2AEU3TSBEAMSensor device with wireless connection

TSD2 USER INSTRUCTIONS 1. INTENDED USE OF TSD2 TSD2 is used for distance measurements and resulting data is sent wirelessly to a Wirepas protocol mesh network. The device has also an accelerometer. Typically TSD2 is used together with MTXH Thingsee Gateway in use cases where distance measurements are performed in several locations and this data is wirelessly collected and sent via 2G cellular connection to a data server / cloud. 2. GENERAL Place two AAA batteries (recommended model Varta Industrial) inside the device, the correct direction is shown on the PWB. Plus sign indicates the positive node of the battery. Snap the B cover in place (please note that the B cover can be placed only in one direction). The device starts making distance measurements about any objects on the top side of the device. Measurements are made once a minute (default, can be changed by configuration). The device starts seeking any other nearby devices having the same pre- programmed Wirepas network ID as the device itself. If it finds any, it connects to this Wirepas network and starts sending measurement results from both sensors to the network once a minute (default, can be changed by configuration). 3. INSTALLATION GUIDELINES The device B cover has a double-sided tape which can be used for attachment; remove the cover tape and attach the device to the desired position for distance measurement. The surface for attachment needs to be flat and clean. Press the device from both sides for 5 seconds to make sure that the tape is correctly attached into the surface. Remove the cover tape from here The device operates with fresh Varta Industrial batteries typically for more than 2 years (this time depends heavily on the configuration used for measurement and reporting intervals). If there is a need to change the batteries, spread the side of the A cover gently as shown in the picture below. Be careful while opening the cover that locking snaps don’t break. Remove the B cover, remove the batteries and place new batteries as described earlier. If the device is already attached to some surface, opening needs to be performed with a special tool: The tool can be ordered from Haltian Products Oy. The device can also be ordered with batteries pre-installed. In this case just pull out the tape disconnecting batteries in order to power on the device. 4. PRECAUTIONS - TSD2 is intended for indoor use only and shall not be exposed to rain. The operating temperature range for the device is -20...+50 °C. - Remove the batteries from the TSD2 device if you are taking it inside an aeroplane (unless you have the pre-installed pull-out tape still in place). The device has a Bluetooth LE receiver/transmitter which must not be operational during a flight. - Please take care that the used batteries are recycled by taking them to appropriate collection point. - When changing batteries, replace both of them at the same time using identical brand and type. - Do not swallow batteries. - Do not throw batteries into water or fire. - Do not short-circuit batteries. - Do not try to charge primary batteries. - Do not open or disassemble batteries. - Batteries should be stored in a dry place and at room temperature. Avoid large temperature changes and direct sunlight. At higher temperature the electrical performance of the batteries may be reduced. - Keep batteries away from children. 5. LEGAL NOTICES Hereby, Haltian Products Oy declares that the radio equipment type TSD2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://thingsee.com Haltian Products Oy vakuuttaa, etta radiolaitetyyppi TSD2 on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://thingsee.com TSD2 operates at Bluetooth® 2.4 GHz frequency band. Maximum radio-frequency power transmitted is +4.0 dBm. Manufacturer name and address: Haltian Products Oy Yrttipellontie 1 D 90230 Oulu Finland FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES FCC Information for the User This product does not contain any user serviceable components and is to be used with approved, internal antennas only. Any product changes of modifications will invalidate all applicable regulatory certifications and approvals. FCC Guidelines for human Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 5 mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Federal Communications Commission Statement This device complies with Part 15 Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods: • Increase the separation between the equipment and the receiver. • Connect the equipment into an electrical outlet on a circuit different from…

Text truncated - open the document above for the full version.

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 30.7.2020 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Agent letter for FCC ID: 2AEU3TSBEAM We, Haltian Products Oy Yrttipellontie 1 D 90230 Oulu, Finland hereby authorize Grant4Com Oy Yrttipellontie 6 90230 Oulu, Finland Mr. Jukka Ollila e-mail: [email protected] Phone: +358405433264 to act as our agent in the preparation of this application for equipment certification, including the signing of all documents relating to these matters. The present authorization considers the development of documents on behalf of the client, written under his own letterhead and related to the necessary information to be provided on his behalf to complete the certification process. We also hereby certify that neither we nor any party to this application are subject to a denial of U.S. Federal benefits, which include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by DEKRA Testing and Certification, S.A.U., still resides with us. This agreement expires one year from the current date. Sincerely, __________________________ By: Jyrki Okkonen Title: CTO, COB Company: Haltian Products Oy Telephone: +358405459870 e-mail: [email protected] DocuSign Envelope ID: 103EC0E4-7C37-4E32-9BFC-B1D9A56FD151

APPLICANT LETTERHEAD FCB012_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 30.7.2020 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Confidentiality request for FCC ID: 2AEU3TSBEAM To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, Haltian Products Oy hereby request requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose: Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Internal Photos Short Term Permanent Operation Description Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term User’s Manual Permanent Confidentiality: The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality: We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short term confidentiality is: 45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date: We are also aware that we are responsible to notify DEKRA in the event information regarding the product or the product is made available to the public. DEKRA will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. DocuSign Envelope ID: 103EC0E4-7C37-4E32-9BFC-B1D9A56FD151 APPLICANT LETTERHEAD FCB012_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Sincerely, __________________________ By: Jyrki Okkonen Title: CTO, COB Company: Haltian Products Oy Telephone: +358405459870 e-mail: [email protected] DocuSign Envelope ID: 103EC0E4-7C37-4E32-9BFC-B1D9A56FD151

TSD2 photos 1 PWB bottom 2 PWB top 3 Product general 4 Product top 5 Product bottom

TSD2 Type label markings for FCC/ISED The markings are done by laser to the device cover

TSD2 photos 1 PWB bottom 2 PWB top 3 Product general 4 Product top 5 Product bottom

Copyright©Verkotan FCC SAR test report_Thingsee Beam_ID4267_01072020.docx SAR Compliance Test Report Date of Report 1/07/2020 Client’s Contact person: Juha Pikkarainen Number of pages: 4 Responsible Test engineer: Kirsi Kyllönen Testing laboratory: Verkotan Oy Elektroniikkatie 17 90590 Oulu Finland Client: Haltian Products Oy Yrttipellontie 1D 90230 Oulu Finland Tested devices Thingsee Beam Related reports: - Testing has been carried out in accordance with: 47CFR §2.1091 Radiofrequency Radiation Exposure Evaluation: Mobile Devices FCC published RF exposure KDB procedures Documentation: The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory Test Results: The DUT complies with the requirements in respect of all parameters subject to the test. The test results relate only to devices specified in this document Date and signatures: 01.07.2020 For the contents: Laboratory Manager Copyright©Verkotan FCC SAR test report_Thingsee Beam_ID4267_01072020.docx TABLE OF CONTENTS 1. SUMMARY OF SAR TEST REPORT ............................................................................................... 4 1.1 TEST DETAILS ........................................................................................................................... 4 1.2 EVALUATION RESULTS ............................................................................................................ 4 2. DESCRIPTION OF THE DEVICE UNDER TEST (DUT) .................................................................... 4 2.1 SUPPORTED FREQUENCY BANDS AND OPERATIONAL MODES ............................................. 4 2.2 TEST EXCLUSIONS ................................................................................................................... 5 3. OUTPUT POWER ............................................................................................................................ 5 3.1 MAXIMUM DEFINED OUTPUT POWER .................................................................................... 5 4. RESULTS.......................................................................................................................................... 5 Copyright©Verkotan FCC SAR test report_Thingsee Beam_ID4267_01072020.docx 1. SUMMARY OF SAR TEST REPORT 1.1 Test Details Device under Test (DUT): Product: Jones sensor Manufacturer: Haltian Products Oy Model: TSD2 Hardware Version: TSD2_02 FCC ID: 2AEU3TSBEAM Document ID: FCC SAR test report_Thingsee Beam_ID4267_01072020.docx 1.2 Evaluation Results The device conforms to the requirements of the standards when the maximum output power is less than or equal to the Test Exclusion Threshold Limit. 2. DESCRIPTION OF THE DEVICE UNDER TEST (DUT) The DUT is a general-purpose sensor device. The device is typically used with 20 cm or larger separation distance of the user. As device is Bluetooth low energy device thus having low output power, the evaluation is done at 5mm separation. Exposure Environment General population, uncontrolled 2.1 Supported Frequency Bands and Operational Modes Bands Modes of Operation Transmitter Frequency Range (MHz) 2.4 Bluetooth low energy 2.402- 2.480 Regulator System Equipment Class Test Exclusion Threshold/ Exemption Limit [mW] Maximum Output Power [mW] Result FCC BLE DTS 10 2.5 PASS Copyright©Verkotan FCC SAR test report_Thingsee Beam_ID4267_01072020.docx 2.2 Test Exclusions FCC SAR test exclusion thresholds in 447498D01 are shown in a table below. 3. OUTPUT POWER 3.1 Maximum defined Output Power Transmission mode Output power [dBm] Output power [mW] BLE 4.0 2.5 4. RESULTS According Appendix A in 447498D01 the SAR test exclusion power threshold for 2450MHz is 10mW at 5mm separation distance. The maximum output power of the DUT is 2.51mW thus it is below the test exclusion threshold.

DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 2020-08-07 Test report No: NIE: 65127RRF.001 Test Report USA FCC Part 15.247, 15.209 CANADA RSS-247, RSS-Gen Radio Frequency Devices. Operation within the bands 902 - 928 MHz, 2400 -2483.5 MHz, and 5725 - 5850 MHz. Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices. General Requirements and Information for the Certification of Radio Apparatus. (*) Identification of item tested Sensor device with Wirepas mesh network connectivity (*) Trademark Thingsee Beam (*) Model and /or type reference TSD2 Other identification of the product HW Version: TSD2_02 SW Version: 2020.04.17.2_ts_tof2 FCC ID: 2AEU3TSBEAM IC: 20236-TSBEAM (*) Features Measurement of distance and acceleration. Wirepas protocol stack using BT LE radio. Applicant HALTIAN PRODUCTS OY Yrttipellontie 1 D, 90230 Oulu, Finland Test method requested, standard USA FCC Part 15.247 (10-1-19 Edition): Operation within the bands 902 - 928 MHz, 2400 -2483.5 MHz, and 5725 - 5850 MHz. USA FCC Part 15.209 (10-1-19 Edition): Radiated emission limits; general requirements. CANADA RSS-247 Issue 2 (February 2017). CANADA RSS-Gen Issue 5 (March 2019). Guidance for Performing Compliance Measurements on Digital Transmission System, Frequency Hopping Spread Spectrum System, and Hybrid Systems Devices Operating Under Section 15.247 of the FCC Rules. 558074 D01 Meas Guidance v05r02 dated April 2, 2019. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. Summary IN COMPLIANCE Approved by (name / position & signature) Jose Carlos Luque RF Lab. Supervisor Date of issue 2020-08-07 Report template No FDT08_22 (*) “Data provided by the client” DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29507456 Report No: (NIE) 65127RRF.001 Page 2 of 38 2020-08-07 Index Competences and guarantees .................................................................................................... 3 General conditions ...................................................................................................................... 3 Uncertainty ................................................................................................................................. 3 Data provided by the client .......................................................................................................... 3 Usage of samples ....................................................................................................................... 4 Test sample description .............................................................................................................. 4 Identification of the client............................................................................................................. 5 Testing period and place ............................................................................................................. 5 Document history ........................................................................................................................ 5 Environmental conditions ............................................................................................................ 6 Remarks and comments ............................................................................................................. 7 Testing verdicts ........................................................................................................................... 8 Summary .................................................................................................................................... 8 Appendix A: Test results. Bluetooth Low Energy ......................................................................... 9 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29507456 Report No: (NIE) 65127RRF.001 Page 3 of 38 2020-08-07 Competences and guarantees DEKRA Testing and Certification S.A.U. is a testing laboratory accredited by the National Accreditation Body (ENAC -Entidad Nacional de Acreditación), to perform the tests indicated in the Certificate No. 51/LE 147. DEKRA Testing and Certification is a FCC-recognized accredited testing laboratory with appropriate scope of accreditation that include testing performed in this test report. DEKRA Testing and Certification is an ISED-recognized accredited testing laboratory with appropriate scope of accreditation that include testing performed in this test report. In order to assure the traceability to other national and international laboratories, DEKRA Testing and Certification S.A.U. has a calibration and maintenance program for its measurement equipment. DEKRA Testing and Certification S.A.U. guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated on the report and, it is based on the knowledge and technical facilities available at DEKRA Testing and Certification S.A.U. at the time of performance of the test. DEKRA Testing and Certification S.A.U. is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA Testing and Certification S.A.U. General conditions 1. This report is only referred to the item that has undergo…

Text truncated - open the document above for the full version.

DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29507456 Report No: (NIE) 65127RRF.001 2020-08-07 Appendix B: Photographs DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 2 of 7 2020-08-07 EQUIPMENT FOR RADIATED MEASUREMENTS DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 3 of 7 2020-08-07 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 4 of 7 2020-08-07 EQUIPMENT FOR CONDUCTED MEASUREMENTS DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 5 of 7 2020-08-07 TEST SETUP FOR RADIATED MEASUREMENTS BELOW 1 GHz DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 6 of 7 2020-08-07 TEST SETUP FOR RADIATED MEASUREMENTS ABOVE 1 GHz DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 65127RRF.001 Page 7 of 7 2020-08-07 TEST SETUP FOR CONDUCTED MEASUREMENTS