2AUCU-141U1WWI-FI SWITCH SINGLE POLE

™ DANGER / PELIGRO / DANGER -- - - GDE7797800-00 SQR141U1**W Wi-Fi® Switch, Energy Monitoring Interruptor Wi-Fi® SQR141U1**W Interrupteur Wi-Fi® SQR141U1**W seuqitsirétcaraCsacitsíretcaraCserutaeF • Manual and Remote ON/OFF control of any connected lighting and other electrical load • Can be used for single pole or 3-Way (Multi-location) with rocker switch • You can Turns your devices on or off at any time or anywhere have Internet using the free SE Wiser App on your smartphone • Wi-Fi® is a registered trademark of Wi-Fi Alliance R FCC ID: 2AUCU-141U1W IC: 25381-141U1W WARNING / ADVERTENCIA / AVERTISSEMENT HAZARD OF HEAT AND FIRE DAMAGE Read all instructions before installation. The manufacturer will not be held responsible for product damage resulting from not following the instructions. • Wet hands are strictly prohibited. • Work strictly according to the rated load. • Do not continue working after self-disassembly of any nature and damage of external forces. PELIGRO DE DAÑO POR CALENTAMIENTO E INCENDIO Lea todas las instrucciones antes de la instalación. El fabricante no será responsable por los daños causados al producto por no seguir las instrucciones. • Está estrictamente prohibido tener las manos m ojadas. • Trabajar estrictamente de acuerdo con la carga nominal. • No siga trabajando si se produce un desmontaje de cualquier naturaleza, o daño por fuerzas externas. RISQUE DE DOMMAGE CAUSÉ PAR LA CHALEUR ET LE FEU Lisez toutes les instructions avant l’installation. Le fabricant ne pourra pas être tenu responsable des dégâts causés au produit qui peuvent survenir si ces instructions ne sont pas respectées. • Il est strictement interdit de l’utiliser avec les mains mouillées. • Travaillez en respectant strictement la charge nominale! • Arrêtez de travailler après une désintégration accidentelle de quelque nature que ce soit et des dommages causés par des forces extérieures. Failure to follow these instructions can result in death, serious injury, or equipment damage. El incumplimiento de estas instrucciones puede causar la muerte, lesiones serias o daño al equipo. Si ces directives ne sont pas respectées, cela peut entraîner la mort, des blessures graves ou des dommages matériels. noitallatsnInóicalatsnInoitallatsnI 1. Turn the power OFF at circuit breaker or fuse and test that power is off, using a properly rated voltage sensing device, before wiring. 1. Desconecte la alimentación en el interruptor automático o fusible y, antes de realizar el cableado, compruebe que la alimentación esté desconectada usando un dispositivo detector de voltaje nominal adecuado. 1. Avant de procéder au raccordement, coupez le courant au niveau du disjoncteur ou du fusible et vérifiez que l’alimentation est bien coupée à l’aide d’un dispositif de détection de tension correctement calibré. etcenoC.2.margaid gniriw eht ot gnidrocca ecived eht eriW.2los cables al dispositivo según el diagrama de cableado correspondiente. 2. Câblez l’appareil conformément au schéma de câblage. 3. Check that all connections are tight and no bare wires exposed.3. Verifique que todas las conexiones estén apretadas y no haya cables desnudos expuestos. 3. Vérifiez que tous les raccordements sont bien serrés et qu’aucun fil dénudé n’est à découvert. 4. Install the receptacle into the standard outlet box using the screws provided. 4. Instale el receptáculo en la caja del tomacorriente estándar usando los tornillos provistos. 4. Installez la prise dans le boîtier de prise standard à l’aide des vis fournies. Voltage / Tensión / Tension120 Vac, 60 Hz / 120 Vca, 60 Hz / 120 V CA, 60 Hz Incandescent lights / Luces incandescentW 0001ecnecsednacni à stnayoV / se LED lights / Luces LED / Voyants DEL5 A Standard Ballast / Balasto estándar / Ballast standard1200 Va / 1200 Va / 1 200 VA Resistive load / Carga resistiva / Charge résistive1800 W (15 A) Motor / Motor / Moteur1/2 Hp Operating Temperature / Temperatura de operación / Température de C a 40 ºC) / 32 à 104 °F (0 à 40 °C)º 0 ed( Fº 401 a Fº 23 eD / )C°04–0( F°401–23tneme nnoitcnof Supply Connection / Conexión de alimentac GWA 41noitatnemila'l à tnemedroccaR / nói 1 Wireless Type / Tipo inalámbrico / Type sans filWi-Fi®, IEEE 802.11b/g/n Wireless Frequency / Frecuencia inalámbrica / SQR141U1**W Specifications / Especificaciones / Caractéristiques 2.4 GHz SQR141U1**W Wi-Fi® Switch Interruptor Wi-Fi® SQR141U1**W Interrupteur Wi-Fi® SQR141U1**W GDE7797800-00 Figure / Figura / Figure 3 :Wall Plates / Placas de pared / Plaques murales Figure / Figura / Figure 1 : Single-Pole Wiring Diagram / Diagrama de cableado unipolar / Schéma de câblage unipolaire Figure / Figura / Figure 2 : .)esulcni non( elarum euqalp al zellatsnI.5.)adiulcni on( derap ed acalp al elatsnI.5.)dedulcni ton( etalp llaw eht llatsnI.5 .noitatnemila’l zessilbatéR.6.nóicatnemila al eruatseR.6.rewop erotseR.6 LOAD / CARGA / CHARGE H N G L L G N Outlet Box / Caja de tomacorriente / Boîte de sortie G G Wire connector / Conector de conductores / Capuchon de connexion LOAD HOT TRAVELER NEUTRAL H Hot / Fase / Actif N Neutral / Neutro / Neutre G Ground / Tierra / Terre LLoad / Carga / Charge Back wire / Conductor posterior / Fil arrière About wire connections: / Sobre conexiones del cable: / À propos de connexions de fils : 0.5 in (12.7 mm) / 0.5 pulgadas (12.7 mm) / 0,5 po (12,7 mm) Max. torque: 14 lbs-in / Par apriete máx: 14 lbs-pulg / Couple de serrage max : 14 lb-po SQWVS14101**W SQWVM14101**W X Series / Serie X / Série X XD Series / Serie XD / Série XD XD Series Multigang / Interruptor múltiple Serie XD / Séries XD multiprise Only for installation of XD series cover plate. / Solo para la instalación de la placa de cubierta de la serie XD. / Uniquement pour l’installation du couvercle de la série XD. ** = color code / código de color / code de couleur : WH (white / blanco / blanc) LA (light almond / marfil / vert amande clair) BK (black / negro / noir) GY (gray / gris / gris) LOAD HOT NEUTRAL TRAVELER Made in China STRIP GAUGE…

Text truncated - open the document above for the full version.

Schneider Electric (China) Co., Ltd., Shenzhen Branch Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Confirmation Letter We, Schneider Electric (China) Co., Ltd., Shenzhen Branch The product: WI-FI SWITCH SINGLE POLE FCC ID: 2AUCU-141U1W IC: 25381-141U1W SQR141U1LAW and SQR141U1BKW have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction with SQR141U1WHW. The difference lies only model number and color. ______________________ Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen Date:12/16/2020

Schneider Electric (China) Co., Ltd., Shenzhen Branch Date: Dec. 1 st , 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Title of Person：Manager Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen

Schneider Electric (China) Co., Ltd., Shenzhen Branch Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AUCU-141U1W To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Contact Name: Tony Huang Title of Person：Manager Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen Date: Dec. 1 st , 2020

Appendix I External Photographs Page 2 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-1 View of EUT-2 Page 3 of 3 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. View of EUT-3 View of EUT-4

｝ Original format A4 A B C D E F A B C D E F 1 2 34 State: 00 1/1 Document Number: Doc. Rev. Sheet: 1.000 mm Scale: Technical Specification: Units of measure : The information is highly confidential and is the exclusive property of Schneider Electric copyright reserved. This drawing must not be used for any purpose other than that expressly permitted in writing by the owners and must not be disclosed or reproduced in any way without permission from the owners in writing. This drawing must be returned to the owners when the purpose has ceased. Provisional NOTES: *** ARTWORK IS THE MASTER FOR COLOUR, FONT, SIZE & LOGO'S*** 1. TEST FOR MARKINGS: REFER TO CQCS 2. LOCATION OF MARKING: POSITION AS SHOWN 3. FONT: ARIAL ROUNDED 4. TEXT HEIGHT: AS INDICATED 5. SQUARE D LOGO SIZE: 2.73MM(H)*13.79MM(L)(Pantone Cool grey 6C) 6. MINIMUM SIZE: 0.5 inch (12.7mm) 1/2 inch (4 mm) (2.4 mm) MARKING DETAIL WIFI SWITCH SQR141U1WHW Resistive: 1800W (15A) Standard ballast: 1200VA lncandescent: 1000W Reset LED: 5A Motor: 1/2HP 120VAC, 60Hz INDOOR USE ONLY YYYYMMDD SSIDSE-XXXXXXXXXXXX KeysXXXXXXXXXXXXXXX STRIP GAUGE LOAD TRAVELER HOT NEUTRAL Made in China 1/2 inch FCC ID : 2AUCU-141U1W CAN ICES-003(B)/NMB-003(B) IC: 25381-141U1W For supply connections, for at least 90°C use 12-14 AWG wires rated Energy Monitoring E515069

Appendix II Internal Photographs Page 2 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-1 Internal View of EUT-2 Page 3 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-3 Internal View of EUT-4 Page 4 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-5 Internal View of EUT-6 Antenna Page 5 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-7 Internal View of EUT-8 Page 6 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-9

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. This report does not imply that the product(s) has met the criteria for certification. FCC RF EXPOSURE REPORT For WI-FI SWITCH SINGLE POLE MODEL NUMBER: SQR141U1WHW, SQR141U1LAW, SQR141U1BKW FCC ID: 2AUCU-141U1W REPORT NUMBER: 4789727726-2 ISSUE DATE: February 01, 2021 Prepared for Schneider Electric (China) Co., Ltd., Shenzhen Branch Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi-Tech Development Zone, Dongguan, People’s Republic of China Tel: +86 769-22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT No.: 4789727726-2 Page 2 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 3 2. TEST METHODOLOGY ..................................................................................................... 4 3. FACILITIES AND ACCREDITATION ................................................................................. 4 4. EQUIPMENT UNDER TEST ............................................................................................... 5 4.1. DESCRIPTION OF EUT .............................................................................................. 5 5. REQUIREMENT ................................................................................................................. 6 REPORT No.: 4789727726-2 Page 3 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Manufacturer Information Company Name: Schneider Electric (China) Co., Ltd., Shenzhen Branch Address: Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China EUT Information EUT Name: WI-FI SWITCH SINGLE POLE Model: SQR141U1WHW Series Model: SQR141U1LAW, SQR141U1BKW Model difference: Please refer to clause 4.1. Description of EUT Brand: Schneider Electric / Square D Sample Received Date: December 11, 2020 Sample Status: Normal Sample ID: 3522310 Date of Tested: December 11, 2020~ December 18, 2020 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47CFR§2.1091 KDB-447498 D01 V06 PASS Prepared By: Checked By: Kebo Zhang Shawn Wen Project Engineer Laboratory Leader Approved By: Stephen Guo Laboratory Manager REPORT No.: 4789727726-2 Page 4 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with KDB 447498 D01 General RF Exposure Guidance v06. 3. FACILITIES AND ACCREDITATION Accreditation Certificate A2LA (Certificate No.: 4102.01) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with A2LA. FCC (FCC Designation No.: CN1187) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. Has been recognized to perform compliance testing on equipment subject to the Commission's Delcaration of Conformity (DoC) and Certification rules ISED(Company No.: 21320) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been registered and fully described in a report filed with Industry Canada. The Company Number is 21320. VCCI (Registration No.: G-20019, R-20004, C-20012 and T-20011) UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch. has been assessed and proved to be in compliance with VCCI, the Membership No. is 3793. Facility Name: Chamber D, the VCCI registration No. is G-20019 and R-20004 Shielding Room B , the VCCI registration No. is C-20012 and T-20011 Note 1: All tests measurement facilities use to collect the measurement data are located at Building 10, Innovation Technology Park, Song Shan Lake Hi tech Development Zone, Dongguan, 523808, China Note 2: The test anechoic chamber in UL Verification Services (Guangzhou) Co., Ltd. Song Shan Lake Branch had been calibrated and compared to the open field sites and the test anechoic chamber is shown to be equivalent to or worst case from the open field site. Note 3: For below 30MHz, lab had performed measurements at test anechoic chamber and comparing to measurements obtained on an open field site. And these measurements below 30MHz had been correlated to measurements performed on an OFS. REPORT No.: 4789727726-2 Page 5 of 6 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 4. EQUIPMENT UNDER TEST 4.1. DESCRIPTION OF EUT EUT Name WI-FI SWITCH SINGLE POLE Model SQR141U1WHW Series Model SQR141U1LAW, SQR141U1BKW Model difference SQR141U1WHW, SQR141U1LAW, SQR141U1BKW are identical except for color. Radio Technology WLAN (IEEE…

Text truncated - open the document above for the full version.

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C ISED RSS-247 ISSUE 2 CERTIFICATION TEST REPORT For WI-FI SWITCH SINGLE POLE MODEL NUMBER: SQR141U1WHW, SQR141U1LAW, SQR141U1BKW FCC ID: 2AUCU-141U1W IC: 25381-141U1W REPORT NUMBER: 4789727726-1 ISSUE DATE: February 01, 2021 Prepared for Schneider Electric (China) Co., Ltd., Shenzhen Branch Room 201, Building A, No. 1 Qianwanyi Road, Shengang Cooperation Zone, Qianhai, Shenzhen, China Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi- Tech Development Zone Dongguan, 523808, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4789727726-1 Page 2 of 102 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No: 10-SL-F0088 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 02/01/2021 Initial Issue REPORT NO.: 4789727726-1 Page 3 of 102 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No: 10-SL-F0088 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Clause Test Items FCC/ISED Rules Test Results 1 6dB Bandwidth and 99% Occupied Bandwidth FCC Part 15.247 (a) (2) RSS-247 Clause 5.2 (a) ISED RSS-Gen Clause 6.7 Pass 2 Conducted Output Power FCC Part 15.247 (b) (3) RSS-247 Clause 5.4 (d) Pass 3 Power Spectral Density FCC Part 15.247 (e) RSS-247 Clause 5.2 (b) Pass 4 Conducted Bandedge and Spurious Emission FCC Part 15.247 (d) RSS-247 Clause 5.5 Pass 5 Radiated Bandedge and Spurious Emission FCC Part 15.247 (d) FCC Part 15.209 FCC Part 15.205 RSS-247 Clause 5.5 RSS-GEN Clause 8.9 Pass 6 Conducted Emission Test for AC Power Port FCC Part 15.207 RSS-GEN Clause 8.8 Pass 7 Antenna Requirement FCC Part 15.203 RSS-GEN Clause 6.8 Pass Note: 1. This test report is only published to and used by the applicant, and it is not for evidence purpose in China. 2. The measurement result for the sample received is <Pass> according to < CFR 47 FCC PART 15 SUBPART C >< ISED RSS-247 > when <Accuracy Method> decision rule is applied. REPORT NO.: 4789727726-1 Page 4 of 102 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM No: 10-SL-F0088 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 6 2. TEST METHODOLOGY ..................................................................................................... 7 3. FACILITIES AND ACCREDITATION ................................................................................. 7 4. CALIBRATION AND UNCERTAINTY ................................................................................ 8 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 8 4.2. MEASUREMENT UNCERTAINTY ............................................................................... 8 5. EQUIPMENT UNDER TEST ............................................................................................... 9 5.1. DESCRIPTION OF EUT .............................................................................................. 9 5.2. CHANNEL LIST ........................................................................................................... 9 5.3. MAXIMUM OUTPUT POWER...................................................................................... 9 5.4. TEST CHANNEL CONFIGURATION ........................................................................... 9 5.5. THE WORSE CASE POWER SETTING PARAMETER ..............................................10 5.6. THE WORSE CASE CONFIGURATIONS ..................................................................11 5.7. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................12 5.8. DESCRIPTION OF TEST SETUP ...............................................................................13 6. MEASURING INSTRUMENT AND SOFTWARE USED ....................................................13 7. ANTENNA PORT TEST RESULTS ...................................................................................16 7.1. ON TIME AND DUTY CYCLE .....................................................................................16 7.2. 6 dB DTS BANDWIDTH AND 99 % OCCUPIED BANDWIDTH ..................................17 7.3. CONDUCTED OUTPUT POWER ...............................................................................19 7.4. POWER SPECTRAL DENSITY ..................................................................................20 7.5. CONDUCTED BANDEDGE AND SPURIOUS EMISSIONS ........................................22 8. RADIATED TEST RESULTS .............................................................................................24 8.1. RESTRICTED BANDEDGE ........................................................................................30 8.1.1. 802.11b SISO MODE ...........................................................................................30 8.1.2. 802.11g SISO MODE ...........................................................................................32 8.1.3. 802.11n HT20 SISO MODE .........................…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs RADIATED RF MEASUREMENT SETUP (30MHz ~ 1 GHz) RADIATED RF MEASUREMENT SETUP (Below 30MHz) RADIATED RF MEASUREMENT SETUP (Above 1G – X axis) RADIATED RF MEASUREMENT SETUP (Above 1G – Y axis) RADIATED RF MEASUREMENT SETUP (Above 1G – Z axis) POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP