AL8-BBSStereo Bluetooth/Corded Headset

The rst time you power on your headphones, the pairing process begins. 1 Slide the power switch on. You hear "pairing" and the LEDs ash red and blue. GET PAIRED 2 Activate Bluetooth on your phone and set it to search for new devices. • iPhone Settings > Bluetooth > On* • Android Settings > On > Scan for devices* *Menus may vary by device. 3 Select “PLT_SLB.” If necessary, enter four zeros (0000) for the passcode or accept the connection. Once successfully paired, you hear “pairing successful” and the LEDs stop ashing. ([ ]) HEADPHONE OVERVIEW Play/pause music Tap the Play/pause button. Volume Rotate the volume wheel forward (+) or backward (–) to control the volume. Track selection Tap the Forward button or Back button to control the track selection. Open mic Tap the red button to hear your natural surroundings. Voice dial (smartphone) If your smartphone has a voice-enabled assistant, press and hold the Call button for 3 seconds and wait for the phone prompt. Answer a call Choose: • Put on the headset to answer call, or • Tap the Call button End a call Tap the Call button to end current call. Decline a call Press and hold the Call button for 2 seconds. Mute During a call, press the red button. You hear "mute on/o." While muted, taking o the headphones transfers the call to your phone. Call back last call (smartphone) To dial your last number you dialed, double-tap the Call button. It takes up to 2 hours to fully charge your headphones. The LEDs turn o once charging is complete. = = = = = Tip: To check the headphones battery status, tap the Call button while wearing your headphones. Headphones must be in idle state. Your headphones have up to 12 hours of listening time. CHARGE Adjust the headphones for a comfortable t. Lengthen or shorten the band until it ts comfortably. ADJUST THE FIT 1 Slide and hold the power button towards the Bluetooth icon until the LEDs ash red and blue. 2 Activate Bluetooth on your second device and follow steps 2 and step 3 in "Get Paired." PAIR SECOND DEVICE Smart sensors respond when you put on or take o your headphones. Putting on your headphones will: • Resume music • Answer a call Taking off your headphones will: • Pause music (while music is playing) • Transfer active call to phone Disable sensors To disable the sensors, hold both the Mute and Call buttons for more than 6 seconds until the LED ashes purple then red. Repeat to reactivate; the LED ashes purple then blue. USE SENSORS When the battery is exhausted use your headphones with the provided 3.5 mm Apple cable. Use the cable to: • Adjust the volume with the (+) and (–) buttons. • Play/pause music or answer/end a call with the button = single tap • Track forward with the button = double tap • Track backward with the button = triple tap • Activate Siri with the button = 3 second press HYBRID_MODE To enable HD voice (wideband), hold both the red button and Play/pause buttons for more than 6 seconds until the LEDs ashes purple. Repeat to disable. HD voice functions properly when both devices support it. ENABLE HD VOICE If your Mac is Bluetooth-enabled, you can pair your headset to it. 1 Place your headset in pair mode (slide and hold the power button towards the Bluetooth icon). 2 On you mac, choose Apple menu > System Preferences. 3 Click Set Up New Device (+), select "PLT_SLB" and follow the onscreen instructions. PAIR TO MAC You can change the language and other settings by downloading Plantronics Hub for Windows and Mac at plantronics.com/software. You can also download the free mobile apps Plantronics Hub for iOS and Android. Plantronics Hub enables you to: • Change language (Plantronics Hub for Windows and Mac only) • Receive rmware updates (Pla ntronics Hub for Windows and Mac only) • Turn "mute o" voice alert on/o • Turn smart sensors on/o CUSTOMIZE GET STARTED SUBLIME Designed in Santa Cruz, California Read the guides for setup, use and safety. For more help, don’t return to the store; nd a local phone support number at plantronics.com/support. NEED MORE HELP? © 2014 Plantronics, Inc. All Rights Reserved. Bluetooth is a registered trademark of Bluetooth SIG, Inc. and any use by Plantronics is under license. iPhone is a trademark of Apple, Inc. All other trademarks are the property of their respective owners. Patents: U.S. 5,712,453; 7,039,179; Patents pending. 200462-XX 11.14 MODEL ID: PITE14 FCC statement · This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ·These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. ·If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. The measured SAR levels evaluated are in compliance with the FCC RF exposure guidelines. . NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NO…

Text truncated - open the document above for the full version.

Plantronics, Inc. Date：2015-01-26 Federal Communications Commission Authorization and Evaluation Division FCC ID: AL8-BBS Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1 Schematics 2 Block Diagram 3 Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. Sincerely, Peter Clark /Sr. Manager, WW Compliance Engineering Plantronics, Inc.

Plantronics, Inc. Date: 2015-01-26 Federal Communications Commission Authorization and Evaluation Division FCC ID: AL8-BBS ATTESTATION FCC ID: AL8-BBS Product: Stereo Bluetooth/Corded headset Model: BackBeat SENSE We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. Sincerely, __________________ Peter Clark / Sr. Manager, WW Compliance Engineering Plantronics, Inc.

RF_160, Issue 02 Plantronics, Inc. We Name: Plantronics, Inc. Address: 345 Encinal Street, Santa Cruz, CA95060 USA City: California............................................................................ Country: United States ............................................................................ Declare that: Name Representative of agent: Gene Chang (1) Agent Company name: QuieTek Corp. Address: Fl.2, No.345, Xin-hu 2 nd Rd., Nei-hu District City: Taipei Country Taiwan is authorized to apply for Certification of the following product(s): Product description: Stereo Bluetooth/Corded headset............ Type designation: BackBeat SENSE.................. Trademark: Plantronics on our behalf. Date: ...... 2015-01-26.............. City: ...... California.......................... Name: ...... Peter Clark ................................ Function: ...... Sr. Manager, WW Compliance Engineering ............................ Signature: .................................................................. Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

Plantronics, Inc. 345 Encinal Street, Santa Cruz, CA95060 USA Attestation for FCC Declaration of Conformity FCC ID: AL8-BBS Date: 2015/01/26 Please be notified that we, the undersigned, Plantronics, Inc. declares that the product which bears the above FCC ID is also compliant with the FCC requirements for DOC. The test report number supporting the DOC is 14C0188R-RF-US-P01V01Testing in regards to this report was done by QuieTek Corp., located at No.5-22, Rueishu Keng, Rueiping Tsuen, Linkou Shiang, Taipei County 244, Taiwan, which has been accredited in accordance to all of the requirements of 47CFR 2.948 (d) and (e) of the FCC rules and KDB349827. Sincerely, __________________ Peter Clark / Sr. Manager, WW Compliance Engineering Plantronics, Inc.

Plantronics, Inc. Data: 2015-03-06 Office of Engineering and Technology Federal Communication Commission 7435 Oakland Mills Road Columbia, MID 21046-1609 Subject : SHORT-TERM Confidentiality request for FCC ID: AL8-BT600 To Whom It May Concern, ___ Plantronics, Inc.___(the applicant) attests that none of the products certified under FCC ID: AL8-BT600 has been marketed in the U.S. since the certification was granted on 13/02/2015 and acknowledges that the requested exhibits for SHORT-TERM Confidentiality below have been viewable to the public since 01/08/2015. Pursuant to Section 0.457 (d)(1)(ii) and 0.459 of 47CFR, the applicant requests the following documents contained in this application be temporarily withheld from public disclosure for a period of 180 days: Type of Confidentiality Requested Exhibit Short Term External Photos Short Term Internal Photos Short Term Test Setup Photos Short Term User’s Manual _ Plantronics, Inc.______(the applicant) also acknowledges that they will also provide appropriate notice to ACB should either of the following occur: a) If the applicatnt requires aditional 45 days extension periods they will notify ACB with a new request letter at least 7 days prior to the short-term confidentiality expiration date – or b) Immediately notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents above for public disclosure pursuant to the FCC Public Notice. Name / Title: Peter Clark / Sr. Manager, WW Compliance Engineer Company name: Plantronics, Inc. Tel: 831 458 7585 E-mail: [email protected]

Plantronics, Inc. Data: 2015-06-30 Office of Engineering and Technology Federal Communication Commission 7435 Oakland Mills Road Columbia, MID 21046-1609 Subject : SHORT-TERM Confidentiality request for FCC ID: AL8-BBS To Whom It May Concern, ___ Plantronics, Inc.___(the applicant) attests that none of the products certified under FCC ID: AL8-BBS has been marketed in the U.S. since the certification was granted on 13/02/2015 and acknowledges that the requested exhibits for SHORT-TERM Confidentiality below have been viewable to the public since 28/06/2015. Pursuant to Section 0.457 (d)(1)(ii) and 0.459 of 47CFR, the applicant requests the following documents contained in this application be temporarily withheld from public disclosure for a period of 180 days: Type of Confidentiality Requested Exhibit Short Term External Photos Short Term Internal Photos Short Term Test Setup Photos Short Term User’s Manual _ Plantronics, Inc.______(the applicant) also acknowledges that they will also provide appropriate notice to ACB should either of the following occur: a) If the applicatnt requires aditional 45 days extension periods they will notify ACB with a new request letter at least 7 days prior to the short-term confidentiality expiration date – or b) Immediately notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents above for public disclosure pursuant to the FCC Public Notice. Name / Title: Peter Clark / Sr. Manager, WW Compliance Engineer Company name: Plantronics, Inc. Tel: 831 458 7585 E-mail: [email protected]

EUT Photograph (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo

2013 Pierre Harper/ Joe YangB Sublime Regulatory Marking Artmaster203184 1.23.2015 33 mm 6 mm Model:BackBeat SENSE CCAH12LP0790T4 XXXX/SDPPI/YYYY MSIP-CMM-PLT-BBS IC: 457A-BBS ESD-XXXXXXXX XXXX FCC ID: AL8-BBS Anatel: XXXX-XX-XXXX CMIIT ID: XXXXXXXXXX XXXXX XXXXX AB Yoke Inner (Music side) Scale: 1:1Scale: 2:1 NOT FOR SALE

EUT Photograph (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo

For FCC Standalone SAR test exclusion considerations FCC ID: AL8-BBS Tunable Range F(GHz) Low F(GHz) High 2.402 2.480 According to KDB 447498 D01 General RF Exposure Guidance v05 4.3.1 Standalone SAR test exclusion considerations The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR Note: when the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Based on the Maximum measured transmitter power: Max Average Power (dBm) Maximum Antenna Gain (dBi) Pout EIRP (mW) 7.42 2.17 9.11 Maximum TX Power is 5.52 mW Conducted and 9.11 mW EIRP [(9.11 mW/5 mm)* √2.441(GHz)]=2.85 <3.0 Conclusion: Bluetooth SAR was not required.

Test Report FCC Part15 Subpart C Product Name : Stereo Bluetooth/Corded headset Model No. : BackBeat SENSE FCC ID : AL8-BBS IC : 457A-BBS Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Date of Receipt : Dec. 03, 2014 Test Date : Dec. 03, 2014~ Dec. 31, 2014 Issued Date : Jan. 08, 2015 Report No. : 14C0188R-RF-US-P06V02 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of QuieTek Corporation. Report No.: 14C0188R-RF-US-P06V02 Page: 2 of 55 Test Report Certification Issued Date : Jan. 08, 2015 Report No. : 14C0188R-RF-US-P06V02 Product Name : Stereo Bluetooth/Corded headset Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Manufacturer : Weifang GoerTek Electronics Co,.Ltd. Address : Weifang Free Trade Zone, Gaoxin 2 Road, High-Tech Industrial Development Zone, Weifang, Shandong Province, 261205, China Model No. : BackBeat SENSE FCC ID : AL8-BBS IC : 457A-BBS EUT Voltage : DC: 3.7V Brand Name : Plantronics Applicable Standard : FCC CFR Title 47 Part 15 Subpart C: 2014 ANSI C63.4: 2014; ANSI C63.10: 2013 KDB 558074 D01 DTS Meas Guidance v03r02 Industry Canada RSS-Gen Issue 4 / RSS-210 Issue 8 Test Result : Complied Performed Location : Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Registration Number: 800392; IC Lab Code: 4075B Documented By : Reviewed By : Approved By : Report No.: 14C0188R-RF-US-P06V02 Page: 3 of 55 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site :http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] LinKou Testing Laboratory : No.5-22, Ruishukeng, Linkou Dist., New Taipei City 24451, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected] Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., SuZhou, China TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : [email protected] Taiwan R.O.C. :BSMI, NCC, TAF Germany :TUV Rheinland Norway :Nemko, DNV USA :FCC Japan :VCCI China :CNAS Report No.: 14C0188R-RF-US-P06V02 Page: 4 of 55 TABLE OF CONTENTS Description Page 1. General Information ...................................................................................................... 7 1.1. EUT Description ............................................................................................................ 7 1.2. Mode of Operation ...................................................................................................... 10 1.3. Tested System Details ................................................................................................ 11 1.4. Configuration of Tested System .................................................................................. 12 1.5. EUT Exercise Software ............................................................................................... 13 2. Technical Test ............................................................................................................. 14 2.1. Summary of Test Result .............................................................................................. 14 2.2. Test Environment ........................................................................................................ 16 3. Conducted Emission ................................................................................................... 17 3.1. Test Equipment ........................................................................................................... 17 3.2. Test Setup ................................................................................................................... 17 3.3. Limit ............................................................................................................................ 18 3.4. Test Procedure ............................................................................................................ 18 3.5. Uncertainty .................................................................................................................. 18 3.6. Test Result .................................................................................................................. 19 4. Radiated Emission ...................................................................................................... 21 4.1. Test Equipment ........................................................................................................... 21 4.2. Test Setup ................................................................................................................... 22 4.3. Limit ..................................................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photograph for Part 15.247 Description: Radiated Emission Test Setup for Below 30MHz Description: Radiated Emission Test Setup for Below 1GHz Description: Radiated Emission Test Setup for 1~18GHz Description: Radiated Emission Test Setup for Above 18GHz