AFJIC-910HAmature Scanning Transceiver

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interferenece, and (2)this device must accept any interference received, including interference that may cause undesired operation. WARNING: Modification of this device to receive cellular radiotelephone service signals is prohibited under FCC and Federal law.

Adjustment for IC-910H Adjustment for IC-910HAdjustment for IC-910H Adjustment for IC-910H Adjustment AdjustmentAdjustment Adjustment Adjustment AdjustmentAdjustment AdjustmentNo NoNo NoAdjustment Condition & Tuning Adjustment Condition & TuningAdjustment Condition & Tuning Adjustment Condition & TuningValue Va l u eVa l u e Va l u eR e f . N o . Ref. No.Ref. No. Ref. No. CK. Point CK. PointCK. Point CK. Point 30.2 MHz Level 30.2 MHz Level30.2 MHz Level 30.2 MHz Level Adjustment AdjustmentAdjustment Adjustment Connect a high frequency voltage meter or a spectrum Connect a high frequency voltage meter or a spectrumConnect a high frequency voltage meter or a spectrum Connect a high frequency voltage meter or a spectrum analyzer to J541. Adjust the out- put level at R570. analyzer to J541. Adjust the out- put level at R570.analyzer to J541. Adjust the out- put level at R570. analyzer to J541. Adjust the out- put level at R570. -10dB -10dB-10dB -10dB ± ±± ±0.5dB 0.5dB0.5dB 0.5dB R570 R570R570 R570J541 J541J541 J541 Adjustment of the Adjustment of theAdjustment of the Adjustment of the 430MHz 2 430MHz 2430MHz 2 430MHz 2 nd nd nd nd Lo LoLo Lo (60.4MHz) Peak (60.4MHz) Peak(60.4MHz) Peak (60.4MHz) Peak Connect a high frequency voltage mater or a spectrum Connect a high frequency voltage mater or a spectrumConnect a high frequency voltage mater or a spectrum Connect a high frequency voltage mater or a spectrum analyzer to P551. Adjust the maximum output at L551 and analyzer to P551. Adjust the maximum output at L551 andanalyzer to P551. Adjust the maximum output at L551 and analyzer to P551. Adjust the maximum output at L551 and L552 L552L552 L552 -10dB -10dB-10dB -10dB ± ±± ±3dB 3dB3dB 3dB L551 L551L551 L551 L552 L552L552 L552 P551 P551P551 P551 Setting the 60.4MHz Setting the 60.4MHzSetting the 60.4MHz Setting the 60.4MHz Frequency FrequencyFrequency Frequency *Adjust 5 minutes after power ON *Adjust 5 minutes after power ON*Adjust 5 minutes after power ON *Adjust 5 minutes after power ON Connect a frequency counter to P551 and adjust to 60.4MHz Connect a frequency counter to P551 and adjust to 60.4MHzConnect a frequency counter to P551 and adjust to 60.4MHz Connect a frequency counter to P551 and adjust to 60.4MHz at the trimmer condenser X512. at the trimmer condenser X512.at the trimmer condenser X512. at the trimmer condenser X512. 60.4MHz 60.4MHz60.4MHz 60.4MHz ± ±± ± 10Hz 10Hz 10Hz 10Hz X512 X512X512 X512P551 P551P551 P551 Adjustment of Adjustment ofAdjustment of Adjustment of the144MHz 1 the144MHz 1the144MHz 1 the144MHz 1 st stst st Lo LoLo Lo Lock Voltage Lock VoltageLock Voltage Lock Voltage Connect a tester to CP100. Connect a tester to CP100.Connect a tester to CP100. Connect a tester to CP100. Indicated Frequency: 173.980 MHz Indicated Frequency: 173.980 MHzIndicated Frequency: 173.980 MHz Indicated Frequency: 173.980 MHz MODE: USB MODE: USBMODE: USB MODE: USB Set the voltage at L193. Set the voltage at L193.Set the voltage at L193. Set the voltage at L193. 2.7V 2.7V2.7V 2.7V ± ±± ± 0.1V 0.1V 0.1V 0.1V L193 L193L193 L193CP100 CP100CP100 CP100 Adjustment of Adjustment ofAdjustment of Adjustment of th430MHz 1 th430MHz 1th430MHz 1 th430MHz 1 st stst st Lo LoLo Lo Lock Voltage Lock VoltageLock Voltage Lock Voltage Connect a tester to CP300. Connect a tester to CP300.Connect a tester to CP300. Connect a tester to CP300. Indicated Frequency: 479.980 MHz Indicated Frequency: 479.980 MHzIndicated Frequency: 479.980 MHz Indicated Frequency: 479.980 MHz MODE: USB MODE: USBMODE: USB MODE: USB Set the voltage at C402. Set the voltage at C402.Set the voltage at C402. Set the voltage at C402. 3.4V 3.4V3.4V 3.4V ± ±± ± 0.1V 0.1V 0.1V 0.1V C402 C402C402 C402CP300 CP300CP300 CP300 Adjustment of the Adjustment of theAdjustment of the Adjustment of the 144MHz RX Peak/ 144MHz RX Peak/144MHz RX Peak/ 144MHz RX Peak/ Gain GainGain Gain Connect a signal generator to the VHF antenna connector. Connect a signal generator to the VHF antenna connector.Connect a signal generator to the VHF antenna connector. Connect a signal generator to the VHF antenna connector. Connect a high frequency meter ( Connect a high frequency meter (Connect a high frequency meter ( Connect a high frequency meter (50 ohm terminal) to the 50 ohm terminal) to the50 ohm terminal) to the 50 ohm terminal) to the VHF IF OUT. VHF IF OUT. VHF IF OUT. VHF IF OUT. ( A special jig is necessary). ( A special jig is necessary).( A special jig is necessary). ( A special jig is necessary). S.G. Freq.: 146.0 MHz/-30 S.G. Freq.: 146.0 MHz/-30 S.G. Freq.: 146.0 MHz/-30 S.G. Freq.: 146.0 MHz/-30 dBm dBmdBm dBm Set the PA unit Set the PA unitSet the PA unit Set the PA unit’ ’’ ’s peak adjustment. s peak adjustment.s peak adjustment. s peak adjustment. Adjust the IF output. Adjust the IF output.Adjust the IF output. Adjust the IF output. MAX MAXMAX MAX – –– –14dBm 14dBm14dBm 14dBm ± ±± ± 0.1dBm 0.1dBm 0.1dBm 0.1dBm PA L521 PA L521PA L521 PA L521 PA R547 PA R547PA R547 PA R547 ± ±± ± 0.1dBm 0.1dBm0.1dBm 0.1dBm P501 P501P501 P501 P501 P501P501 P501 Adjustment of Main Adjustment of MainAdjustment of Main Adjustment of Main Band Peak Band PeakBand Peak Band Peak Connect a signal generator to the VHF antenna connector. Connect a signal generator to the VHF antenna connector.Connect a signal generator to the VHF antenna connector. Connect a signal generator to the VHF antenna connector. Transceiver Freq.: 145.98 MHz (Main band) Transceiver Freq.: 145.98 MHz (Main band)Transceiver Freq.: 145.98 MHz (Main band) Transceiver Freq.: 145.98 MHz (Main band) MODE: FM MODE: FMMODE: FM MODE: FM S.G. Freq.: Same as transceiver setting S.G. Freq.: Same as transceiver settingS.G. Freq.: Same as transceiver setting S.G. Freq.: Same as transceiver setting AF: 1 kHz AF: 1 kHzAF: 1 kHz AF: 1 kHz Dev.: 5 kHz Dev.: 5 kHzDev.: 5 kHz Dev.: 5 kHz Output: +10 Output: +10 Output: +10 Output: +10 dBu dBudBu dBu Keep adjusting until the MAIN AF output distortion is at Keep adjusting …

Text truncated - open the document above for the full version.

Issue Date : December 22, 2000 Page 1 of 39 EMC EMISSION - TEST REPORT JQA APPLICATION No.: KL80000447 Name of Product: VHF/UHF Transceiver Model/Type No.: IC-910H FCC ID: AFJ IC-910H Applicant :ICOMIncorporated Address : 1-6-19, Kuratsukuri, Kami, Hirano-ku, Osaka, Japan Manufacturer :ICOMIncorporated Address : 1-6-19, Kuratsukuri, Kami, Hirano-ku, Osaka, Japan Receive date of EUT: November 27, 2000 Final Judgement :Passed TEST RESULTS IN THIS REPORT are obtained in use of equipment that is traceable to Electro- technical Lab. of MITI Japan and Communications Research Lab. of PTT Japan. THE TEST RESULTS only responds to the test sample. This test report shall not be reproduced except in full. Page 2 of 39 DIRECTORY Page A) Documentation Directory2 Test Regulation / General Information3 Test Conditions4-8 Configuration of EUT / Operation mode of the EUT9 - 13 EUT Modification / Responsible Party / Deviation from Standard14 Test results / Measurement Uncertainty15 - 16 Summary17 Test System-Arrangement (Drawings) 18 Preliminary Test and Test-setup (Drawings) 19 - 23 Test-setup (Photographs) at worst case 24 B) Test data ConductedEmission450kHz- 30MHz25 Electromagnetic Field Radiated Emission 30 MHz - 2200 MHz26 - 31 Antenna-Conducted Power30 MHz - 2200 MHz32 - 37 38dB Rejection Test38 - 39 JQA Application No. : KL80000447Regulation : CFR 47 FCC Rules Part 15 Model No.: IC-910HIssue Date : December 22, 2000 FCC ID: AFJ IC-910H JQA Application No. : KL80000447Regulation : CFR 47 FCC Rules Part 15 Model No.: IC-910HIssue Date : December 22, 2000 FCC ID: AFJ IC-910H Page 3 of 39 TEST REGULATION FCC Rules and Regulations Part 15 Subpart A and B (September 20, 2000) !- Class A Digital Device !- Class B Digital Device "- Scanning Receiver Test procedure: The tests were performed according to the procedures in ANSI C63.4-1992. GENERAL INFORMATION Test facility: 1) Test Facility located at Kita-Kansai : 1st and 2nd Open Sites (3 m Site) Test Facility located at Kameoka Open Site (3, 10 and 30 m, on common plane) FCC filing No. : 31040/SIT 1300F2 2) KITA-KANSAI TESTING CENTER is recognized under the National Voluntary Laboratory Accreditation Program for satisfactory compliance established in Title 15, Part 285 Code of Federal Regulations. NVLAP Lab Code: 200191-0 Description of the Equipment Under Test (EUT): 1) Name: VHF/UHF Transceiver 2) Model/Type No.: IC-910H 3) Product Type: Pre-Production (S/N: 000047) 4) Category: Scanning Receiver 5) EUT Authorization: - Verification- Certification- D.o.C.!"! 6) Highest frequency used/generated : 32 MHz 7) Power Rating: DC 13.8V (Power Supply IC-5P : AC120V 60Hz) Definitions for symbols used in this test report: "- Black box indicates that the listed condition, standard or equipment is applicable for this Report. !- Blank box indicates that the listed condition, standard or equipment is not applicable for this Report. JQA Application No. : KL80000447Regulation : CFR 47 FCC Rules Part 15 Model No.: IC-910HIssue Date : December 22, 2000 FCC ID: AFJ IC-910H Page 4 of 39 TEST CONDITIONS AC Powerline Conducted Emission Measurement wasperformedinthefollowingtestsite. Test location: KITA-KANSAI Testing Center 7-7, Ishimaru, 1-Chome, Mino-Shi, Osaka, 562-0027, Japan "-Shieldedroom KAMEOKA EMC Branch 9-1, Ozaki, Inukanno, Nishibetsuin-Cho, Kameoka-Shi, Kyoto, 621-0126, Japan !-Shieldedroom !- On metal plane of open site Used test instruments and sites: Model No.Device IDast Cal. DateCal. Interval L "-ESCS30A-1August,20001Year !-ESH2A-2 !-ESH2A-3 "- KNW-407D - 6January, 20001 Year !- KNW-408D - 11 !-KNW-242D-7 !- ESH3-Z5D - 12 !- KNW-341CD - 13 !- KNW-408D - 14 !- KNW-244CD - 77 !- KNW-408D - 78 !- ESH2-Z5D - 10 !- ESH2-Z3D - 17 !- 65 BNC-50-0-1H - 26 !- 65 BNC-50-0-1H - 27 !-CableH-7 "- CableH - 8January, 20001 Year Environmental conditions: Temperature: 22 °C Humidity: 38 % JQA Application No. : KL80000447Regulation : CFR 47 FCC Rules Part 15 Model No.: IC-910HIssue Date : December 22, 2000 FCC ID: AFJ IC-910H Page 5 of 39 Electromagnetic Field Radiated Emission Measurement was performed in horizontal and vertical polarization, in the frequency range of 30 MHz - 1000 MHz, in the following test site. Test location: KITA-KANSAI Testing Center 7-7, Ishimaru, 1-Chome, Mino-Shi, Osaka, 562-0027, Japan !- 1st open test site (3 meters) "- 2nd open test site (3 meters) KAMEOKA EMC Branch 9-1, Ozaki, Inukanno, Nishibetsuin-Cho, Kameoka-Shi, Kyoto, 621-0126, Japan !!!!- 1st open test site- 3 m- 10 m- 30 m !!!- 2nd open test site- 3 m- 10 m Validation of Site Attenuation: 1) Last Confirmed Date : October 26, 2000 2) Interval: 1 Year Used test instruments: Model No.Device IDast Cal. DateCal. Interval L !-ESV/ESV-Z3A-7/A-17 "-ESV/ESV-Z3A-6/A-18December,19991Year !-ESV/ESV-Z3A-4/A-20 !-ESV/ESV-Z3A-8/A-19 !-ESVS10A-5 !- KBA-511AC - 12 !- KBA-611C - 22 "- KBA-511AC - 13November, 20001 Year "- KBA-611C - 19November, 20001 Year !- KBA-511AC - 11 !- KBA-611C - 21 !-CableH-1 !-CableH-2 !-CableH-5 "- CableH - 6November, 20001 Year !-CableH-9 Environmental conditions: Temperature: 14 °C Humidity: 53 % JQA Application No. : KL80000447Regulation : CFR 47 FCC Rules Part 15 Model No.: IC-910HIssue Date : December 22, 2000 FCC ID: AFJ IC-910H Page 6 of 39 Electromagnetic Field Radiated Emission Measurement was performed in horizontal and vertical polarization, in the frequency range of 1000 MHz - 2200 MHz, in the following test site. Test location: KITA-KANSAI Testing Center 7-7, Ishimaru, 1-Chome, Mino-Shi, Osaka, 562-0027, Japan !- 1st open test site (3 meters) "- 2nd open test site (3 meters) KAMEOKA EMC Branch 9-1, Ozaki, Inukanno, Nishibetsuin-Cho, Kameoka-Shi, Kyoto, 621-0126, Japan !!!!- 1st open test site- 3 m- 10 m- 30 m !!!- 2nd open test site- 3 m- 10 m Used test instruments: Model No.Device IDast Cal. DateCal. Interval L "-ESCS30A-1August,20001Year !- 8566BA - 13 !- 8593AA - 15 !-ESVA-6 "- 4T-10D - 73May, 20001 Year "- 4T-10D - 74May, 20001 Year "- WJ-6611-513A - 23May, 20001 Y…

Text truncated - open the document above for the full version.