2AL8S-0250C03ENetwork Video Recorder

0 V1.03 Wi-Fi Kit Quick Guide 1 1 Default IP, Username and Password IP address: NVR 192.168.1.30 NOTE! For security, you are strongly recommended to set a strong password of at least nine characters including all three elements: digits, letters and special characters. IPC 192.168.1.13 Username: admin Password: 123456 2 Disk Installation The illustrations are for reference only. The actual device may vary. 1. Loosen the screws and remove the cover. 2. Secure the disk by fixing the screws to the screw holes shown in the figure. 3. Connect data cables and power cables to the disk. 4. Put the cover back in place and tighten the screws. 2 3 (Optional) Install SD Card Some camera models support Micro SD card. You need to open the bottom cover to install the SD card. Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the SD card might be damaged. 1. Open the bottom cover. 2. Insert the SD card properly. 4 Connect the Kit The following part shows an example. The actual device may vary. 1. Connect the NVR to a monitor with a VGA or HDMI cable (not included in the kit). 2. Plug a mouse into the USB interface on the NVR. 3. Connect the NVR and the camera to power. Figure 4-1 NVR Interfaces Micro SD slot Audio output USB N etwork interface GND Power supply Antenna interface VGA Antenna interface HDMI IP Network Monitor Monitor E.g.,loudspeaker Mouse 3 Figure 4-2 IPC Interfaces 5 Device Operation 5.1 Startup and Shutdown Make sure the cables are connected correctly and the device is grounded properly. Use a power supply that meets requirements. 5.1.1 Startup Connect the devices to power to start up the devices. 5.1.2 Shutdown Click > Shutdown on the screen toolbar in live view page. CAUTION! Do not disconnect power when the NVR is operating or shutting down. 5.2 Wi-Fi Configuration The camera will get online and start live view on the NVR once the NVR and camera are connected to power. Follow the steps to change Wi-Fi settings. 1. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP. 2. Change settings as needed:  SSID: MAC address by default, you can change as needed. IP Network Network interface Powe r interface Antenna SD card 4  Password: The default is the last eight digits of the serial number. You are strongly recommended to change into a strong password.  Region, Channel: Signal interference varies with region and channel. You are recommended to choose a channel with less signal interference.  Wireless NIC IP: The IP address of wireless NIC. The NVR assigns IP address to connected devices based on the start and end IP address range. CAUTION! The NVR's wireless NIC IP must be in a different network segment with its LAN IP address. 3. Click Apply. NOTE! After SSID or password are changed on the NVR, the new SSID or password will be synchronized to online cameras. For offline cameras, the changed settings cannot be synchronized, and you need to pair the camera with the NVR again. See 5.3 Pair Devices Again for details. 5.3 Pair Devices Again If you change Wi-Fi settings on the NVR when cameras are offline, you need to pair devices again. Choose one of the following methods as needed. 5 NOTE! The following methods are also applicable if you pair a camera not in the kit with the NVR.  One-Click Pair 1. Connect the camera and the NVR to the same switch (or connect the camera to the NVR with a network cable), and connect the devices to power. 2. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP. 3. Press the RESET button on the back of the camera to restore factory default settings. NOTE! The reset button only works in 1-10 minutes after the camera is powered on. If you fails to press the button within the time range, you need to power off the camera and then on again to restore the defaults. 4. Click One-Click Pair. NOTE! This function works within 3 minutes after the camera restores defaults. So, if the camera is not paired successfully within this time, please restart the camera or try other methods. 5. Wait for the camera to get online.  QR Code Pair 1. Connect the camera to power. 2. Press the RESET button on the back of the camera to restore factory default settings. 3. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP. 4. Click QR Code Pair, and follow the on-screen instructions to scan the QR code. 6 5. Wait for the camera to get online.  Use EZView Please refer to 8.5 Pair Camera and NVR for detailed steps. 6 Install Devices 6.1 Wi-Fi Signal Connectivity The antenna sends Wi-Fi signals in all directions around it. Wi-Fi connectivity is the best when antennas are parallel with each other, and is the weakest when the top of an antenna points directly to the top of another. Please arrange the antennas properly to improve Wi-Fi connectivity. Figure 6-1 Installation with Strongest Signal Figure 6-2 Installation with Weakest Signal 6.2 Install the Camera The following part takes wall mount as an example. Make sure the wall is strong 7 enough to support the weight of the camera. Please prepare hardware accessories in advance. 1. Paste positioning stickers on the wall and drill 30mm-depth guide holes using a φ6-6.5mm drill bit. 2. Knock the plastic rivets into the guide holes and ensure that they are tightened up. 3. Screw the locknut to loosen the universal joint, and attach your camera to the wall. 4. Rotate the antenna to the antenna interface in clockwise direction. 5. Adjust the monitoring direction. 6. Connect the camera to power to start up. 7 Playback In the preview page, select the desired window, then right click and select Playback to play the recording of the current day. antenna interface 8 NOTE!  A 7*24 recording schedule is enabled by default. To set a recording schedule manually, right click and select Menu > Storage > Recording and then set recording type and time based on your needs.  If you choose Event type recording, you need to enable the corresponding alarm function and configure alarm-triggered r…

Text truncated - open the document above for the full version.

ZheJiang Uniview Technologies Co.,Ltd. D ate: 2022-04-26 D eclaration Letter about Antenna Use To whom it may concern, WE (ZheJiang Uniview Technologies Co.,Ltd.) HEREBY DECLARED THAT Our product Product Description: Network Video Recorder Model No: NVR301-04LS3-W FCC ID: 2AL8S-0250C03E IC: 25987-0250C03E As below picture shows, this product has two antennas, but the antenna 1 is disabled since it does not have any transmitting functions, only the antenna 2 is used for this product. Name (Printed): Feng Xu Signature: Title: Certification Engineer On behalf of Company: ZheJiang Uniview Technologies Co.,Ltd. Telephone: 18106582562

Applicant Declaration Applicant Declaration Rev: 0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name ZheJiang Uniview Technologies Co.,Ltd. Address 88 Jiangling Road, Binjiang District, Hangzhou 310051 China Grantee Code 2AL8S FCC ID 2AL8S-0250C03E Authorized Contact Name Feng Xu Contact Email [email protected] Contact Phone 18106582562 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applic able rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specifi ed under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certific ation and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has r ead, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title- 47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2022/04/06 Print Name: Feng Xu Title: Certification Engineer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

ZheJiang Uniview Technologies Co.,Ltd. Current Date 2022-04-06 To : SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products *WE ZheJiang Uniview Technologies Co.,Ltd., HEREBY DECLARED THAT Product Description: Network Video Recorder Model No.: NVR301-04LS3-W-NB,NVR301-xxxxLxxxx-yyyyWyyyy-zzz("x" can be 0-9,A-Z,a-z or blank, denoting difference in interface;"y" can be 0-9,A-Z,a-z or blank, denoting performance difference;"z"can be 0-9,A-Z,a-z or blank,denoting target regional; "a" can be 0-9, A or blank, denoting infrared level;"-" is optional) Manufacturer’s Name: ZheJiang Uniview Technologies Co.,Ltd. Manufacturer’s Address: 88 Jiangling Road, Binjiang District, Hangzhou 310051 China *Except that the model number and appearance deviation, are identical with the original product as follows: Note: The definition of identical should be “electrically identical”. A device will be considered to be electrically identical if no changes are made to the devices’ schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical. Model No.: NVR301-04LS3-W Manufacturer’s Name: ZheJiang Uniview Technologies Co.,Ltd. Manufacturer’s Address: 88 Jiangling Road, Binjiang District, Hangzhou 310051 China Sincerely, Signature: Printed Name : Feng Xu Position/Title : Certification Engineer Contact Number: 18106582562

ZheJiang Uniview Technologies Co.,Ltd. Date: 2022-04-06 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AL8S-0250C03E To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with ZheJiang Uniview Technologies Co.,Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Feng Xu Title: Certification Engineer Signature: On behalf of Company: ZheJiang Uniview Technologies Co.,Ltd. Telephone: 18106582562

ZheJiang Uniview Technologies Co.,Ltd. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: ZheJiang Uniview Technologies Co.,Ltd. 88 Jiangling Road, Binjiang District, Hangzhou 310051 China Regarding: Confidentiality Request regarding application for FCC ID : 2AL8S-0250C03E LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code): Feng Xu Title: Certification Engineer Company Name: ZheJiang Uniview Technologies Co.,Ltd.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 4 External Photos Applicant: Zhejiang Uniview Technologies Co., Ltd. Address of Applicant: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Equipment Under Test (EUT): Product Name: Network Video Recorder Model No.: NVR301-04LS3-W Compliance Certification Services (Kunshan) Inc. Page: 2 of 4 Compliance Certification Services (Kunshan) Inc. Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Page: 4 of 4 End

Model: NVR301-04LS3-W Model: NVR301-04LS3-W-NB

Compliance Certification Services (Kunshan) Inc. Page: 1 of 5 Internal Photos Applicant: Zhejiang Uniview Technologies Co., Ltd. Address of Applicant: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Equipment Under Test (EUT): Product Name: Network Video Recorder Model No.: NVR301-04LS3-W Compliance Certification Services (Kunshan) Inc. Page: 2 of 5 Compliance Certification Services (Kunshan) Inc. Page: 3 of 5 Compliance Certification Services (Kunshan) Inc. Page: 4 of 5 Compliance Certification Services (Kunshan) Inc. Page: 5 of 5 End

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Page: 1 of 8 Eric Lin Laboratory Manager 1 Cover Page RF MPE REPORT Application No.: KSCR2203000294AT FCC ID: 2AL8S-0250C03E IC : 25987-0250C03E Applicant: Zhejiang Uniview Technologies Co., Ltd. Address of Applicant: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Manufacturer: Zhejiang Uniview Technologies Co., Ltd. Address of Manufacturer: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Factory: Zhejiang Uniview System Technology Co., Ltd. Address of Factory: No.1277 Qingfeng South Road（South）, Tongxiang Economic Development Zone，Tongxiang City, Jiaxing City, Zhejiang Province Equipment Under Test (EUT): EUT Name: Network Video Recorder Model No.: NVR301-04LS3-W,NVR301-04LS3-W-NB,NVR301-xxxxLxxxx-yyyyWyyyy-zzz("x" can be 0-9,A-Z,a-z or blank, denoting difference in interface;"y" can be 0-9,A-Z,a- z or blank, denoting performance difference;"z"can be 0-9,A-Z,a-z or blank,denoting target regional; "a" can be 0-9, A or blank, denoting infrared level;"-" is optional) ♣ For IC Model No.: NVR301-04LS3-W,NVR301-04LS3-W-NB Standard(s) : FCC Rules 47 CFR §2.1091 KDB447498 D01 General RF Exposure Guidance v06 RSS-102 Issue 5 Amendment 1 (February 2, 2021) Date of Receipt: 2022-03-07 Date of Test: 2022-03-14 to 2022-03-23 Date of Issue: 2022-03-23 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Page: 2 of 8 Revision Record Version Chapter Date Modifier Remark 01 2022-03-23 Original Authorized for issue by: Damon Zhou / Project Engineer Eric Lin / Reviewer Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Page: 3 of 8 2 Contents Page 1 COVER PAGE ................................................................................................................................................. 1 2 CONTENTS ..................................................................................................................................................... 3 3 GENERAL INFORMATION........................................................................................................................... 4 3.1 GENERAL DESCRIPTION OF E.U.T. ......................................................................................................... 4 3.2 TECHNICAL SPECIFICATIONS ................................................................................................................... 4 3.3 TEST LOCATION ....................................................................................................................................... 5 3.4 TEST FACILITY .......................................................................................................................................... 5 4 TEST STANDARDS AND LIMITS ............................................................................................................... 6 4.1 FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS: ......................................................................... 6 4.2 IC RADIOFREQUENCY RADIATION EXPOSURE LIMITS: ............................................................................. 6 5 MEASUREMENT AND CALCULATION .................................................................................................... 7 5.1 MAXIMUM TRANSMIT POWER ................................................................................................................... 7 5.2 MPE CALCULATION ................................................................................................................................. 8 Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Page: 4 of 8 3 General Information 3.1 General Description of E.U.T. Power supply: DC 12V ,2A 3.2 Technical Specifications 2.4GHz Antenna Gain: 4.5dBi (Provided by manufacturer) Antenna Type: Dipole Antenna Channel Spacing: 5MHz Modulation Type: 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g/n: OFDM (64QAM, 16QAM, QPSK, BPSK) Number of Channels: 802.11b/g/n(HT20):11 802.11n(HT40):7 Serial Number: 210235C0E51234567890 Firmware Version: NVR-B3612.1.5.220215 Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Page: 5 of 8 3.3 Test Location All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China. Tel: +86 512 5735 5888 Fax: +86 512 5737 0818 No tests were sub-contracted. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L4354) CNAS has accredited Compliance Certification Services (Kunshan) Inc. to ISO/IEC 17025:2017 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 2541.01) Compliance Certification Services (Kunshan) Inc. is accredited by the American Association for Laboratory Accreditation (A2LA). Certificate No. 2541.01. • FCC (Designation Number: CN1172) Compliance Certification Services Inc. has been recognized as an accredited testing laboratory. Designation Number: CN1172. • ISED (CAB identifier: CN0072) Compliance Certification Services (Kunshan) Inc. has been recognized by Innovation, Science and Economic Development Canada (ISED) as an accredited testing laboratory. Company Number: 2324E • VCCI (Member No.: 1938) The 3m and 10m Semi-anechoic chamber and Shielded Room of Compliance Certification Services (Kunshan) Inc. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-20134, R-11600,C-11707, T-11499, G-10216 respectively. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029402 Pag…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 53 Appendix A for KSCR220300029401 1. Duty Cycle 1.1 Ant1 1.1.1 Test Result Ant1 Mode TX Type Frequency (MHz) T_on (ms) Period (ms) Duty Cycle (%) Duty Cycle Correction Factor (dB) Max. DC Variation (%) 802.11b SISO 2412 100.000 100.000 100.00 0.00 0.00 2437 100.000 100.000 100.00 0.00 0.00 2462 100.000 100.000 100.00 0.00 0.00 802.11g SISO 2412 100.000 100.000 100.00 0.00 0.00 2437 100.000 100.000 100.00 0.00 0.00 2462 100.000 100.000 100.00 0.00 0.00 802.11n (HT20) SISO 2412 100.000 100.000 100.00 0.00 0.00 2437 100.000 100.000 100.00 0.00 0.00 2462 100.000 100.000 100.00 0.00 0.00 802.11n (HT40) SISO 2422 100.000 100.000 100.00 0.00 0.00 2437 100.000 100.000 100.00 0.00 0.00 2452 100.000 100.000 100.00 0.00 0.00 Compliance Certification Services (Kunshan) Inc. Page: 2 of 53 1.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 3 of 53 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 4 of 53 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 5 of 53 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 6 of 53 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 7 of 53 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 8 of 53 2. Bandwidth 2.1 OBW 2.1.1 Test Result Mode TX Type Frequency (MHz) Ant 99% Occupied Bandwidth (MHz) Verdict Result 802.11b SISO 2412 1 15.174 Pass 2437 1 15.184 Pass 2462 1 15.159 Pass 802.11g SISO 2412 1 17.598 Pass 2437 1 17.583 Pass 2462 1 17.572 Pass 802.11n (HT20) SISO 2412 1 18.400 Pass 2437 1 18.389 Pass 2462 1 18.373 Pass 802.11n (HT40) SISO 2422 1 36.211 Pass 2437 1 36.210 Pass 2452 1 36.131 Pass Compliance Certification Services (Kunshan) Inc. Page: 9 of 53 2.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 10 of 53 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 11 of 53 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 12 of 53 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 13 of 53 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 14 of 53 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 15 of 53 2.2 6dB BW 2.2.1 Test Result Mode TX Type Frequency (MHz) Ant 6dB Bandwidth (MHz) Verdict Result Limit 802.11b SISO 2412 1 10.107 >=0.5 Pass 2437 1 10.109 >=0.5 Pass 2462 1 10.105 >=0.5 Pass 802.11g SISO 2412 1 16.591 >=0.5 Pass 2437 1 16.592 >=0.5 Pass 2462 1 16.588 >=0.5 Pass 802.11n (HT20) SISO 2412 1 17.774 >=0.5 Pass 2437 1 17.768 >=0.5 Pass 2462 1 17.761 >=0.5 Pass 802.11n (HT40) SISO 2422 1 36.371 >=0.5 Pass 2437 1 36.355 >=0.5 Pass 2452 1 36.356 >=0.5 Pass Compliance Certification Services (Kunshan) Inc. Page: 16 of 53 2.2.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 17 of 53 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 18 of 53 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 19 of 53 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 20 of 53 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 21 of 53 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 22 of 53 3. Maximum Conducted Output Power 3.1 Power 3.1.1 Test Result Mode TX Type Frequency (MHz) Maximum Average Conducted Output Power (dBm) Verdict Ant1 Limit 802.11b SISO 2412 13.61 <=30 Pass 2437 13.56 <=30 Pass 2462 13.57 <=30 Pass 802.11g SISO 2412 13.23 <=30 Pass 2437 13.17 <=30 Pass 2462 13.20 <=30 Pass 802.11n (HT20) SISO 2412 13.11 <=30 Pass 2437 13.09 <=30 Pass 2462 13.12 <=30 Pass 802.11n (HT40) SISO 2422 13.04 <=30 Pass 2437 13.06 <=30 Pass 2452 13.10 <=30 Pass Note1: Antenna Gain: Ant1: 4.50dBi; Compliance Certification Services (Kunshan) Inc. Page: 23 of 53 3.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 24 of 53 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 25 of 53 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 26 of 53 802.11n(HT20)_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 27 of 53 802.11n(HT20)_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 28 of 53 802.11n(HT40)_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (SISO)_NTNV Compliance Certification Services (Kunshan) Inc. Page: 29 of 53 4. Maximum Power Spectral Density 4.1 PSD 4.1.1 Test Re…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR220300029401 Page: 1 of 82 Eric Lin EMC Laboratory Manager TEST REPORT Application No.: KSCR2203000294AT FCC ID: 2AL8S-0250C03E IC: 25987-0250C03E Applicant: Zhejiang Uniview Technologies Co., Ltd. Address of Applicant: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Manufacturer: Zhejiang Uniview Technologies Co., Ltd. Address of Manufacturer: 88 Jiangling Road, Xixing Town, Binjiang District, Hangzhou City Factory: Zhejiang Uniview System Technology Co., Ltd. Address of Factory: No.1277 Qingfeng South Road（South）, Tongxiang Economic Development Zone，Tongxiang City, Jiaxing City, Zhejiang Province Equipment Under Test (EUT): EUT Name: Network Video Recorder Model No.: NVR301-04LS3-W,NVR301-04LS3-W-NB,NVR301-xxxxLxxxx-yyyyWyyyy- zzz("x" can be 0-9,A-Z,a-z or blank, denoting difference in interface;"y" can be 0- 9,A-Z,a-z or blank, denoting performance difference;"z"can be 0-9,A- Z,a-z or blank,denoting target regional; "a" can be 0-9, A or blank, denoting infrared level;"-" is optional) ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Standard(s) : 47 CFR Part 15, Subpart C 15.247 RSS-247 Issue 2, February 2017 RSS-Gen Issue 5 Amendment 2 (February 2021) Date of Receipt: 2022-03-07 Date of Test: 2022-03-14 to 2022-03-23 Date of Issue: 2022-03-23 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: KSCR220300029401 Compliance Certification Services (Kunshan) Inc. Page: 2 of 82 For IC Model No: NVR301-04LS3-W,NVR301-04LS3-W-NB Report No.: KSCR220300029401 Compliance Certification Services (Kunshan) Inc. Page: 3 of 82 Revision Record Version Chapter Date Modifier Remark 01 2022-03-23 Original Authorized for issue by: Damon_zhou/Project Engineer Eric Lin/Reviewer Report No.: KSCR220300029401 Compliance Certification Services (Kunshan) Inc. Page: 4 of 82 2 Test Summary Radio Spectrum Technical Requirement Item FCC Requirement IC Requirement Method Result Antenna Requirement 47 CFR Part 15, Subpart C 15.203 & 15.247(c) RSS-Gen Cl ause 6.8 N/A Customer Declaration N/A: Not applicable Radio Spectrum Matter Part Item FCC Requirement IC Requirement Method Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.207 RSS-Gen Clause 8.8 ANSI C63.10 (2013) Section 6.2 Pass Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247a(2) RSS-247 Clause 5.2(a) ANSI C63.10 (2013) Section 11.8.1 Pass Conducted Average Output Power 47 CFR Part 15, Subpart C 15.247(b)(3) RSS-247 Clause 5.4(d) ANSI C63.10 (2013) Secti on 11.9.2 Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247(e) RSS-247 Clause 5.2(b) ANSI C63.10 (2013) Section 11.10.2 Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247(d) RSS-247 Clause 5.5 ANSI C63.10 (2013) Section 11.13.3.2 Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247(d) RSS-247 Clause 5.5 ANSI C63.10 (2013) Section 11.11 Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.209 & 15.247(d) RSS…

Text truncated - open the document above for the full version.