2AH7L-MEM1575PowerTag F63 3P 480V

TME52331-00 08/2025 1/6 PowerLogic TM - PowerTag F63 3P 480V IEC/UL - A9MEM1575 en Wireless Communication Energy Sensor fr Capteur d’énergie à communication sans fil de Kabelloser Kommunikationsenergiesensor it Sensore a comunicazione wireless pt Sensor de energia com comunição sem fios zh 无线通讯能量传感器 TME52331-00 www.se.com Refer to the concentrator’s user manual to configure your system. Reportez-vous au manuel d’utilisation du concentrateur pour configurer votre système. Informationen zum Konfigurieren Ihres Systems finden Sie in der Bedienungsanleitung des Datenkonzentrators. Consultare la guida all’uso del concentratore per configurare il sistema. Consulte o manual de utilização do concentrador para configurar o seu sistema. 请参考智能网关模块用 户手册配置 您的系统。 P o w e rT a g A9 F6 3 A9MEM1575 V1.001.001 PP-YY-ww-D- ll-xx xx RF-Id: FF80 0000 RF-Id: FF80 0000 www.se.com/support TME52331 PMD-I/DD/K55/1 - IEC 61557-12 - IEC61010-1 - IEC 61326-1 Table 2 (Industrial environment) - ETSI EN 301 489 This instruction sheet must be kept for further use. PLEASE NOTE bThe installation, maintenance and eventual replacement of this device must only be carried out by a qualified electrician. bThis device must not be repaired. bAll applicable local, regional and national regulations must be complied with during the installation, use, maintenance and replacement of this device. bThis device should not be installed if, when unpacking it, you observe that it is damaged. bSchneider Electric cannot be held responsible in the event of noncompliance with the instructions in this document and in the documents to which it refers. bThe service instruction must be observed throughout the life time of this device. bThe PowerTag devices must be installed inside electrical panels or switchboards, behind a door or plate, so that they are inaccessible to unauthorised persons. bThe electric panels must meet the requirements of the applicable standards (IEC 61439-1) and installed in compliance with current installation and safety rules (IEC 61140). bNo responsability is assumed by Schneider Electric for any consequences arising out of the use of this matérial. La présente instruction de service doit être conservée pour utilisation future. REMARQUE IMPORTANTE bL’installation, l’entretien et le remplacement éventuel de cet appareil doivent être effectués uniquement par un électricien qualifié. bCet appareil ne doit pas être réparé. bToutes les réglementations locales, régionales et nationales applicables doivent être respectées lors de l’installation, l’utilisation, l’entretien et le remplacement de cet appareil. bCet appareil ne doit pas être installé si, lors du déballage, vous observez qu’il est endommagé. bSchneider Electric ne peut être tenu responsable en cas de non-respect des instructions contenues dans ce document et dans les documents auxquels il se réfère. bLes instructions de service doivent être respectées tout au long de la durée de vie de cet appareil. bLes appareils PowerTag doivent être installés à l’intérieur de tableaux ou coffrets électriques, derrière une porte ou un plastron, de telle sorte qu’ils ne soient pas accessibles par une personne non-autorisée. bLes tableaux ou coffrets électriques doivent satisfaire les exigences des normes applicables (CEI 61439-1), et être installés selon les règles d’installation et de sécurité en vigueur (CEI 61140). bSchneider Electric décline toute responsabilité quant aux conséquences de l’utilisation de ce matériel. Heben Sie diese Gebrauchsanleitung für die zukünftige Verwendung auf. BITTE BEACHTEN bDie Installation, die Wartung und der eventuelle Austausch dieses Geräts darf nur von einem qualifizierten Elektriker durchgeführt werden. bDieses Gerät darf nicht repariert werden. bAlle anwendbaren lokalen, regionalen und nationalen Vorschriften müssen eingehalten werden, welche die Installation, den Gebrauch, die Wartung und den Austausch dieses Gerätes betreffen. bDieses Gerät darf nicht installiert werden, wenn Sie beim Auspacken eschädigungen feststellen. bSchneider Electric kann keinesfalls für die Nichtbeachtung der Anweisungen in dieser Anleitung oder Anweisungen in Dokumenten, auf die sie Bezug nimmt, haftbar gemacht werden. bDie Serviceanleitung ist während der gesamten Lebensdauer dieses Gerätes zu beachten. bDer PowerTag muss in elektrischen Verteilungen oder Anlagen immer Verteilungen oder Anlagen immer hinter einer Tür oder Frontplatte installiert werden, um den Zugriff und das Berühren durch nicht qualifizierte Personen zu verhindern. bDie elektrischen Verteilungen oder Schaltanlagen müssen den industriellen Normen entsprechen (IEC 61439-1) und gemäß aktueller Installations- und Sicherheitsrichtlinien (IEC 61140) installiert sein. bSchneider Electric haftet nicht für Schäden, die durch die Verwendung dieses Materials entstehen. Conservare la scheda di istruzioni per uso futuro. NOTA bLe operazioni di installazione, utilizzo, riparazione e manutenzione del presente dispositivo elettrico devono essere eseguite esclusivamente da un elettricista qualificato. bI dispositivi non devono essere riparati. bDurante l’installazione e l’uso del presente dispositivo, è obbligatorio rispettare tutte le normative locali, regionali e nazionali applicabili. bNon installare il dispositivo se durante le operazioni di disimballaggio si nota che è danneggiato. bSchneider Electric non si assume alcuna responsabilità in caso di mancata osservanza delle istruzioni riportate nel presente documento e nei documenti a cui viene fatto riferimento. bNecessario rispettare le istruzioni di servizio per tutta la durata di vita del prodotto. bIl PowerTag deve essere installato in quadri elettrici dove deve essere protetto da uno sportello o una piastra, affinché non vi possa accedere personale non autorizzato. bI quadri devono soddisfare i requisiti delle norme in vigore (IEC 61439-1) ed essere installati in conformità alle norme di sicurezza e di installazione correnti (IEC 61140). bSchneider Elect…

Text truncated - open the document above for the full version.

V01222025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 United States Date: septembre 11, 2025 Ref: Attestation Statement Part 2.911(d)(7) Filing FCC ID: 2AH7L-MEM1575 Schneider Electric Industrie SAS certifies that, as of the dates of this application, Americas Compliance Consulting LLC dba iCertifi “iCertifi” is our designated U.S. agent for service of process for the above referenced FCC ID. Schneider Electric Industrie SAS accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission-related proceeding involving the equipment. iCertifi accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service process for the above referenced FCC ID. Designated U.S. Agent Information: Name Americas Compliance consulting, LLC dba iCertifi FCC FRN 0033399411 Address 2445 NE Division Street, Suite 202 Bend, OR 97703 United States Contact Person Paul Preston Telephone +1-866-885-4575 Email [email protected] Sincerely, Schneider Electric Industrie SAS Americas Compliance Consulting LLC dba iCertifi FRN: 0025527185 0033399411 Contact name S Pavana Paul Preston Title : Deputy General Manager President/CEO Signature

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: November 14, 2025 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AH7L-MEM1575 Schneider Electric Industrie SAS (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Schneider Electric Industrie SAS (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24- 886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Schneider Electric Industrie SAS S Pavana Signature: Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: November 14, 2025 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AH7L-MEM1575 Schneider Electric Industrie SAS (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Link: List of Equipment and Services Covered By Section 2 of The Secure Networks Act Sincerely, Schneider Electric Industrie SAS S Pavana Signature:

Letter of Agency May 5, 2025 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 Timco Engineering, Inc. 13146 NW 86th Drive, Suite 400 Alachua, FL 32615- United States We, the undersigned Schneider Electric Industrie SAS hereby authorizes Majid MOURZAGH, LCIE SUD EST, to act on our behalf in all matters relating to all processes required for FCC certification of our devices. Any and all acts carried out by the above agent on our behalf shall have the same effects as acts of our own. This authorization is valid until: December 31, 2025 If you have any questions regarding this authorization, let us know please. Sincerely, S Pavana Signature:

COVER LETTER Schneider Electric Industrie SAS – A9MEM1575 FCC ID: 2AH7L-MEM1575 M ay 5, 2025 This report concerns: File : Original Grant SubPart: SubPart 15B and 15C Equipment type : PowerTag F63 3P 480V Request issue of grant : __ Immediately upon completion of review ___ Defer grant per 47 CFR 0.457(d)(1)(ii) until ____ date _____. Company Name agrees to notify the Commission by _____date_____ of the intended date of announcement of the product so that the grant can be issued on that date. Confidentiality of grant : __ Applicant requests the existence of this grant to be kept confidential until ____date____. The announcement of this product before this date via freedom of information would be detrimental to Company Name, and therefore must be considered a business secret. Public announcement of this product will not be made prior to this date. (Max. 60 days after grant issued). Limits used : (check one) CISPR 22: ___ ___ Part15: ______ Measurement procedure used is ANSI C63.4-2014 / C63.10-2013 unless another is specified. Other test procedure : ____________________________________________________ Application for verification Prepared by : M ajid MOURZAGH LCIE Sud-Est ZI Centr’Alp – 170, rue de Chatagnon 38430 MOIRANS - France Ph. : 33 4 76 07 36 36 Fax : 33 4 76 55 90 88 e- mail : [email protected] FRN : 0005-0971-18 Applicant for this device S Pavana Schneider Electric Industrie SAS 31 rue Pierre Mendes France 38050 - Grenoble cedex 9 - Ph. : +917760972017 Fax : +33 / e- mail: [email protected] FRN : 0025527185 Signature : Signature : *Not to be filed with Equipment Authorization Branch of FCC unless requested Report format prepared by the Information Technology Industry Council (ITI) ESC-5 and reviewed by FCC staff in 1994

CONFIDENTIALITY REQUEST To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046-1609 Cc : Timco Engineering, Inc. 13146 NW 86th Drive, Suite 400 Alachua, FL 32615- United States May 5, 2025 Subject: Confidentiality request FCC ID: 2AH7L-MEM1575 Sc hneider Electric Industrie SAS requests, pursuant to 47CFR 0.457 and 0.459, post grant confidentiality for portions of the material contained in this application. The following document regarding this submission for FCC ID: 2AH7L-MEM1575 shall be kept confidential: LO NG-TERM CONFIDENTIALITY: 1.Block Diagram description of the equipment(file: Block Diagram - 2AH7L-MEM1575.pdf) 2.Schematic Diagram of the equipment(file: Schematic -2AH7L-MEM1575.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Per manent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. The ap plicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Si ncerely, Re sponsible party: S Pavana Title: General Manager - Certification - Connected Offer Si gnature:

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 1/2 EXTERNAL PHOTOS OF EQUIPMENT FCCID: 2AH7L-MEM1575 LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 2/2

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 1/2 EXTERNAL PHOTOS OF EQUIPMENT FCCID: 2AH7L-MEM1575 LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 2/2

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE Page 1/1 PRODUCT LABELING FCCID: 2AH7L-MEM1575

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 1/3 INTERNAL PHOTOS OF EQUIPMENT FCCID: 2AH7L-MEM1575 LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 2/3 RF ANTENNA LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS – France Page 3/3

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE GENERAL INFORMATION FCCID: 2AH7L-MEM1575 1.1. Product description LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE 1.2. Tested System Details LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE 1.3. Test Methodology Both conducted and radiated testing were performed according to the procedures in ANSI C63.4 or/and ANSI C63.10, FCC Part 15 SubPart 15B and 15C. Radiated testing was performed at an antenna to EUT distance of 10 meters. During testing, all equipment’s and cables were moved relative to each other in order to identify the worst case set-up. 1.4. Test facility Tests have been performed: April 08, 2025 to April 11, 2025 This test facility has been fully described in a report and accepted by FCC as compliant with the radiated and AC line conducted test site criteria in ANSI C63.4 or/and ANSI C63.10. This test facility has also been accredited by COFRAC (French accreditation authority for European Union test lab accreditation organization) according to NF EN ISO/IEC 17025, as compliant with test site criteria and competence in 47 CFR Part 15/ANSI C63.4 and EN55032/CISPR32 norms for 89/336/EEC European EMC Directive application. All pertinent data for this test facility remains unchanged.

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE FCCID: 2AH7L-MEM1575 According to KDB 447498 D01 General RF Exposure Guidance v05 4.3.1 Standalone SAR test exclusion considerations LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Prediction Frequency MHz Conducted Output Power dBm Max Antenna Gain dBi Distance cm Power Density mW/cm2 Limit mW/cm2 2405 5.16 3.27 20 0.0014 1.00 2440 5.25 3.27 20 0.0014 1.00 2480 5.19 3.27 20 0.0014 1.00 Conclusion: Therefore our device complies with FCC’s RF radiation exposure limits for general population without SAR evaluation with at least 20cm separation from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Template : April 2 nd , 2025 Reproduction of this document is only authorized in its complete form. Any partial reproduction or any insertion of results in an accompanying text with a view to their distribution must receive prior and formal agreement from LCIE. This document results from tests carried out on a specimen, sample or test piece. It does not prejudge the conformity of all the products manufactured to the object tested. Unless otherwise indicated or rule specified by the test method, the decision of conformity does not take into account measurement uncertainty. It in no way prejudges a certification decision. The accreditation of the COFRAC Testing Section attests to the technical competence of the laboratories for the tests covered by the accreditation only. If certain tests mentioned in this report were carried out outside the framework of COFRAC accreditation, they are identified by the symbol . LCIE Laboratoire Central des Industries Electriques Une société Bureau Veritas Z.I Centr'alp 170, Rue de Chatagnon 38430 Moirans FRANCE Tél. + 33 4 76 07 36 36 [email protected] www.lcie.fr SAS au capital de 15 745 984€ / RCS Nanterre B 408 363 174 / N° TVA intracommunautaire FR01 408 363 174 / N°SIRET 408 363 174 00017 Accreditation N°1-7429 Scope available on www.cofrac.fr TEST REPORT N°: 25669960-810941-B(FILE#10493812-SRA) Version: 02 Subject Radio spectrum tests according to the standards: FCC CFR 47 PART 15.247 & ANSI C63.10/COR1 + C63.10A RSS-247 & RSS-GEN Issued to Schneider Electric Industrie SAS 31 rue Pierre Mendes France 38050 – GRENOBLE CEDEX 9 FRANCE Apparatus under test  Product PowerTag F63 3P 480V  Trade mark Schneider Electric  Manufacturer Schneider Electric  Family range PowerTag  Model under test A9MEM1575  Serial number EP01 / EP02 / EP03  FCCID 2AH7L-MEM1575  IC 21522-MEM1575 Conclusion See Test Program chapter Test date April 08, 2025 to April 11, 2025 and November 17, 2025 Test location LCIE Grenoble FCC Test site FR0008 - 918017 (MOI) ISED Test site 6500A (MOI) Sample receipt date April 04, 2025 Composition of document 60 pages Document issued on November 19, 2025 Written by : Approved by : Majid MOURZAGH Anthony MERLIN Tests operator Technical manager TEST REPORT N°25669960-810941-B(FILE#10493812-SRA) Version : 02 Page 2/60 PUBLICATION HISTORY Version Date Author Modification 01 November 14, 2025 Majid MOURZAGH Creation of the document 02 November 19, 2025 Majid MOURZAGH Retest OBW measurements on §3 and update using the procedures C63.10-2020 Each new edition of this test report replaces and cancels the previous edition. The control of the old editions of report is under responsibility of client. TEST REPORT N°25669960-810941-B(FILE#10493812-SRA) Version : 02 Page 3/60 SUMMARY 1. TEST PROGRAM ............................................................................................................................. 4 2. EQUIPMENT UNDER TEST: CONFIGURATION (DECLARED BY PROVIDER) .............................. 5 3. OCCUPIED BANDWIDTH ............................................................................................................... 11 4. 6DB BANDWIDTH .......................................................................................................................... 15 5. MAXIMUM CONDUCTED OUTPUT POWER ................................................................................. 19 6. POWER SPECTRAL DENSITY ...................................................................................................... 23 7. UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS ..................................... 27 8. UNWANTED EMISSIONS IN RESTRICTED FREQUENCY BANDS .............................................. 34 9. MEASUREMENT OF CONDUCTED EMISSION ............................................................................ 48 10. UNCERTAINTIES CHART .............................................................................................................. 59 TEST REPORT N°25669960-810941-B(FILE#10493812-SRA) Version : 02 Page 4/60 1. TEST PROGRAM References ➢ 47 CFR Part 15.247 (March, 2025) ➢ RSS 247 Issue 4 ➢ RSS Gen Issue 5 ➢ KDB 558074 D01 DTS Meas Guidance v05r02 ➢ KDB 662911 D01 Multiple Transmitter Output v02r01 ➢ ANSI C63.10-2020/Cor1-2023 + ANSI C63.10a-2024 Radio requirement: Clause - Test Description Test result - Comments Occupied Bandwidth ISED PASS 6dB Bandwidth FCC & ISED PASS Maximum Conducted Output Power FCC & ISED PASS Power Spectral Density FCC & ISED PASS Unwanted Emissions in Non-Restricted Frequency Bands FCC & ISED PASS Unwanted Emissions in Restricted Frequency Bands FCC & ISED PASS Measurement Of Conducted Emission FCC & ISED PASS Receiver Radiated Emissions ISED PASS(2) This table is a summary of test report, see conclusion of each clause of this test report for detail. (1) Limited program (2) Testing covered the receive mode, and receiver spurious emissions are considered to be the same as transmitter. PASS: EUT complies with standard’s requirement FAIL: EUT does not comply with standard’s requirement NA: Not Applicable NP: Test Not Performed TEST REPORT N°25669960-810941-B(FILE#10493812-SRA) Version : 02 Page 5/60 2. EQUIPMENT UNDER TEST: CONFIGURATION (DECLARED BY PROVIDER) 2.1. HARDWARE IDENTIFICATION (EUT AND AUXILIARIES): Equipment under test (EUT): Model under test: A9MEM1575 Serial Number: EP01 / EP02 Dimensions: 6cm x 5cm x 2cm (Length x Width x Height) Type: Table-Top Power supply: Name Type Rating Reference / Sn Comments Supply1 Other : Electrical cabinet 480 VAC LL Imax 63A 50-60Hz - - NC: Not communicated by provider Inputs/outputs - Cable: Access Type Length used (m) Declared <3m Shielded Comments Supply1 480 VAC 2 No No - NC: Not communicated by provider Auxiliary equipment used during test: Type Reference Sn Comments Laptop HP - - Companion device CC2531TI - - NC: Not communicated by provider TEST REPORT N°25669960-810941-B(FILE#10493812-SRA) Version : 02 Page 6/60 Equipment informat…

Text truncated - open the document above for the full version.

OUREA Platform Document type/name Number: Revision: 00 Sheet: 1/6 All information and data contained in this document are the exclusive property of Schneider Electric Industries SAS and may neither be used nor disclosed without its prior written consent Author: 31 January 2024 Status in bold: Draft, In Review, Official Doc. No.: E2-3P Antenna Design Stage Gate OPEN SELECT DO IMPLEMENT PRODUCE SELL CLOSE Status Draft In Review Official Name Department Date Author : Ying Cheng Partner/strategy/EPS 27/8/2014 Reviewer : Emmanuel Dreina This document contains proprietary information of Schneider Electric., and neither the document nor said proprietary information shall be published, reproduced, copied, disclosed or used for any purpose other than consideration of this document without the express written permission of a duly authorized representative of said company. Les informations techniques contenues dans ce document sont la propriété exclusive de SCHNEIDER ELECTRIC SA et ne peuvent être utilisées ou divulguées à des tiers quels qu'ils soient sans son accord écrit. REVISION HISTORY Ver. Date Author(s) Modifications A1 27/8/2014 Ying Cheng Creation A2 OUREA Platform Document type/name Number: Revision: 00 Sheet: 2/6 All information and data contained in this document are the exclusive property of Schneider Electric Industries SAS and may neither be used nor disclosed without its prior written consent Author: 31 January 2024 1 Introduction ............................................................................................................................................ 3 1.1 Simple introduction ......................................................................................................................... 3 1.2 Stack-up of PCB ............................................................................................................................. 3 2 Antenna design...................................................................................................................................... 4 2.1 Material information ........................................................................................................................ 4 2.2 Antenna dimension ........................................................................................................................ 4 2.3 Antenna simulation results ............................................................................................................. 5 2.3.1 Meshing setting ....................................................................................................................... 5 2.3.2 S11 graphic ............................................................................................................................. 5 2.3.3 Radiation Pattern .................................................................................................................... 6 2.3.4 Efficiency ................................................................................................................................. 6 2.3.5 Sweep simulation on S2_X ........................................................... Erreur ! Signet non défini. OUREA Platform Document type/name Number: Revision: 00 Sheet: 3/6 All information and data contained in this document are the exclusive property of Schneider Electric Industries SAS and may neither be used nor disclosed without its prior written consent Author: 31 January 2024 1 INTRODUCTION E2-1P product integrates a zigbee transceiver which is the Atmel’s solution not the TI’s solution. To save cost, it is better to used Printed antenna. 1.1 Simple introduction For E2-3P, brick team already released dimension of antenna in 2013. For the following reasons, I rebuilt simulation (1) Stack-up is changed to 0.26. And I added every prepregs in simulation to see impact from PP. (2) Sensor type is different with previous simulation model based lasted mechanical input from Jean-Yves Amblard Moreover, I used similar slot compared with previous simulation. 1.2 Stack-up of PCB The following stack-up is provided by TPC which is Chinese PCB supplier. It is based B56 file from E square project. OUREA Platform Document type/name Number: Revision: 00 Sheet: 4/6 All information and data contained in this document are the exclusive property of Schneider Electric Industries SAS and may neither be used nor disclosed without its prior written consent Author: 31 January 2024 2 ANTENNA DESIGN 2.1 Material information The properties of material of model will impact simulation results. In this chapter, simulations were done based the following table. List Properties Approx Electric conductivity Or Epsilon Mue substrate FR4 Core:PP2x76288 PP1080 PP7628 4.38 3.87 4.39 1 trace and gnd conductor copper (annealed) 5.8E+07 1 shunt Fe Ni48 FeNi48 1.23E+07 288.52 clip Cu Sn6 CuSn6 5.66E+07 1 Pins Cu Zn30 CuZn30 4.68E+07 1 coil wiring Enameled Copper Copper (annealed) 5.8E+07 1 core bobbin LCP GF30 Plastic part 3.6 1 Current Line N/A copper (annealed) 5.8E+07 1 2.2 Antenna dimension You can know the detail dimension for this antenna. Please notice the mirror relationship between the following figure and brd file. OUREA Platform Document type/name Number: Revision: 00 Sheet: 5/6 All information and data contained in this document are the exclusive property of Schneider Electric Industries SAS and may neither be used nor disclosed without its prior written consent Author: 31 January 2024 2.3 Antenna simulation results 2.3.1 Meshing setting To get accurate simulation results, we use huge meshing to do simulation. 2.3.2 S11 graphic See the following simulation results in the table below. S11-Magnitude Centre frequency: 2.4462Ghz Bandwidth (-6db): about 190MHz -18.26dB @ 2.405Ghz -12.052dB @ 2.45Ghz -8.4088dB@ 2.48Ghz S11-Smith chart OUREA Platform Document type/name Number: Revision: 00 Sheet: 6/6 All information and data contained in this document are the exclusive property of Schneider Electric…

Text truncated - open the document above for the full version.

LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE Page 1/2 CONDUCTED AND RADIATED MEASUREMENT PHOTO FCCID: 2AH7L-MEM1575 1.1 Conducted emission LCIE SUD EST Laboratoire de Moirans Z.I. Centr’Alp 170, Rue de Chatagnon 38430 MOIRANS - FRANCE Page 2/2 1.2 Radiated emissions