2AP35-D303353LED Garage Light

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. ********************************************************************************************** FCC WARNING: NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receive • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4. Restore power to the fuse box and turn the light switch on to activate the fixture. INSTALLATION 1. Carefully remove the utility light from the packaging. Check for any defects or damage. 2. Flush Installation: Screw utility light clockwise into E26 socket to tighten. Adjust fins as desired to direct light where neededThe maximum adjustable angle is 90°. (Figure 1) CAUTION: Before beginning installation turn off the circuit breaker and light switch. NOTE: Be careful not to over-tighten. 3. Recessed Fixture Installation: Add extension adapter (Not Included) as needed. Screw the extension adapter into the E26 socket until tight, then secure the utility light to extension adapter and tighten. (Figure 2) IMPORTANT SAFETY INSTRUCTIONS • Do not use with dimmers. • Not for use in totally enclosed luminaires. • Added weight of the device may cause instability of a free-standing portable luminaire. • This device is not intended for use with emergency exits. • Do not make or alter open holes in an enclosure of wiring or electrical components during kit installation. • The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations. • Suitable for damp location. READ ALL INSTRUCTIONS • LISEZ TOUTES LES INSTRUCTIONS WARNING: Risk of fire or electric shock. LED retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. WARNING: Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does exceed the input rating of the luminaire. WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. • Ne pas utiliser avec des gradateurs. • Ne convient pas à des luminaires totalement fermés. • Le dispositif constitue un poids supplémentaire ce qui peut causer l'instabilité d'un luminaire portatif autonome. • Ne convient pas aux sorties de secours. • Il est interdit de faire ou de modifier une ouverture dans un boîtier de câblage ou de composants électriques au cours de l'installation du nécessaire. • Le nécessaire de modernisation est accepté à titre de composant d'un luminaire lorsque la pertinence de la combinaison doit être déterminée par les autorités compétentes. Ce produit doit être mis en place par un électricien qualifié conformément aux codes électriques appropriés applicables. Le guide d'installation ne supplante pas les réglements locaux ou nationaux en matière d’installations électriques. • Convient aux emplacements humides. AVERTISSEMENT: Risque d'incendie ou de choc électrique. L'installation de ce nécessaire de modernisation exige une personne familière avec la construction et le fonctionnement du système électrique du luminaire et des risques associés. Toute personne qui n’est pas qualifiée ne doit faire qucune tentative,d'installation et doit contacter un électricien qualifié. AVERTISSEMENT: Risque d'incendie ou de choc électrique. N’installer ce nécessaire que dans le luminaire dont les caractéristiques de construction et les dimensions sont conforme à celles illustrées dans les photos et / ou les dessins et dont la puissance d'entrée nominale du nécessaire de modernisation ne dépasse pas celle du luminaire. AVERTISSEMENT: Afin de prévenir l’endommagement ou l’abrasion des câbles, éviter tout contact entre ces derniers et le bord d’un objet tranchant tel qu’une tôle. PROBLEM Light will not come on.A. Light switch is turned off. B. The light is not properly installed. A. Check if the Power switch is set to ON. C. Check if the GFCI has tripped. Check if the 120 Vac circuit breaker has tripped. Reset the GFCI or circuit breaker. POSSIBLE CAUSESOLUTION TROUBLE SHOOTING B. Make sure light is completely screwed into E26 base. C. Fuse is blown or circuit breaker is turned off. T M Model: D303353GQ110 LED Bluetooth® Speaker Utility Light Medium Base Use and Care Guide Read and Save These Instruct…

Text truncated - open the document above for the full version.

INTERNATIONAL DEVELOPMENT COMPANY Agent Authorization Company: INTERNATIONAL DEVELOPMENT COMPANY Address: 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. Product Name: LED Garage Light Model Number(s): D303353GQ110, D303353**### (Where "#" is used to denote numbers or blank for commercial purpose; Where “*” is used to denote letters or blank for commercial purpose) Product Description: LED Garage Light We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022-11-01 Name: zhiquan li Title: Manager Company: INTERNATIONAL DEVELOPMENT COMPANY

October 24, 2022 Declaration Of Identity To Whom It May Concern: With regards to the application for addition Model: D303353**###(Where "#" is used to denote numbers or blank for commercial purpose;Where “*” is used to denote letters or blank for commercial purpose), We declare the hardware circuit and software are identical to the basic model : D303353GQ110. Except the following(s): Model Names, packaging and color. The others are the same. Yours Sincerely, INTERNATIONAL DEVELOPMENT COMPANY Signature:

Date: 24 October 2022 INTERNATIONAL DEVELOPMENT COMPANY To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern: The INTERNATIONAL DEVELOPMENT COMPANY, the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen BALUN Technology Co., Ltd., to act on the behalf of the INTERNATIONAL DEVELOPMENT COMPANY solely in matters relating to the application for an FCC equipment authorization for FCC ID: 2AP35-D303353 including the signing of documents in connection with this Application. Necessary acts carried out by Shenzhen BALUN Technology Co., Ltd. in connection with the Application shall have the same effect as acts of the INTERNATIONAL DEVELOPMENT COMPANY. The INTERNATIONAL DEVELOPMENT COMPANY also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. Section 862. Yours Sincerely, _______ zhiquan li

Date: 24 October 2022 INTERNATIONAL DEVELOPMENT COMPANY To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: INTERNATIONAL DEVELOPMENT COMPANY FCC ID: 2AP35-D303353 FCC Certification Confidentiality Request Gentlemen: This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. INTERNATIONAL DEVELOPMENT COMPANY requests that the following documents regarding this submission for FCC ID: 2AP35-D303353 be kept confidential: Exhibit Type File Name Block Diagram Block Diagram.pdf Schematics Schematics.pdf Operational Description Operational Description.pdf And below exhibit kept short-term confidential (180 days): External photos External photos.pdf Test setup photos test photo.pdf Internal photos Internal photos.pdf User manual User manual.pdf Those documents contain detailed system and equipment description and related information about the product which INTERNATIONAL DEVELOPMENT COMPANY considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, INTERNATIONAL DEVELOPMENT COMPANY considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours Sincerely, zhiquan li

Report No.: BL-SZ22A0088-AW 1 / 3 EUT EXTERNAL PHOTOS FRONT VIEW OF EUT REAR VIEW OF EUT Report No.: BL-SZ22A0088-AW 2 / 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT Report No.: BL-SZ22A0088-AW 3 / 3 TOP VIEW OF EUT BOTTOM VIEW OF EUT

FCC Label and Location FCC Label: Label location:

Report No.: BL-SZ22A0088-AI 1 / 3 EUT INTERNAL PHOTOS EUT UNCOVER VIEW 1 EUT UNCOVER VIEW 2 Report No.: BL-SZ22A0088-AI 2 / 3 MAIN BOARD TOP VIEW MAIN BOARD REAR VIEW PCB Antenna RF Chip Report No.: BL-SZ22A0088-AI 3 / 3 MAIN BOARD TOP VIEW MAIN BOARD REAR VIEW

Report No.: BL-SZ22A0088-701 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 10 Web: www.titcgroup.com Template No.: TRP-FCC-Mobile (2022-08-15) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China TEST REPORT Applicant: INTERNATIONAL DEVELOPMENT COMPANY Address: 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. Equipment Type: LED Garage Light Model Name: D303353GQ110 (refer section 2.4) Brand Name: Great Value FCC ID: 2AP35-D303353 Test Standard: 47 CFR Part 2.1091 (refer section 3.1) Test Date Oct. 09, 2022 - Oct. 11, 2022 Date of Issue: Nov. 01, 2022 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Julie Zhu Checked by: Xu Rui Approved by: Wei Yanquan (Chief Engineer) _______________ _______________ _______________ Report No.: BL-SZ22A0088-701 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 10 Web: www.titcgroup.com Template No.: TRP-FCC-Mobile (2022-08-15) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Revision History Version Issue Date Revisions Content Rev. 01 Nov. 01, 2022 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ......................................................................................................... 3 1.1 Test Laboratory .............................................................................................................. 3 1.2 Test Location .................................................................................................................. 3 2 PRODUCT INFORMATION ......................................................................................................... 4 2.1 Applicant Information ...................................................................................................... 4 2.2 Manufacturer Information ............................................................................................... 4 2.3 Factory Information ........................................................................................................ 4 2.4 General Description for Equipment under Test (EUT) ................................................... 4 2.5 Ancillary Equipment ........................................................................................................ 4 2.6 Technical Information ..................................................................................................... 5 3 SUMMARY OF TEST RESULT ................................................................................................... 6 3.1 Test Standards ............................................................................................................... 6 4 DEVICE CATEGORY AND LEVELS LIMITS .............................................................................. 7 5 ASSESSMENT RESULT ............................................................................................................. 9 5.1 Output Power ................................................................................................................. 9 5.2 Tune-up power ............................................................................................................... 9 5.3 RF Exposure Evaluation Result ..................................................................................... 9 5.4 Conclusion ...................................................................................................................... 9 Report No.: BL-SZ22A0088-701 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 10 Web: www.titcgroup.com Template No.: TRP-FCC-Mobile (2022-08-15) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1 GENERAL INFORMATION 1.1 Test Laboratory Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Test Location Name Shenzhen BALUN Technology Co., Ltd. Location Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1/F, Building B, Ganghongji High-tech Intelligent Industrial Park, No. 1008, Songbai Road, Yangguang Community, Xili Sub-district, Nanshan District, Shenzhen, Guangdong Province, P. R. China Accreditation Certificate The laboratory is a testing organization accredited by FCC as a accredited testing laboratory. The designation number is CN1196. Report No.: BL-SZ22A0088-701 Tel: +86-755-66850100 E-mail: [email protected] Page No. 4 / 10 Web: www.titcgroup.com Template No.: TRP-FCC-Mobile (2022-08-15) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant INTERNATIONAL DEVELOPMENT COMPANY Address 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. 2.2 Manufacturer Information Manufacturer Zhongshan Quanxin Lighting & Electrical Corp., Ltd. Address Zone A, Building 1, No.1, Hongji Road, West District, Zhongshan City, Guangdong Province 2.3 Factory Information Factory Zhongshan Quanxin Lighting & Electrical Corp., Ltd. Address Zone A, Building 1, No.1, Hongji Road, West District, Zhongshan City, Guangdong Province 2.4 General Description for Equipment under Test (EUT) EUT Name LED Garage Light Model Name Under Test D303353GQ110 Series Model Name D303353**### (Where "#" is used to denote numbers or blank for commercial purpose; Where “*” is used to denote letters or blank for commercial purpose) Description of Model name differentiation The hardware circuit and software are identical to the basic model, except the model names, packaging and color. (this information provided by the customer) Hardware Version N/A Software Version N/A Dimensions (Approx.) N/A Weight (Approx.) N/A 2.5 …

Text truncated - open the document above for the full version.

Report No.: BL-SZ22A0088-601 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 66 Web: www.titcgroup.com Template No.: TRP-FCC Part 15.247 (2022-01-12) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China TEST REPORT Applicant: INTERNATIONAL DEVELOPMENT COMPANY Address: 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. Equipment Type: LED Garage Light Model Name: D303353GQ110 (refer section 2.4) Brand Name: Great Value FCC ID: 2AP35-D303353 Test Standard: 47 CFR Part 15 Subpart C (refer section 3.1) Test Date: Oct. 09, 2022 - Oct. 11, 2022 Date of Issue: Nov. 01, 2022 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Julie zhu Checked by: Ye Hongji Approved by: Liao Jianming (Technical Director) _______________ _______________ _______________ Report No.: BL-SZ22A0088-601 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 66 Web: www.titcgroup.com Template No.: TRP-FCC Part 15.247 (2022-01-12) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Revision History Version Issue Date Revisions Rev. 01 Nov. 01, 2022 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ......................................................................................................... 4 1.1 Test Laboratory .............................................................................................................. 4 1.2 Test Location .................................................................................................................. 4 2 PRODUCT INFORMATION ......................................................................................................... 5 2.1 Applicant Information ...................................................................................................... 5 2.2 Manufacturer Information ............................................................................................... 5 2.3 Factory Information ........................................................................................................ 5 2.4 General Description for Equipment under Test (EUT) ................................................... 5 2.5 Technical Information ..................................................................................................... 6 3 SUMMARY OF TEST RESULTS ................................................................................................. 8 3.1 Test Standards ............................................................................................................... 8 3.2 Test Verdict .................................................................................................................... 8 4 GENERAL TEST CONFIGURATIONS ........................................................................................ 9 4.1 Test Environments ......................................................................................................... 9 4.2 Test Equipment List ........................................................................................................ 9 4.3 Test Software List ........................................................................................................... 9 4.4 Measurement Uncertainty ............................................................................................ 10 4.5 Description of Test Setup ............................................................................................. 10 4.6 Measurement Results Explanation Example ................................................................ 13 5 TEST ITEMS .............................................................................................................................. 14 5.1 Antenna Requirements ................................................................................................. 14 5.2 Frequency Hopping Systems ....................................................................................... 15 5.3 Number of Hopping Frequencies ................................................................................. 17 5.4 Peak Output Power ...................................................................................................... 18 Report No.: BL-SZ22A0088-601 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 66 Web: www.titcgroup.com Template No.: TRP-FCC Part 15.247 (2022-01-12) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 5.5 Occupied Bandwidth .................................................................................................... 19 5.6 Carrier Frequency Separation ...................................................................................... 20 5.7 Time of Occupancy (Dwell time) .................................................................................. 21 5.8 Conducted Spurious Emission & Authorized-band band-edge .................................... 23 5.9 Conducted Emission .................................................................................................... 24 5.10 Radiated Spurious Emission ........................................................................................ 25 5.11 Band Edge (Restricted-band band-edge) ..................................................................... 27 ANNEX A TEST RESULT ............................................................................................................. 28 A.1 Number of Hopping Frequency .................................................................................... 28 A.2 Peak Output Power ...................................................................................................... 29 A.3 20 dB and 99% bandwidth ........................................................................................... 31 A.4 Hopping Frequency Separation ............................…

Text truncated - open the document above for the full version.

Report No.: BL-SZ22A0088-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China TEST REPORT Applicant: INTERNATIONAL DEVELOPMENT COMPANY Address: 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. Equipment Type: LED Garage Light Model Name: D303353GQ110 (refer section 2.4) Brand Name: Great Value Test Standard: ANSI/IEEE Std 149-1979 Test Date: Oct. 12, 2022 Date of Issue: Nov. 01, 2022 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Mai Jintian Checked by: Tolan Tu Approved by: Wei Yanquan (Chief Engineer) _______________ _______________ _______________ Report No.: BL-SZ22A0088-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Revision History Version Issue Date Revisions Rev. 01 Nov. 01, 2022 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ......................................................................................................... 3 1.1 Test Laboratory ..................................................................................................................... 3 1.2 Test Location ......................................................................................................................... 3 2 PRODUCT INFORMATION ......................................................................................................... 4 2.1 Applicant Information ............................................................................................................ 4 2.2 Manufacturer Information ...................................................................................................... 4 2.3 General Description for Equipment under Test (EUT) .......................................................... 4 2.4 Ancillary Equipment .............................................................................................................. 4 2.5 Technical Information ............................................................................................................ 4 3 SUMMARY OF TEST RESULTS ................................................................................................. 5 3.1 Test Standards ...................................................................................................................... 5 3.2 Test Verdict ........................................................................................................................... 5 3.3 Test Uncertainty .................................................................................................................... 5 4 GENERAL TEST CONFIGURATIONS ........................................................................................ 6 4.1 Test Condition ....................................................................................................................... 6 4.2 Test Equipment List .............................................................................................................. 6 4.3 Test Setup ............................................................................................................................. 7 ANNEX A TEST RESULTS ............................................................................................................. 8 A.1 Gain and Efficiency ............................................................................................................... 8 ANNEX B RADIATION PATTERN .................................................................................................. 9 ANNEX C TEST SETUP PHOTOS ............................................................................................... 12 ANNEX D EUT PHOTO ................................................................................................................ 12 Report No.: BL-SZ22A0088-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1 GENERAL INFORMATION 1.1 Test Laboratory Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Test Location Name Shenzhen BALUN Technology Co., Ltd. Location Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 1/F, Building B, Ganghongji High-tech Intelligent Industrial Park, No. 1008, Songbai Road, Yangguang Community, Xili Sub-district, Nanshan District, Shenzhen, Guangdong Province, P. R. China Report No.: BL-SZ22A0088-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 4 / 13 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: Block B, 1/F, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant INTERNATIONAL DEVELOPMENT COMPANY Address 899 Henrietta Creek Road, Roanoke, Texas 76262 USA. 2.2 Manufacturer Information Manufacturer Zhongshan Quanxin Lighting & Electrical Corp., Ltd. Address Zone A, Building 1, No.1, Hongji Road, West District, Zhongshan City, Guangdong Province 2.3 General Description for Equipment under Test (EUT) EUT Name LED Garage Light Model Name Under Test D303353GQ110 Series Model Name D303353**### (Where "#" is used to denote numbers or blank for commercial purpose; Where “*” is used to denote letters or blank for commercial purpose) Description of Model name differentiation The hardwa…

Text truncated - open the document above for the full version.

Report No.: BL-SZ22A0088-AA 1 / 1 EUT PHOTO Antenna

Report No.: BL-SZ22A0088-AO 1 / 1 TEST SETUP PHOTOS

Report No.: BL-SZ22A0088-AR 1 / 4 TEST SETUP PHOTOS 1 Radiated Test Photo Below 30MHz 30MHz-1GHz Report No.: BL-SZ22A0088-AR 2 / 4 Close-up Above 1GHz Report No.: BL-SZ22A0088-AR 3 / 4 Close-up 2 Conducted Test Photo Conducted Test-BT Report No.: BL-SZ22A0088-AR 4 / 4 3 Conducted Emission