2BABY696MET8024UNDERCABINET BLUETOOTH SPEAKER WITH FM RADIO

USER MANUAL Please read car efully befor e use and keep for future refer ence. UNDER CABINET BLUETOOTH® SPEAKER WITH FM RADIO EKR-1000 TM 2 1. Read these instructions – All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions. The safety and operating instructions should be retained for future reference. 3. Heed all warnings. All warnings on the appliance and in the operating instructions should be adhered to. 4. Do not use this apparatus near water. The device should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like. 5. Clean only with a dry cloth. 6. Do not block any ventilation openings. 7. Do not operate or place near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Protect the power cord from being walked on or pinched particularly at the plugs, power outlets, and at the point where they exit from the apparatus. 9. Only use attachments/accessories specified by the manufacturer. 10. Unplug the apparatus during lightning storms or when unused for long periods of time. 11. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as a damaged power supply cord or plug. 12. WARNING: To reduce the risk of fire or electric shock, do not expose this device to any moisture, including rain or high humidity. Do not place any vases, or any liquid containers on the speaker. 13. Only use the device in moderate climates. 14. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. 15. Do not place open flame sources, such as lighted candles, on the apparatus. 16. CAUTION: These servicing instructions are for use by qualified service personnel only. 17. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 18. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO DOT REMOVE THE DEVICE HOUSING. DO NOT OPEN THE UNIT. SERVICING SHALL ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL. 19. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications. 20. Stop operation immediately if any liquid or solid object should fall into the cabinet. SAFETY INSTRUCTIONS 3 PACKAGE CONTENTS Main Unit...................1 Piece AC Adaptor ................1 Piece DEVICE SPECIFICATIONS NOTE: SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE 21. sources are disconnected from the unit. Unplug the AC-DC adaptor from the wall not by pulling the cor d. 22. 23. turning the power on, or gradually heat the room up and dry the unit befor e use. 24. Should any trouble occur, r emove the power source and refer servicing to Power Adaptor AC Input: 120 ~ 60Hz DC Output: 5V 1.2A Bluetooth Data Ver sion 5.3 10W Radio Frequency RangeFM: 87.5 - 108 MHz Audio Output Power 2W x 2 Tot al 4W RMS Approximate Dimensions2.6 in. (H) x 9.1 in. (W) x 6.7 in. (D) Weight1.2 LBS User Manual ..............1 Piece ..............1 Set 4 DEVICE FEATURES & CONTROLS Fr ont View 12 345 67 8 91011131412 15 16 17 5 Rear View 1. MICROPHONES 2. PM INDICATOR 3. LCD DISPLAY 4. BT INDICATOR 5. / SOURCE BUTTON 6. VOL - BUTTON 7. VOL + BUTTON 8. TIMER/LIGHT BUTTON 9. TIMER INDICATOR 10. FM INDICATOR 11.  /SCAN/PAIR ( BUTTON 12.  SKIP - BUTTON 13.  SKIP + BUTTON 14. CLK/PRESET/ ( BUTTON 15. LED LAMP 16. SPEAKER (L) 17. SPEAKER (R) 18. FM WIRING ANTENNA 19. DC INPUT JACK 19 18 6 AC POWER WARNING: apparatus. NOTE: Only use the supplied power adapter . 1. Connect the AC end of AC/DC adapter into an AC wall outlet. 2. Insert the DC plug of the AC adapter cor d into the DC IN JACK at the back of the unit. CONNECTING POWER

7 SETTING THE CLOCK 1. In standby mode, press and hold the CLK / PRESET BUTTON. “12H” will blink. 2. Pr ess the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to set the 12- Hour or 24-Hour format. 3. 4. Pr ess the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to set the current hour. 5. 6. Pr ess the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to set the current minute. 7. NOTES: • occurs, you will need to reset the clock. • The PM indicator will light when the 12-hour format is selected. SETTING THE TIMER show in LCD Display. 1. minutes. 2. Pr ess the After the set time is reached, the EKR-1000 alarm will sound. /SKIP+ / TUNE+ BUTTON or /SKIP- / TUNE- BUTTON to adjust the 3. 4. OPERATING THE DEVICE 8 OPERATING MODES LISTENING TO THE RADIO 1. Pr ess the / SOURCE BUTTON to turn on the EKR-1000. 2. Pr ess the / SOURCE BUTTON repeatedly to select the FM band. The FM indicator and frequency will show on LCD display. a. Manual Tuning: i) P ii) If the reception is poor, try manual tuning to fine-tune the station. Press the ress and hold the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON briefly to manually tune through the frequency band. /SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON iii) Adjust the VOL + / VOL – to obtain the desired volume level. i. Press the SCAN BUTTON for more than 2 seconds. The unit will auto scan 3. NOTE: / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to check the tuned frequency. SETTING THE RADIO STATION PRESETS To Manually Set Presets: 1. Pr ess the / SOURCE BUTTON to turn on the unit. 2. Pr ess the / SOURCE BUTTON repeatedly to select FM band. The FM indicator and frequency will show on LCD display. 3. Pr ess the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to select the 4. 5. Pr ess the / SKIP+ / TUNE+ BUTTON or / SKIP- / TUNE- BUTTON to select the desired program number. 6. 7. 8. 9 BLUETOOTH OPERATION 1. Pr ess the / SOURCE BUTTON to turn on the unit. 2. Pr ess the / SOURCE BUTTON repeatedly to select Bluetooth Mode. The “BT” Pairing/Discover able mode. 3. 4. Select “EMERSON EKR-1000” from the device list when it appears on your device screen. If required, enter the pass code “0000” to pair (link) the unit with your device. 5. If you are pairing (linking) your computer to the speaker using Bluetooth, you may need to set the EMERSON EKR-1000 as your computer ’s default sound device. 6. 7. If you want t o connect the unit to another Bluetooth device, press and hold the To Connect to a Previously Paired Bluetooth Device The EKR-1000 can stor e one previously paired device for quick pairing during power on. When the unit is power ed on and the previously paired device is found within the NOTE: • pairing process by pressing and holding the again and • Bluetooth device. • • Make sure your device is working properly. Check your device’s manual for details on Bluetooth pairing and linking. • Refer to manual of your cell phone, tablet PC, c omputer , or other Bluetooth to model.  /SCAN/PAIR ( BUTTON. The BT indicator will flash to confirm that the unit is  /SCAN/PAIR ( BUTTON in Pairing/Discoverable mode. Repeat steps 3 and 4. 10 PLAYING FROM A BLUETOOTH DEVICE 1. device or the on the unit to play or pause the Bluetooth device playback. 2. Adjust both the VOL + / VOL – BUTTONS of the unit and on your Bluetooth NOTES: • the music through the speaker , even if connected. • USING AS A HANDS-FREE SPEAKERPHONE To use the unit as a speakerphone for receiving a phone call from a Bluetooth enabled phone. 1. 2. When a call is received when music is pla ying, the music will be replaced by the ringtone. Press the once to answer the call. 3. 4. To ignore an incoming call, simply press the ( 5. When the call is completed, press the ( playing music from your cell phone to the unit befor e answering the call, the 6. Quickly press the twice to re-dial the last number you dialed. USING THE LIGHT FUNCTION Please and hold the LIGHT BUTTON to turn on the LED light. Please and hold LIGHT  /SCAN/PAIR ( BUTTON  /SCAN/PAIR ( BUTTON  /SCAN/PAIR ( BUTTON 11 RESETTING THE UNIT If the system does not respond or exhibits erratic or intermittent operation, you may have experienced an electrostatic discharge (ESD) or a power surge that triggered the internal microcontroller to shut down automatically. If this occurs, simply disconnect the AC Adaptor, wait for at least 3 minutes, and then setup the unit again as if you were using it for the very first time. CARE & MAINTENANCE CAUTION: Never allow any water or other liquids to get inside the unit while cleaning. 1. Clean the unit with a soft, damp (never wet) cloth. Solvent or detergent should never be used. 2. To reduce the risk of fire or electric shock, avoid operating your unit under direct sunlight or in hot, humid, or dusty places. 3. Keep your unit away from heating appliances and sources of electrical noise, such as fluorescent lamps or motors. 4. For better Clock Display clarity, avoid operating the unit under direct sunlight or in strong room illumination. 5. Unplug the unit from the electrical power outlet immediately in case of malfunction. 12 TROUBLESHOOTING SYMPTOMPOSSIBLE CAUSESPOSSIBLE REMEDIES The unit does not respond (no power). The unit is disconnected fr om the AC outlet. Reconnect to the AC outlet. The AC outlet has no power. Try the unit on another outlet. Unit is ON, but there is low or no volume. Volume set t oo low. increase the volume level. FM has no sound.Unit is not in Radio mode. repeatedly to select Radio mode. Bluetooth has no sound. Unit is not linked with your Bluetooth enabled device. Go through “Bluetooth link the speakers. Unit placement out of range. Relocate the unit within range (~30 feet). Your Bluetooth enabled device volume set t oo low. Increase volume level of your Bluetooth enabled device. Noise or sound is distorted on FM br oadcas t. Fine tune the FM FM wire antenna is not fully extended. Fully extend the FM wire antenna. Unit gets warm play at high volume. …

Text truncated - open the document above for the full version.

13 FCC NOTICE SUPPORT WARNING: responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tes ted and found to comply with the limits for a Class B digital device, pursuant t o part 15 of the FCC Rules. radiate radio frequency energy and, if not installed and used in accor dance with the is encouraged to try to correct the interfer ence by one or more of the following measures: • Reorient or relocate the receiving antenna. • • receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Please also visit us on the web at www.emersonaudio.com to get up to the minute contact Emerson Technical support. EMERSON Technical Support 2320 Eas t 49th Street Vernon, CA 90058 Tel: (866) 411-6292 Email: [email protected] Made in China This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

GuangXi Beiliu Jin Bao Electronic Co., Ltd. Attestation Statements June14.2023 TO: Federal Communications Commission Authorizati。nand Evaluation Division 7435 Oakland Mills Road Columba MD 21046 USA RE: Attestation Statements Part 2.911 (d)(7) request for 2BABY696MET8024 GuaneXi Beiliu JinBa。ElectronicCo .. Ltd. , the undersigned, hereby auth。rizeNaxa Electronics, Inc. to act as ou「designated U.S. agent for service of process, GuaneXi Beiliu Jin Bao Electronic Co .. Ltd. accepts to maintain an conclusion of any Commission-related proceeding involving the equipment. Applicant lnformati。n: Company name: GuangXi Beiliu JinBao Electronic co., Ltd. Contact Name: Jim Wong Address: XinShan Industrial Zone, Xiliang Town, Beiliu City, Guangxi, China Telephone No: 86-13686493273 Email: [email protected] Signature 妒大 U.S. Agent lnformati。n: Company name: Naxa Electronics, Inc. Address: 2320 East 49th Street, Vernon California, CA90058, USA FRN: 0025676834 Contact Name: Michael Shak Telephone No: 3235838883 Email:mike(@naxa.com Signature 对认

EUT EXTERNAL PHOTOGRAPHS ----------------The end----------------

50mm 25mm EKR-1000 UNDERCABINET BLUETOOTH® SPEAKER WITH FM RADIO Frequency range : FM: 87.5-108 MHz POWER SOURCE: DC 5V 1.2A EXTERNAL FCC ID: 2BABY696MET8024 MADE IN CHINA4491-06-2023 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

EUT INTERNAL PHOTOGRAPHS FPC antenna ----------------The end----------------

FCC ID: 2BABY696MET8024 RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500- 100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500- 100000 -- -- 1 30 11.1 Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm 2 ,If we know the maximum gain of the nd total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. RF Exposure Information: The radiated output power of this device meets the limits of FCC/IC radio frequency exposure limits.This device should be operated with a minimum separation distance of 20cm (8 inches) between the equipment and a person's body. 11.2 Measurement Result BT’ Power Max: -11.82 dBm Antenna gain: -0.68 dBi Measured power (dBm) Tune-up power (dBm) Max tune-up power (dBm) Antenna Gain Numeric Evaluation result (mW/cm2 ) Power density Limits (mW/cm2 ) -11.82 -12 to -10 -10 0.86 0.00002 1 *** End of Report ***

Inverted F Antenna Report Summary ITEM ANT SPEC Model Name 2.4G ANT Center Frequency Horizontal Vertical 2400MHz 2450MHz 2500MHz 2400MHz 2450MHz 2500MHz -1.73 -0.84 -0.68 -6.15 -3.70 -2.32 MAX. Gain -0.68 Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Antenna Length 38.20mm Manufacture ZHUHAI JIELI TECHNOLOGY CO., LTD. Address No. 333, KeXing Road, XiangZhou District, Zhuhai City. Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Frequency (MHz) Gain(dB) Max Min Avg 2400 -1.73178 -30.0815 -8.48713 2450 -0.845801 -38.5605 -7.88012 2500 -0.685586 -24.0318 -6.79139 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Frequency (MHz) Gain(dB) Max Min Avg 2400 -6.1530 -24.1420 -13.0295 2450 -3.7054 -26.5836 -10.6700 2500 -2.32122 -30.4301 -9.70536 ANT Test Labs：Attestation of Global Compliance Co., Ltd. Tested by: Cheung Yin Confirmed by: Yip Kin Tsuen

Report No. ENS2305250104W00201R Page 1 of 65 Ver.1.0 TEST REPORT Product Name : UNDERCABINET BLUETOOTH SPEAKER WITH FM RADIO Model Number : MET8024, EKR-1000, EKT-1000, NKR-1000, MD8024 FCC ID : 2BABY696MET8024 Prepared for : GuangXi BeiLiu JinBao Electronic Co., Ltd. Address : XinShan Industrial Zone, XiLiang Town, Beiliu City, Guangxi, China. Prepared by : EMTEK (SHENZHEN) CO., LTD. Address : Building 69, Majialong Industry Zone,Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number : ENS2305250104W00201R Date(s) of Tests : May 26, 2023 to June 18, 2023 Date of issue : June 20, 2023 $二维码$ Report No. ENS2305250104W00201R Page 2 of 65 Ver.1.0 Table of Contents 1 TEST RESULT CERTIFICATION ................................................................................................................ 3 2 EUT TECHNICAL DESCRIPTION .............................................................................................................. 5 3 SUMMARY OF TEST RESULT ................................................................................................................... 6 4 TEST METHODOLOGY .............................................................................................................................. 7 4.1 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................................................ 7 4.2 MEASUREMENT EQUIPMENT USED .......................................................................................... 7 4.3 DESCRIPTION OF TEST MODES ................................................................................................ 8 5 FACILITIES AND ACCREDITATIONS ........................................................................................................ 9 5.1 FACILITIES .................................................................................................................................... 9 5.2 EQUIPMENT.................................................................................................................................. 9 5.3 LABORATORY ACCREDITATIONS AND LISTINGS ..................................................................... 9 6 TEST SYSTEM UNCERTAINTY ............................................................................................................... 10 7 SETUP OF EQUIPMENT UNDER TEST .................................................................................................. 11 7.1 RADIO FREQUENCY TEST SETUP 1......................................................................................... 11 7.2 RADIO FREQUENCY TEST SETUP 2......................................................................................... 11 7.3 CONDUCTED EMISSION TEST SETUP ..................................................................................... 13 7.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ......................................................... 14 7.5 SUPPORT EQUIPMENT ............................................................................................................. 14 8 FREQUENCY HOPPING SYSTEM REQUIREMENTS ............................................................................ 15 8.1 STANDARD APPLICABLE .................................................................................................................. 15 8.2 EUT PSEUDORANDOM FREQUENCY HOPPING SEQUENCE ................................................................ 15 8.3 EQUAL HOPPING FREQUENCY USE ................................................................................................. 16 8.4 FREQUENCY HOPPING SYSTEM ....................................................................................................... 16 9 TEST REQUIREMENTS ........................................................................................................................... 17 9.1 20DB&99%BANDWIDTH ............................................................................................................ 17 9.2 CARRIER FREQUENCY SEPARATION ...................................................................................... 26 9.3 NUMBER OF HOPPING FREQUENCIES ................................................................................... 30 9.4 AVERAGE TIME OF OCCUPANCY (DWELL TIME) .................................................................... 32 9.5 MAXIMUM PEAK CONDUCTED OUTPUT POWER ................................................................... 34 9.6 CONDUCTED SUPRIOUS EMISSION ........................................................................................ 38 9.7 RADIATED SPURIOUS EMISSION ............................................................................................. 49 9.8 CONDUCTED EMISSION TEST ................................................................................................. 62 9.9 ANTENNA APPLICATION ............................................................................................................ 65 Report No. ENS2305250104W00201R Page 3 of 65 Ver.1.0 1 TEST RESULT CERTIFICATION Applicant : GuangXi BeiLiu JinBao Electronic Co., Ltd. Address : XinShan Industrial Zone, XiLiang Town, Beiliu City, Guangxi, China. Manufacturer : GuangXi BeiLiu JinBao Electronic Co., Ltd. Address : XinShan Industrial Zone, XiLiang Town, Beiliu City, Guangxi, China. EUT : UNDERCABINET BLUETOOTH SPEAKER WITH FM RADIO Model Name : MET8024, EKR-1000, EKT-1000, NKR-1000, MD8024 Trade Mark : MET, EMERSON, NAXA, MODERN Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C PASS IC RSS-GEN, Issue 5(04-2018)+A1(03-2019)+A2(02-2021) IC RSS-247 Issue 2(02-2017) PASS The above equipment was tested by EMTEK(SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample E…

Text truncated - open the document above for the full version.

Report No. ENS2305250104W00201R Page 43 of 65 Ver.1.0 Conducted Spurious Emission DH5_Ant1_2402_30~1000 DH5_Ant1_2402_1000~26500 DH5_Ant1_2441_30~1000 Report No. ENS2305250104W00201R Page 44 of 65 Ver.1.0 DH5_Ant1_2441_1000~26500 DH5_Ant1_2480_30~1000 DH5_Ant1_2480_1000~26500 Report No. ENS2305250104W00201R Page 45 of 65 Ver.1.0 2DH5_Ant1_2402_30~1000 2DH5_Ant1_2402_1000~26500 2DH5_Ant1_2441_30~1000 Report No. ENS2305250104W00201R Page 46 of 65 Ver.1.0 2DH5_Ant1_2441_1000~26500 2DH5_Ant1_2480_30~1000 2DH5_Ant1_2480_1000~26500 Report No. ENS2305250104W00201R Page 47 of 65 Ver.1.0 3DH5_Ant1_2402_30~1000 3DH5_Ant1_2402_1000~26500 3DH5_Ant1_2441_30~1000 Report No. ENS2305250104W00201R Page 48 of 65 Ver.1.0 3DH5_Ant1_2441_1000~26500 3DH5_Ant1_2480_30~1000 3DH5_Ant1_2480_1000~26500 Report No. ENS2305250104W00201R Page 49 of 65 Ver.1.0 9.7 RADIATED SPURIOUS EMISSION 9.7.1 Applicable Standard According to FCC Part 15.247(d), 15.205, 15.209 and KDB 558074 D01 15.247 MEAS GUIDANCE v05r02 According to IC RSS-Gen and RSS-247 9.7.2 Conformance Limit According to FCC Part 15.247(d): radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). According to FCC Part15.205, Restricted bands MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 10.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.17725-4.17775 37.5-38.25 1435-1626.5 9.0-9.2 4.20725-4.20775 73-74.6 1645.5-1646.5 9.3-9.5 6.215-6.218 74.8-75.2 1660-1710 10.6-12.7 6.26775-6.26825 123-138 2200-2300 14.47-14.5 8.291-8.294 149.9-150.05 2310-2390 15.35-16.2 8.362-8.366 156.52475-156.52525 2483.5-2500 17.7-21.4 8.37625-8.38675 156.7-156.9 2690-2900 22.01-23.12 8.41425-8.41475 162.0125-167.17 3260-3267 23.6-24.0 12.29-12.293 167.72-173.2 3332-3339 31.2-31.8 12.51975-12.52025 240-285 3345.8-3358 36.43-36.5 12.57675-12.57725 322-335.4 3600-4400 (2) 13.36-13.41 According to FCC Part15.205,the level of any transmitter spurious emission in Restricted bands shall not exceed the level of the emission specified in the following table Restricted Frequency(MHz) Field Strength (μV/m) Field Strength (dBμV/m) Measurement Distance 0.009-0.490 2400/F(KHz) 20 log (uV/m) 300 0.490-1.705 24000/F(KHz) 20 log (uV/m) 30 1.705-30 30 29.5 30 30-88 100 40 3 88-216 150 43.5 3 216-960 200 46 3 Above 960 500 54 3 9.7.3 Test Configuration Test according to clause 7.2 radio frequency test setup 2 9.7.4 Test Procedure This test is required for any spurious emission that falls in a Restricted Band, as defined in Section 15.205. It must be performed with the highest gain of each type of antenna proposed for use with the EUT. Use the following spectrum analyzer settings: For Above 1GHz: The EUT was placed on a turn table which is 1.5m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 1 MHz VBW ≥ RBW Sweep = auto Detector function = peak Report No. ENS2305250104W00201R Page 50 of 65 Ver.1.0 Trace = max hold For Below 1GHz: The EUT was placed on a turn table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 100 kHz for VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold For Below 30MHz: The EUT was placed on a turn table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 9kHz VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold For Below 150KHz: The EUT was placed on a turn table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 200Hz VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold Follow the guidelines in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization, etc. A pre-amp and a high pass filter are required for this test, in order to provide the measuring system with sufficient sensitivity. Allow the trace to stabilize. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, which must comply with the limit specified in Section 15.35(b). Submit this data. Now set the VBW to 10 Hz, while maintaining all of the other instrument settings. This peak level, once corrected, must comply with the limit specified in Section 15.209. If the dwell time per channel of the hopping signal is less than 100 ms, then the reading obtained with the 10 Hz VBW may be further adjusted by a “duty cycle correction factor”, derived from 20log(dwell time/100 ms), in an effort to demonstrate compliance with the 15.209 limit. Submit this data. Repeat above procedures until all frequency measured was complete. 9.7.5 Test Results  Spurious Emission below 30MHz(9KHz to 30MHz) Temperature: 22 ̊ C Relative Humidity: 45% ATM Pressure: 1011 mbar Freq. (MHz) Ant.Pol. Emission Level(dBuV/m) Limit 3m(dBuV/m) Over(dB) H/V PK AV PK AV PK AV -- -- -- -- -- -- -- -- Note: the amplitude of spurious emission that is attenuated by more than 20dB below the permissible limit has no need to be reported. Distance extrapolation factor =40log(Specific distance/ test distance)( dB); Limit line=Specific limits(dBuV) + distance extrapolation factor  Spurious Emission Above 1GHz(1GHz to 25GHz) Report No. ENS2305250104W00201R Page 51 of 65 Ver.1.0 All the antenna(Antenna 1) and modes(GFSK, π/4-DQPSK, 8DPSK) m…

Text truncated - open the document above for the full version.

1.1. Photos of Radiation Emission Measurement Photos of Conducted Emission Measurement Spurious Emission Test Setup (Below 1GHz) Spurious Emission Test Setup (Above 1GHz) ----------------The end----------------