2AH7L-PLTDISPPowerLogic Tag Display

11/2020 GDE66712-00 This instruction sheet must be kept for future use. PLEASE NOTE bElectrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. bPowerLogic Tag devices must not be repaired. bPowerLogic Tag devices should not be installed if, while unpacking, any damage is observed. bPowerLogic Tag Display shall be installed so that it is inaccessible to unauthorized persons. bHMI module of PowerLogic Tag Display may be touched by human if panel mounted. bThe electric panels must meet the requirements of the applicable standards and installed in compliance with current installation and safety rules. bThe safety of any system incorporating the equipment is the responsibility of the assembler of the system. bAll relevant local, regional, and national regulations must be respected while installing and using PowerLogic Tag devices. bNo responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. bIf the equipment is used in a manner not specified by manufacturer, the protection provided by equipment may be impaired. La présente instruction de service doit être conservée pour une utilisation future. REMARQUE IMPORTANTE bL’installation, l’utilisation, la réparation et la maintenance des équipements électriques doivent être assurés uniquement par du personnel qualifié. bLes appareils PowerLogic Tag ne doivent pas être réparés. bLes appareils PowerLogic Tag ne doivent pas être installés si vous constatez lors du déballage que ceux-ci sont endommagés. bL’afficheur PowerLogic Tag doit être installé de manière à être inaccessible aux personnes non autorisées. bLe module afficheur du PowerLogic Tag Display peut être touché par l’utilisateur lorsque monté en surface. bLes tableaux ou coffrets électriques doivent satisfaire les exigences des normes applicables et être installés selon les règles d’installation et de sécurité en vigueur. bLa sûreté de tout système intégrant cet équipement est de la responsabilité du concepteur du système. bToutes les réglementations locales, régionales et nationales pertinentes doivent être respectées lors de l’installation et de cet appareil. bSchneider Electric décline toute responsabilité quant aux conséquences de l’utilisation de ce matériel. bSi l’équipement est utilisé d’une manière non spécifiée par le fabricant, la protection apportée par l’équipement peut être réduite. Se recomienda conservar esta guía de servicio para utilizarla en el futuro. TENGA EN CUENTA bLa instalación, manejo, puesta en servicio y mantenimiento de equipos eléctricos deberán ser realizados sólo por personal cualificado. bLos dispositivos PowerLogic Tag no pueden repararse. bSi durante el desembalaje observa que los dispositivos PowerLogic Tag están dañados, no los instale. bPowerLogic Tag Display shall be installed so that it is inaccessible to unauthorized persons. bHMI module of PowerLogic Tag Display may be touched by human if panel mounted. bLas cajas o paneles eléctricos deben cumplir los requisitos de los estándares correspondientes y se deben instalar de acuerdo con las normas de instalación y seguridad actuales. bThe safety of any system incorporating the equipment is the responsibility of the assembler of the system. bDurante la instalación y el uso de los dispositivos PowerLogic Tag, se deben respetar todas las normativas locales, regionales y nacionales correspondientes. bSchneider Electric no se hace responsable de ninguna de las consecuencias del uso de este material. bIf the equipment is used in a manner not specified by manufacturer, the protection provided by equipment may be impaired. www.se.com/us Refer to the concentrator’s user manual to configure your system. Reportez-vous au manuel d’utilisation du concentrateur pour configurer votre système. Consulte el manual de instrucciones del concentrador para configurar su sistema. GDE66712-00 PowerLogic Tag Display - PLTDISP GDE66712 en PowerLogic Tag Display fr Afficheur PowerLogic Tag es Pantella PowerLogic Tag www.se.com/support DANGER / DANGER / PELIGRO HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH bApply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, bThis equipment must only be installed and serviced by qualified electrical personnel. bTurn off all power supplying this equipment before working on or inside equipment. bAlways use a properly rated voltage sensing device to confirm power is off. bThe display and power supply are designed to be used ONLY together. bReplace all devices, doors, and covers before turning on power to this equipment. Failure to follow these instructions will result in death or serious injury. RISQUE DE CHOC ELECTRIQUE, D’EXPLOSION OU D’ARC ELECTRIQUE bPortez un équipement de protection personnelle adapté et respectez les consignes de sécurité électrique courantes. Reportez-vous aux normes NFPA 70E, CSA Z462 ou aux textes équivalents applicables dans votre région du monde. bSeul un personnel qualifié doit effectuer l’installation et l’entretien de cet appareil. bDébranchez toutes les sources d’alimentation de cet équipement avant d’effectuer toute opération interne ou externe sur celui-ci. bUtilisez toujours un dispositif de détection de tension ayant une valeur nominale appropriée pour vous assurer que l’alimentation est coupée. bL’afficheur et son alimentation sont conçus pour fonctionner UNIQUEMENT ensemble. bRemettez en place tous les équipements, les portes et les capots avant de remettre l’appareil sous tension. Le non-respect de ces instructions provoquera la mort ou des blessures graves. RIESGO DE DESCARGA ELÉCTRICA, EXPLOSIÓN O ARCO ELÉCTRICO bUtilice el equipo de protección personal (PPE) adecuado y siga las recomendaciones para el trabajo seguro con dispositivos eléctricos. Consulte NFPA 70E, CSA Z462 la norma local equivalente. bSolo el personal de electricidad cualificado podrá instalar, programar y realizar el mantenimiento del …

Text truncated - open the document above for the full version.

Schneider Electric Industries SAS Date: 2020-06-05 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL-CCIC COMPANY LIMITED to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL-CCIC COMPANY LIMITED on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL-CCIC COMPANY LIMITED as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: Schneider Electric Industries SAS Contact Name: Christophe PRETAVOINE Title of Person: Director for Products Conformity Assessment and Certification Address: Electropole 38EQI 31 avenue Pierre- Mendes France Eybens - F-38050 Grenoble cedex 9 France

Schneider Electric Industries SAS Fede ral Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AH7L-PLTDISP To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: Schneider Electric Industries SAS Contact Name: Christophe PRETAVOINE Title of Person: Director for Products Conformity Assessment and Certification Address: Electropole 38EQI 31 avenue Pierre- Mendes France Eybens - F-38050 Grenoble cedex 9 France Date: 2020-06-05

Schneider Electric Industries SAS DATE : 2020-06-05 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Request for Short-Term Confidentiality Company name: Schneider Electric Industries SAS FCC ID: 2AH7L-PLTDISP FCC Part 15 Certification Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.: (1) Test Setup Photos (2) External Photos (3) I nternal Photos (4) User Ma nual The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Sincerely, Signature Company Name: Schneider Electric Industries SAS Contact Name: Christophe PRETAVOINE Title of Person: Director for Products Conformity Assessment and Certification Address: Electropole 38EQI 31 avenue Pierre- Mendes France Eybens - F-38050 Grenoble cedex 9 France Date: 2020-06-05

Appendix I External Photographs Page 2 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. All View of EUT Page 3 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Top View of EUT Bottom View of EUT Page 4 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Front View of EUT Back View of EUT Page 5 of 5 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Left View of EUT Right View of EUT

Appendix II Internal Photographs Page 2 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Open View of EUT Internal View of EUT-1 Page 3 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Page 4 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-2 Internal View of EUT-3 Page 5 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Page 6 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-4 Internal View of EUT-5 Page 7 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Page 8 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Internal View of EUT-6 Internal View of EUT-7 Page 9 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Page 10 of 10 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. RF Model and Antenna location `

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. This report does not imply that the product(s) has met the criteria for certification. RF EXPOSURE REPORT For PowerLogic Tag Display MODEL NUMBER: PLTDISP PROJECT NUMBER: 4789447349 REPORT NUMBER: 4789447349-2 FCC ID: 2AH7L-PLTDISP ISSUE DATE: May. 15, 2020 Prepared for Schneider Electric Industries SAS Prepared by UL-CCIC COMPANY LIMITED No. 2, Chengwan Road, Suzhou Industrial Park, People’s Republic of China Tel: +86 512-6808 6400 Fax: +86 512-6808 4099 Website: www.ul.com REPORT No.: 4789447349-2 Page 2 of 6 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED.. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 3 2. TEST METHODOLOGY ..................................................................................................... 4 3. FACILITIES AND ACCREDITATION ................................................................................. 4 4. REQUIREMENT ................................................................................................................. 5 REPORT No.: 4789447349-2 Page 3 of 6 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED.. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: Schneider Electric Industries SAS Address: 35 Rue Joseph Monier 92500 Rueil-Malmaison, France Manufacturer Information Company Name: Schneider Electric Industries SAS Address: 35 Rue Joseph Monier 92500 Rueil-Malmaison, France Factory Information Company Name: Enics Electronics (Suzhou) Ltd Address: 7# Building, Xinhang Industrial Park Huangpujiang Rd New & Hi- tech Industrial Development Zone Changshu Suzhou Jiangsu 215500 CHINA EUT Description Product Name PowerLogic Tag Display Model Name PLTDISP Sample Number 3003800 Data of Receipt Sample Apr. 9, 2020 Date Tested Apr. 9, 2020~ May. 13, 2020 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Guidelines for Human Exposure IEEE C95.1 Complies Prepared By: Reviewed By: Jason Yang Tom Tang Engineer Engineer Project Associate Authorized By: Chris Zhong Laboratory Leader REPORT No.: 4789447349-2 Page 4 of 6 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED.. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with KDB 447498 D01 General RF Exposure Guidance v06 and FCC Guidelines for Human Exposure IEEE C95.1. 3. FACILITIES AND ACCREDITATION Accreditation Certificate A2LA (Certificate No.: 4829.01) UL-CCIC COMPANY LIMITED has been assessed and proved to be in compliance with A2LA. FCC (FCC Designation No.: CN1247) UL-CCIC COMPANY LIMITED has been recognized to perform compliance testing on equipment subject to the Commission's Declaration of Conformity (DoC) and Certification rules. IC (IC Designation No.: 25056) UL-CCIC COMPANY LIMITED has been recognized to perform compliance testing on equipment subject to the Commission's Declaration of Conformity (DoC) and Certification rules. Note 1: All tests measurement facilities use to collect the measurement data are located at No. 2, Chengwan Road, Suzhou Industrial Park, Suzhou 215122, People’s Republic of China Note 2: For below 30MHz, lab had performed measurements at test anechoic chamber and comparing to measurements obtained on an open field site. These measurements below 30MHz had been correlated to measurements performed on an OFS. Note 3: The test anechoic chamber in UL-CCIC COMPANY LIMITED had been calibrated and compared to the open field sites and the test anechoic chamber is shown to be equivalent to or worst case from the open field site. REPORT No.: 4789447349-2 Page 5 of 6 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED.. 4. REQUIREMENT LIMIT Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f2)* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/150 30 1500-100,000 -- -- 1.0 30 Note 1: f = frequency in MHz, * means Plane-wave equivalent power density Note 2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. Note 3: The limit value 1.0mW/cm 2 is available for this EUT. MPE CALCULATION METHOD S =PG/(4πR 2 ) where: S = power density (in appropriate units, e.g. mW/ cm2) P = power input to the antenna (in appropriate units, e.g., mW) (the measured power value refer to the tune-up document) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) REPORT No.: 4789447349-2 Page 6 of 6 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED.. CALCULATED RESULTS Radio Frequency Radiation Exposure Evaluation Zigbee (Worst case) Mode Tune-up Power(P) Antenna Gain Power Density Limit Test Result Zigbee (dBm) (mW) (dBi) (Numeric) (mW/cm2) (mW/cm2) -- 5 3.16 2.0 1.58 0.0…

Text truncated - open the document above for the full version.

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. This report does not imply that the product(s) has met the criteria for certification. FCC 47 CFR PART 15 SUBPART C ISED RSS-247 ISSUE 2 CERTIFICATION TEST REPORT For PowerLogic Tag Display MODEL NUMBER: PLTDISP PROJECT NUMBER: 4789447349 REPORT NUMBER: 4789447349-1 FCC ID: 2AH7L-PLTDISP IC ID: 21522-PLTDISP ISSUE DATE: May. 15, 2020 Prepared for Schneider Electric Industries SAS Prepared by UL-CCIC COMPANY LIMITED No. 2, Chengwan Road, Suzhou Industrial Park, People’s Republic of China Tel: +86 512-6808 6400 Fax: +86 512-6808 4099 Website: www.ul.com REPORT No.: 4789447349-1 Page 2 of 72 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Revision History Rev. Issue Date Revisions Revised By V0 05/15/2020 Initial Issue REPORT No.: 4789447349-1 Page 3 of 72 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. CALIBRATION AND UNCERTAINTY ................................................................................ 7 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 7 4.2. MEASUREMENT UNCERTAINTY ............................................................................... 7 5. EQUIPMENT UNDER TEST ............................................................................................... 8 5.1. DESCRIPTION OF EUT .............................................................................................. 8 5.2. MAXIMUM OUTPUT POWER...................................................................................... 9 5.3. CHANNEL LIST ........................................................................................................... 9 5.4. TEST CHANNEL CONFIGURATION ..........................................................................10 5.5. THE WORSE CASE POWER SETTING PARAMETER ..............................................10 5.6. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................11 5.7. TEST ENVIRONMENT ...............................................................................................12 5.8. DESCRIPTION OF TEST SETUP ...............................................................................13 5.9. MEASURING INSTRUMENT AND SOFTWARE USED ..............................................14 6. MEASUREMENT METHODS ............................................................................................15 7. ANTENNA PORT TEST RESULTS ...................................................................................16 7.1. ON TIME AND DUTY CYCLE .....................................................................................16 7.2. 6 dB BANDWIDTH AND 99% OCCUPIED BANDWIDTH ...........................................18 7.3. CONDUCTED OUTPUT POWER ...............................................................................22 7.4. POWER SPECTRAL DENSITY ..................................................................................26 7.5. CONDUCTED BANDEDGE AND SPURIOUS EMISSIONS ........................................30 7.6. RADIATED TEST RESULTS ......................................................................................45 7.6.1. LIMITS AND PROCEDURE .................................................................................45 7.6.2. TEST ENVIRONMENT ........................................................................................50 7.6.3. RESTRICTED BANDEDGE .................................................................................50 7.6.4. SPURIOUS EMISSIONS .....................................................................................55 8. AC POWER LINE CONDUCTED EMISSIONS ..................................................................69 9. ANTENNA REQUIREMENTS ............................................................................................72 REPORT No.: 4789447349-1 Page 4 of 72 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: Schneider Electric Industries SAS Address: 35 Rue Joseph Monier 92500 Rueil-Malmaison, France Manufacturer Information Company Name: Schneider Electric Industries SAS Address: 35 Rue Joseph Monier 92500 Rueil-Malmaison, France Factory Information Company Name: Enics Electronics (Suzhou) Ltd Address: 7# Building, Xinhang Industrial Park Huangpujiang Rd New & Hi- tech Industrial Development Zone Changshu Suzhou Jiangsu 215500 CHINA EUT Description Product Name PowerLogic Tag Display Model Name PLTDISP Sample Number 3003800 Data of Receipt Sample Apr. 9, 2020 Date Tested Apr. 9, 2020~ May. 13, 2020 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C ISED RSS-247 ISSUE 2 PASS PASS REPORT No.: 4789447349-1 Page 5 of 72 UL-CCIC COMPANY LIMITED This report shall not be reproduced except in full, without the written approval of UL-CCIC COMPANY LIMITED. Summary of Test Results Clause Test Items FCC/IC Rules Test Results 1 6dB Bandwidth and 99% Occupied Bandwidth FCC Part 15.247 (a) (2) RSS-247 Clause…

Text truncated - open the document above for the full version.

Appendix III Setup Photographs RADIATED RF MEASUREMENT SETUP (9KHz ~ 30 MHz) RADIATED RF MEASUREMENT SETUP (30MHz ~ 1 GHz) RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz- X axis) RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz- Y axis) RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz- Z axis) POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP