2AB6UAKR1Entry Pad with Bluetooth 4.1

entry pad QSG front and back back front cover Questions? If you have any questions, call 844-AUGUST1 (284-8781) or visit august.com/support ©2015 August Home Inc. 080-00063-01 Getting Started Photo FPO Model: AK-R1 inside spread Install Smart Lock Follow the installation instructions that are included with the Smart Lock to replace your existing thumb-latch. Install Smart Keypad Simply screw the mounting plate on your wall. Remove the plastic battery tab. Easily clip Smart Keypad onto the mounting plate. 1 2 3 1 For detailed installation instructions visit august.com/install Download App On the settings screen in the August app, select “Set Up Smart Keypad” and follow the instructions. Use Smart Keypad Use the August azpp to share entry codes with friends or family. 2 entry pad QSG inside spread Safety Risk of explosion and personal injury if device is installed into non compatible circuit. Do not open, mutilate, or expose to conducting materials (metal), moisture, liquid, fire or heat above 54° C (130° F), incinerate, or immerse in water or liquid of any kind. Do not short circuit. Doing so may cause batteries to leak or explode, resulting in personal injury. The August Doorbell Cam must be correctly installed and used with a wired doorbell circuit that is operating in good condition. You assume all risk associated with the suitability, installation and performance of the door bell and other third party components, hardware, software and services that you select. 4 Terms and Conditions Terms and Conditions Limited Warranty Statement IMPORTANT: By using the August Doorbell Cam hardware (the “Device”) you are agreeing to be bound by the terms of this Limited Warranty set forth below. If you do not agree to the terms of this Limited Warranty you may return the Device (in its original, unused condition) within thirty days of the date of purchase (or the return period provided by your place of purchase, whichever is longer) for a refund in accordance with our returns policy as set forth in Section 3 of this Limited Warranty. This Limited Warranty gives you specific legal rights. You may also have other legal rights that vary by state, province or jurisdiction. The disclaimers, exclusions, and limitations of liability under this Limited Warranty will not apply to the extent prohibited by applicable law. For a full description of your legal rights you should refer to the laws applicable in your jurisdiction and you may wish to contact a relevant consumer advisory service. 1. Duration and Coverage. One (1) year Limited Hardware Warranty. Subject to the additional terms and conditions set forth below, August provides the following Limited Warranty: • Only to the person or entity that originally purchased the Device from August or from one of its authorized resellers or distributors; and • Only for Devices purchased and delivered to the end user within the United States, Canada, or Mexico. 2. Limited Warranty. August warrants the Device against defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase (“Warranty Period”). If a Device is returned to August during the Warranty Period as provided below, and August determines that the Device is defective, August will repair or replace the unit with either a new or a refurbished August Doorbell Cam. If the Warranty Period has expired or is otherwise not applicable as per the Scope and Limitation on Warranty (below), we will return the Device to you. More information about this warranty can be found at www.august.com/support. 3. Return and Warranty Service Process. Please review the online help resources at www.august.com/support prior to seeking warranty service. To obtain warranty service, you must first obtain a Return Merchandise Authorization (RMA) number from a Customer Support Representative (CSR) at August. Customer Support contact information can be found by visiting www.august.com/ support. August may attempt to troubleshoot a warranty-related problem prior to issuing a RMA number. August may ask for additional information upon request. Issued RMA numbers remain valid for thirty days from issuance. Once an RMA number is obtained, your Device must be shipped freight prepaid, together with proof of purchase and all accessories, either in its original packaging or packaging affording an equal degree of protection, to the August authorized distribution facility identified by the CSR. Failure to return any of the accessories may result in a delay and/or result in a credit to August or an invoice for the missing accessories. In performing warranty service, August may furnish replacement parts on an exchange basis and replaced parts will become the property of August. Replacement parts provided by August shall be new or refurbished and of comparable quality, and may be a different part that contains compatible features and functions. You will reimburse August for the inspection, testing and repair of returned equipment determined by August not to be defective or which falls under one of the warranty exclusions described below (as well as pay all shipping and handling charges). In all cases, August’s determination as to whether or not the equipment is defective and covered by warranty will be final. Any replacement equipment will be warranted hereunder for a period of one (1) year from shipment. August reserves the right to change the method by which August may provide warranty service to you, and your Device’s eligibility to receive a particular method of service. 1 Terms and Conditions 4. Scope of and Limitation of Warranty. The warranty on this Device is limited to the repair or replacement of defective Devices as described in the Limited Warranty section above. This warranty does not cover customer training and education, installation, set up or adjustment, signal or reception problems. The August Doorbell Cam (statement about certification or not) must be correctly installed and used with an exi…

Text truncated - open the document above for the full version.

August Home Inc. Date: 2015-08-03 Federal Communications Commission Authorization and Evaluation Division FCC ID: 2AB6UAKR1 ATTESTATION FCC ID: 2AB6UAKR1 Product: AK-R1 Model: AK-R1 We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. Sincerely, _________________ Shannon Petty/ Technical Leader August Home Inc.

657 Bryant St. San Francisco, CA 94107 August Home Inc 657 Bryant St. San Francisco, CA 94107 August 3 rd , 2015 To Whom It May Concern: I Joe Aranda, employee of August Home Inc, hereby authorize Shannon Petty of August Home Inc to sign all regulatory compliance documents. Shannon is a Sr. EE technical leader for August Home Inc. If there any questions please contact me at [email protected]. Sincerely, Joe Aranda

August Home Inc. 665 3rd Street #150, San Francisco, CA 9410 Request of Confidentiality TUV SUD BABT TCB/FCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Pursuant to FCC Sections 0.457 and 0.459 of the Commission’s Rules and IC RSP100 Paragraph 10, we, August Home Inc. hereby requests confidential treatment of information accompanying of following product: Product Name: AK-R1 FCC ID: 2AB6UAKR1 The following information should be held confidential: (1) Operational description (2) Circuit Schematics; (3) Block diagram; ...... The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 DFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices.. We are requesting the commission to grant another 180 days short-term confidentiality request on the following attachments: External Photos Internal Photos Test Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. The Exhibits/Items which are not here are allowed to be published. And also, Pursuant to RSP100 Paragraph 10, we request confidential treatment of information accompanying this application of the following product: August Home Inc. 665 3rd Street #150, San Francisco, CA 9410 Product Name: AK-R1 IC Model No.: AK-R1 IC : 12163A-AKR1 The following information should be held confidential: (1) Operational description (2) Circuit Schematics; (3) Block diagram; ...... The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Exhibits/Items which are not here are allowed to be published. Yours Sincerely, Name: Shannon Petty Sign: Date: 2015-08-03 Email: [email protected] Phone No: 7608282067

EUT Internal Photograph (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo

EUT Internal Photograph (1) EUT Photo (2) EUT Photo

For FCC Standalone SAR test exclusion considerations FCC ID: 2AB6UAKR1 Range F(MHz) 2400-2480 According to KDB 447498 D01 General RF Exposure Guidance v05 4.3.1 Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following, and as illustrated in Appendix B: a) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100 MHz to 1500 MHz b) [Power allowed at numeric threshold for 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) The 1-g and 10-g SAR test exclusion thresholds for below 100 MHz at test separation distances ≤ 50 mm are determined by: a) The power threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm b) The power threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Note: when the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Based on The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm and the formula below: : Band Exposure Condition Pmax Pmax Distance f(GHz) calculation result Stand-alone Test exclusion threshold SAR Test (dBm) (mw) (mm) BT Body -3.19 0.48 5 2.480 0.151 3.00 No Conclusion: 2400MHz-2480MHz SAR was not required.

Test Report FCC Part15 Subpart C Product Name : AK-R1 Model No. : AK-R1 FCC ID : 2AB6UAKR1 IC : 12163A-AKR1 Applicant : August Home, INC. Address : 657 Bryant Street San Francisco, CA 94107 USA Date of Receipt : Jul. 20, 2015 Test Date : Jul. 20, 2015~ Jul. 31, 2015 Issued Date : Aug. 20, 2015 Report No. : 1570499R-RF-US-P06V02 Report Version : V1.2 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of QuieTek Corporation. Report No.: 1570499R-RF-US-P06V02 Page: 2 of 52 Te s t R e p o r t C e r t i f i c a t i o n Issued Date : Aug. 20, 2015 Report No. : 1570499R-RF-US-P06V02 Product Name : AK-R1 Applicant : August Home, INC. Address : 657 Bryant Street San Francisco, CA 94107 USA Manufacturer : August Home, INC. Address : 657 Bryant Street San Francisco, CA 94107 USA Model No. : AK-R1 FCC ID : 2AB6UAKR1 IC : 12163A-AKR1 EUT Voltage : DC: 3.0V Brand Name : August Applicable Standard : FCC CFR Title 47 Part 15 Subpart C: 2014 ANSI C63.4: 2014; ANSI C63.10: 2013 Industry Canada RSS-Gen Issue 4 / RSS-247 Issue 1 Test Result : Complied Performed Location : Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 Documented By : Elaine Wang Senior Engineer Reviewed By : Harry Zhao RF Engineering Manager Approved By : Dream Cao Director Report No.: 1570499R-RF-US-P06V02 Page: 3 of 52 Laboratory Information We, QuieTek Corporation , are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site :http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] LinKou Testing Laboratory : No.5-22, Ruishukeng, Linkou Dist., New Taipei City 24451, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected] Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., SuZhou, China TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : [email protected] Taiwan R.O.C. : BSMI, NCC, TAF USA : FCC Japan : VCCI China : CNAS Report No.: 1570499R-RF-US-P06V02 Page: 4 of 52 TABLE OF CONTENTS Description Page 1. General Information ............................................................................................................. 7 1.1. EUT Description .................................................................................................................. 7 1.2. Mode of Operation ............................................................................................................... 8 1.3. Tested System Details ......................................................................................................... 9 1.4. Configuration of Tested System .......................................................................................... 10 1.5. EUT Exercise Software ...................................................................................................... 11 2. Technical Test.................................................................................................................... 12 2.1. Summary of Test Result ..................................................................................................... 12 2.2. Test Environment............................................................................................................... 14 3. Conducted Emission .......................................................................................................... 15 3.1. Test Equipment ................................................................................................................. 15 3.2. Test Setup ......................................................................................................................... 15 3.3. Limit.................................................................................................................................. 16 3.4. Test Procedure .................................................................................................................. 16 3.5. Uncertainty ........................................................................................................................ 16 3.6. Test Result ........................................................................................................................ 17 4. Radiated Emission ............................................................................................................ 18 4.1. Test Equipment ................................................................................................................. 18 4.2. Test Setup ......................................................................................................................... 19 4.3. Limit.................................................................................................................................. 20 4.4. Test Procedure ......................…

Text truncated - open the document above for the full version.

Test Setup Photograph for Part 15.247/15.407 Description: Radiated Emission Test Setup for Below 30MHz Description: Radiated Emission Test Setup for Below 1GHz Description: Radiated Emission Test Setup for 1~18GHz