2AUTE-2TS25GPortable Photo Printer, INSTANT CAMERA

01 02 03 Power-on Long press the power button until the LED indicator is lit and when it is released, the device is turned on. Adjust filter Rotate the filter switch knob to change the current gear and select different filter effects. Turn on the flash Toggle the flash button to turn the flash on /off. Take pictures and print When you press the shutter button, the printer completes the viewfinder and prints the photo immediately. Z6 Lanyard Note: The shooting function cannot be used in print or charg mode. 4 3 2 1 1 2 3 ！ Front View： Rear View： Product Introduction Accessories Quick Start GuideUSB Cable * Note: The items in the package are actually based on the order . Side View： Inner： Product Introduction Product Parameters Product Name Portable Photo Printer Printer Model HCP-2TS25G Dimensions 121*101*47mm Weight Bare machine 340g Print Method Thermal Dye Sublimation Print Size 54*72mm Print Resolution 300dpi Battery Capacity 800mAh Charging Interface 5V / 2A，type-C Interface Operating Temperature 5°C~35°C Take out a consumable, put it into the compartment according to the direction shown below, place your finger in the “push” position and press it into place until it makes a “click” sound. Consumable Installation Instructions 1. The photo parer is susceptible to moisture, please use it as soon as possible after opening. 2. This device only supports official photo paper that comes with the ribbon, please do not replace it by yourself. 3. Avoid excessive direct sunlight and low temperature. 4. If the ink cassette is damaged or deformed by external force, please do not insert it into the deviceby force. Printing Instructions Close the consumble compartment. Open the supplies inlet cover As shown, open the cover. Supplies Inlet Cover Power Button /LED Indicator Speaker Hole Lanyard Hole Paper Outlet Flash Selfie Lens View Frame Shutter Button Flash Button Filter Switch Knob APP Print 1 Scan the QR code to download the "HeyPhoto" APP 1. Open the APP and click “Add device”； 2. Search “Z6-XXXX” and click to connect. In the app, select the photos you want to print. You can also edit the photos as needed before printing. 1. After the first connection, you just need to click the print icon for subsequent use, the printer will be automatically connected and print. 2. Do not exit the APP during the printing process, this may cause printing failure. 3. APP page may change with the version, please refer to the actual interface. ManufacturerXiamen Hanin Co.,Ltd. Factory AddressNo.96, RongYuan Road, Tong'an District, Xiamen City, Fujian Province, P.R. China E-mail: [email protected] Web: www.hprt.com Consumable Toggle the flash button to turn the flash on(-) / off(o) Short press the shutter button to complete the viewfinder and print the photo immediately Long press the power button to turn on / off the device Function Button Operation Instructions Function Button Icon State Flash Button Shutter Button Power Button Battery Charging 1. When the battery power is low，please charge it by the equipped USB cable in time. If you continue printing, it may power off automatically. 2. Plug one end of the USB cable into the printer’s port, and connect the other end to the power adapter. After connecting, the printer enters a charging state, at which point printing will interrupt the charging state. 3. The charging time is about 90-120 minutes. Charge via Adapter 1. The printer can be charged via computer or adaper with USB cable. Please note that the adapter is not equipped with the printer. Users who use power adapters for charging should purchase and use power adapters that are certified for safety and meet the requirements of the standard. 2. Users are prohibited from disassembling the machine by themselves, if replacing the wrong model of battery will be at risk of explosion. Please be sure to dispose of the used battery according to the instructions. 3. When the printer is low power, please charge it for a period of time before using it, so as to avoid interrupting printing due to insufficient power during use. WARNING: Operating this device may cause radio interference in a residential environment. Precautions 1. The best working temperature of the printer is 5°C~35°C. If the ambient temperature is too high, the printing quality may be affected; 2. Please use official ribbon and photo paper to ensure print quality; 3. Avoid disassembling the ribbon and photo paper by yourself. If the glossy surface of the photo paper is polluted, the printing quality will be affected; 4. Do not pull out the consumable forcibly during printing, this may damage the printer; 5. When not in use for a long time, close the consumable compartment to keep things like dust out; 6. After printing multiple photos in a row, the device may activate overtemperature protection, which is normal, and the current task will continue to be printed after cooling; 7. Do not perform any operations while the device is turning on. Operating Environment 1. Place the printer on a desktop or other flat, stable surface; 2. Please make sure that there is more than 10 cm space in the paper outlet of the printer. 3 1 2 1 Orange LED indicator is lighting Orange LED indicator flashes slowly Red LED indicator is lighting Red LED indicator flashes slowly Red LED indicator flashes quickly Status LED Indicator LED Indicator Status LED IndicatorStatus Out-of-paper/lack of ink/ lack of ink cassette Paper jam/ink cassette jam Low power Device is over temperature/ device abnormality Abnormal ink cassette/ ink cassette not recognized Error Status Printer Status Blue LED indicator is lighting Ready to use normally Printing/Bluetooth data distribution in progress Device starting up Blue LED indicator flashes slowly Blue LED indicator flashes quickly Green LED indicator flashes slowly Battery Charging in Progress (Power On/Off) Fully charged while powered on Fully charge in power-off state Blue LED indicator is lighting Green light remains on the indicator turns off …

Text truncated - open the document above for the full version.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Picus Advisors US LLC FRN: 0034336891 Contact Name: lvan Wang Address: 5855 SOVEREIGN DRSTE B-1, HOUSTON, TX 77036, USA Telephone No: +1(713) 271-9600 Email: [email protected] Applicant: Company name: Xiamen Hanin Co.,Ltd. FRN: 0028895233 Product Description: Portable Photo Printer, INSTANT CAMERA Grantee code: 2AUTE FCC ID: 2AUTE-2TS25G Contact Name: Jeff Wang Address: Room 305A, Angye Building, Pioneering Park, Torch High-tech Zone, Xiamen City, China Telephone No: 13799700032 Email: [email protected] [Xiamen Hanin Co.,Ltd.] certifies that, as of the date of this filing of the application with the TCB, [Picus Advisors US LLC] is our designated US agent for service of process for the above referenced FCC ID. [Xiamen Hanin Co.,Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Picus Advisors US LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 11.24.2025 Applicant’s Name: Jeff Wang US Agent’s Name: lvan Wang Title: Certified Engineer Title: CEO Signature Signature

Attestation Statement. Old Code: C5266091 24 New Code: 00015544 Ed.3 Change reason: FRN is added to the Applicant information section. 1/1 TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Xiamen Hanin Co.,Ltd. Grantee code: 2AUTE FCC ID: 2AUTE-2TS25G FRN: 0028895233 Contact Name: Jeff Wang Address: Room 305A, Angye Building, Pioneering Park, Torch High-tech Zone, Xiamen City, China Telephone No: 13799700032 Fax No: +86-(0)592-5930505 Email: [email protected] i. [Xiamen Hanin Co.,Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Xiamen Hanin Co.,Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. Xiamen Hanin Co.,Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Date: 11.24.2025 Applicant’s Name: Jeff Wang Title: Certified Engineer Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

Xiamen Hanin Co.,Ltd. Code 00018768 Ed. 2 Item 1. The device is able to install software/program installation? ☐Yes, go to Item 2. ☒No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky cybersecurity or anti-virus software. Item 2. Technical Requirements for Kaspersky Cybersecurity Software: # General Requirements (For all Devices) Yes / No or N/A Comments 1 Internet connection for activation and updates (For all Operating Systems) N/A Device Portable Photo Printer, INSTANT CAMERA Company name Xiamen Hanin Co.,Ltd. Grantee code 2AUTE FCC ID 2AUTE-2TS25G FRN 0028895233 Contact name Jeff Wang Address Room 305A, Angye Building, Pioneering Park, Torch High-tech Zone, Xiamen City, China Telephone number 13799700032 [email protected] Chipset/module information WS1830S, BR8051A01 Operating System (if applicable) N/A Storage Capacity (hard drive or other permanent memory storage, if applicable) N/A 2 # General Requirements (For Windows Devices) Yes / No or N/A Comments 1 Storage: 1500 MB free space on the hard drive N/A 2 Operating System: Microsoft Windows 8, 8.1, 10 & 11 Home / Pro / Enterprise Microsoft Windows 7 Starter / Home Basic & Premium / Professional / Ultimate SP1 or higher N/A 3 Processor: 1 GHz or higher (x86 or x64) N/A 4 Memory (RAM)1 GB (32-bit) or 2 GB (64-bit) N/A 5 Screen Resolution: Minimum resolution of 1024 x 768 N/A # General Requirements (For macOS devices) Yes / No or N/A Comments 1 Operating System macOS® 13 – 14 N/A 2 Memory (RAM)4 GB N/A 3 Storage: 3455 MB free space on the hard drive N/A # General Requirements (For Android Devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: Android™ 10 – 14 N/A 3 Screen Resolution: Minimum resolution of 320 x 480 N/A # General Requirements (for iOS devices) Yes / No or N/A Comments 1 Storage: 150 MB free space N/A 2 Operating System: iOS® 17 N/A 3 # General Requirements (For Linux system) Yes / No or N/A Comments 1 Hard drive: 1 GB of free space N/A 2 CPU: Intel Pentium 1 GHz or higher N/A 3 RAM: 1 GB N/A 4 Minimum software requirements: AlmaLinux OS 8 or later; AlterOS 7.5 or later; Astra Linux Common Edition 2.12 or later; CentOS 6.7 or later; Debian GNU/Linux 10.0 or later; EulerOS 2.0 or later; Oracle Linux 7.3 or later ; Red Hat Enterprise Linux 6.7 or later ; Rocky Linux 8.5 or later ; SUSE Linux Enterprise Server 12.5 or later; Ubuntu 12.04 or later ; Uncom OS Home / Business / Education / Enterprise 2.2 or later; ALT Linux Workstaton / Workstation K / Server / Education 8 or later; ROSA Linux Workstation / Server 12 or later ; RED OS 7.3 and later ; N/A After reviewed the technical requirements, is the device capable of supporting the installation of Kaspersky software? ☐ Yes, go to Item 3. ☒ No. In this case, the rest of the items do not apply. The device cannot support installation of Kaspersky software 4 Item 3. Connectivity Capabilities: # Physical Interface Purpose Justification 1 1 # Wireless Interface Purpose Justification 1 1 After the review of this items, the device: ☒ Cannot support installation of any cybersecurity or anti-virus software on the covered list. ☐ Potentially can operate with any cybersecurity or anti-virus software on the covered list – additional third- party proof is provided to demonstrate compliance with requirements as of 2.911(d)5(i),(ii) – “Proof of Compliance with Covered List Software Requirements” of this document applies Signature: Name: Jeff Wang Date: 11/24/2025 1 The justification field is used to justify why the software cannot be received through that interface. Check the annex for more indications.

Xiamen Hanin Co.,Ltd. Product Similarity Declaration Product name: Portable Photo Printer, INSTANT CAMERA Model name: HCP-2TS25G, Z6, HPRT Z6 FCC ID: 2AUTE-2TS25G We (Xiamen Hanin Co.,Ltd.) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name. Signature: Name: Jeff Wang Title: Certified Engineer Date: 11/24/2025

TCB CALL página 1 File FCC ID: 2AUTE-2TS25G Please upload an exhibit that explains how does the TCB verify the new agent information: 1- Is the address of the agent a valid physical US mailing address (not a US post office box, not a virtual mailbox, not P.O. Boxes, not a vacant lot, not a public building, etc.) ○ We have checked if the address exists in a real and potential building (Google maps) + official US register, after this verification and the evidence below we can guarantee the following: not a US post office box not a virtual mailbox not P.O. Boxes not a vacant lot not a public building(note) ► We checked the FCC FRN Search based on the information provided by the grantee. Google: TCB CALL página 2 EIN Statement TCB CALL página 3 ► CONCLUSION by TCB: The ASOP defined and provided by grantee is VALID and confirmed. Therefore the exhibit "C5266091_X23_Ed1_US_Agent_Letter" included in the file is ok. 2- Is the agent physically located at that valid US address such that the agent can be legally served at that address? Yes , check above 3- Has the listed agent clearly agreed in writing to serve as the agent for the grantee at that address? Yes, it is included in the exhibit "C5266091_X23_Ed1_US_Agent_Letter"

C5266091_X10_Ed.2 1/1 Xiamen Hanin Co.,Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 11/24/2025 Subject: Request for Confidentiality FCC ID: 2AUTE-2TS25G To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Jeff Wang Title: Certified Engineer

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Xiamen Hanin Co.,Ltd. Address: Room 305A, Angye Building, Pioneering Park, Torch High-tech Zone, Xiamen City, China Product Name: Portable Photo Printer, INSTANT CAMERA Model Number: HCP-2TS25G, Z6, HPRT Z6 FCC Identifier: 2AUTE-2TS25G We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jeff Wang Date: 11/24/2025 Title: Certified Engineer Signature of applicant:

Page 1 of 4 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Photographs of the EUT (External Photos) Model: HCP-2TS25G Page 2 of 4 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 3 of 4 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 4 of 4 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected]

Page 1 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Photographs of the EUT (Internal Photos) Model: HCP-2TS25G Page 2 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 3 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 4 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] BT ANT Page 5 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] RF ID Coil Page 6 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 7 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 8 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 9 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Page 10 of 10 Report No.: MTi250811013-0107 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected]

Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE012 Ver./Rev.：A1 Page 1 of 7 RFEXPOSURE TestReport ReportNo.: MTi250811013-0107E4 DateofIssue: 2025-09-16 Applicant: XiamenHaninCo.,Ltd. Product: PortablePhotoPrinter,INSTANTCAMERA Model(s): HCP-2TS25G,Z6,HPRTZ6 FCCID: 2AUTE-2TS25G ShenzhenMicrotestCo.,Ltd. TESTREPORT ReportNo.:MTi250811013-0107E4 Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE012 Ver./Rev.：A1 Page2of7 Tableofcontents 1StandaloneSARtestexclusionconsiderations.................................................................4 2SARTestExclucsionThresholds.........................................................................................5 TESTREPORT ReportNo.:MTi250811013-0107E4 Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE012 Ver./Rev.：A1 Page3of7 TestResultCertification ApplicantXiamenHaninCo.,Ltd. ApplicantAddress Room305A,AngyeBuilding,PioneeringPark,TorchHigh-techZone,Xiamen City,China ManufacturerXiamenHaninCo.,Ltd. Manufacturer Address Room305A,AngyeBuilding,PioneeringPark,TorchHigh-techZone,Xiamen City,China Productdescription ProductnamePortablePhotoPrinter,INSTANTCAMERA TrademarkN/A ModelnameHCP-2TS25G SeriesModel(s)Z6,HPRTZ6 Standards47CFRPart2.1093 TestmethodKDB447498D01v06Section4.3.1 TestingInformation Dateoftest2025-08-21to2025-09-16 TestResultPass Preparedby:LetterLan Reviewedby:DavidLee Approvedby:LewisLian TESTREPORT ReportNo.:MTi250811013-0107E4 Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE012 Ver./Rev.：A1 Page4of7 1StandaloneSARtestexclusionconsiderations UnlessspecificallyrequiredbythepublishedRFexposureKDBprocedures,standalone1-g headorbodyand10-gextremitySARevaluationforgeneralpopulationexposureconditions,by measurementornumericalsimulation,isnotrequiredwhenthecorrespondingSARTest ExclusionThresholdcondition(s),listedbelow,is(are)satisfied. Thesetestexclusionconditionsarebasedonsource-basedtime-averagedmaximum conductedoutputpoweroftheRFchannelrequiringevaluation,adjustedfortune-uptolerance, andtheminimumtestseparationdistancerequiredfortheexposureconditions. Theminimumtestseparationdistancedefinedin4.1f)isdeterminedbythesmallestdistance fromtheantennaandradiatingstructuresoroutersurfaceofthedevice,accordingtothehost formfactor,exposureconditionsandplatformrequirements,toanypartofthebodyorextremity ofauserorbystander. ToqualifyforSARtestexclusion,thetestseparationdistancesappliedmustbefullyexplained andjustified,typicallyintheSARmeasurementorSARanalysisreport,bytheoperating configurationsandexposureconditionsofthetransmitterandapplicablehostplatform requirements,accordingtotherequiredpublishedRFexposureKDBprocedures. WhennootherRFexposuretestingorreportingarerequired,astatementofjustificationand compliancemustbeincludedintheequipmentapproval,inlieuoftheSARreport,toqualifyfor SARtestexclusion. Whenrequired,thedevicespecificconditionsdescribedintheotherpublishedRFexposure KDBproceduresmustbesatisfiedbeforeapplyingtheseSARtestexclusionprovisions. a)For100MHzto6GHzandtestseparationdistances≤50mm,the1-gand10-gSARtest exclusionthresholdsaredeterminedbythefollowing: [(max.powerofchannel,includingtune-uptolerance,mW)/(min.testseparationdistance, mm)]·[√f(GHz)]≤3.0for1-gSAR,and≤7.5for10-gextremitySAR,where  f (GHz) istheRFchanneltransmitfrequencyinGHz PoweranddistanceareroundedtothenearestmWandmmbeforecalculation Theresultisroundedtoonedecimalplaceforcomparison Thevalues3.0and7.5arereferredtoasnumericthresholdsinstepb)below Thetestexclusionsareapplicableonlywhentheminimumtestseparationdistanceis≤50mm, andfortransmissionfrequenciesbetween100MHzand6GHz.Whentheminimumtest separationdistanceis<5mm,adistanceof5mmaccordingto4.1f)isappliedtodetermine SARtestexclusion. b)For100MHzto6GHzandtestseparationdistances>50mm,the1-gand10-gSARtest exclusionthresholdsaredeterminedbythefollowing(alsoillustratedinAppendixB): 1){[Powerallowedatnumericthresholdfor50mminstepa)]+[(testseparation distance–50mm)·(f(MHz)/150)]}mW,for100MHzto1500MHz 2){[Powerallowedatnumericthresholdfor50mminstepa)]+[(testseparation distance–50mm)·10]}mW,for>1500MHzand≤6GHz c)Forfrequenciesbelow100MHz,thefollowingmaybeconsideredforSARtestexclusion (alsoillustratedinAppendixC): 1)Fortestseparationdistances>50mmand<200mm,thepowerthresholdatthe correspondingtestseparationdistanceat100MHzinstepb)ismultipliedby[1+ log(100/f(MHz))] TESTREPORT ReportNo.:MTi250811013-0107E4 Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE012 Ver./Rev.：A1 Page5of7 2)Fortestseparationdistances≤50mm,thepowerthresholddeterminedbythe equationinc)1)for50mmand100MHzismultipliedby½ 3)SARmeasurementproceduresarenotestablishedbelow100MHz. WhenSARtestexclusioncannotbeapplied,aKDBinquiryisrequiredtodetermineSAR evaluationrequirementsforanySARtestresultsbelow100MHztobeacceptable. 2SARTestExclucsionThresholds Weuse5mmasseparationdistancetocalculated. BluetoothDSS: Transmit Frequency (GHz) Mode Measured Power (dBm) Tune-up power (dBm) Maxtune-upResult 1gSAR test exclusion threshold power(dBm)calculation 2.402 GFSK -2.47-2±1-10.24623 2.441-2.16-2±1-10.24823 2.48…

Text truncated - open the document above for the full version.

Tel:0755-88850135-1439 Mobile:131-4343-1439（Wechatsamenumber） Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.：A1 Page 1 of 50 TestReport ReportNo.:MTi250811013-0107E2 Dateofissue:2025-09-16 Applicant:XiamenHaninCo.,Ltd. Product:PortablePhotoPrinter,INSTANTCAMERA Model(s):HCP-2TS25G,Z6,HPRTZ6 FCCID:2AUTE-2TS25G ShenzhenMicrotestCo.,Ltd. TESTREPORT ReportNo.:MTi250811013-0107E2 Tel:0755-88850135-1439Mobile:131-4343-1439(Wechatsamenumber)Web:http://www.mtitest.cnE-mail:[email protected] Address:101,No.7,Zone2,XinxingIndustrialPark,FuhaiAvenue,XinheCommunity,FuhaiStreet,Bao’anDistrict,Shenzhen,Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.：A1 Page 2 of 50 Tableofcontents 1GeneralDescription.......................................................................................................................4 1.1DescriptionoftheEUT............................................................................…

Text truncated - open the document above for the full version.