2AJRDIT-30HEADSET

HH-250BHP User Manual Creation Date: July 23, 2020 Revision No: V.1.0 Revision Date: July 23, 2020 1/ MODEL NUMBER: HH-250BHP LEVEL DEPENDENT HEADSET WITH BLUETOOTH Locations of Controls 1. MultiFunction Button 2. Bluetooth Volume Up 3. Bluetooth Volume Down 4. Hunting Volume Up 5. Hunting Volume Down 6. Bluetooth Mic 7. Battery Cover 8. USB Micro Charging Port 9. Charge Indicator Battery Installation Either 3 x AAA sized battery or Tailor Made Lithium Battery can be used. 1. Lithium Battery: - Ensure that the On/Off Knob is switched off. - Open the Battery Cover. Insert the tailor-made Lithium Battery into the battery compartment and plug the battery cord into the Power Connector in correct direction. Close the Battery Cover. - The manufacturer provides the tailor-made Lithium Battery. Other types of Lithium Batteries are not recommended. 2. AAA Sized Batteries: - Turn off the headset. Open the battery cover, insert 3 pieces AAA sized batteries in correct polarity. Close the battery cover. Power On/Off/Pair − Press and hold Multi-Functional button (1) for 2 seconds: Power On − Press and hold Multi-Functional button (1) for 3 seconds: Power Off − 4 hours auto power off Goggle Assist/Siri − Press and hold Multi-Functional button (1) for 1 second: Google Assist/Siri Music − Single Press MultiFunction button (1): Play/Pause − Double Press MultiFunction button (1): Next Track − Triple Press MultiFunction button (1): Previous Track − Press and hold MultiFunction button (1) 1 sec: Siri/Google Assistant (Voice Dial) Bluetooth Pairing Turn on the Bluetooth function on your mobile phone. Search “Apache” and pair. Phone: − Single Press MultiFunction button (1): Answer/End Call − Press and hold the MultiFunction button (1): Reject Call − If two mobiles are connected, the first phone rings, the phones send the own call signal to the headset, single press MultiFunction button (1) to answer the call. While talking with the first caller, the second phone rings (no tones are heard in the headset), you can switch to the second call and put the first call on hold by pressing Multi-Function button (1). Press MultiFunction button (1) to toggle between the first and second callers. Pair with two mobile phones − Pair the first mobile then disconnect the Bluetooth connection with your mobile. Start pairing the second mobile, after paired, activate the first mobile Bluetooth pairing function, the first mobile will automatically establish connection with the headset. − When the first phone rings, the phones send the call signal to the headset, single press Multi-Functional button (1) HH-250BHP User Manual Creation Date: July 23, 2020 Revision No: V.1.0 Revision Date: July 23, 2020 2/ to answer the call. While talking with the first caller, the second phone rings (no tones are heard in the headset), press the Multi-Functional button (1) to switch to the second call and put the first call on hold. Press Multi- Functional button (1) to toggle between the first and second callers. − Allow stream music from one mobile phone only if two devices are paired. Bluetooth Volume: − To adjust the sound level of Bluetooth, Adjusting the volume by pressing button (2) or (3). Hunting − When Power On the headset, the hunting is auto activated with default setting at volume level 7. − Adjust the Hunting volume level by pressing (4) or (5). − Turn off the Hunting feature by pressing (5) to level 0. Charging - Only charge the headset with a maximum 5 voltage charger. Using a charger higher than 5 volts could be dangerous and may damage the headset. - The 1 st voice prompt “Battery is low, please charge” is heard when the battery power falls to 3.3V. Subsequent messages will be prompted in every five minutes, then auto power off after 3 voice prompts. - Insert a USB micro charging cable into the charge port to re-charge the battery. • Charge indicator in red – charging • Charge indicator in green – charging completed Adjusting the Fit 1. Put on the earmuffs with the controls panel over your right ear. 2. With the headband over the crown of your head, position the muffs to completely enclose your ears. The muffs only provide hearing protection when worn with the headband over the crown of your head. 3. Slide the muffs carefully up or down to adjust for a firm, comfortable fit. 4. Ensure the cushions seal tightly against your head with no interference from foreign objects between the ear cup and your head (such as pencils or glasses temple arms). Spread the ear cups only enough to clear the ears. Do not return or reshape the headband. Wearer Information - The earmuffs provides audio signal sound pressure level limitation and limits the entertainment audio signal to 82 dB(A). - These earmuffs are provided with level-dependent attenuation. - To prevent damage to the headset function, do not subject it to rough handling. - The audibility of warning signals at specific workplaces may be impaired while using the entertainment facility. - The wearer should check correct operation before usage. If distortion or failure is detected, the wearer should refer to the manufacturer’s advice for maintenance and replacement of the battery. - This product can use 2-3 years unless the headband/ear cushions or the headset is damaged. Warning - Performance may deteriorate with battery usage. The typical period of continuous use that can be expected from the ear muffs is around 13 hours. - The output of level dependent circuit of this hearing protector may exceed the external sound level. - The output of the electrical audio circuit of this hearing protector may exceed the daily limited sound level. - For best performance, the earmuffs are fitted, adjusted and kept maintenance in accordance to manufacturer’s instruction. - It is important to wear the earmuffs at all times in noisy surroundings to avoid the risk of hearing damage. - Inspect the earmuffs regularly for serviceability. - If the recommendations given above are not adhered, the protection by th…

Text truncated - open the document above for the full version.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Haven Technologies, INC Address 1025 Pine Hill Way, Carmel, Indiana, 46021 USA Grantee Code 2AJRD FCC ID 2AJRDIT-30 Authorized Contact Name Pete Murphy Contact Email [email protected] Contact Phone +1-317-740-0419 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 17-Jun-2020 Print Name: Pete Murphy Title: President *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

 +DYHQ7HFKQRORJLHV,1& 3LQH+LOO:D\ &DUPHO,186$  'DWH
-XQH 72)HGHUDO&RPPXQLFDWLRQ&RPPLVVLRQ (TXLSPHQW$XWKRUL]DWLRQ%UDQFK 2DNODQG0LOOV5RDG &ROXPELD0,'  5HJDUGLQJ
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
3ULQWHG
 3HWH0XUSK\ 7LWOH 3UHVLGHQW 6LJQDWXUH   2QEHKDOIRI&RPSDQ\  7HOHSKRQH   

 +DYHQ7HFKQRORJLHV,1& 3LQH+LOO:D\ &DUPHO,186$   7R6*61RUWK$PHULFD,QF 2OG3HDFKWUHH5RDG 68,7( 6XZDQHH*HRUJLD 8QLWHG6WDWHV  )URP+DYHQ7HFKQRORJLHV,1& +DQFRFN6W &DUPHO,186$  5HJDUGLQJ&RQILGHQWLDOLW\5HTXHVWUHJDUGLQJDSSOLFDWLRQIRU)&&,'
$-5',7  /21*7(50&21),'(17,$/,7< 3XUVXDQWWR&)56HFWLRQDQGRIWKHFRPPLVVLRQ¶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

Appendix A: External Photo of HKEM2006000556AT

FCC label and Label location

Appendix B: Internal Photo of HKEM2006000556AT

Report No.: HKEM200600055602 Page: 1 of 54 Law Man Kit EMC Manager This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request and accessible at http://www.sgs.com/en/Terms-and-conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-conditions.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. T he document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. TEST REPORT Application No.: HKEM2006000556AT Applicant: Haven Technologies, Inc. Address of Applicant: 1025 Pine Hill Way, Carmel, Indiana, 46032, USA Equipment Under Test (EUT): EUT Name: HEADSET Model No.: IT-30, IT-31, IT-32, IT-33, IT-34, IT-35, HH-250B, HH-250BHP Additional Model: Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: 2AJRDIT-30 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2020-07-22 Date of Test: 2020-07-22 to 2020-08-04 Date of Issue: 2020-08-04 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: HKEM200600055602 Page: 2 of 54 Revision Record Version Chapter Date Modifier Remark 01 2020-08-04 Original Authorized for issue by: Leo Xu /Project Engineer Date: 2020-08-04 Law Man Kit /Reviewer Date: 2020-08-04 Report No.: HKEM200600055602 Page: 3 of 54 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Report No.: HKEM200600055602 Page: 4 of 54 Declaration of EUT Family Grouping: Item no.: IT-30, IT-31, IT-32, IT-33, IT-34, IT-35, HH-250B, HH-250BHP According to the confirmation from the applicant, the above models are identical in all electrical aspects in relating to the circuitry design, PCB layout, electrical components used, internal wiring and functions. The differences are only the Model Number, Trade Mark and Brand. Therefore only the model HH-250BHP was tested in this report. Abbreviation: Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radiated Frequency. CH: In this whole report CH means channel. Volt: In this whole report Volt means Voltage. Temp: In this whole report Temp means Temperature. Humid: In this whole report Humid means humidity. Press: In this whole report Press means Pressure. N/A: In this whole report not application. Report No.: HKEM200600055602 Page: 5 of 54 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 5 4 GENERAL INFORMATION .................................................................................................................. 7 4.1 D ETAILS OF E.U.T. ......................................................................................................................... 7 4.2 MODULATION CONFIGURE ............................................................................................................... 9 4.3…

Text truncated - open the document above for the full version.

Report No.: HKEM200600055603 Page: 1 of 10 Law Man Kit EMC Manager This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request and accessible at http://www.sgs.com/en/Terms-and-conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-conditions.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. T he document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. TEST REPORT Application No.: HKEM2006000556AT Applicant: Haven Technologies, Inc. Address of Applicant: 1025 Pine Hill Way, Carmel, Indiana, 46032, USA Equipment Under Test (EUT): EUT Name: HEADSET Model No.: IT-30, IT-31, IT-32, IT-33, IT-34, IT-35, HH-250B, HH-250BHP Additional Model: Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: 2AJRDIT-30 Standard(s) : 47 CFR Part 1.1307, Part 2.1093, KDB 447498 Date of Receipt: 2020-07-22 Date of Test: 2020-07-22 to 2020-08-04 Date of Issue: 2020-08-04 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: HKEM200600055603 Page: 2 of 10 Revision Record Version Chapter Date Modifier Remark 01 2020-08-04 Original Authorized for issue by: Leo Xu /Project Engineer Date: 2020-08-04 Law Man Kit /Reviewer Date: 2020-08-04 Report No.: HKEM200600055603 Page: 3 of 10 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result RF Exposure 47 CFR Part 1.1307, Part 2.1093, KDB 447498 CFR 47 Part 2.1093 CFR 47 Part 2.1093 Pass Declaration of EUT Family Grouping: Item no.: IT-30, IT-31, IT-32, IT-33, IT-34, IT-35, HH-250B, HH-250BHP According to the confirmation from the applicant, the above models are identical in all electrical aspects in relating to the circuitry design, PCB layout, electrical components used, internal wiring and functions. The differences are only the Model Number, Trade Mark and Brand. Therefore only the model HH-250BHP was tested in this report. Abbreviation: Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radiated Frequency. CH: In this whole report CH means channel. Volt: In this whole report Volt means Voltage. Temp: In this whole report Temp means Temperature. Humid: In this whole report Humid means humidity. Press: In this whole report Press means Pressure. N/A: In this whole report not application. Report No.: HKEM200600055603 Page: 4 of 10 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 5 4.1 D ETAILS OF E.U.T. ......................................................................................................................... 5 4.2 MODULATION CONFIGURE ............................................................................................................... 7 4.3 D ESCRIPTION OF SUPPORT UNITS .................................................................................................... 7 4.4 M EASUREMENT UNCERTAINTY ......................................................................................................... 8 4.5 TEST LOCATION ............................................................................................................................. 9 4.6 T EST FACILITY ............................................................................................................................... 9 4.7 DEVIATION FROM STANDARDS ......................................................................................................... 9 4.8 A BNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 9 5 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................10 5.1 RF EXPOSURE ..............................................................................................................................10 5.1.1 Test Requirement: ..................................................................................................................10 5.1.2 Conclusion ..............................................................................................................................10 Report No.: HKEM200600055603 Page: 5 of 10 4 General Information 4.1 Details of E.U.T. Power supply: Adaptor Model: IEC 005 Input: AC 100 V - 240 V, 50/60 Hz, 0.75 A Output: DC 5 V, 1 A or DC 4.5 V ('AAA' size battery x 3) or Rechargeable battery: KBT 602535PL Output: DC 3.7 V Test voltage: AC 120 V C…

Text truncated - open the document above for the full version.

Appendix C: Setup Photo of HKEM2006000556AT Conducted Emissions (150 kHz – 30 MHz) Radiated Emissions (30 MHz – 1 GHz) Radiated Emissions (above 1 GHz) Conducted Emissions