A3KM147LCD Monitor

Page 1 of 1e-Manual Product Information Product Features 230WP7NS z Designed for maximum productivity {Big, widescreen ideal for viewing two A4 pages side-by-side {90 degree screen rotation and smart cable management {Designed for 'just-right' height and angle adjustment z Best total cost of ownership solution {SmartManage compatibility enables LAN-based asset management {Power consumption below the industry average z Outstanding front of screen performance {WUXGA, wide format 1920x1200 resolution for sharper display {Widest viewing angle up to 176 degrees {Dual input accepts both analog VGA and digital DVI signals z Great convenience {Built-in High-speed USB 2.0 solution for easy connections {Easy to adjust display settings with Philips SmartControl {Embedded power supply eliminates external power adaptors RETURN TO TOP OF THE PAGE Technical Specifications* LCD PANEL • TypeTFT LCD • Screen size23.0" / 58.4cm • Pixel Pitch0.258 x 0.258mm • LCD Panel type 1920 x 1200pixels R.G.B. vertical stripe Anti-glare polarizer, hard coated • Effective viewing area495.36 x 309.6mm • Display Colors8 bits interface (16M colors) SCANNING Vertical refresh rate56Hz-85Hz (Analog / Digital input) Horizontal Frequency30kHz-94kHz (Analog input) VIDEO • Video dot rate202.5 MHz • Input impedance - Video 75 ohm - Sync 2K2 ohm Page 1 of 9Product Information * This data is subject to change without notice. RETURN TO TOP OF THE PAGE Resolution & Preset Modes • Input signal levels0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polaritiesPositive and negative Optical characteristics • Contrast ratio: 800:1 (typ). • Brightness: 300 cd/m 2 (typ.) • Peak contrast angle6 o'clock • White Chromaticity: x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) • Viewing Angle: (C/R>10) Upper >89° (typ.) Lower > 89° (typ.) Left > 89° (typ.) Right > 89° (typ.) • Response time 12 ms (typ.) • Maximum 1600 x 1200 at 75Hz(analog input) 1600 x 1200 at 60Hz(digital input) • Recommended 1920 x 1200 at 60Hz * at DVI digital input 37 user definable modes 15 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.5 640*350 70 (IBM VGA 10h) 31.5 720*400 70 31.5 640*480 60 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 48.4 1024*768 60 60.0 1024*768 75 60 1280*960 60 69.0 1152*870 75 Page 2 of 9Product Information RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will be waken up automatically by your PC. The following table shows the power consumption and signaling of this automatic power saving feature: RETURN TO TOP OF THE PAGE Physical Specifications 63.9 1280*1024 60 80.0 1280*1024 75 75.0 1600*1200 60 93.8 1600*1200 75 (Analog only) 74.5 1920*1200 60 (Analog only) 74 1920*1200 60 Power Management Definition VESA Mode Video H-sync V-sync Power Used LED color Active ON Yes Yes < 90W Green Sleep OFF No No < 2W Amber Switch Off OFF- -< 2WOFF • Dimension (WxHxD) 548 x 422.6 x 234.6 mm (incl. Pedestal) (in lowest position) • Weight 11.8 Kg • Tilt / Swivel-5° ~ 25° / ± 45° • Height adjustment rang 130 mm • Power supply100— 240 VAC, 60 - 50 Hz • Power consumption 80 W* (typ.) • Temperature 5° C to 35° C (operating) -20° C to 60° C (storage) • Relative humidity 20% to 80% • System MTBF50K hrs (excluding CCFL 40K hrs) Page 3 of 9Product Information * This data is subject to change without notice. * Resolution 1920 x 1200, standard size, contrast max., brightness 50%, 6500° K, full white pattern. RETURN TO TOP OF THE PAGE Pin Assignment 1. The DVI connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table: 2. The 15-pin D-sub connector (male) of the signal cable: • Cabinet color Black/Silver • Altitude - storage/shipment - operating 0 - 40,000 feet (12,192m) 0 - 12,000 feet (3657.6m) Pin No. Signal Assignment Pin No. Signal Assignment Pin No. Signal Assignment Pin No. Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1-17T.M.D.S. Data0-C1* Analog R 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+18T.M.D.S. Data0+C2* Analog G 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield C3* Analog B 4 NC 12 NC20NCC4* Analog H-syn 5 NC 13 NC21NCC5 * Analog GND (Analog R, G, return) 6 DDC Clock 14 +5V22 T.M.D.S. Clock Shield 7 DDC Data 15 Ground (return for +5V and H/V- sync) 23T.M.D.S. Clock+ 8 * Analog V-sync16 Hot Plug Detect24T.M.D.S. Clock- Page 4 of 9Product Information RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Front View Product Description RETURN TO TOP OF THE PAGE Physical Function Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V 2 Green video input/SOG 10 Ground 3 Blue video input 11 Ground 4 Ground 12 Serial data line (SDA) 5 Cable detect 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground Page 5 of 9Product Information 1) Tilt 2) Swivel 3) Height adjustment Page 6 of 9Product Information 4) Portrait display Page 7 of 9Product Information Page 8 of 9Product Information RETURN TO TOP OF THE PAGE Page 9 of 9Product Information Installing Your LCD Monitor Front View Product Description RETURN TO TOP OF THE PAGE Rear View 1 To switch monitor's power On and Off 2 To access OSD menu 3 To adjust the OSD 4 To adjust brightness of the display 5 To adjust the OSD 6 AUTO Automatically adjust the horizontal position, vertical position , phase and clock setting Page 1 of 2Installing Your LCD Monitor RETURN TO TOP OF THE PAGE Optimizing Performance zFor best performance, ensure that your display settings are set at 1920 x 1200 @60Hz zYou can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the bes…

Text truncated - open the document above for the full version.

1 230WP7 Scalar Board Block Diagram 230WP7 Scalar Board Block Diagram • To use M-star Scalar MCU NT68F631A DDR K4D263238A Dsub DVI_A DVI_D LVDS RGB/Hsync/ Vsync) E 2 PROM M24C16 Specification : 2 x Analog : 1600 x 1200 / 75Hz 1 x Digital : 1600 x 1200 / 60Hz Specification : 2 x Analog : 1600 x 1200 / 75Hz 1 x Digital : 1600 x 1200 / 60Hz DC to DC 5V 3.3V2.5V1.8V Panel Panel Vcc LPL:18V MST9251A for 2A + 1D Circuit Description General 230WP7NS is the 7 th generation of Hudson series Flat Panel Display Monitor. It designed with LVDS interface feature. The monitor featured with DVI-I and analog signal input interface, and modularized as a display unit with embedded universal AC power supplies inside monitor main body. The monitor comes with super ergo base (SEB), the base is featured with tilt, swivel, height adjustment and portrait functionality. The power button and display control buttons (tact switch type) are on the front of the monitor. The monitor will be TCO03/TCO99 and Energy Star compliant and incorporate energy saving features described further in this document. The monitor shall support an internal scalar to automatically enable the monitor to display lower resolution video modes into 1600x1200 full screen display. The monitor shall communicate display data to the host computer using DDC2B and shall support EDID structure 1.3 for analog and digital signal input. 1. Power supply Main Voltage: AC 90 - 135 Vrms and 170 – 264 Vrms, 50/60 ± 2 Hz Power consumption: Operating < 90W, Standby < 2W. DC power switch off < 2W. Power cord length: 1.8M Power cord type: 3 lead with earth plug Power indicator: LED (ON: blue, Standby: amber) Auto power saving: EPA, Nutek, VESA, DPMS, E2000 3. Input signal Horizontal scan: 30 - 94 KHz Vertical scan: 56 -85 Hz Input signals 1).VESA Analog Input signal : Video, Hsync., Vsync Video : 0.7 Vp-p, input impedance, 75 ohm @DC Sync. : Separate sync TTL level , input impedance 5k ohms Hor. sync Positive/Negative Ver. sync Positive/Negative 2).Intel DVI Digital Input signal : Four channel TMDS signals 4. OSD (On Screen Display) function Software control function via OSD/ Control as below: Analog Signal Input 1 st LEVEL 2 nd LEVEL 3rd LEVEL MONITOR SETUP Exit Brightness & Contrast Brightness Contrast Color Original Color, 9300K,6500K, sRGB, User Define Position & Size Horizontal Vertical Size Full Screen Native Mode Fill with Aspect Input Selection Analog(D-Sub), Analog(DVI-A), Digital(DVI-D) Language English, Espanol, Frencais, Deutsch, Italiano, Simplified Chinese Phase/ Clock Phase Clock More Settings OSD Settings Horizontal Vertical Reset No Yes Serial No.: (Serial No.) Timing Mode Up/Down to Move, ok to Confirm Digital Signal Input 1 st LEVEL 2 nd LEVEL 3rd LEVEL MONITOR SETUP Exit Brightness & Contrast Brightness Contrast Color Original Color, 9300K,6500K, sRGB, User Define Size Size Full Screen Native Mode Fill with Aspect Input Selection Analog(D-Sub), Analog(DVI-A), Digital(DVI-D) Language English, Espanol, Frencais, Deutsch, Italiano, Simplified Chinese Phase/ Clock(Grey out) More Settings OSD Settings Horizontal Vertical Reset No Yes Serial No.: (Serial No.) Timing Mode Up/Down to Move, ok to Confirm 5. LCD panel Type NR. : LM230WU3-SLB1 Outside dimensions : 523.4(H) ∗ 335.6(V) ∗ 41.0(D) (Typ) mm Pixel Pitch ( mm ) : 0.258 mm x 0258mm Color pixel arrangement : RGB vertical stripes Display surface : low reflection, antiglare with hard coating Color depth : 16.7M colors (8 bits) Backlight : Six CCFL‘s Active area(WxH) : 495.36x309.60mm (23” diagonal) View angle : Horizontal & Vertical 178 degree (CR>=10) Contrast ratio : 700 :1 (typ) White luminance : Panel original color >250nits (min), 300 nits (Typ) 6. Function block 6.1 Scaler board Scaling MST9251A including ADC, Scaler, OSD, LVDS) Analog - Monitor the input horizontal and vertical sync signal to judge input video mode - Sample the input video signal according to its pixel rate to form a digital data for panel. - Auto-adjustment for sampling phase and frequency, picture alignment and color alignment. - Send the parameters to format scaler IC according to the input mode. - Process the control data listed in OSD section. Digital - Monitor DVI input with internal TMDS receiver to judge input video mode - Sample the input video signal according to its pixel rate to form a digital data for panel. - Send the parameters to format scaler IC according to the input mode. - Process the control data listed in OSD section. MCU NT68F631A - Control Scaling and all I/Os port of monitor including audio. - Store the source code into internal Flash ROM and capable of down loading program via ISP. 6.2 Front panel switch control board - Used for OSD function and power on/off 7 push buttons (left, ok, right, up, down, auto, power switch) - Power on/off LED indicator 6.3 AC to DC Power Board The AC power input from 90 VAC to 264 VAC, can generate 5Vand 18 VDC power to supply to inverter function and scaler board.

Page 1 of 9 Exhibit 7 Photographs Front View Rear View Page 2 of 9 Label Rear View w/o Base

Exhibit 2 FCC ID Label Page 2 of 9 Label Rear View w/o Base

Page 3 of 9 Rear View w/o Back Cover Shielding Cover Page 4 of 9 Assembly w/o Shielding Cover PCB Layout Page 5 of 9 PCB Layout PCB Layout Page 6 of 9 PCB Layout PCB Layout Page 7 of 9 PCB Layout Assembly w/o PCB Page 8 of 9 Plate LCD Panel Page 9 of 9 Power Cord and I/F Cables

FCC ID. A3KM147 Page 1 of 60 Audix Corporation. Report No. EM-F940250 APPLICATION FOR CERTIFICATION On Behalf of Philips Electronics Industries (Taiwan) Ltd. Flat Panel Color Monitor Model No.230WP7 FCC ID : A3KM147 Brand : PHILIPS Prepared for : Philips Electronics Industries (Taiwan) Ltd. 5, Tze Chiang 1 Road, Chungli Industrial Park Chungli, Taoyuan, Taiwan, R.O.C. Prepared By : Audix Corporation Technical Division EMC Department No. 53-11, Tin-Fu Tsun, Lin-Kou, Taipei County, Taiwan, R.O.C. Tel : (02) 2609-9301, 2609-2133 Fax : (02) 2609-9303 File Number : EM941190 Report Number : EM-F940250 Date of Test : Oct. 21 ~ 25, 2005 Date of Report : Oct. 28, 2005 FCC ID. A3KM147 Page 2 of 60 Audix Corporation. Report No. EM-F940250 TABLE OF CONTENTS Description Page Test Report Certification........................................................................................................................3 1. GENERAL INFORMATION..........................................................................................................4 1.1.Description of Device ................................................................................................................................ 4 1.2.Tested Supporting System Details............................................................................................................. 5 1.3.Description of Test Facility ....................................................................................................................... 7 1.4.Measurement Uncertainty.......................................................................................................................... 7 2. CONDUCTED EMISSION MEASUREMENT ............................................................................8 2.1.Test Equipment.......................................................................................................................................... 8 2.2.Block Diagram of Test Setup .................................................................................................................... 8 2.3.Conducted Emission Limit (15.107(a), Class B) ..................................................................................... 8 2.4.EUT’s Configuration during Compliance Measurement ...........................................................................9 2.5.Operating Condition of EUT ..................................................................................................................... 9 2.6.Test Procedure ......................................................................................................................................... 10 2.7.Test Results.............................................................................................................................................. 10 3. RADIATED EMISSION MEASUREMENT...............................................................................31 3.1.Test Equipment........................................................................................................................................ 31 3.2.Block Diagram of Test Setup .................................................................................................................. 31 3.3.Radiation Limit (15.109/CISPR 22, Class B)........................................................................................ 33 3.4.EUT’s Configuration during Compliance Measurement ......................................................................... 33 3.5.Operating Condition of EUT ................................................................................................................... 33 3.6.Test Procedure ......................................................................................................................................... 33 3.7.Radiated Emission Measurement Results................................................................................................ 34 4. DEVIATION TO TEST SPECIFICATIONS ..............................................................................52 5. PHOTOGRAPHS...........................................................................................................................53 5.1.Photos of Conducted Emission Measurement ......................................................................................... 53 5.2.Photos of Radiated Emission Measurement at Simple Anechoic Chamber (30-1000MHz) ................... 55 5.3.Photos of Radiated Measurement at Open Area Test Site (30-1000MHz).............................................. 57 5.4.Photos of Radiated Measurement at Open Area Test Site (1-2GHz) ...................................................... 59 FCC ID. A3KM147 Page 3 of 60 Audix Corporation. Report No. EM-F940250 TEST REPORT CERTIFICATION Applicant Philips Electronics Industries (Taiwan) Ltd. Factory #1 Philips Consumer Elec. Co. of Suzhou Ltd. Factory #2 TPV Electronics (Fujian) Co., Ltd EUT Description Flat Panel Color Monitor FCC ID A3KM147 (A) MODEL NO. 230WP7 (B) SERIAL NO. TY0405310 (C) BRAND PHILIPS (D) POWER SUPPLY AC 100-240V, 60-50Hz (E) TEST VOLTAGE AC 120V/60Hz Measurement Procedure Used: FCC CFR 47 Part 15 Subpart B/Sep. 2005 and CISPR 22/1997 ANSI C63.4-2003 The device described above was tested by AUDIX Corporation to determine the maximum emission levels emanating from the device. The maximum emission levels were compared to the FCC Part 15 Subpart B with the provisions of section 15.107 (a) and 15.109 (a)(g) Class B limits both conducted and radiated emission. The measurement results are contained in this test report and AUDIX Corporation is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT to be technically compliance with the FCC official limits. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of AUDIX Corporation. Date of Test : Oct. 21 ~ 25, 200…

Text truncated - open the document above for the full version.

FCC ID. A3KM147 Page 53 of 60 Audix Corporation. Report No. EM-F940250 5. PHOTOGRAPHS 5.1. Photos of Conducted Emission Measurement Test Mode: D-Sub or DVI Input, Panel Position: 0°/Horizontal FRONT VIEW OF CONDUCTED MEASUREMENT BACK VIEW OF CONDUCTED MEASUREMENT FCC ID. A3KM147 Page 54 of 60 Audix Corporation. Report No. EM-F940250 Test Mode: DVI Input, Panel Position: 90°/Vertical FRONT VIEW OF CONDUCTED MEASUREMENT BACK VIEW OF CONDUCTED MEASUREMENT FCC ID. A3KM147 Page 55 of 60 Audix Corporation. Report No. EM-F940250 5.2. Photos of Radiated Emission Measurement at Simple Anechoic Chamber (30-1000MHz) Test Mode: D-Sub or DVI Input, Panel Position: 0°/Horizontal FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. A3KM147 Page 56 of 60 Audix Corporation. Report No. EM-F940250 Test Mode: D-Sub Input, Panel Position: 90°/Vertical FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. A3KM147 Page 57 of 60 Audix Corporation. Report No. EM-F940250 5.3. Photos of Radiated Measurement at Open Area Test Site (30-1000MHz) Test Mode: 1280*1024/75Hz, 80kHz, DVI Input, Panel Position: 0°/Horizontal FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. A3KM147 Page 58 of 60 Audix Corporation. Report No. EM-F940250 SETUP WITH MAXIMUM DETECTED EMISSION AT HORIZONTAL POLARIZATION SETUP WITH MAXIMUM DETECTED EMISSION AT VERTICAL POLARIZATION FCC ID. A3KM147 Page 59 of 60 Audix Corporation. Report No. EM-F940250 5.4. Photos of Radiated Measurement at Open Area Test Site (1-2GHz) FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. A3KM147 Page 60 of 60 Audix Corporation. Report No. EM-F940250