of 48 Test Report Intertek Report No.: 230403080SZN-002_SAR Appendix 2 Page: 8 of…

Text truncated - open the document above for the full version.