AL8-PBVOYX2Bluetooth Base

3390 East Harmony Road Fort Collins Colorado 80528 United States U.S. Agent for Service of Process Attestation To the attention of Federal Communications Commission Authorization and Evaluation Division Applicant / Designated U.S Agent Company Name: HP Inc. FRN: 0025126541 Grantee Code: AL8 Contact Person: Richard P Tarsio Street Address: 3390 East Harmony Road, Colorado, United States, City/Province/Zip: Fort Collins 80528 Tel.: 970-898-8713 Email: [email protected] This letter is to confirm that the Applicant has designated itself as the U.S Agent for service of process as required by §2.911(d)(7). The Applicant further acknowledges acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. Applicant / U.S. Agent Signature: Date: 2024-05-24 Name: Richard Tarsio Job Title: Technical Regulations & Standards Engineer USA/CAN Company Name: HP Inc.

HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA Date: 5/24/2024 FCC ID: AL8-PBVOYX2 To The attention of Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attestation Statements Part 2.911(d)(5)(i) Filing HP Inc. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Attestation Statements Part 2.911(d)(5)(ii) Filing HP Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Ismael Talancon Lara Job Title: Manager, Hybrid System & Peripheral Compliance Company Name: HP Inc.

Date: 05/13/2024 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC; b) supply any and all information needed for the evaluation of the products for which certification is sought; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized; e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification; f) use certification only to indicate that products are certified in conformity with specified standards; g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety; h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements; i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers; j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements; k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCB’s or the FCC’s market surveillance requirements; l) keep a record of all complaints relating to product’s compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies; m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Ismael Talancon Lara Manager, Hybrid System & Peripheral Compliance HP Inc.

Date: 5/24/2024 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Subject: Request for Confidentiality FCC ID: AL8-PBVOYX2 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. • Schematic Diagram • Block Diagram • Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until December 02, 2024 • External Photos • Internal Photos • Test Setup Photos • User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Ismael Talancon Lara Manager, Hybrid Systems & Peripheral Compliance Hp Inc.

HP Inc. 3390 E Harmony Rd Fort Collins, CO 80528 USA Authorization on Behalf of HP Inc. for the US Federal Communications Commission Office of Engineering and Technology and Other FCC Programs and Offices 1.I , Richard P. Tarsio, am on the Worldwide Technical Regulations staff of HP Inc. (“HP”) and Applicant/Grantee Contact of Record for HP Inc. together with its subsidiaries and affiliates worldwide (collectively, “HP”) for HP’s dealings with the United States Federal Communications Commission (“FCC”). I am duly authorized by HP to make this Authorization on HP’s behalf. 2.T his Authorization will designate the person named below to act on my behalf and HP’s behalf as an authorized agent and representative, until further notice, with the additional power to designate one or more third party agents for HP with regard to particular matters and applications. All acts carried out and requests made by this named representative relating to any matter before the FCC, including requests fo r c onfidentiality, shall have the same effect as mine . N ame: Ismael Talancon Lara Title: Manager, Hybrid System & Peripheral Compliance Address: Poly Com S. de R.L. de C.V. Boulevard Bellas Artes No. 20308, Colonia Ciudad Industrial Tijuana, BC Mexico 22444 Telephone: +52 664 647-4968 E-mail: [email protected] 3.Q uestions about the scope and effect of this Authorization should be addressed as follows: Richard P. Tarsio US/Canada Technical Regulations & Standards Engineer Worldwide Technical Regulations HP Inc. (A ) 3390 E ast Harmony Road, MS 66 Fort Collins, CO 80528 (T ) + 1 970 898 8713 (E ) ri [email protected] 4.I declare under penalty of perjury that the foregoing is true and correct, and that this Authorization was executed at Fort Collins, Colorado on the date indicated below my signature. R ichard P. Tarsio US/Canada Technical Regulations & Standards Engineer HP Inc. Date: 8 January 2024

HP Inc. 1501 Page Mill Road Palo Alto, CA, 94304 USA Hp.com June 13, 2024 LETTER OF SIMILARITY Ref: Declaration of Similarity between Regulatory Models PBVOY72 and PBVOY52 To Whom It May Concern, We, HP Inc., as the manufacturer located at 1501 Page Mill Road, Palo Alto, CA 94304, USA, hereby issue this letter to declare the similarity between our two products, with Regulatory model names: PBVOY72 and PBVOY52. Both models are equipped with the same PCBA assembly with identical electrical and radio circuitry, and input/output ports. The primary distinction between the two is the external mechanics of the charging cradles, tailored to accommodate different headset types and form factors. Specifically, PBVOY72 charging cradle is designed to support the Poly Voyager over-the-head headsets, including the Voyager Focus 2 and Voyager 4300 series. Conversely, PBVOY52 is compatible with our over-the-ear headsets, such as the Voyager 5200 series. This declaration is intended to assist in addressing any regulatory or compliance questions clarification regarding the relationship and similarities between these two models. Should you require further details, please do not hesitate to contact us. Thank you for your attention. Sincerely, _____________________________ Name: Ismael Talancon Job title: Manager, Hybrid System & Peripheral Compliance Email: [email protected]

HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA May 24th, 2024 Product Information Model: PBVOY52 HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA Model: PBVOY72 HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA Label Location The Product will be marked using a pressure sensitive adhesive label attached to the underside of the base and printed using a pad printer.

Report Number. : 15078301-E2V2 Applicant : HP Inc. 1501 Page Mill Road Palo Alto, CA 94304 US Model : PBVOY42, PBVOY52, PBVOY72 Brand : Poly FCC ID : AL8-PBVOYX2 IC : 457A-PBVOYX2 EUT Description : Bluetooth Base Test Standard(s) : FCC Part 1 Subpart I FCC Part 2 Subpart J RSS 102 ISSUE 5 Date Of Issue: 2024-06-13 Prepared by: UL VERIFICATION SERVICES 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 15078301-E2V2 DATE: 2024-06-13 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 2 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By V1 2024-05-02 Initial Issue -- V2 2024-06-13 Section 7 Updated Henry Lau REPORT NO: 15078301-E2V2 DATE: 2024-06-13 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 3 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS .................................................................................... 4 2. TEST METHODOLOGY ........................................................................................................ 5 3. REFERENCES ...................................................................................................................... 5 4. FACILITIES AND ACCREDITATION .................................................................................... 5 5. EQUIPMENT UNDER TEST ................................................................................................. 6 5.1. EUT DESCRIPTION ....................................................................................................... 6 5.2. Manufacturer’s Description of Model Differences ........................................................... 6 5.3. MAXIMUM OUTPUT POWER ........................................................................................ 6 5.4. DESCRIPTION OF AVAILABLE ANTENNAS ................................................................ 6 6. MAXIMUM PERMISSIBLE EXPOSURE (LIMITS AND EQUATIONS) ................................. 7 6.1. FCC RULES ................................................................................................................... 7 6.2. ISED RULES .................................................................................................................. 8 6.3. EQUATIONS .................................................................................................................. 9 7. RF EXPOSURE RESULTS ................................................................................................. 11 8. ISED MOBILE/FIXED DEVICE TEST EXCLUSION ........................................................... 12 8.1. RSS-102 Clause 2.5.2 Exemption Limits ..................................................................... 12 8.2. Exemption Results ........................................................................................................ 12 REPORT NO: 15078301-E2V2 DATE: 2024-06-13 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 4 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: HP Inc. 1501 Page Mill Road Palo Alto, CA 94304 US EUT DESCRIPTION: Bluetooth Base MODEL: PBVOY42, PBVOY52, PBVOY72 BRAND: Poly APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Complies RSS 102 ISSUE 5 Complies UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. All samples tested were in good operating condition throughout the entire test program. Measurement Uncertainties are published for informational purposes only and were not taken into account unless noted otherwise. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. Approved & Released For UL Verification Services Inc. By: Prepared By: Dan Coronia Henry Lau Operations Leader Senior Project Engineer CONSUMER TECHNOLOGY DIVISION CONSUMER TECHNOLOGY DIVISION UL Verification Services Inc. UL Verification Services Inc. REPORT NO: 15078301-E2V2 DATE: 2024-06-13 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 5 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 2. TEST METHODOLOGY All calculations were made in accordance with FCC Parts 1.1310, 2.1091, 2.1093, KDB 447498 D01 v06, KDB 447498 D03 V01, IEEE Std C95.1-2005, IEEE Std C95.3-2002, IC Safety Code 6 and RSS 102 Issue 5. This report contains data provided by the customer which can impact the validity of results. UL Verification Services Inc. is only responsible f…

Text truncated - open the document above for the full version.

HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA Antenna datasheet for PBVOY52 PBVOY72 General Information Antenna Manufacturer JIAXINYUAN INDUSTRIAL HK LTD. Address 909B 9/F TWO GRAND TOWER, 625 NATHAN RD KOWLOON, HONG KONG, CHINA Antenna Type Omni directional, mono pole Model 84433-03 Antenna Information T he antenna construction and performance: Antenna operating band: 2402 - 2480 MHz Antenna type Omni directional, mono pole Connector type None – not removable Peak gain (directional) 2.85 dBi maximum Measurement by Di rect Comparison Method Test Position Free Space Frequently (MHz) 2402 2441 2480 Average Gain (dBi) -1.30-1.23-0.94 Peak Gain (dBi) 1.92 2.26 2.85 HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA H To t a l Max: 3 Min: -5 Scale: 1/div E1 To t a l Max: 3 Min: -5 Scale: 1/div E2 Angle (? 0 180 30 210 60 240 90 270 120 300 150 330 MHz 2402 MHz 2441 MHz 2480 Angle (? 0 180 30 210 60 240 90 270 120 300 150 330 MHz 2402 MHz 2441 MHz 2480 HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA To t a l Scale: 2/div 180 Angle (? 2402 MHz 2441 MHz 2480 MHz Min: -10 Max: 2 0 30 210 60 240 90 270 120 300 150 330 HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA To t a l HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA Antenna photo:

TEST REPORT Report Number. : 15078301-E1V1 Applicant : HP Inc. 1501 Page Mill Road Palo Alto, CA 94304 US Model : PBVOY42, PBVOY52, PBVOY72 Brand : Poly FCC ID : AL8-PBVOYX2 IC : 457A-PBVOYX2 EUT Description : Bluetooth Base Test Standard(s) : FCC 47 CFR PART 15 SUBPART C ISED RSS-247 ISSUE 3 ISED RSS-GEN ISSUE 5 + A1 + A2 Date Of Issue: 2024-04-26 Prepared by: UL VERIFICATION SERVICES 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 15078301-E1V1 DATE: 2024-04-26 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 2 of 78 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES REPORT REVISION HISTORY Rev. Issue Date Revisions Revised By V1 2024-04-26 Initial Issue -- REPORT NO: 15078301-E1V1 DATE: 2024-04-26 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 3 of 78 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES TABLE OF CONTENTS REPORT REVISION HISTORY ................................................................................................. 2 TABLE OF CONTENTS ............................................................................................................ 3 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST RESULTS SUMMARY .............................................................................................. 6 3. TEST METHODOLOGY ..................................................................................................... 7 4. FACILITIES AND ACCREDITATION ................................................................................. 7 5. DECISION RULES AND MEASUREMENT UNCERTAINTY .............................................. 8 5.1. METROLOGICAL TRACEABILITY .............................................................................. 8 5.2. DECISION RULES ....................................................................................................... 8 5.3. MEASUREMENT UNCERTAINTY ............................................................................... 8 5.4. SAMPLE CALCULATION ............................................................................................ 9 6. EQUIPMENT UNDER TEST ..............................................................................................10 6.1. EUT DESCRIPTION ...................................................................................................10 6.2. Manufacturer’s Description of Model Differences ........................................................10 6.3. MAXIMUM OUTPUT POWER.....................................................................................10 6.4. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................10 6.5. SOFTWARE AND FIRMWARE ...................................................................................10 6.6. WORST-CASE CONFIGURATION AND MODE .........................................................11 6.7. DESCRIPTION OF TEST SETUP ...............................................................................11 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................13 8. MEASUREMENT METHODS ............................................................................................14 9. ANTENNA PORT TEST RESULTS ...................................................................................15 9.1. 20 dB AND 99% BANDWIDTH ...................................................................................15 9.1.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................16 9.1.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................18 9.2. ON TIME AND DUTY CYCLE .....................................................................................20 9.3. HOPPING FREQUENCY SEPARATION ....................................................................21 9.3.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................22 9.3.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................23 9.4. NUMBER OF HOPPING CHANNELS .........................................................................24 9.4.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................25 9.4.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................27 REPORT NO: 15078301-E1V1 DATE: 2024-04-26 FCC ID: AL8-PBVOYX2 IC: 457A-PBVOYX2 Page 4 of 78 UL VERIFICATION SERVICES 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL VERIFICATION SERVICES 9.5. AVERAGE TIME OF OCCUPANCY............................................................................29 9.5.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................30 9.5.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................32 9.6. OUTPUT POWER.......................................................................................................34 9.6.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................35 9.6.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................36 9.6.3. BLUETOOTH ENHANCED DATA RATE DQPSK MODULATION .......................37 9.7. AVERAGE POWER ....................................................................................................38 9.7.1. BLUETOOTH BASIC DATA RATE GFSK MODULATION ...................................39 9.7.2. BLUETOOTH ENHANCED DATA RATE 8PSK MODULATION ...........................40 9.7.3. BLUETOOTH ENHANCED DATA RATE DQPSK MODULATION ...............…

Text truncated - open the document above for the full version.

Nemko Canada Inc., a testing laboratory, is accredited by the ANSI National Accreditation Board. The tests included in this report are within the scope of this accreditation www.nemko.com TCA.docx; Date: May 2017 Report reference No REP032405 Test item description Bluetooth Audio Base Model PBVOY52, PBVOY72 Testing Laboratory Nemko Canada Inc. Address 303 River Road Ottawa, Ontario, Canada, K1V 1H2 +1 (613) 737-9680 Applicant's Name HP Inc. Address 1501 Page Mill Road, Palo Alto, CA 94304 USA Test specification ANSI/TIA-968-B, Telecommunications, Telephone Terminal Equipment, Technical Requirements for Connection of Terminal Equipment to the Telephone Network, Approved: August 11, 2009 TIA-968-B-1 Addendum 1, June 2012 TIA-968-B-2 Addendum 2, January 2015 TIA-968-B-3 Addendum 3, March 2016 & Part 68, FCC rules for Registration of Telephone Equipment & CS-03 Part I, Issue 9 Amendment 5, March 2016, Requirements for terminal equipment and related access arrangements intended for direct connection to analogue wireline facilities Tested by Kurt Mikolajewski Telecom Specialist Approved by Stuart Beck Director, Nemko Group Certification Date of issue April 5, 2024 Number of Pages 99 Project No.: PRJ0054142 Report No.: REP032405 Page 2 of 99 This test report shall not be reproduced in any form except in full without the written approval of the Test Laboratory. Table of contents 1 Client information ............................................................................................................................................................................... 3 2 Equipment details ............................................................................................................................................................................... 3 3 Test project performance .................................................................................................................................................................... 3 4 Test report summary .......................................................................................................................................................................... 4 5 Equipment under test ......................................................................................................................................................................... 4 5.1 EUT Description............................................................................................................................................................................ 4 5.2 Technical judgement ..................................................................................................................................................................... 4 5.3 Modification performed during the assessment ............................................................................................................................. 5 5.4 Additional observations ................................................................................................................................................................. 5 5.5 Samples Submitted for testing ...................................................................................................................................................... 6 6 Test laboratory description ................................................................................................................................................................. 6 7 Test equipment used .......................................................................................................................................................................... 6 8 Photographs of test samples .............................................................................................................................................................. 7 8.1 EUT PBVOY52 Top & Front View ................................................................................................................................................. 8 8.2 EUT PBVOY52 Rear View ............................................................................................................................................................ 9 8.3 EUT PBVOY52 Bottom View ...................................................................................................................................................... 10 8.4 EUT PBVOY52 Main PCB Top View ........................................................................................................................................... 11 8.5 EUT PBVOY52 Main PCB Bottom View ...................................................................................................................................... 12 8.6 EUT Handset adaptor cable View ............................................................................................................................................... 13 8.7 EUT Over Ear Headset ............................................................................................................................................................... 13 8.8 EUT Power Pack View ................................................................................................................................................................ 14 8.9 EUT PBVOY72 Top & Front View ............................................................................................................................................... 15 9 Requirement conditions table ........................................................................................................................................................... 16 10 Test results summary ......................................................................................................................................................…

Text truncated - open the document above for the full version.