A3KM118LCD Color Monitor

Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 170B4MG z 17-inch color LCD monitor with excellent display performance z Dual input - accepts DVI-D digital and VGA analog inputs z Embedded AC power supply z Front firing speakers with 2x2W RMS stereo sound output z Advanced AUTO adjustment optimizes picture quality z Rotation for both portrait and landscape display z Liner height adjustment for best viewing position z Adjustable tilt and swivel function z Optional self-powered USB hub RETURN TO TOP OF THE PAGE Technical Specifications* LCD PANEL • TypeTFT LCD • Screen size17" / 43.2cm diagonal • Pixel Pitch0.264 x 0.264mm • LCD Panel type 1280 x 1024 pixels R.G.B. vertical stripe Anti-glare polarizer, hard coated • Effective viewing area337.9 x 270.3 mm • Display Colors16M colors SCANNING Vertical refresh rate56Hz-76Hz Horizontal Frequency30kHz-82kHz VIDEO • Video dot rate135MHz • Input impedance - Video 75 ohm Installstion and Operating Instructions Exhibit 3 * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Resolution & Preset Modes - Sync 2.2K ohm • Input signal levels0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polaritiesPositive and negative • Video interface Dual input: D-Sub (analog) and DVI-D (digital) are available and user selectable AUDIO • Input signal level0.7 Vpp • Headphone out signal level 32 ohm 20+20mW • Input signal connector3.5mm mini jack • Loudspeaker 4W Stereo Audio (2W/channel RMS x2, 200 Hz-12 kHz, 8 ohm, THD=10%) MICROPHONE • Sensitivity -55dB re 1V/ubar at 1kHz • Output impedance2.2K ohm max. • Directivity -5dB at 180° • Frequency range300Hz-3kHz Optical characteristics • Contrast ratio: 400 (typ.) • Brightness: 260 cd/m 2 (typ.) • Peak contrast angle6 o'clock • White Chromatcity: x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) • Viewing Angle: (C/R>5) Upper >80° (typ.) Lower > 80° (typ.) Left > 80 ° (typ.) Right > 80 ° (typ.) • Response time <25ms (typ.) • Maximum1280 x 1024 at 75Hz • Recommended 1280 x 1024 at 60Hz RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving features: 33 user definable modes 15 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.5 640*350 70 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60.0 1024*768 75 69.0 1152*870 75 71.8 1152*900 76 63.9 1280*1024 60 80 1280*1024 75 Power Management Definition VESA Mode Video H-sync V-sync Power Used LED color ON Active Yes Yes < 40 W (typ.) Green OFF Blanked No No < 1 W Amber This monitor is E NERGY S TAR ® compliant. A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy RETURN TO TOP OF THE PAGE Physical Specifications * These information are subject to change without notice. * Resolution 1280x1024, standard size, contrast max., brightness 50%, 9300° K, full white pattern, without audio/USB. RETURN TO TOP OF THE PAGE Pin Assignment 1. The digital only connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table: efficiency. • Dimension (WxHxD) 375 x 413 x 184 mm (incl. Pedestal) • Weight 6.3 Kg • Tilt / Swivel0° ~ 35° / + - 175° • Height adjustment rang 50mm • Portrait display90° rotation counter clockwise • Power supply100 — 240 VAC, 50/60 Hz • Power consumption 40 W* (typ.) • Temperature 5° C to 35° C (operating) -20° C to 60° C (storage) • Relative humidity 20% to 80% • System MTBF50K hrs (including CCFL 40K hrs) Pin No. Signal Assignment Pin No. Signal Assignment Pin No. Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1-17T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+18T.M.D.S. Data0+ 3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield 4 No connect 12 No connect 20No connect 5 No connect 13 No connect 21No connect 6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data 15 Ground (for +5V)23T.M.D.S. Clock+ 2. The 15-pin D-sub connector (male) of the signal cable: RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Front View Product Description 8 No connect 16 Hot Plug Detect24T.M.D.S. Clock- Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V 2 Green video input/SOG 10 Logic ground 3 Blue video input 11 Identical output - connected to pin 10 4 Sense (GND) 12 Serial data line (SDA) 5 Not connected 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Physical Function 1) Tilt 2) Swivel 3) Height adjustment 4) Portrait display Turn monitor from landscape view to portrait view 4.1) Tilt the monitor body at an angle 4.2) Rotate the monitor body 90 degrees counter clockwise. Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance • Accessories (optional) Front View Product Description UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. Signal inputs selective hotkeys. Allows user to switch between two video connectors (D-Sub & DVI-D) BRIGHTNESS hotkey. When the UP and DOWN a…

Text truncated - open the document above for the full version.

Exhibit 4 Brief Description of Circuit Functions Function Description for Hudson-170B4 1. General The Hudson 170B4 SXGA TFT LCD monitor is specified as a display peripheral with analog (DSUB) and digital (DVI_D). Horizontal scan range is 30KHz-82KHz and the refresh range is 56Hz-76Hz in normal mode. This scan range allows it to display resolution up to 1280x1024x75Hz non-interlace input. The image can be adjusted by OSD control. These adjustments can be stored in an onboard memory. 2. Power supply Main voltage : AC 90-264Vrms, 50-60Hz Power consumption : 45W Max.(with audio) Power indicator : LED(ON: green, standby: amber) Auto power saving : VESA DPMS 3. Input signal Horizontal scan : 30-82KHz Vertical scan : 56-76Hz(from VGA to SXGA for analog/digital), Input signals : A. D-SUB signal input level Video : 0.7Vp-p linear/75 ohms Sync : H/H+V,V TTL level, composite sync, sync on green B. Intel DVI-D digital Single channel TMDS signal 4. OSD( On Screen Display) function Software control function via OSD -Main controls: Language----------------- 6 languages. Brightness & Contrast-- Brightness, Contrast Adjust color-------------- Original panel color, 9300K, 6500K, sRGB, User preset OSD Settings------------- Horizontal,Vertical Product information----- Serial No, Resolution, Signal input Input selection------------Analog(D-SUB), Digital(DVI-D), Reset to factory setting-- No/Yes Exit Main controls 5. LCD Panel Type : 17” TFT LCD flat panel Dimensions : 17”(358.5 x 296.5 x 19 mm) Pitch : 0.264mmx0.264mm Color pixel arrangement : RGB vertical stripes Number of color : 64 gray level (6 bits) Backlight : 4 CCFL’s Active area (W*H) : 337.92 x 270.5mm 6. Function block Scaler GM5126 (contains following functions): (1) Analog RGB input - Support up to SXGA 75Hz - On chip high-performance PLLs - High speed triple ADC (2) TMDSRx input - Convert serial digital signal to parallel digital RGB signal, it can reduce EMI. (3) Format converter - Built in GPIO port, mode detection. - Convert the image data from ADC, TMDSRx or Video Decoder to LCD panel data format. - Zoom the input video to full screen display. - High quality zoom and shrink scaling engine (4) RXDS - Convert digital image signal to RSDS signal, it can reduce EMI. (5) On-Screen display (OSD) controller (6) On-chip microcontroller (OCM) (7) Programmable OnPanel timing Controller (TCON) Inverter - Accept +12VDC voltage. - Provide 680Vrms voltage for CCFL. Power supply - AC adapter : AC power input (from 90VAC to 264VAC) can generate +12VDC, and +5VDC power - DC to DC converter : Convert +12V to +3.3VDC power. Hudson 170B4 CIRCUIT ARCHITETURE AC 90 ~260V TFT LCD MODULE DDC_A M24C02 DVI Connecto r DSUB Connector 30 Pin Connector DDC_D M24C02 Power Board AC ADPTER (+12V) CLK: 70 ~ 120KHz Control Board KEY & LED RX0 ~RX2, RXC R G B Input Regulator IRU1206 Schmitt 74LC14APW- T TCON Signal EEPROM M24C16 FLASH M29W010 Data Address Gm5126 Ultra-Reliable DVI RX Triple ADC and PLL 8051 Micro- Controller Panel Timing Control RSDS TX Front RGB RSDS Back RGB RSDS HS and VS 3.3V 3.3V 2.5V AU 5V/CPT 3.3Vand 12V Clock 14M318Hz Brightness/BL-EN Panel Power MOSFET Switch 12V/5V/3.3V Panel Control Signal Reset IC SA56616- 28 Control Signal DC_DC Converter (+12V,+5V, +3.3V) 50 Pin Connector INVERTER BOARD DC-AC INVERTER Exhibit 5 Block Diagram

Exhibit 7 Photographs Front View Rear View Label

Exhibit 2 FCC ID Label

Assembly w/o Front Cabinet Assembly w/o Back Cover (AU Panel) Shielding Cover (AU Panel) Assembly w/o Shielding Cover (AU Panel) PCB Layout (AU Panel) PCB Layout (AU Panel) Plate (AU Panel) LCD Panel (AU Panel) Assembly w/o Back Cover (QDI Panel) Shielding Cover (QDI Panel) Assembly w/o Shielding Cover (QDI Panel) PCB Layout (QDI Panel) PCB Layout (QDI Panel) PCB Layout (QDI Panel) PCB Layout (QDI Panel) Plate (QDI Panel) LCD Panel (QDI Panel) Audio Base assembly PCB Layout PCB Layout Power Cord and I/F Cables

Philips Electronics Industries (Taiwan) Ltd - EMC Lab. 5, Tze Chiang 1 Road, Chungli Industrial Park, Chungli, Taoyuan, Taiwan Tel.: +886-3-454-9862 Fax.: +886-3-454-9887 E-mail: [email protected] FCC Test Report Report No.: TYR87-2039 Date : 24 January, 2003 Page : Page 1 of 60 Customer : Philips Electronics Industries Name : Mr. S.T. Huang – EE LCD Address : 5, Tze Chiang 1 Road, Zip/City : Chungli Industrial Park, Country : Chungli, Taiwan, R.O.C. Equipment Under Test (including peripherals) : FCC ID. : A3KM118 Model Name : 170B4 Serial Number : TY0211692(AU panel), TY0212779(QDI panel) Description : 17” SXGA LCD color monitor, Max. resolution 1280x1024/75Hz EMC Standards : FCC Part 15 of October 01,1999 Class B ANSI C63.4-1992 Result : PASSED the limits/test-levels in the standards. Note : The results in this report apply only to the sample(s) and mode(s) tested. It is the manufacturer’s responsibility to assume the continued EMC compliance of production models. Date of receipt of EUT : 10 Jan. 2003 Date of performance of test : 11 Jan., 2003 to 20 Jan., 2003 NVLAP Signatory Philips Electronics Industries (Taiwan) Ltd This report shall not be reproduce except in full, without written approval of the testing laboratory C.C. Wu - EMC Test Engineer Ronnie Yang - EMC Manager Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 2 of 60 Table of contents 1. Summary of test results.............................................................................3 2. General information of EUT.......................................................................4 3. Test equipment.......................................................................................5 4. Test configuration of EUT and peripherals......................................................6 5. Test procedure.......................................................................................7 6. Measurement uncertainty...........................................................................9 7. Conducted emissions test..........................................................................10 8. Radiated emissions test............................................................................35 9. Photographs of test set-up.........................................................................56 10. References...........................................................................................60 Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 3 of 60 1. Summary of test results Test Standard Result Note Emission, ANSI C63.4-1992 Conducted emission Radiated emission FCC Part 15 FCC Part 15 Passed Passed Remark: The test sample fully complies with the requirements set forth in : FCC Part 15 Class B. Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 4 of 60 2. General Information of EUT The EUT, 17” color monitor : Model No. : 170B4 FCC ID : A3KM118 Brand : PHILIPS The color monitor automatically scans horizontal frequencies between 30KHz and 82KHz , and vertical frequencies between 56Hz and 76Hz. This color monitor displays sharp and brilliant images of text and graphics with a maximum resolution up to 1280x1024 pixels. The monitor has 16 factory-preset modes as indicated in the following table: # Resolution H-Frequency Pixel rate V-Frequency Comment 1 640X350 31.5KHz 25.175 70Hz IBM VGA 10h 2 720X400 31.5KHz 28.322 70Hz IBM VGA 3h 3 640X480 37.5KHz 31.501 75Hz 4 640X480 35.0KHz 30.24 67Hz 5 640X480 31.5KHz 25.175 60Hz 6 800X600 35.2KHz 36 56Hz 7 800X600 46.9KHz 49.498 75Hz 8 800X600 37.9KHz 40 60Hz 9 832X624 49.7KHz 57.28 75Hz MAC 10 1024X768 60.0KHz 78.75 75Hz 11 1024X768 48.4KHz 65 60Hz 12 1152X870 68.7KHz 100 75Hz MAC 13 1152X900 71.8KHz 108 76Hz SUN Mode II 14 1280X1024 64.0KHz 108 60Hz 15 1280X1024 80.0KHz 135 75Hz 16 688X556 31.3KHz 27 50Hz TV-PAL Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 5 of 60 3. Test Equipment Test equipment used for line Conducted and Radiated emissions as following. All equipment were calibrated according to ANSI C63.4-1992 and ISO-9000 requirement unless otherwise specified. Traceability to R.O.C. and international standards is assured by using calibrated all equipment. - For Conducted Emissions Test: Test Equipment Model No. Serial No. Last Calibrate Next Calibrate Spectrum HP8568B 2928A04640 06/27/2002 06/27/2003 EMI Receiver R & S ESVS30 841977/006 06/13/2002 06/13/2003 LISN EMCO 3825/2 9311-2153 06/13/2002 06/13/2003 LISN EMCO 3825/2 9311-2154 06/13/2002 06/13/2003 RF Cable 8-meter N/A 05/29-2002 05/29/2003 - For Radiated Emissions Test: Test Equipment Model No. Serial No. Last Calibrate Next Calibrate Spectrum HP8568B 2928A04640 06/27/2002 06/27/2003 RF Preselector HP85685A 2620A00338 06/27/2002 06/27/2003 QP Adapter HP85650A 2811A01324 06/27/2002 06/27/2003 EMI Receiver R & S ESVS30 841977/006 06/13/2002 06/13/2003 Biconical Antenna EMCO 3110B 3222 06/04/2002 06/04/2003 Biconical Antenna EMCO 3110B 3224 06/04/2002 06/04/2003 Log-Periodic Antenna EMCO 3146A 1424 06/04/2002 06/04/2003 Log-Periodic Antenna EMCO 3146A 1425 06/04/2002 06/04/2003 Turn Table EMCO 1060 1068 05/27/2002 05/27/2003 Antenna Tower EMCO 1050 1113 05/27/2002 05/27/2003 RF Cable M17/75-RG214-NE N/A 05/27/2002 05/27/2003 Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 6 of 60 4. Test Configuration of EUT and Peripherals The system was configured for testing in a typical fashion ( as a customer would normally use it ) according to ANSI C63.4-1992, please see the photographs for detail. For system measurement, the EUT “170B4” were connected to: Description Brand/ Model No. Serial No. FCC ID Remark A Monitor PHILIPS 170B4 TY0211692 (AU) TY0212779 (QDI) A3KM118 EUT B PC Compaq ENC P866 5K15FXHZ2013 FCC Logo C Keyboard Compaq KB-9963 B26950GGALP13Q FCC…

Text truncated - open the document above for the full version.

Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 56 of 60 9. Photographs of Test Set-up Conducted Emissions Test Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 57 of 60 Conducted Emissions Test Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 58 of 60 Radiated Emissions Test Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 59 of 60 Radiated Emissions Test Reference: TYR87-2039 170B4 Date: 24 January 2003 Philips Electronics Industries (Taiwan) Ltd Page: 60 of 60 10. Reference FCC part 15 - 1999 Radio frequency device. ANSI C63.4-1992, “American national standard for measurement of radio-noise emission from low-voltage electrical and electronic equipment in the range of 9KHz to 40GHz”