ADB9ZWRTR110Marine Radar

MARINE RADAR FAR-1467DS FAR-1467DS-BB OPERATOR'S MANUAL www.furuno.com MODEL The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A:0000 Printed in Japan All rights reserved. Z:MAR.30, 2012 Pub. No.OME-36120-Z *00017580410**00017580410* (DAMI)FAR-1467DS/1467DS-BB *00017580410**00017580410* * 0 0 0 1 7 5 8 0 4 1 0 * i Ni-CdPb IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications can change without notice. • The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings. • Save this manual for future reference. • Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty. • All brand and product names are trademarks, registered trademarks or service marks of their respective holders. How to discard this product Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal. How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit. In the European Union The crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU. In the USA The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws. In the other countries There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycling symbols in the future. Cd ii Mandatory Action Prohibitive Action WARNING CAUTION Warning, Caution WARNING Radio Frequency Radiation Hazard The operator must read the safety instructions before attempting to operate the equipment. The radar antenna emits electromagnetic radio frequency (RF) energy that can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmitting antenna at a close distance. Distances at which RF radiation level of 100, 50 and 10 W/m 2 are given in the table below. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. 100W/m 2 ModelAntenna 10W/m 2 FAR-1467DS SN24AF SN30AF 0.6 m 0.5 m 8.5 m 7.7 m SAFETY INSTRUCTIONS iii WARNING WARNING WARNING Do not open the equipment. The equipment uses high voltage that can cause electrical shock. Refer any repair work to a qualified technician. Before turning on the radar, be sure no one is near the antenna. Prevent the potential risk of being struck by the rotating antenna, which can result in serious injury or death. If water leaks into the equipment or something is dropped into the equipment, immediately turn off the power at the switchboard. Fire or electrical shock can result. If the equipment is giving off smoke or fire, immediately turn off the power at the switchboard. Fire or electrical shock can result. If you feel the equipment is acting abnormally or giving off strange noises, immediately turn off the power at the switchboard and contact a FURUNO service techni- cian. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Make sure no rain or water splash leaks into the equipment. Fire or electrical shock can result if water leaks into the equipment. Do not place liquid-filled containers on or near the equipment. Fire or electrical shock can result if a liquid spills into the equipment. Do not operate the equipment with wet hands. Electrical shock can result. Keep objects away from the open-n- type antenna unit, so as not to impede rotation of the antenna. Fire, electrical shock or serious injury can result. Use the proper fuse. Use of the wrong fuse can cause fire or electrical shock. Do not depend on one navigation device for the navigation of the ship. The navigator must check all aids available to confirm position. - The TT automatically tracks an automatically or manually acquired radar target and calculates its course and speed, indicating them with a vector. Since the data generated by the TT depends on the selected radar targets, the radar must be optimally tuned for use with the TT, to ensure required targets will not be lost or unnecessary targets like sea returns and noise will not be acquired and tracked. - A target is not always a landmass, reef, ship, but can also be returns from the sea surface and from clutter As the level of clutter changes with the environment, the operator must correctly adjust the sea and rain clutter controls and the gain control so that the target echoes do not dis- appear from the radar screen. iv TABLE OF CONTECTS FOREWORD...........................................…

Text truncated - open the document above for the full version.

Installation Manual MARINE RADAR FAR-1467DS/1467DS-BB SAFETY INSTRUCTIONS.................................................................................................................... i SYSTEM CONFIGURATION .............................................................................................................. iii EQUIPMENT LISTS ........................................................................................................................... iv 1. MOUNTING .....................................................................................................................................1 1.1 Antenna Unit ............................................................................................................................8 1.2 Control Unit..............................................................................................................................8 1.3 Processor Unit .......................................................................................................................10 1.4 Power Supply Unit ................................................................................................................. 11 2. WIRING .........................................................................................................................................12 2.1 Interconnection ......................................................................................................................12 2.2 Antenna Unit ..........................................................................................................................13 2.3 Processor Unit .......................................................................................................................18 2.4 Power Supply Unit .................................................................................................................23 2.5 Changing AC Power Specification of Processor Unit .............................................................25 2.5.1 Processor Unit ......................................................................................................25 2.5.2 Power Supply Unit ................................................................................................26 2.6 Interswitch..............................................................................................................................27 2.7 Connection to CAN bus Network ...........................................................................................28 3. SETTING AND ADJUSTMENT......................................................................................................29 3.1 Setting Initial Setting Wizard ..................................................................................................29 3.2 Initializing Tuning...................................................................................................................43 3.3 Adjustment of Video Level .....................................................................................................44 3.4 Heading Alignment.................................................................................................................45 3.5 Adjustment of Sweep Timing.................................................................................................. 46 3.6 Suppressing Main Bang.........................................................................................................47 3.7 Gyrocompass Signals ............................................................................................................48 4. Input Signal....................................................................................................................................54 4.1 NMEA Input Sentence............................................................................................................54 4.2 NMEA Output Sentence.........................................................................................................56 4.3 CAN bus port Input/output .....................................................................................................57 PACKING LISTS.............................................................................................................................. A-1 OUTLINE DRAWINGS .................................................................................................................... D-1 INTERCONNECTION DIAGRAMS.................................................................................................. S-1 All brand and product names are trademarks, registered trademarks or service marks of their respective holders. www.furuno.com The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A:0000 Printed in Japan All rights reserved. Z:MAR.27, 2012 Pub. No.IME-36120-Z *00017580810**00017580810* (HIMA)FAR-1467DS/1467DS-BB *00017580810**00017580810* * 0 0 0 1 7 5 8 0 8 1 0 * i Wear a safety belt and hard hat when working on the antenna unit. Serious injury or death can result if someone falls from the radar antenna mast. DANGER WARNING The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmitting antenna at a close distance. Distances at which RF radiation levels of 100 W/m 2 and 10 W/m 2 exist are given in the table below. Note: If the antenna unit is installed at a close distance in front of the wheel house, it may be necessary to halt transmission within a certain sector of antenna revolution. This can be done from the SCANNER menu. Radio Frequency Radiation Hazard Distance to 100 W/m 2 point Distance to 10 W/m 2 point Radiator type SN24AF SN30AF 0.6 m 0.6 m 8.5 m 7.7 m SAFETY INSTRUCTIONS The installer must read and follow all the …

Text truncated - open the document above for the full version.

Federal Communications Commission Office of Engineering and Technology 445 12th Street, SW Washington, DC 20554 Request for Confidentiality Dear Sir or Madam, In regard to the FCC application for ID ADB9ZWRTR110 The following documents are company confidential, containing technical information of a proprietary nature. Circuit Diagrams/Schematics Operational Description I respectfully request that documents of this category be kept confidential. Thank you for your assistance. Best regards, Shane Ryan Type Acceptance Commercial Service FURUNO USA Inc. (360) 834-9300 X5060 (360) 834- 833-5195 [email protected]

8/17/12 Federal Communications Commission Office of Engineering and Technology 445 12th Street, SW Washington, DC 20554 To whom it may concern, We hereby respectfully request that under the provision of FCC rules section0.457(d) and0.459, the following documents submitted in support of this application for ADB9ZWRTR110 certification be provided with confidential status. Schematics Parts list/Tune up info Operational description These documents contain trade secrets that are treated as confidential by us. Substantial competitive harm to our company business could result should they be made available to the public. Best regard Shane Ryan Type Acceptance Commercial Service FURUNO USA Inc. (360) 834-9300 X5060 (360) 834- 833 -5195 [email protected]

 Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 1 of 10 - 1 Photographs of Furuno Radar FAR-1467DS (Transceiver type: RTR-110) Outside View 1.1 Antenna Unit (with Scanner unit RSB-132 (including Transceiver RTR-110 and Radiator SN-36AF) 1.1.1 Front View  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 2 of 10 - 1.1.2 Rear View  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 3 of 10 - 1.1.3 Rear View of Scanner (with ID Label attached on the Scanner Unit)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 4 of 10 - 1.1.4 ID Label (Name Plate)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 5 of 10 - 1.2 Processor Unit RPU-021 1.2.1 Top View (showing ID Label on Top Cover)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 6 of 10 - 1.2.2 Rear View  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 7 of 10 - 1.2.3 ID Label (Name Plate)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 8 of 10 - 1.3 Control Unit RCU-021 1.3.1 Front View  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 9 of 10 - 1.3.2 Rear View (showing ID Labels)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-016 Date of issue: 6 April 2012 - Page 10 of 10 - 1.3.3 ID Label (Name Plate)

Furuno Labotech International Report no.: FLI 01-12-015 Date of issue:6 April 2012 Form: Q053/01 - Page 1 of 2 - Identification of Equipment for the Furuno Radar FAR-1467DS with Transceiver RTR-110 included (FCC Rule, 2.925) 1. ID Label The following nameplates are permanently fixed on the corresponding equipment units. FCC ID: ADB9ZWRTR110 Material of nameplate: Aluminum, 0.5 mm thick Furuno Labotech International Report no.: FLI 01-12-015 Date of issue:6 April 2012 Form: Q053/01 - Page 2 of 2 - 2. ID Label Location ID label

 Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 1 of 13 - 2 Photographs of Furuno Radar FAR-1467DS (Transceiver type: RTR-110) Inside View 2.1 Scanner Unit RSB-132 2.1.1 Left side View (with Scanner cover opened, showing Transceiver RTR-110 module inside)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 2 of 13 - 2.1.2 Left side View (with Shield covers removed, showing RFC Board 03P9540 (upper), TB Board 03P9539 (middle), IF_AMP Board 03P9541 (lower)) RFC Board TB Board IF_AMP Bd  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 3 of 13 - 2.1.3 Left side View (with PCBs removed)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 4 of 13 - 2.1.4 Right side View (with Scanner cover opened, showing Transceiver module)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 5 of 13 - 2.1.5 Right side View (with shield cover removed, showing Magnetron) Magnetron  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 6 of 13 - 2.1.6 Right side View (Back of chassis, showing PFN2 Board 03P9445 and PFN1 Board 03P9431) Pulse Transformer  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 7 of 13 - 2.1.7 Right side View (with Transceiver module removed)  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 8 of 13 - 2.2 Processor Unit RPU-021 2.2.1 Top View (with Top cover opened) TB Board VIDEO Board GRAPHIC Board MOTHER Board  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 9 of 13 - 2.2.2 Top View (with Shield cover removed, showing AC_PWR Board) AC-PWR Board  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 10 of 13 - 2.2.3 Top View (with TB and VIDEO Boards removed, showing SPU and GC_100 Boards) SPU Board GC_100 Board  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 11 of 13 - 2.2.4 Top View (with AC-PWR Board 03P9494 removed) SSD module GC_100 Board  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 12 of 13 - 2.2.5 Top View (with Shield cover removed, showing ATX Power Unit) ATX Power Unit  Furuno Labotech International Co., Ltd. Document number: FLI 01-12-017 Date of issue: 6 April 2012 - Page 13 of 13 - 2.3 Control Unit RCU-021 2.3.1 Top View (with Top cover opened, showing RADAR-KEY Board 03P9499)

9-52 Ashihara-cho, Nishinomiya, 662-8580, Japan Tel: +81 (798) 65-2111 Fax: +81 (798) 65-4200 www.furuno.co.jp 1/2 Parts list No.: PL-0026 March 14, 2012 Parts List for Marine radar with TT and AIS display Type FAR-1467DS This equipment contains complex modules and printed circuit boards in which fault diagnosis and repair down to component level are not practicable. These modules are listed below: Function modules Module type Remarks 1 Display unit MU-190HD MU-231 19 inch 23.1 inch 1.1 LCD assembly LQ190E1LX51 LQ231U1LW32 MU-190HD MU-231 1.2 CON board 26P0018 N/A MU-190HD MU-231 1.3 PWR board 26P0015 N/A MU-190HD MU-231 1.4 AD board ESSIP28B-1D ESSIP33A-1C MU-190HD MU-231 1.5 PSW board N/A 26P0023 MU-190HD MU-231 1.6 PNL board 26P0013 Common to all models 2 Processor unit RPU-021 AC input 2.1 SPU board 03P9492 2.2 PWR board 03P9494 2.3 FIL board 03P9495 2.4 VIDEO AMP board 03P9493 2.5 FRP TB board 03P9491 2.6 CONE board 03P9515 2.7 MOTHER board BDS-577-03 with GRAPHIC board 2.8 ATX POWER UNIT PS3022 2.9 SSD SDG2A64GMDFBWSZ-SSJA 3 Control unit RCU-021 3.1 PNL board 03P9499 4 Scanner unit RSB-132 21 rpm 200 VAC 3ø 50 Hz / 26 rpm 220 VAC 3ø 60 Hz S-band 4.1 Transceiver block RTR-100 60 kW S-band, TR-up 4.2 IF board 03P9541 4.3 BP board 03P9347 4.4 RF TB board 03P9540 4.5 PFN1 board 03P9431 4.6 PFN2 board 03P9445 4.7 PFN3 board 03P9433 4.8 RFC board 03P9444 4.9 BUF board 03P9446 4.10 SCR board 03P9549 5 Power supply unit PSU-006 5.1 FIL board 01P6130A 5.2 FIL board 03P9466B 5.3 TX-HV board 03P9350A 03P9350B 100/110/115 VAC 220/230 VAC 5.4 MSS board MSS-7497D 9-52 Ashihara-cho, Nishinomiya, 662-8580, Japan Tel: +81 (798) 65-2111 Fax: +81 (798) 65-4200 www.furuno.co.jp 2/2 7 Major discrete parts Parts type Remarks 7.1 Magnetron MG5240F 7.2 Microwave IC IC-0087 7.3 HV transformer RT-9051 7.4 Diode DLM10C-AT1 ED-16H1 7.5 Antenna drive motor RM-7398 7.6 Circulator RC-6584S 7.7 Fan motor MFB52A-12HA-001 BM6015-04W-B59-LQ1 109P1224H402 MMS-06C12DS MFB52A-12HA-001 109P0612H755 RPU-021 2pcs RPU-021 RSB-132 PSU-006 MU-190HD 2pcs / MU-231 1pcs MU-231 2pcs 7.10 Trackball TA4726N1 RCU-021

This report shall not be reproduced except in full, without the written approval of Furuno Labotech International Co., Ltd. Test Report (FCC Rules 2.1046/2.1047/2.1049/2.1051/2.1053/2.1055/80.217) For Trade name: Furuno Model: Transceiver for Marine Radar Type: RTR-110 Report no.: FLI 12-12-055 Date of issue: 6 April 2012 Furuno Labotech International Co., Ltd. 1-16 Fukazu-cho, Nishinomiya-shi, Hyogo 663-8203, Japan Tel: +81-798-63-1094 Fax: +81-798-63-1098 URL: http://www.furuno-labotech.co.jp Furuno Labotech International Report no.: FLI 12-12-055 Form: FQ053/05 - Page 2 of 37 - Report Summary FLI project number: FLI 04-11-0451 Test report number of initial issue: FLI 12-12-055 Date of initial issue 6 April 2012 Test report number of revised/replaced issue: --- Date of revised/replaced issue --- Test report revision/ replacement history: Test report no. Rev. no.Date PageItem Description of change/reason --- --- --- --- --- --- Test standard(s)/ Test specifications: FCC 47 CFR, Sections: 2.1046 - RF Power Output, 2.1047 - Modulation Characteristics, 2.1049 - Occupied Bandwidth, 2.1051 - Spurious Emissions at Antenna Terminal, 2.1055 - Frequency Stability, 2.1053 - Field Strength of Spurious Radiation, 80.217 - Suppression of Interference Aboard Ships. (Date of issue: 1 October 2010) Customer: Furuno Electric Co., Ltd. 9-52 Ashihara-Cho, Nishinomiya-City, 662-8580 Japan Manufacturer: Furuno Electric Co., Ltd. 9-52 Ashihara-Cho, Nishinomiya-City, 662-8580 Japan Trade name: FURUNO Model: Transceiver for Marine Radar Type: RTR-110 Product function and intended use: For Marine Safety navigation Number of samples tested: One Serial number: R156-0460 Power rating: 100 - 115/ 200 - 230 VAC, 50/60 Hz, 2.5/1.3A (for Processer Unit RPU-021) (The EUT was powered through the Processor unit, not directly from AC mains. Product status: Pre-production model Modifications made to samples during testing: None. Date of receipt of samples: 14 December 2011 Test period: 14 December 2011 to 9 February 2012 Place of test: Furuno Labotech International Co., Ltd. - LABOTECH EMC Center 1-16, Fukazu-cho, Nishinomiya-shi, Hyogo, 663-8203 Japan (File number: 818191) - Nishinomiya-Hama Lab. 2-20 Nishinomiya-Hama, Nishinomiya City, Hyogo Prefecture, 662-0934 Japan Anechoic Chamber used for the test has been registered by FCC. (File number: 90607) Test firm Designation Number: JP2007, Test firm Registration #: 838049 Test results/ Compliance: Passed. The test results of this report relate only to the samples tested. Tested by: Akira Inoue Written by: Akiko Inoue Verified by: Yoshihiro Ishii Approved by: Date: 6 April 2012 Name: Yoshihiro Ishii Title: Manager, Technical Department, Furuno Labotech International Co., Ltd. Signature: Furuno Labotech International Report no.: FLI 12-12-055 Form: FQ053/05 - Page 3 of 37 - Testing Laboratory Status Furuno Labotech International Co., Ltd. (hereafter called FLI) has been holding the following status after having been assessed according to the provisions of ISO/IEC 17025 and/or the relevant rules: (1) JAB Accredited Testing Laboratory: - accredited by Japan Accreditation Board (JAB), Gotanda AN Bldg. 3F 22-1 Higashigotanda 1-chome, Shinagawa-ku, Tokyo 141-0022, JAPAN - Laboratory accreditation number: RTL03220 - Date of initial accreditation: 14 January 2011 - Scope of accreditation: Electrical testing - EMC testing (*) (2) Telefication Listed Testing Laboratory: - listed by Telefication B. V., Edisonstraat 12a, 6902 PK Zevenaar, The Netherlands - Laboratory assignment number: L116 - Date of initial listing: 26 July 1999 (*) - for testing the following product categories/ test standards: - EN 60945, IEC 61162-1/-2, and IEC 62288 for Maritime navigation and radiocommunication equipment and systems (3) BSH Recognized Testing Laboratory: - recognized by Bundesamt für Seeschifffahrt und Hydrographie (BSH), Bernhad-Nocht-Str. 78, 20359 Hamburg, Federal Republic of Germany - Recognition certificate number: BSH/4613/06202/1864/11 - Date of initial recognition: 4 April 2003 (*) - for testing the following product categories/ test standards: - IEC/EN 60945, IEC 62388, IEC 61162-1/-2, and IEC 62288 for Marine navigational and radiocommunication equipment and systems (4) TÜV Appointed EMC Test Laboratory: - appointed by TÜV Rheinland Japan Ltd., 19-5 Shin Yokohama 3-chome, Kohoku-ku, Yokohama 222-0033 Japan - Laboratory assignment number: UA 50046428 - Date of initial appointment: 21 December 1998 (*) - for carrying out the tests of: - EN 55011, CISPR 11, EN 55022, CISPR 22, EN 55024, CISPR 24, EN 55025, CISPR 25, EN/IEC 61000-3-2/-3, EN/IEC 61000-4-2/-3/-4/-5/-6/-8/-11, EN/IEC 61000-6-1/-2/-3/-4, EN/IEC 60945, EN/IEC 61326-1, EN/IEC 61326-2-6, EN/IEC 60601-1-2, JIS T 0601-1-2, JIS C 1806-1, ISO 11452-1/-2/-4. (5) RMRS Recognized Testing Laboratory: - recognized by Russian Maritime Register of Shipping (RMRS), 8, Dvortsovaya Nab., St. Petersburg, 191186 Russia - Laboratory recognition number: 11.02594.011 - Date of initial recognition: 27 January 2009 (*) - for carrying out testing in the field of: 21001301 Elecrtrical measurements and tests, 21001302 EMC tests, 21001500 Mechanical measurements and tests, 21002000 Equipment protection degree tests, and 21002100 Climatic tests for Ship’s radio and navigational equipment and IEC 60945: 2002 Note: (*) – The current certificates may be found in the FLI web site (http://www.furuno-labotech.co.jp). Furuno Labotech International Report no.: FLI 12-12-055 Form: FQ053/05 - Page 4 of 37 - TABLE OF CONTENTS Report Summary ............................................................................................................................. 2 Testing Laboratory Status ............................................................................................................. 3 1 Principal Information ................................................................................................................... 5 1.1 Equipment under test (…

Text truncated - open the document above for the full version.