AFJ272103UHF Transceiver

INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operationis subject to the condition that this device does not causeharmful interference. iF43GT/GS UHF TRANSCEIVER IC-F43GT_GS.qxd 04.4.9 1:10 PM Page a (1,1) i EXPLICIT DEFINITIONS R CAUTION! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of thebody, especially the face or eyes, while transmitting. Thetransceiver will perform best if the microphone is 2 to 4 in. (5to 10 cm) away from the lips and the transceiver is vertical. R CAUTION! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. R CAUTION! NEVER short the terminals of the bat- tery pack. DO NOT push PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below +22°F (–30°C) or above+140°F (+60°C).The basic operations, transmission and reception of the trans-ceiver are guaranteed within the specified operating temper-ature range. However, the LCD display may not be operatecorrectly, or show an indication in the case of long hours ofoperation, or after being placed in extremely cold areas. PRECAUTION WORD DEFINITION R WARNING Personal injury, fire hazard or electric shockmay occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No riskof personal injury, fire or electric shock. READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructionsfor the IC-F43GT/GS UHF TRANSCEIVER . IMPORTANTIcom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany,France, Spain, Russia and/or other countries.SmarTrunk II™ is a Trademark of SmarTrunk Systems, Inc. IC-F43GT_GS.qxd 04.4.9 1:10 PM Page i (1,1) ii DO NOT modify the transceiver for any reason. KEEP the transceiver from the heavy rain, and Never immerse it in the water. The transceiver construction is water resistant , not waterproof. The use of non-Icom battery packs/chargers may impairtransceiver performance and invalidate the warranty.For U.S.A. onlyCAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority tooperate this transceiver under FCC regulations. IC-F43GT_GS.qxd 04.4.9 1:10 PM Page ii (1,1) iii IMPORTANT ........................................................................ iEXPLICIT DEFINITIONS ..................................................... iPRECAUTION ..................................................................... iTABLE OF CONTENTS ...................................................... iii1 ACCESSORIES ......................................................... 1–3  Supplied accessories ................................................. 1  Accessory attachments .............................................. 1 2 PANEL DESCRIPTION ........................................... 4–10  Front panel ................................................................. 4  Function display ......................................................... 6  Programmable function keys ..................................... 7 3 BASIC OPERATION .............................................. 11–15  Turning power ON .................................................... 11  Channel selection ..................................................... 11  Call procedure........................................................... 12  Receiving and transmitting........................................ 12  User Set mode .......................................................... 15  Scrambler function .................................................... 15 4 BIIS OPERATION .................................................. 16–27  Default setting .......................................................... 16  Receiving a call ........................................................ 16  Transmitting a call .................................................... 18  Receiving a message ............................................... 20  Transmitting a status ................................................ 22  Transmitting an SDM ............................................... 23  Position data transmission ....................................... 25  Printer connection .................................................... 25  Digital ANI ................................................................ 25  Auto emergency transmission .................................. 26  Stun function ............................................................ 26  BIIS indication .......................................................... 26  Priority A channel selection ...................................... 26  Man Down Emergency Call ..................................... 27 5 OPTIONAL SmarTrunk OPERATION .................. 28–29  SmarTrunk II TM /SmarTrunk 3G and conventional modes ........................................... 28  SmarTrunk II TM /SmarTrunk 3G operation ................. 28 6 OPTIONAL UNIT INSTALLATION ........................ 30–31  Optional unit installation ........................................... 30  Scrambler unit installation ........................................ 31 7 BATTERY CHARGING .......................................... 32–35  Battery charging ....................................................... 32  Battery caution ......................................................... 32  Optional battery chargers ......................................... 33 8 SWIVEL BELT CLIP .............................................. 36–37  MB-93 contents ........................................................ 36  To attach .................................................................. 36  To detach ................................................................. 37 9 OPTIONS…

Text truncated - open the document above for the full version.

Lithium-Ion battery pack The large capacity 1150mAh Li-Ion battery pack, BP-231, provides 8 hours* of operat- ing time. For longer operating time, use the BP-232 which is rated for a full 15 hours*. Li-Ion technology has virtually no memory charging issues. A rugged dual-rail guide securely locks the battery to the radio. * Typical operation Tx:Rx: Stand-by=5:5:90 Wide frequency range and large channel capacity The IC-F43G series covers a wide fre- quency range in one version (Two versions available, 400–470MHz or 450–512 (520) MHz). The 256 memory channel capacity with 16 memory banks allows you to divide and store a variety of flexible channel groupings. Easy memory channel selection with a sim- ple rotation of the rotary channel knob. Small and lightweight body The IC-F43G series sheds size and weight compared with previous models, weighing just 300g (including BP-231)and measuring only 53 (W)×120(H)×32.5(D)mm*. The alu- minum die-cast chassis and polycarbonate casing combination meets MIL standard specifications. * 10.6 oz, 2 3 /32(W)x 4 23 /32(H)x1 9 /32(D)in Built-in multi-format tone signaling Use the built-in CTCSS, DTCS, 2-Tone, 5- Tone or BIIS capability to set up your own talk groups and quiet stand-by when others are talking. You can also set up selective calls to individuals or control a repeater. The IC-F43G series is suitable for a variety of needs — large or small, mobile or station- ary. Whether you are a large-scale construc- tion site, warehouse, hospital or hotel, or a small on the go messenger service, this radio provides the built-in flexibility to han- dle your communication needs. Offering advanced features such as wide fre- quency range, multiple signaling and loud audio, the IC-F43G series is a rugged and re- liable 2-way communications tool. This is the new direction in LMR communications. Advanced functionAdvanced functions packed in a tough, lightweight body Advanced function

September 5, 2004 AmericanTCB, Inc. 6731 Whittier Avenue, Suite C110 McLean, VA 22101 Subject: Type Acceptance Application under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 450-512 MHz (12.5 kHz and 25 kHz Channel Spacings). Applicant: ICOM Incorporated Product: UHF TRANSCEIVER Model: IC-F43GT and IC-F43GS FCC ID: AFJ272103 Dear Sir/Madam, As appointed agent for ICOM Incorporated, we would like to submit the application to Federal Communications Commission for certification of the above product. Please review all files uploaded to ATCB electronic filing site. If you have any queries, please do not hesitate to contact us by our TOLL FREE No.:1-877-747-6381 Yours truly, Tri Minh Luu, P. Eng., V.P., Engineering UltraTech Group of Labs 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] 31040/SIT C-1376 46390-2049 200093-0 2 00-034 SL2-IN-E-1119R

ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 1 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 2 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 3 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 4 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 5 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 6 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 7 ANNEX 2 – EXTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A2 - 8

Label Location FCC ID Label SAR Warning Label

ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 1 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 2 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 3 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 4 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 5 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 6 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 7 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 8 ANNEX 3 – INTERNAL EUT PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT-GS FCC ID: AFJ272103 A3 - 9

UHF TRANSCEIVER Model No.: IC-F43GT/GS Tested For ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka Japan, 547-0003 In Accordance With SAR (Specific Absorption Rate) Requirements using guidelines established in IEEE C95.1-1991, FCC OET Bulletin 65 (Supplement C), Industry Canada RSS-102(Issue 1) and ACA Radiocommunications (Electromagnetic Radiation – Human Exposure) Amendment Standard 2000 (No. 1) UltraTech's File No.: ICOM-088-SAR This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: September 03, 2004 Report Prepared by: JaeWook Choi, SAR System Engineer Tested by: Carolyn Luu Issued Date: September 03, 2004 Test Dates: August 17, 2004 ~ August 18, 2004 The results in this Test Report apply only to the sample(s) tested, which has been randomly selected. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] SPECIFIC ABSORPTION RATE (SAR) Page 1 IEEE C95.1-1991, FCC OET Bulletin 65 (Supplement C), Industry Canada RSS-102(Issue 1) and ACA Radiocommunications (Electromagnetic Radiation – Human Exposure) Amendment Standard 2000 (No. 1) UHF Transceiver M/N: IC-F43GS/GT FCC ID: AFJ272103 ULTRATECH GROUP OF LABS File #: ICOM-088-SAR 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 September 3, 2004 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected], Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA ) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1.INTRODUCTION ................................................................................................................................................ 5 1.1.SCOPE ............................................................................................................................................................................... 5 1.2.REFERENCES................................................................................................................................................................... 5 EXHIBIT 2.PERFORMANCE ASSESSMENT ..................................................................................................................... 6 2.1.CLIENT AND MANUFACTURER INFORMATION ...................................................................................................... 6 2.2.D EVICE UNDER TEST (D.U.T.) DESCRIPTION.............................................................................................................. 6 2.3.LIST OF D.U.T.’S ACCESSORIES:.................................................................................................................................. 7 2.4.SPECIAL CHANGES ON THE D.U.T.’S HARDWARE/SOFTWARE FOR TESTING PURPOSES ............................. 7 2.5.ANCILLARY EQUIPMENT ............................................................................................................................................. 7 2.6.GENERAL TEST CONFIGURATIONS ........................................................................................................................... 7 2.6.1.Equipment Configuration ........................................................................................................................................... 7 2.6.2.Exercising Equipment................................................................................................................................................. 7 2.7.S PECIFIC OPERATING CONDITIONS...................................................................................................................................... 7 2.8.BLOCK DIAGRAM OF TEST SETUP ............................................................................................................................. 8 EXHIBIT 3.SUMMARY OF TEST RESULTS ...................................................................................................................... 9 3.1.LOCATION OF TESTS ..................................................................................................................................................... 9 3.2.APPLICABILITY & SUMMARY OF SAR RESULTS..................................................................................................... 9 EXHIBIT 4.MEASUREMENTS, EXAMINATIONS & TEST DATA .............................................................................. 10 4.1.TEST SETUP ................................................................................................................................................................... 10 4.2.P HOTOGRAPH OF D.U.T. AND ALL ACCESORIES................................................................................................................ 11 4.3.PHOTOGRAPHS OF D.U.T. POSITION ........................................................................................................................19 4.3.1.Head Front Configuration........................................................................................................................................ 19 4.3.1.1.Push-To-Talk; Front-side in parallel to the phantom with the spacing of 25 mm, long antenna (M/N: FA-SC57U or FA- SC25U) 19 4.3.1.2.Push-To-Talk; Front-side in parallel to the phantom with the spacing of 25 mm, stubby antenna (M/N: FA-SC73US) ......... 20 4.3.2.Body-Worn(By stander) Configuration .................................................................................................................... 21 4.3.2.1.Body-worn; Back-side in parallel to the phantom and the belt clip in contact, long…

Text truncated - open the document above for the full version.

UHF TRANSCEIVER Model No.: IC-F43GT and IC-F43GS FCC ID: AFJ272103 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka, Japan 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: ICOM-088FCC90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: September 5, 2004 Report Prepared by: Dharmajit Solanki, RFI Engineer Issued Date: September 5, 2004 Tested by: Hung Trinh, EMI/RFI Technician Test Dates: August 25 – Sept. 5, 2004 ƒ The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. ƒ This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] 2 31040/SIT C-1376 46390-2049 200093-0 SL2-IN-E-1119R 00-034 FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Contents i UHF TRANSCEIVER, Model IC-F43GT and IC-F43GS FCC ID: AFJ272103 ULTRATECH GROUP OF LABS File #: ICOM-088FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 September 5, 2004 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST........................................................................................................................ 1 EXHIBIT 2. INTRODUCTION ......................................................................................................................................... 2 2.1. SCOPE......................................................................................................................................................................... 2 2.2. RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................... 2 2.3. NORMATIVE REFERENCES ................................................................................................................................... 2 EXHIBIT 3. PERFORMANCE ASSESSMENT .............................................................................................................. 3 3.1. CLIENT INFORMATION .......................................................................................................................................... 3 3.2. EQUIPMENT UNDER TEST (EUT) INFORMATION............................................................................................. 3 3.3. EUT’S TECHNICAL SPECIFICATIONS.................................................................................................................. 4 3.4. LIST OF EUT’S PORTS ............................................................................................................................................. 5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ............................... 6 4.1. CLIMATE TEST CONDITIONS................................................................................................................................ 6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS............................................. 6 EXHIBIT 5. SUMMARY OF TEST RESULTS ............................................................................................................... 7 5.1. LOCATION OF TESTS .............................................................................................................................................. 7 5.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ....................................................................... 7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ....................................... 7 5.4. DEVIATION OF STANDARD TEST PROCEDURES ............................................................................................. 7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS............................... 8 6.1. TEST PROCEDURES................................................................................................................................................. 8 6.2. MEASUREMENT UNCERTAINTIES ...................................................................................................................... 8 6.3. MEASUREMENT EQUIPMENT USED ................................................................................................................... 8 6.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER........................................ 8 6.5. RF POWER OUTPUT [§§ 2.1046 & 90.205]............................................................................................................. 9 6.6. FREQUENCY STABILITY [§§ 2.1055 & 90.213] .................................................................................................. 10 6.7. AUDIO FREQUENCY RESPONSE [§ 2.1047(A)] ................................................................................................. 13 6.8. MODULATION LIMITING [§§ 2.1047(B) & 90.210] ............................................................................................ 18 6.9. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 90.209 & 90.210] ................................................ 23 6.10. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§ 90.210].... 61 6.11. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 90.210] ........................................... 74 6.12. TRANSIENT FREQUENCY BEHAVIOR [§ 90.214] ........................................................................................…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A1 - 1 ANNEX 1 - TEST SETUP PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A1 - 2 ANNEX 1 - TEST SETUP PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A1 - 3 ANNEX 1 - TEST SETUP PHOTOS ICOM Incorporated UHF Transceiver, Model IC-F43GT/GS FCC ID: AFJ272103 A1 - 4