2AAOY27212724WANDERBAR PORTABLE SOUNDBAR

• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two con dit ions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. FCC/ IC Radiation Exposure Statement This equipment complies with FCC and IC radiati on exposure limits set forth for an uncontrolled en vir onment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'u tilisateur de l'appareil doit ac cepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." FCC/ IC Déclaration d 'exposition aux rayonnements Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites fixées pour un environnement non contrôlé. Cet appareil doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre co rps. Cet transmett eur ne doit pas être co-situé ou opérant en liaison avec toute autre antenne ou transmetteur. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular inst allation. If this equipment does cause harmful interference to radio or television reception, LIMITED WARRANTY Kuryakyn warrants that an y Kuryakyn products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions: 1. Kuryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s). 2. The product must be properly installed, maintained & operated under normal conditions. 3. Kuryakyn shall not be liable for any consequential & incidental damages, including labor & paint, resulting from failure of a Kuryakyn product, fai lure to deliver, delay in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Kuryakyn & a customer. than int ended. 5. Kuryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’s contained in components of Kuryakyn products will be warranted for defects in materials & workmanship for 3 years from the date of purchase whereas all other components shall be warranted for one (1) year. 6. All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller shall no t carry a Kuryakyn warranty. I f unsure, please contact the place of purchase to verify they are an authorized Kuryakyn reseller. RETURN POLICY Merchandise determined to be defective may be returned up to one year from the date of purchase. Returns must be processed through original seller. Returned merchandise for any other reason other than warranty claims must be in like new condition & subject to a 20% restocking fee. All returns are subject to inspection for determination of full or partial credit. Any returned part that shows evidence of being used or installed contrary to manufacturer’s instructions, &/or subjected to im proper handling, packaging or return shipping by the customer, will not be eligible for exchange, refund or warranty consideration. All returned electrical items will be inspected & tested. If electrical item is deemed functional, no credit will be issued & item will be returned. ©2015 KURYAKYN HOLDINGS, LLC ALL RIGHTS RESERVED KURYAKYN, KURYAKYN K logo and the marks appearing on this instruction sheet are registered and common law trademarks of Kuryakyn Holdings except noted third-party trademarks. A full listing of trademarks and trademark registrations owned by Kuryakyn Holdings can be found at www.kuryakyn.com/legal-notice. Emissions Notice: The California Air Resources Board (CARB) does not permit th e use of aftermarket emission-relat ed parts(s) that alter the performance of OEM emission-related devices unless CARB has issued an Executive Order, other than on racing vehicles on closed courses. Check your local laws and manufacturer’s information. Listed Manufacturers and product model names are for reference only. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any For additional information on third-party product and company names, please consult our Web page at www.kuryakyn.com/legal-notice

Mitek Corp I, the signer, Simon Broadley The differences between the two models are model name and appearance length. They are electrically identical. Item Name ：WANDERBAR PORTABLE SOUNDBAR Model Number: 2721 Additional Model: 2724 FCC ID: 2AAOY27212724 <Signature> Name: Simon Broadley Title: Director of Engineering Company: Mitek Corp

DATE Fed e Auth 7345 Colu On o Houj as o sub m certi defi n labe For i beha for c 6108 <Sig n Nam e Title: Com p E : 2021.01 eral Commu horization & 5 Oakland M umbia, Mary our behalf, I jie, Donggua ur agent in t mitted docum fication is so ned in the Fe l identical to instances w alf, I acknow certification, 89, United St nature> e: Simon Bro Director of pany: Mitek .21 unications C Evaluation D Mills Road land 21046 appoint EST n, Guangdon the preparat ments prope ought. I also ederal Comm o that submit where our au wledge that still resides tates (Applic oadley Engineerin g Corp ommission Division Author i T Technology ng, China (N tion of this a erly describe o certify that munications tted for appr uthorized ag all responsi with Mitek C cant Name a g ity to Act as y Co., Ltd. A ame of Age application fo e the device each unit m s Commissio roval with th ent signs th bility for com Corp Addre and address s Agent Address: Chil nt company or equipmen or system fo manufactured on’s regulatio his applicatio he applicatio mplying with ess: 1 Mitek s) lingxiang, Qi y name and a nt certificatio or which eq d, imported ons will hav on. on for certific h the terms k Plaza Winsl shantou, San address) to on. I certify t uipment or markete d e affixed to cation on ou and conditio ow Illinois ntun, act hat d, as it a ur ons

DATE : 2021.01.21 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AAOY27212724 Product Name: WANDERBAR PORTABLE SOUNDBAR Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Simon Broadley Title: Director of Engineering Company: Mitek Corp

External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721

WANDERBAR PORTABLE SOUNDBAR MODEL:2724 Li-ion Battery 14.8V 3100mA 45.88Wh Adapter Input:100-240V~ 50/60Hz 0.4A Output:6V 2000mA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. FCC ID:2AAOY27212724 IC:22793-27212724CAN ICES-3(B)/NMB-3(B) 15.00 mm 65.00 mm WANDERBAR PORTABLE SOUNDBAR MODEL:2721 Li-ion Battery 14.8V 3100mA 45.88Wh Adapter Input:100-240V~ 50/60Hz 0.4A Output:6V 2000mA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. FCC ID:2AAOY27212724 IC:22793-27212724CAN ICES-3(B)/NMB-3(B) 15.00 mm 65.00 mm

Internal photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721 Bluetooth antenna External photos M/N: 2721 External photos M/N: 2721 External photos M/N: 2721

FCC ID: 2AAOY27212724 EST Technology Co., Ltd Report No. ESTE-R2101079 Page 1 of 3 FCC RF EXPOSURE REPORT Mitek corp WANDERBAR PORTABLE SOUNDBAR Model Number: 2721 Additional Model: 2724 FCC ID: 2AAOY27212724 Prepared for: Mitek Corp 1 Mitek Plaza Winslow IL 61089, United States Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2101079 Date of Test: Jan. 08~18, 2021 Date of Report: Jan. 20, 2021 FCC ID: 2AAOY27212724 EST Technology Co., Ltd Report No. ESTE-R2101079 Page 2 of 3 1. Applicable Standards FCC Part 2(Section 2.1093) FCC KD B447498 D01 General RF Exposure Guidance v06 2. Exposure Evaluation of Portable or Mobile Devices Human exposure to RF emissions from portable devices (47 CFR §2.1093), as defined by the FCC, must be evaluated with respect to the FCC-adopted limits for SAR. Evaluation of mobile devices, as defined by the FCC, may also be performed with respect to SAR limits, but in such cases it is usually simpler and more cost-effective to evaluate compliance with respect to field strength or power density limits. For certain devices that are designed to be used in both mobile and portable configurations similar to those described in 47 CFR §2.1091(d)(4), such as certain desktop phones and wireless modem modules, compliance for mobile configurations is also satisfied when the same device is evaluated for SAR compliance in portable configurations. SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. FCC ID: 2AAOY27212724 EST Technology Co., Ltd Report No. ESTE-R2101079 Page 3 of 3 3. Evaluation Results Worse case is as below: [2402 MHz 0dBm（1mW）output power] (1 mW /5mm) •[√2.402(GHz)]= 0.31 <3.0 for 1-g SAR End of Test Report

FCC ID: 2AAOY27212724 EST Technology Co., Ltd Report No. ESTE-R2101078 Page 1 of 84 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Mitek corp WANDERBAR PORTABLE SOUNDBAR Model Number: 2721 Additional Model: 2724 FCC ID: 2AAOY27212724 Prepared for: Mitek Corp 1 Mitek Plaza Winslow IL 61089, United States Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2101078 Date of Test: Jan. 08~18, 2021 Date of Report: Jan. 20, 2021 FCC ID: 2AAOY27212724 EST Technology Co., Ltd Report No. ESTE-R2101078 Page 2 of 84 TABLE OF CONTENTS Description Page TEST REPORT VERIFICATION......................................................................................................................... 3 1. GENERAL INFORMATION ................................................................................................................. 5 1.1. Description of Device (EUT) ........................................................................................................... 5 1.2. Antenna Information ........................................................................................................................ 5 2. SUMMARY OF TEST ......................................................................................................................... 6 2.1. Summary of test result ...................................................................................................................... 6 2.2. Test Facilities ................................................................................................................................... 7 2.3. Measurement uncertainty ................................................................................................................. 8 2.4. Assistant equipment used for test ..................................................................................................... 8 2.5. Block Diagram ................................................................................................................................. 8 2.6. Test mode ......................................................................................................................................... 9 2.7. Channel List ................................................................................................................................... 10 2.8. Power Setting of Test Software ...................................................................................................... 10 2.9. Test Equipmen ................................................................................................................................ 11 3. MAXIMUM PEAK OUTPUT POWER ................................................................................................. 12 3.1. Limit ............................................................................................................................................... 12 3.2. Test Setup ....................................................................................................................................... 12 3.3. Spectrum Analyzer Setting ............................................................................................................. 12 3.4. Test Procedure ................................................................................................................................ 12 3.5. Test Result ...................................................................................................................................... 13 4. 20 DB BANDWIDTH ....................................................................................................................... 18 4.1. Limit ............................................................................................................................................... 18 4.2. Test Setup ....................................................................................................................................... 18 4.3. Spectrum Analyzer Setting ............................................................................................................. 18 4.4. Test Procedure ................................................................................................................................ 18 4.5. Test Result ...................................................................................................................................... 19 5. CARRIER FREQUENCY SEPARATION .............................................................................................. 24 5.1. Limit ............................................................................................................................................... 24 5.2. Test Setup ....................................................................................................................................... 24 5.3. Spectrum Analyzer Setting ............................................................................................................. 24 5.4. Test Procedure ................................................................................................................................ 24 5.5. Test Result ...................................................................................................................................... 25 6. NUMBER OF HOPPING CHANNEL .................................................................................................. 30 6.1. Limit ............................................................................................................................................... 30 6.2. Test Setup ....................................................................................................................................... 30 6.3. Spectrum Analyzer Setting ............................................................................................................. 30…

Text truncated - open the document above for the full version.

Radiated test: Below 1GHz Radiated test: Above 1GHz Conducted test: