2AKARU1000FU1000F

- 1 - U1000F UHF Integrated Machine User Guide Version: 1.0 Date：2020.03.26 - 2 - Contents 1 Overview ...................................................................................................................................... - 4 - 2 Read Configuration Parameters .................................................................................................. - 4 - 3 Reader Installation ...................................................................................................................... - 5 - - 3 - FCC ID: 2AKARU1000F NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. - 4 - 1 Overview This article mainly introduces the operation method of setting U1000F UHF Integrated Machine DEMO software through USB connection. 2 Read Configuration Parameters 1.Open UHF Reader Demo, click Connect. 2.Click Read Configuration to view the U1000F UHF Integrated Machine configuration parameter information. 3.Refer to the screenshot below for the Demo software interface: 1) The default configuration for the Reader is as follows: Work Mode: Read Always Wiegand Format: Wiegand 26 Power: 26dBm Working Frequency: 902MHz — 928MHz (US) 2) Demo Instructions ➢ Connect the USB port of the USB adapter to the computer and the other end to the Reader. - 5 - ➢ The power adapter is recommended to use DC12V / 3A specification. After the reading head is energized, the buzzer will ring. ➢ Open Demo, click Connect. Display Connection Successful. Indicates that the machine has successfully connected with the Demo. ➢ Output Time: Sets the time interval between adjacent wigan data. ➢ Reader Indicator: Set whether the buzzer will ring when the machine is powered on and the card is brushed. ➢ Work Mode: Set the working mode of the machine, including frequent reading mode, trigger mode, and trigger mode to set the trigger once and how long to read. ➢ RF Settings: Set the RF parameters of the machine, including power, spectrum, and power range of 18-26dbm. ➢ Wiegand Format: Set the output format of the machine wiegand. ➢ Tag Reading Interval: Set the machine read card interval. The card reading interval is the time when the card is read within the card swiping range and the second time when the card is read outside the card swiping range. 3 Reader Installation Refer to the schematic diagram when installing the Reader, install the Reader on the bracket and adjust the Angle according to the actual card swiping effect. Notice： ➢ Please keep away from strong magnetic field when reading head works. ➢ Adjacent readers should not be installed face to face or back. Adjacent readers should be in the RF area of another reader.

[2020-04-23] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Guangdong ZK Radio Electronic Tech co. Ltd FCC ID: 2AKARU1000F To Whom It May Concern: We, Guangdong ZK Radio Electronic Tech co. Ltd hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2AKARU1000F) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2020-04-23). The Limited Agency Agreement expires until further notice, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] Guangdong ZK Radio Electronic Tech co. Ltd Contact person: lixue lan

Apr. 13, 2020 Federal Communication Commission Authorization and Evaluation Division FCC ID: 2AKARU1000F Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1: Block Diagram 2: Schematics 3: Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Guangdong ZK Radio Electronic Tech co. Ltd Contact person: lixue lan

External Photos ALL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID Label Location 60mm*30mm FCC ID:2AKARU1000F This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Internal Photos OPEN VIEW-1 OF EUT OPEN VIEW-1 OF EUT INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT INTERNAL VIEW-7 OF EUT

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description U1000F Model Name U1000F FCC ID 2AKARU1000F 2. EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 3. CALCULATION A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20 cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of § 2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. Antenna Gain=8dBi (Numeric 6.31), π=3.14 Note: 1. Only the worst case recorded. Frequency Output Power Output Power Power Density Power Density Limit MHz dBm mW mW/cm 2 mW/cm 2 920 25.365 343.95 0.432 0.61

Page 1 of 50 FCC Test Report Report No.: AGC00927200301FE03 FCC ID : 2AKARU1000F APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : U1000F BRAND NAME : ZK Radio MODEL NAME : U1000F, UHF1-5F, UHF2-5F, UHF1-10F, UHF2-10F, UHF5F Pro, UHF10F Pro, UR300-10F, UR200-5F, UR200-10F, UR200B-10F, UR300-5F, U1000F, U2000F, UT400-5F, UT400-10F, UR500SF, UR500BF, UR500SF-T, UR500BF-T, UR501SF, UR501BF, UR501SF-T, UR501BF-T, UR502SF, UR502BF, UR502SF-T, UR502BE-T APPLICANT : Guangdong ZK Radio Electronic Tech Co., Ltd DATE OF ISSUE : Apr. 16, 2020 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC00927200301FE03 Page 2 of 50 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr. 16, 2020 Valid Initial Release Report No.: AGC00927200301FE03 Page 3 of 50 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY ............................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................ 6 2.1. PRODUCT DESCRIPTION ..................................................................................................................... 6 2.2. TABLE OF CARRIER FREQUENCYS ..................................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH ............................................................................................................ 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ....................................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ........................................................ 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................. 7 2.7. TEST METHODOLOGY .......................................................................................................................... 7 2.8. SPECIAL ACCESSORIES ....................................................................................................................... 7 2.9. EQUIPMENT MODIFICATIONS .............................................................................................................. 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................. 8 4. DESCRIPTION OF TEST MODES ................................................................................................................. 9 5. SYSTEM TEST CONFIGURATION ............................................................................................................. 10 5.1. CONFIGURATION OF EUT SYSTEM ................................................................................................... 10 5.2. EQUIPMENT USED IN EUT SYSTEM ................................................................................................... 10 5.3. SUMMARY OF TEST RESULTS ............................................................................................................ 10 6. TEST FACILITY ........................................................................................................................................... 11 7. PEAK OUTPUT POWER ............................................................................................................................. 12 7.1. MEASUREMENT PROCEDURE ........................................................................................................... 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT ............................................................................................... 13 8. 20DB BANDWIDTH ..................................................................................................................................... 15 8.1. MEASUREMENT PROCEDURE ........................................................................................................... 15 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................... 15 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................. 15 9. CONDUCTED SPURIOUS EMISSION ........................................................................................................ 17 9.1. MEASUREMENT PROCEDURE ........................................................................................................... 17 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................... 17 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 17 Report No.: AGC00927200301FE03 Page 4 of 50 9.4. LIMITS AND MEASUREMENT RESULT ............................................................................................... 17 10. RADIATED EMISSION ............................................................................................................................... 22 10.1. MEASUREMENT PROCEDURE ......................................................................................................... 22 10.2. TEST SETUP ....................................................................................................................................... 24 10.3. LIMITS AND MEASUREMENT RESULT ............................................................................................. 25 10.4. TEST RESULT .................................…

Text truncated - open the document above for the full version.

Test Setup Photos FCC RADIATED EMISSION TEST SETUP CONDUCTED EMISSION TEST SETUP